I have HP LaserJet Pro M1536dnf Multifunction Printer and my problem with eprint "Not Connected"

i use eprint but after day show in site massage state Not Connected
to solve this problem turn off printer or hp web services and tern on and it work
but same problem after some hour show not connected
how can printer connected all time ?

Hey sfareg,
One thing you need to check is if your internet connection is intermittent. If it is not, you can follow these steps to give the printer a better connection.
1. Find your printer's IP address by printing a network configuration page.
2. Type you IP address into the address bar of your web browser.
3. Click on the network tab at the top of the page.
4. Look at the left hand side and click IPv4 under wireless.
5. Change the IP settings to Manual.
6. Enter the printer's IP address, your subnet mask, and your routers IP address or default gateway in the spaces.
7. Set the Preferred DNS to 8.8.8.8.
8. Set the Alternate DNS to 8.8.4.4.
9. Click apply.(You may need to refresh the page if it says processing for longer than a min and click apply again.)
The printer should have a better connection now.
Although I am an HP employee, I am speaking for myself and not for HP.
If I have resolved your issue, feel free to provide Kudos and make sure you mark this thread as solution provided.

Similar Messages

HP LaserJet Pro M1536dnf Multifunction Printer (unable to add print driver hpfax1, error code 87)

Hi, my printer HP LaserJet Pro M1536dnf Mfp, suddenly didnt work so i remove the printer, and downloaded a new driver http://support.hp.com/us-en/drivers/selfservice/HP-LaserJet-Pro-M1536-Multifunction-Printer-series/3974271/model/3974278#Z7_3054ICK0KGTE30AQO5O3KA30R1 once dowloaded, i run it and uninstall the printer, restart my pc, and proceed to installing. but in the process of installing a error occurr, saying that "Unable to add printer, error code 87", and that " HP Toolbox FX has encountered an error and can not recover. once i click ok. it tells me to restart my pc and reinstall it again. i did it for 8x, and still with the same error. please help really need a help right now. as my boss is going to kill me

Hey , Welcome to the HP Support Forums!
I understand that you're getting the error 'Unable to add print driver hpfax1, error code 87' when installing your HP LaserJet Pro M1536dnf Multifunction Printer on your Windows 7 computer. I would like to assist you today with resolving this install issue. Thank you for including all of the troubleshooting steps that you have completed prior to reaching out for support. At this time I am going to walk you through some additional software and driver troubleshooting steps. Please follow all of the steps below. If you're using your HP Laserjet through a USB Cable connection, please disconnect that cable now. Step one: Remove Driver: 1. Click on your Start menu 2. Select Control Panel 3. Select Programs and Features 4. When Programs and Features opens a list of programs installed on your computer will populate. Click on the 'Installed ON' tab at the top to change the date so the recently installed items show at the top. This will make it easier to manually locate the three HP Laserjet items you need to uninstall. 5. Next, look for the HP LJ M1530 MFP Series HP Scan, HPLaserJetHelp_LearnCenter, and HP LaserJet Professional M1530 MFP Series. If you see any 3 of these, or all 3 of these items, please click on them and select Uninstall. Once you have confirmed that those three items have been uninstalled, please close Programs and Features and proceed to the next step. Step 2: Clear Temp Files: Click on your Start menuIn the 'search programs and files' box located right above Start after you click on it, type %temp% and hit enter on your keyboardWhen the Temp folder opens, select Ctrl + A at the same time on your keyboard. Everything in this folder will now highlight.Select the 'delete' button on your keyboard. The Temp folder contains temporary internet files. No actual files or folders on your computer will be affected by deleting the Temp files. Should a Temp file still be used than you will automatically get the pop up to 'skip' that item.Close the Temp folder once it is emptiedRight click the Recycling Bin on your desktop and select Empty Recycling BinPlease proceed to the next step. Step 3: Download Installer Package: Please click here to download the Full Feature Installer package. Once the download is complete, click on the download to allow it to 'Run'An extraction should now automatically occur. Once the extraction is complete an installer window will open. Please close the installation window. You do not want to run the installation at this time. Step 4: Run Scrubber: To ensure that no trace of the HP Software and Driver package remain on your computer, I am going to have you run a Scrubber built into the installer package for your printer. Click on your Start menuIn the 'search programs and files' box located right above Start after you click on it, type %temp% and hit enter on your keyboardWhen the Temp folder opens locate the 7z folder. Click on this folder to open it. This is the HP Laserjet Installer Click on the Utilities folder under the 7z folderDouble left click on Scrubber. It is an application which should launch the HP Uninstaller. Please follow the onscreen prompts to complete the uninstaller. Once the uninstall has completed please proceed to the next step. Be sure to Restart your computer if the uninstall process prompts you to. Step 5: Check Print Server Properties: Click on your Start menuClick on Devices and PrintersIn the Devices and Printers window look for your HP Laserjet. If you see it listed please right click on it and choose 'Delete' or 'Remove Device'. Next, click on any device listed under 'Printers and Faxes' once just to highlight itClick Print Server Properties at the top of the windowClick on the Drivers tabLook for your HP Laserjet driver. If you see it click on it and click Remove at the bottomClick Remove Driver OnlySelect OKSelect Apply and OK on the Print Server Properties windowClose Devices and Printers. Please proceed to the next step. Step 6: Run Disk Cleanup Utility: Click on your Start menuSelect All ProgramsSelect AccessoriesSelect System ToolsSelect Disk Cleanup Run a Disk Cleanup on the C DriveWhen prompted, check Downloaded Program files, Temporary Internet Files, Recycle Bin, Temporary Files, and Thumbnails Once the Disk Cleanup is complete, please proceed to the next step. Step 7: Run CCLeaner: To ensure that there are no malicious files on your computer or Registry conflicts on your computer I am going to have you run a CCLeaner before we install your printer. Please click here to download the CCLeaner Tool. Once the website opens select the link at the top for 'Free Download'. Once the download is complete please complete the Scan. Should multiple malicious files be found you may need to run the Scan multiple times to remove all malicious files. Once your system comes back as clean, please proceed to the last step. Step 8: Install Device: Please click here to download the Full Feature Installer package for your HP LaserjetOnce the download is complete please allow the download to RunPlease follow the onscreen prompts to install your HP LaserjetIf using a USB Cable connection please do not plug in the USB Cable until the installer window prompts you to Once the installation has completed successfully please test your machine to confirm that everything is functioning properly. Please respond to this post with the result of your troubleshooting. I look forward to hearing from you. Good luck!

HP LaserJet Pro M1217nfw Multifunction Printer scaner driver problem in windows 7

I have a HP LaserJet Pro M1217nfw Multifunction Printer. Printer is ok but Scaner has problem in Windows 7 scaner driver is deleted when i try to scan it show the error " Scaner not communicate " I have to reinstall driver after few minitus again same problem . Pls advise me what is the best solution for that

Hi KrunalPatel,
I'll paste a link to a troubleshooting document below - from what I've read, it has the best chance at fixing your scanner errors, as it has the most steps to try
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02917811
Please let me know how it goes
*** If my reply was helpful, please click on the "Kudos Thumbs-Up" on the right, as a way to say "Thanks!".
If this reply also fixed your issue - please click the "Accept as Solution" button, so that others can find the same answer. ***

HP LaserJet Pro M1212nf Multifunction Printer Drivers

I have HP LaserJet Pro M1212nf Multifunction Printer And i lost the driver cd. Now i want to connect my printer to different pc which has windows 2002. What can i do? I didnt find any driver for this computer in hp drivers pages. Please help me...

Hello Burcu,
Welcome to the HP Forums!
I understand you're looking for a Laserjet M1212nf driver compatible for a Windows 2002 operating system. I will do my best to assist you! I will provide the HP website where all the full features drivers are available here. If your operating system isn't listed, then there are no drivers available.
The only suggestion I can provide is connecting a USB cable to this printer and your computer. Windows will detect the hardware and try to install a driver. If you have any further questions, please let me know. Have a great night!
I worked on behalf of HP.

How to print count page of HP LaserJet Pro M1214nfh Multifunction Printer

Hi there, I need to find out how to print counter of my printer, I mean the total number of printed pages.
my printer model is :
HP LaserJet Pro M1214nfh Multifunction Printer
thanks alot.

Hello motevalli69,
Welcome to the HP Forums.
To get the number amount of the pages printed, I am going to give you the User Guide for your printer. Please go to the section Table 2-5. Reports Menu.
I hope this is the information you are looking for.
Please feel free to write me back if you have any other questions.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

LaserJet Pro M1536dnf Multifunction Printers - A 'Firmware Corrupt Ready 2 Download'

LaserJet Pro M1536dnf Multifunction Printers - A 'Firmware Corrupt Ready 2 Download'
I run firmware files named that M1530_Series_FW_Update-20120629 file from network in Win.7 Then Firmware Corrupt Ready 2 Download is appeared. All operation blocked, pls help?

How was the printer connected to the computer? USB or networked?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

HP Laserjet Pro M1136 Multifunction printer installation problem

Dear Team,
Recently purchased HP Laserjet Pro M1136 MultiFunction printer. But it is not installing HP scan software. But scanner is working by default drivers.
Printer is not identifying when i am trying to install printer drivers.....?
System drivers updated and USB drivers also updated. But no luck
HP Scan doctor also installed. But same issue. HP scan is not identying
Printer connected to HP Omni 200 PC 5320il all in one system.
Windows 7 X64
Thanks
Solomon Dayakar G

Hello Solomon_ganji ,
Welcome to the HP Forums.
I see that you are having some issues when attempting to install the scanning software.
I suggest we start off by running the HP Print and Scan Doctor. Please let me know if the Doctor fails as well as any error codes you may see.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

I have a macbook pro 10.8.5 and the Application Safari will not open no matter what i do, I try to open the menu of Safari but it won't let me either, the mouse will just be loading. Each time i open it, it says "Application Not Responding"

I have a macbook pro 10.8.5 and the Application Safari will not open no matter what i do, I try to open the menu of Safari but it won't let me either, the mouse will just be loading. Each time i open it, it says "Application Not Responding" and I try opening it in my Finder and it'll say "The Application 'Safari' cannot be opened." and below that it'll say "-1712" Please help? I would really like to open it again.

The application Safari can't be opened -1712
What to do about "The application 'Safari' can't be opened" -1712 ?

HP LaserJet Pro M1217nfw Multifunction Printer - No TWAIN Compliant is installed.

I was trying to scan using the LaserJet Scan. However, I have received a message "There is no TWAIN-compliant device installed. Please install one and try again". I have searched on google but I was unable to find one. Please also note that I was also trying to uninstall the driver, but I was unable to do so because it stated that one or more of the printers listed above have pending print jobs. Printers with pending jobs cannot be removed until the jobs are completed.
Thanks for taking the time to read and respond to my post.

Hi Hoang714,
Thanks for providing that information.
Download the and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it.
Find and fix common printer problems using HP diagnostic tools for Windows?
Create a restore point on the computer. So this way we can always go back to that restore date.
Go to the start up screen, (tiles menu) type in restore point. Then follow the document provided.
How to Create a Restore Point in Windows 8.
Setting up the Administrator Rights on Windows 8.
Where Do I Change User Privileges in Windows 8?
Create a new profile. Create a user account .
On the Windows 8, hold down the Windows Logo key () on the keyboard and the 'R' to open the run box.
Check the Windows Image Acquisition Services:
On the Windows 8, hold down the Windows Logo key () on the keyboard and the 'R' to open the run box.
Type in services.msc and click on OK.
In the Window, please right click on Windows Image Acquisition Service and then click on Properties.
In the Properties window, please click on Dependencies window and check the dependencies.
It should be “Remote Procedure Call” and “Shell Hardware Detection”. If you find anything else, please advise.
Close the Properties window.
In the main Services window, in the list make sure Windows Image Acquisition Service shows 'Started' in the Status column and 'Automatic' for the Startup Type. If the option to stop is available, click stop and then click start.
In the main Services window, in the list make sure that Remote Procedure Call (RPC) shows as 'Started' in the Status column and 'Automatic' for the Startup Type.
In the main Services window, in the list make Shell Hardware Detection services shows as 'Started' in the Status column and 'Automatic' for the Startup Type.
If the other two in the services are not started, please restart these services and then restart the Windows Image Acquisition service. Just right click and select start on each one.
Temporarilty turn off the Antivirus software, since it may stop the services.
When you run the installation, right click on it and Run as Administrator.
I have provided some more steps, just in case you still are having the Twain error.
file being in the wrong directory when the install gets done.
Hence the scanning works from MSPaint or Windows Scan and Fax programs but not from HPs Scan App.
The directions are quite simple and are as follows:
Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box, type %temp%. You will see the 7z..... folder that extracted your web pack for the printer.
In this folder, navigate to drivers\scanner\x32\ folder.
Copy the HPWTIOP4.DLL from this folder.
Hold down the Windows Logo key () on the keyboard and the 'E' key. Then go to Program Files (x86)\HP\DigitalImaging\Bin folder and past the HPWTIOP4.DLL in there.
Try scanning again.
Let me know how you make out.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Printer Install Issues for HP LaserJet Pro M1212nf Multifunction Printer

After running the software it keeps telling me install failed check USB, power off then on and try again. I have done all of the troubleshooting methods on your website with no luck. The OS is Windows 7 Enterprise. Any help would be greatly appreciated.

@Neogio78
Thank you for your post on the hp.com forums.
Couple of questions: how were you originally installing the printer: USB, LAN cable, wirless? Which software did you try to install: Full Solution or the host based driver (basic print driver)?
My first suggestion would be to uninstall all software and make sure that you delete all the HP folders for this printer from your C:// drive. Reboot your system and try again.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

After upgrading from Trial to Monthly subscription plan I have the Adobe Pro crashing every time I open it, with a note" Acrobat quit unexpectedly". How can I make it work?

Hi,
Can anybody advise how I can make my Adobe Pro work? Now it it gives me a note "Adobe quit unexpectedly" each time I launch it. I have it on iMac. The trial version worked no problem, glitches started after I bought a monthly subscription.
Thank you in advance.

If you are on Windows, I would go to Control Panel>Programs & Features and do a repair.

I have a problem with Safari not connecting on my IPad with WiFi

IPad 3 or 'new IPad 'with cellular data. I have a problem with the WiFi not working more than a couple of times. When I check settings the connection is still showing as strong. To regain access to the Internet, I have to turn the WiFi off and then back on. Then it will work a time or two and stop again. I don't want to have to use my data plan when I am sitting right beside the router.
The WiFi signal is good, I have two laptops in the house that have no problem running on it with no interruptions.
Appreciate any help you can supply!

THanks, I tried all those and it is still the same erratic connection.
I also located the below information, and it didn't fix it either.
To reset the iPad's WiFi connection, simply use the option at the top of the screen to turn WiFi off. All of the WiFi settings will disappear. Next, simply turn it back on again. This will force the iPad to search for the WiFi network again and rejoin.
If you still have problems, you can renew the lease by touching the blue button to the far right of the network's name in the list. The button has a ">" symbol in the middle and will lead you to a page with the network settings.
Touch where it reads "Renew Lease" towards the bottom of the screen. You'll be prompted to verify that you want to renew the lease. Touch the renew button.
This process is very fast, but it could correct some problems.

HP LaserJet Pro M1217nfw Multifunction Printer –job prints repeatedly by AirPrint from iOS 6 devices

HP would like to make customers aware of an issue with its LJ M1217nfw and LJ M1218nfs printers. When using AirPrint from an iOS 6 device (e.g. iPhone or iPad) with the iOS 6 OS, the print job will print continuously unless the customer cancels the job manually.
The reason: the latest FW available on HP.com (version 20120901) does not support AirPrint from Apple iOS devices (e.g., iPhone or iPad) with iOS6 OS. This will be fixed in the next version of firmware.
To avoid this issue, please use this workaround while waiting of the fix in the next release of FW. The previous verion of FW (version20120206) for M1217nfw does not have this issue.
To deal with this issue, customer can select any one of the operations to terminate the print job:
Cancel job manually in ‘Print Center’ from iOS device
Double –click the Home button to display recently used apps
Swipe left or right to find ‘Print Center’
Tap ‘Printer Center’ and click ‘Cancel Printing’
Another option is to Power Cycle the printer.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution
This question was solved.
View Solution.

The lastest FW (FW 20130125) has been posted and fixed the above issue. Please download the lastest FW at:
m1217nfw FW link
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Printing and Sizing Problems with PDF Files

I have grading keys saved as PDF files. When I open them in the Adobe Reader X, some come up looking fine, fitting nicely on an 8.5" x 11" page and ready for print. Others come up looking shrunken and in the middle of the page. When I try to resize and print these, I get all kinds of funky results.
What I want to do is process all the PDF files (grading keys) so that they will fit nicely on the 8.5x11, without the user having to do a bunch a stuff resizing, etc.
I have included links to two PDF files below. The first comes up fine in the Adobe Reader and the sond does not. Can anyone help me with this perplexing issue? Thanks.
www.goodnewsjail.org/good.pdf (Formatted correctly)
www.goodnewsjail.org/toosmall.pdf (Comes up looking scrunched on the page)
Note: I might add that when I open these files in Adobe Photoshop CS, the one above that looks good comes up with dimensions 23.687"x17.745", while the one that comes up looking funky has dimensions 10.24"x7.85". I am as confused as a termite in a yo-yo.

Both of your documents have the same size: 279.4mm x 215.9mm. The difference is that the 'good.pdf' has its content evenly distributed over the available size, the other one has its content minimized in the center, with a large white space around it (in Adobe Acrobat).
As for why it shows a different size in Photoshop, I have no idea.
There is not much you can do about it with Adobe Reader, but you can change the size using Photoshop or Illustrator. See attachment to this post.

HP LaserJet Pro M1212nf Multifunction Printer Driver Installation Continuous Loop

HP LaserJet Pro M1212nf Multifunction Printe Driver Installation Continous Loop and No Installation
Thank you

ttb58,
At what point are you hitting this loop? What operating system are you running and what are the errors you are getting?
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

I have HP LaserJet Pro M1536dnf Multifunction Printer and my problem with eprint "Not Connected"

Similar Messages

Maybe you are looking for