I have hp620 its sound is very low although the volume is full.what should i do?

i have hp620 its sound is very low although the volume is full.what should i do?? 
Please Help!! 

There's a countless number of volumes on the iPhone.
The Main volume, On-Call volume, Music volume, Siri volume, Directions volume, etc. etc.
While On-Call with an individual or Voice Mail for example, make sure you're holding the up button to it's maximum.

Similar Messages

  • Voice memo volume very low, it played normally then today very low even with volume set full blast.

    I played my voice memos yesterday and the volume was fine.  Today I can bearly hear them.  I have the volume set to the highest with the buttons on the side.  Any thoughts?
    NCMead

    Hello NCMead,
    Thanks for using Apple Support Communities.
    I'd like you to take a look a the follow support article, specifically starting at step 5:
    Verify that the volume is set to a level you would normally be able to hear.
    Ensure that there is nothing plugged in to the headset jack or the dock connector.
    If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
    Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
    If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
    If the iPhone is paired with a Bluetooth headset or car kit:
    Try turning off Bluetooth.
    If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
    Restart the iPhone.
    If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
    If the issue is not resolved, please contact Apple Support.
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/ts5180
    Take care,
    Alex H.

  • My mac makes a typewriter sound when I use my mouse.  It is not speaker related, the sound continues after I turn the volume down.  What is this and how do I make it stop?

    My mac has just started making a sound similar to an old fashioned typewriter while I an on line using the mouse.  It does not seem to make this sound while I am using the keyboard.  It is likely electrical because it continues even when I have turned the speaker volume down.  Does anyone know what may be causing this and how it can be stopped.
    Thanks

    Open your mac pro and listen carfully.  It could be coming from a failing hard drive or a bad fan.  If you have more than one drive you could remove the ones you are not currently using and add them back one by one to try to localize or eliminate the sound.  Caution though, only remove drives when your machine is off.  You cannot hot swap the drive bays.

  • HT1481 My ipod's sound quality has changed and its sound's very low. How should I fix it?

    Dear sir,
              My ipod once got formatted. Now I hear low sound from my ipod.

    First, make sure your headphones are working properly.  You can try them with another device, or try a different set with your shuffle.
    If the headphones are fine, go to the shuffle's Settings or Summary screen in iTunes.  It's the screen that appears when you select the shuffle in iTunes.  There is a Limit maximum volume setting there.  Make sure that slider bar did not get set to a low volume.
    If that does not help, you can try doing a Restore on the shuffle in iTunes.  The Restore button is on the Settings or Summary screen in iTunes.  This will erase the shuffle, re-install its software, and set it to default settings.  If the cause is related to a problem with software or settings, the Restore should fix it.
    If that does not help either, there may be a hardware-related problem on your shuffle.

  • I've an iphone 4, its headset jack is not working properly, when i insert the earphone no sound is coming, but when i keep the earphone little out i can hear the sound but very low sound is coming out, I've never dropped my iphone please help...

    I've an iphone 4, its headset jack is not working properly, when i insert the earphone no sound is coming, but when i keep the earphone little out i can hear the sound but very low sound is coming out, I've never dropped my iphone please help...

    bunjamin wrote:
    There is now a new line in BBM that wasn't there before which covers the message that I am typing, so I can't actually see what I am typing.
    Hi bunjamin,
    just go to BlackBerry World, and update all your apps including BBM.
    bunjamin wrote:
    Every time I unlock my phone, my screen enlarges so I can't really see much on the hub/notification screen and it defaults to the hub which it didn't do before).
    you can turn off the magnifying glass :
    device settings >> accessibility >> magnify mode >> OFF
    you can deactivate the "reset to Hub view" :
    hub >> overflow (bottom right button) >> Settings >> Display and actions >> Return to Default View When Idle >> OFF
    bunjamin wrote:
    my ringtone is much softer than it was previously
    yes, BlackBerry has acknowledged this bug in this article from the public knowledge base:
    KB36755 After upgrading BlackBerry 10 OS to version 10.3.1 the volume for notifications is noticed to be significantly lower than in the previous version
    The search box on top-right of this page is your true friend, and the public Knowledge Base too:

  • Iphone 6 Plus audio sound is very low

    I am using 16 GB iphone 6 plus and i am facing audio problem.During phone call,sound is very low and i have to have on the speaker to listen audio properly.

    Hi ayush gaur,
    If you are having an issue with poor sound quality from your iPhone I would suggest that you troubleshoot using the steps in this article - 
    If you hear no sound or distorted sound from your iPhone, iPad, or iPod touch speaker - Apple Support
    Thanks for using Apple Support Communities.
    Best,
    Brett L 

  • I use itunes on a Dell XPS502 with W7/64. In some cases have have problems to import CD's. The sound is very disturbed and the import need a lot more time than in normal cases. Is there a problem between itunes W7/64 or a known hardware issue?

    I use itunes on a Dell XPS502 with W7/64. In some cases have have problems to import CD's. The sound is very disturbed and the import need a lot more time than in normal cases. Is there a problem between itunes and W7/64 or a known hardware issue?
    Example-CD : "Tracy Chapman , Telling stories" is not able to import . I have more such negative cases. But in other cases it works fine and the sound is great.
    The firmware at the inbuild CD/DVD DS-6E2SH is the latest version.
    What can I do??

    hi b noir,
    I don't no about virtuel drives like you mententioned. In the mean time I have rebooted the XPS and run again the iTunes diagnostics. I think the back - chance in the registry was not ready to use.  Now there are another results. They are the same in case of a running CD or a not running CD. The difference in total is like before. It takes more time that iTunes reads the (bad) CD and at the there is no good sound. In both cases ( running or not running CD) iTunes diagnostics gives as a result :
    (the copie from ITunes shows the result of the not running CD from Tracy Chapman)
    Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
    Dell Inc. Dell System XPS L502X
    iTunes 10.3.1.55
    QuickTime 7.6.9
    FairPlay 1.11.17
    Apple Application Support 1.5.2
    iPod Updater-Bibliothek 10.0d2
    CD Driver 2.2.0.1
    CD Driver DLL 2.1.1.1
    Apple Mobile Device 3.4.0.25
    Apple Mobile Device Treiber 1.55.0.0
    Bonjour 2.0.5.0 (214.3)
    Gracenote SDK 1.8.2.457
    Gracenote MusicID 1.8.2.89
    Gracenote Submit 1.8.2.123
    Gracenote DSP 1.8.2.34
    iTunes-Seriennummer 00D7B2B00CD25750
    Aktueller Benutzer ist kein Administrator.
    Aktuelles Datum und Uhrzeit sind 2011-06-11 19:33:22.
    iTunes befindet sich nicht im abgesicherten Modus.
    WebKit Accelerated Compositing ist aktiviert.
    HDCP wird unterstützt.
    Core Media wird unterstützt.
    Info zu Video-Anzeige
    NVIDIA, NVIDIA GeForce GT 540M
    Intel Corporation, Intel(R) HD Graphics Family
    **** Info für externe Plug-Ins ****
    Keine externen Plug-Ins installiert.
    iPodService 10.3.1.55 (x64) arbeitet zurzeit.
    iTunesHelper 10.3.1.55 arbeitet zurzeit.
    Apple Mobile Device service 3.3.0.0 arbeitet zurzeit.
    **** CD/DVD-Laufwerkstests****
    LowerFilters: PxHlpa64 (2.0.0.0),
    UpperFilters: GEARAspiWDM (2.2.0.1),
    D: PLDS DVDRWBD DS-6E2SH, Rev CD11
    Audio-CD im Laufwerk
    11 Titel auf der CD gefunden, Spieldauer: 42:07 auf Audio-CD
    Titel 1, Startzeit: 00:02:00
    Titel 2, Startzeit: 03:59:47
    Titel 3, Startzeit: 07:19:27
    Titel 4, Startzeit: 11:31:30
    Titel 5, Startzeit: 15:31:50
    Titel 6, Startzeit: 20:07:50
    Titel 7, Startzeit: 24:27:15
    Titel 8, Startzeit: 27:49:10
    Titel 9, Startzeit: 32:41:25
    Titel 10, Startzeit: 35:29:65
    Titel 11, Startzeit: 38:38:00
    Audio-CD erfolgreich gelesen (Suche nach alter Firmware).
    Laufwerksgeschwindigkeit erfolgreich erkannt
    Die CDR-Geschwindigkeiten des Laufwerks sind:  4 10 16 24
    Die CDRW-Geschwindigkeiten des Laufwerks sind:  4
    Die DVDR-Geschwindigkeiten des Laufwerks sind:  4
    Die DVDRW-Geschwindigkeiten des Laufwerks sind:  4
    After starting the import it is going slower and slower. If it is helpful I can send you a soundfile with these distortions.
    best regards
    tcgerd

  • Audigy 2 ZS Bad Sound. Very low Volu

    Hello,
    I'll start out by listing my system hardware. Additionally everything is up-to-date including BIOS, Drivers and Operating System
    MSI nForce 4 Ultra
    AMD Athlon 3000+
    2GB of RAM (4x52)
    Sound Blaster Audigy 2 ZS
    Microsoft Windows XP SP2
    I don't think the rest of the configuration settings are needed...
    My problem is as follows. Recently after a restart I noticed that the sound was really low while watching a DVD. I turned up the volume not only on the computer but also the CreativeWorks THX 550 speaker system I have. I was then able to hear the sound; however it sounded like the volume was maxed on the computer, distorted, but the overall decibel volume was low. Of course I thought it was a connectivity issue. I tried many things. My first attempt was to check the cabling. My next step was to relocate the PCI Card. I disconnected and reconnected everything. My third attempt was to put it in a different computer... Here's the interesting part. I don't have any other PC's available at the moment only two linux boxes and a Mac. So I took an older sound card I had (Sound Blaster Li've) and plugged it into my PC. Same issue! The overall decibel volume was low, yet the sound was distorted as if the volume was to loud.
    My next step went along the lines of testing sound on the board. I went into the BIOS and enabled my onboard sound card. That worked fine. I then reinstalled the Audigy Card. After installing I tried to see if sound was being processed correctly. Now I"m not an expert on this but I would assume sound passing through the card is emulated directly out through the Digital Out. I hooked it into my Digital Optical Recei'ver and everything worked find... That's not a solution. The Audigy has a little latency issue.
    I've tried reinstalling drivers, changing my overclocking from off to full to dynamics in between. I'm at a lost here. One would think this is a PCI issue; perhaps maybe IRQ... But I doubt it.Message Edited by SIRKGM4vg on 07-29-200703:8 PM
    Message Edited by SIRKGM4vg on 07-29-200703:29 PM
    Message Edited by SIRKGM4vg on 07-29-200703:30 PM

    First unistall Creative stuff through add remove programs.
    Next run Guru3D driver sweeper and double check the log for failed removals.
    Next uninstall Creative hardware in Windows device manager. (also tick "delete the driver software for this device")
    After that, you should have deleted everything!
    As for "the best drivers", both are (the same but) different and it depends on what you want to use your card for. Both work fine wth ALchemy and both get the job done.
    daniel_k's latest drivers have equalizer, louder volume and advanced CMSS. daniel_K also has a few hybrid ISO with DVD audio, MIDI and other valuable applications. They don't always perform as they should though for obvious reasons (NO OFFICIAL CREATIVE VISTA SUPPORT - XP applications - No Hardware Audio).
    nomoregoatsoup are just recent X-Fi drivers and a basic Creative Audio console. They offer improved sound quality over the official version and also offer limited DTS/SPDIF options like the Dell counterparts.
    All current Audigy Vista drivers are inferior compared to XP ones.

  • When I play either music or movies on my ipod touch it stops every few seconds and I have to restart the song/film.  AT the same time, it won't hold a volume contol.  It jumps louder or softer, or simply jams on either very low or maximum volume.  Help

    When I play either music or movies on my ipod touch it stops every few seconds and I have to restart the song/film.  Also, it won't hold a volume contol.  It jumps louder or softer, or simply jams on either very low or maximum volume.  Help?

    No one here is going to do anything about it. Send feedback to Apple.
    http://www.apple.com/feedback/ipad.html
    Basic troubleshooting steps. 
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 

  • I'm having trouble with the volume of my i phone 4s when using headphones, the sound will only appear when the volume is at its highest, any lower and all I hear is static. Can anyone help me with this problem? Much appreciated.

    Hi, I'm using a white iPhone 4s with 16gb memory and having some problems. Whenever I use earphones the sound will be heated when the volume is at the highest if I turn it down any lower all I hear is static. Can anyone help me with this problem as I would appreciate it much.

    Reset the device:
    Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
    If that doesn't help, tap Settings > General > Reset > Reset All Settings
    No data is lost due to a reset.

  • Iphone 5 not making sounds - or very low volume

    I had an iphone 4 for over 3 years and it was perfect.  I upgraded to an iphone 5 and now constant issues with the volume of tones for text, phone and even sending tone.  It just randomly mutes completely or goes to a volume that you can barely hear.  All volume controls are at high, the do not disturb is turned off, the mute button is not on.  The only thing that fixes this is to power off the phone and turn back on.  This is highly aggravating as first I have to miss calls and text to realize the volume isnt working again and then power it down again.  This is occuring daily.  If I do use the mute button at all as soon as I turn it from mute to on I have to power it down as the tones dont work.  Why is this happening?

        Hi doonmeister,
    Not having service (calls & texts) at all must be very frustrating! It appears that you have done most basic troubleshooting and issue persist. I see that your post is dated November 19; I trust that you called us at 800-922-0204 from other line already and the issue has been resolved by now. Please keep in mind that this is a peer to peer forum and while our Social Media team monitors the posts, the best way to get immediate assistance for critical issues (such as inability to call/text) is to call us from a different line to troubleshoot your device, or send us a message on twitter @VZWSupport at your convenience. If you still need assistance with this service issue please follow me and send me a direct message including your full name as it appears on your account and your wireless number. I'll check the area for service alerts and follow up with you.
    AntonioC_VZWSupport
    Follow us on Twitter at www.twitter.com/VZWSupport

  • Pls its very urgent - i dropped by iphone 3G and the display became very dim soon after and it still remains the same - pls advise what should be done to bring the display back to normal

    Pls its very urgent - i dropped by iphone 3G and the display became very dim soon after and it still remains the same - pls advise what should be done to bring the display back to normal

    sounds like you broke the display when you dropped it.  There's nothing we users here can do for you.
    Since the iPhone warranty does not cover accidental damage, you will have to pay to have your phone repaired or replaced.  You can bring it into Apple for an out of warranty exchange in the country of purchase, or you can find a 3rd party iPhone repair store in your area.

  • I had my ihone unlocked bt i forgot to sync it to itune before i went on Holiday. now its not working on any of the pc's here what can i do i stil have 3 wks to go!! plz help

    i had my ihone unlocked bt i forgot to sync it to itune before i went on Holiday. now its not working on any of the pc's here what can i do i stil have 3 wks to go!! plz help

    I think you will need to restore to the itunes computer you normally sync to.
    So you'll have to wait until you come back from your trip.

  • Hi,have you ever met such problem- one side of the display a bit lower than another,it is new, what should i do ?

    Hi,have you ever met such problem- one side of the display a bit lower than another,it is new, what should i do ?

    Call Apple Support

  • How can I find my lost ipad-2 with WIFI only. I have only its serial no. icloud says alway the device is offline

    how can I find my lost ipad-2 with WIFI only. I have only its serial no. icloud says alway the
    device is offline

    It will only show if the device is turned on. And if someone else has it, they can turn that feature off. Your best options are to return to the location where you think you lost it, and see if anyone returned it. Also contact your local law enforcement.
    Reporting a lost or stolen product
    http://support.apple.com/kb/HT2526
    Report to police along with serial number. Change all your passwords.
    These links may be helpful.
    How to Track and Report Stolen iPad
    http://www.ipadastic.com/tutorials/how-to-track-and-report-stolen-ipad
    Reporting a lost or stolen Apple product
    http://support.apple.com/kb/ht2526
    Report Stolen iPad Tips and iPad Theft Prevention
    http://www.stolen-property.com/report-stolen-ipad.php
    How to recover a lost or stolen iPad
    http://ipadhelp.com/ipad-help/how-to-recover-a-lost-or-stolen-ipad/
    How to Find a Stolen iPad
    http://www.ehow.com/how_7586429_stolen-ipad.html
    Apple Product Lost or Stolen
    http://sites.google.com/site/appleclubfhs/support/advice-and-articles/lost-or-st olen
    Oops! iForgot My New iPad On the Plane; Now What?
    http://online.wsj.com/article/SB10001424052702303459004577362194012634000.html
    If you don't know your lost/stolen iPad's serial number, use the instructions below. The S/N is also on the iPad's box.
    How to Find Your iPad Serial Number
    http://www.ipadastic.com/tutorials/how-to-find-your-ipad-serial-number

Maybe you are looking for