I have Internet speed 1 GB but Time Capsule last generation is share wifi maximum speed 200 Mb.

I have a TC ME177/LL/A and an Internet speed of 1 GB. My TC is working on WiFi with maximum speed of 200 Mb. Is anybody which has same problem and fix it?

You cannot get even close to your 1GB speed with an Apple router.. that are just not fast enough even on ethernet.. on wireless you can expect a very substantial drop.. 200Mbps is hugely fast internet for wireless to a router.. and that does indicate an actually connection speed (link rate) of something in the order of 600-800Mbps.. wireless is also another form of politics.. it is how to tell lies.. and when found out.. tell even bigger ones to cover it up.

Similar Messages

  • Time capsule (1st generation) like a wifi repeater?

    Hi,
    I'd like to use my time capsule like a wifi repeter.
    How i must configure it?
    Thank you

    I have just purchased a new Airport Extreme to take advantage of the new wifi AC functionality.  I currently have my old Time Capsule connected via Ethernet cable to the Extreme.  I have it in Bridge Mode with the wireless off so that it is just a back up device.  My son has an older ipad that does not work in some parts of the house.  The Airport Extreme is in the basement and provides great coverage for everything except the ipad.  My wife would rather I did not clutter the main floor with more wires and devices so I am trying to avoid moving the Extreme from its current position.  I was thinking I could run a long Ethernet cable to the time capsule and reposition it in a different part of the basement to hopefully cover the ipad deficiency.  What are the settings for the Time Capsule to make this happen?  From what I have been able to tell from other posts it needs to still be in bridge mode, but I am not sure what the wireless settings should be.  New wireless network? extend wireless network? Do I keep the wireless name I created with the new Extreme?  Thanks

  • I have just bought an airport time capsule and im trying to install an airport utility. I tried the 6 version but it wd not load because it said might mac would not support. I then tried the 5.6.1. and it said it would not work with airport capsule.

    I have just bought an airport time capsule and i am trying to install an airport utility programme to support this
    However, it seems the version 6 which came out last year - i can't use on my Mac - Snow Leopard -
    So tried to then install version 5.6.1 and although this installed properly, it says this will not support my capsule
    2. I have BT home hub 2. I presume I cannot bypass this as the internet router? I bought the time capsule for its capability to back up . The router was a byproduct. But am I correct in thinking that it acts as a secondary router or a booster rather than a primary router . I still need the BT homehub?
    if anyone can help that would be great
    CS J

    You should either return the Time Capsule or upgrade your Mac at least to OS X 10.7.

  • I have just installed a 2TB time capsule on my iMac i7, it see my second 1TB hard drive but the 256 SSD doesn't come up in the list of hard drives I can back up. How can I enable the time machine to see my first SSD 256gb hard drive?

    I have just installed a 2TB time capsule on my iMac i7, it see my second 1TB hard drive but the 256 SSD doesn't come up in the list of hard drives I can back up. How can I enable the time machine to see my first SSD 256gb hard drive?

    iLife is preinstalled on all the Macs. If you purchased iLife in the App Store or your computer came without DVDs, open App Store > Purchases and download the applications. If your Mac came with discs, insert the Applications DVD and install iLife applications

  • I just purchased a 3TB Time Capsule.  I live in Italy and have 220V power.  The Time Capsule is rated for that, but the cord says 125V.  Can I use this cord with an adapter, or do I need to buy a new cord at an Italian store?

    I just purchased a 3TB Time Capsule.  I live in Italy and have 220V power.  The Time Capsule is rated for that, but the cord says 125V.  Can I use this cord with an adapter, or do I need to buy a new cord at an Italian store?

    Due to the kind of plug used the US power cord is rated at the 125v value.. and legally we cannot advise you to use on higher voltages.. although I have never had issues in Australia.. 240v.
    But adapters from your Euro power plug to US are generally ugly .. unsightly things.. and often sit high above the socket and are none too stable.. I agree with Bob.. just go out and buy a standard figure 8 power cord.. check with Apple in Italy for a white one.. if you are going to have it on show.. black are far more common. Or even check ebay for a standard power Apple power cord as a number of items they sell use the figure8 socket. 

  • Can anyone tell me how I keep everything I had in my old photoshop, now I've updated to Photoshop CC 2014.  It did give me the option to transport over all my presets, but because I didn't have internet access at the time, it couldn't do it.  Now I'm not

    Can anyone tell me how I keep everything I had in my old photoshop, now I've updated to Photoshop CC 2014.  It did give me the option to transport over all my presets, but because I didn't have internet access at the time, it couldn't do it.  Now I'm not getting the option.  Please help.

    Migrating Presets does not require a network connection and you can still migrate your cc presets if you still have CC installed.  Use Photoshop menu Edit>Presets>Migrate Presets...  Migrating presets only migrates presets.  It does not migrate Plugins, settings, extensions and scripts.  CC 2014 is also not completely backwards compatible with CC.  Support for Flash Panels and Oil Painter filter have been removed.  So extensions like mini bridge no longer work in CC 2014

  • How do I setup my Time Capsule (3rd Generation) to be accessed from the internet while I'm traveling?

    How do I setup my Time Capsule (3rd Generation) to be accessed from the internet while I'm traveling? It is installed on my home network behind my TWC broadband router.

    Ok.. since the TWC modem is also a router.. all configuration takes place on this box.. NONE whatsoever takes place on the TC.
    There is no airport utility 7.7.3 but there is a firmware of that number for the latest AC model TC..
    Is it tall like this.
    Then it is Gen5.
    otherwise it will have a firmware.. 7.6.4 or earlier and the airport utility must be 6.3 or earlier.
    Open the Airport utility and give us a screenshot of the summary page.
    That will also help us determine that you have the TC, which version and how it is setup.
    You might want to press the edit and also give us the Internet and Network tab as they should be set correctly as well.
    I have created a DDNS through DYN.com although I am not sure how to implement this into the TC.
    You do not do anything in the TC.. set it up in the Ubee router.
    Port forward 548 to the TC in the Ubee router.
    And make sure the TC has a static IP in the Ubee router.
    Overall if you find this too hard I strongly recommend you buy a product designed for remote access .. eg WD MyCloud.. they are cheap and easy peasy to setup for remote access.. by PC or Mac and since it is built outside of Apple you not bound up in Apple limitations built into all their equipment to prevent you using it the way you want.. rather than apple want you too.. eg BTMM and iCloud being the only way apple provide for access to the TC and only when it is the main router of the network.
    You are fighting hard because Apple made this hard.. not easy.

  • I have a macbook pro and time capsule.  Computer hard drive is full and I would like to expand wirelessly.

    I have read many forums that note an external hard drive can be connected to a time capsule, but it sound like that is just a way to expand the time capsule and not the computer hard drive.  The reason I would prefer a wireless option is to keep the laptop portable around the house (we have apple t.v. and home theater system that syncs wirelessly to itunes).  Wireless would allow use of any device even with the hard drive not being hard connected to the laptop.  Are there any options out there or am I just misunderstanding what happens when connecting a hard drive to the time capsule.
    I am not concerned about speed, but would hope any solution would still allow back up to the time capsule.
    Thanks!!

    You cannot expand the computer's hard drive by connecting an external drive to a Time Capsule. All that does is provide separate external storage. It will not expand the size of your computer's drive. To do that you have to buy a larger hard drive for the computer. Or you can buy an external drive then copy files you don't need to the external drive and erase them on your internal drive.
    Freeing Up Space on The Hard Drive
      1. See Lion's Storage Display.
      2. You can remove data from your Home folder except for the /Home/Library/ folder.
      3. Visit The XLab FAQs and read the FAQ on freeing up space on your hard drive.
      4. Also see Freeing space on your Mac OS X startup disk.
      5. See Where did my Disk Space go?.
      6. See The Storage Display.
    You must Empty the Trash in order to recover the space they occupied on the hard drive.
    You should consider replacing the drive with a larger one. Check out OWC for drives, tutorials, and toolkits.
    Try using OmniDiskSweeper 1.8 or GrandPerspective to search your drive for large files and where they are located.

  • My Time Capsule suddenly slowed my wi-fi network speed. Any clue?

    Don’t bother with my strange printer name login. I did something wrong in the past and I am not able to change it. Anyway, my problem seems to be more common than I thought. My wi-fi network suddenly lost speed. Directly connected to the cable modem I get full dow/uoload speeds but through Time Capsule I only get 20x lower download speed (strange but uoload is less affected).
    Tried almost everything already: soft and hard resets, channel changes, firmware updates and nothing changes.  I talked to the Apple support here in Brazil and seem to be lost on the problem. Any final solution for an apparently quite common problem? I am already considering to buy a new router…
    Thx,
    ECastro

    Do yet another factory reset.. sorry!! But we need to start from a known baseline.
    And tell us what version your TC is?? A1xxx from the rubber foot.
    Setup wireless to meet SMB rules.. Wireless name is short, no spaces, pure alphanumeric.
    Set a different name for 5ghz. Same rules.
    Set TC name also to the rules.
    So you have for example.. TC named TC
    2.4gz named TC24ghz
    5ghz named TC5ghz
    Use WPA2 Personal secuirity with password that is 8-12 characters pure alphanumeric.
    Update and put the TC back into the network in either bridge or router mode.. those are the only suitable modes.. and TC has to be set to create a wireless network.
    Now connect a laptop to the 5ghz wireless signal from the same room as the TC and measure your speed.
    Test again over ethernet if the wireless is slow.. if both are slow the TC is faulty or simply doesn't work correctly on your kind of broadband. This is now happening with fibre connections.. Apple have not updated the routing part of the firmware for ages.. and are ignoring the issue. Get a different brand router and bridge the TC for TM use only.

  • Time capsule 1st generation loosing Internet connection

    I have a time capsule 1st generation on my iMac. Since I updated to Lion, my time capsule started to flash orange every hour or so… it's extremely annoying and I really have NO idea what to do.
    Here's some specs and configuration for my network
    Firmware: 7.5.2 (75200.14)
    Wireless Security: WAP2 Personal
    Allow this network to be extended CHECKED
    Channel: Automatic
    Radio Mode: 802.11n only (2.4GHz) - I tried on 5GHz only and I had the same problem.
    Multicast Rate: 6Mbps
    WPA Group Key Timeout:  1 hour - I tried 1 day, 10 days, X months, doesn't matter, problem still here
    Create a closed network - UNCHECKED - Because the mac mini keeps on "forgetting" the network and it ***** to remember such a long password so I decided not to hide it anymore
    Since the time capsule is pretty close to my computer, I use an ethernet cable but everything else in the house is Wireless (iPhone, iPod Touch, iPad, Mac Mini, apple tv, Macbook Pro and Macbook)

    I found out that if you are already in airport when the problem starts, it doesn't update the message but the light gets amber and you loose connection for more or less 15 seconds.
    I got this issue again this morning, opened up airport and got 2 messages... then it went back online as if nothing happened. It's doing this every single hour.
    Since I can't plugg on wifi only since I ALSO get the "No Hardware Installed"  message in wifi, I have to be plug with the ethernet cable
    Am I the only one starting to REALLY hate Lion or what? None of this was happening on Snow Leopard...

  • Can't back-up new iMac with fusion HD.  The back-up proceeds to within 10% of the total storage needed and then the "of" number increases.  I suspect there is a problem with backing up the fusion drive.  We have a new 3 TB time Capsule.  Any ideas?

    Can't back-up new iMac with fusion HD.  The back-up proceeds to within 10% of the total storage needed and then the "of" number increases.  I suspect there is a problem with backing up the fusion drive.  We have a new 3 TB time Capsule.  I tried excluding different parts of the software from the back-up but it didn't make any difference.  I even tried exluding "invisible items" to no avail.  Any ideas?

    When you setup the wireless and ethernet in the computer.. ipv6 will be on automatic.. this is wrong for the latest TC firmware and airport utility. http://support.apple.com/kb/TS4597
    Go to the wireless and ethernet setup in preferences and change ipv6 to link local.
    Once you do the big backup by ethernet the wireless will function fine for incremental.. it is obviously not estimating the size correctly..
    A full back-up on the iMac would be about 650 GB.  The partial updates that I have been trying start out at 115MB and keep growing indefinitely.  The original back-up never finished nor have any of the follow-up attempts.
    The first estimate should be the full backup but it will keep growing as the backup advances.. I would also delete any inprogress files to make sure it is not messing up .. delete even a sparsebundle if there is one for the imac on the TC and start afresh once you have ethernet connection.
    See A10 here.
    Pondini may have some other clues there to give you an idea of why the backup is slow or not finishing.. there is a lot of issues with TM when it decides not to work.

  • Do i have to hardwire connect the Time Capsule to my router?

    do i have to hardwire connect the Time Capsule to my router?
    My plan was to just add it to my wireless network and keep it for security away from my mac and in a completely different part of the house.

    You can but it is a NOT recommended method.. it will be slow and unreliable.

  • My 'old' files have been backed up onto time capsule (Leopard), I have upgraded to Lion (thro snow leopard) and now checking back to retosre some old files i can't see or access beyond the date I upgraded to Lion? Help please?

    My 'old' files have been backed up onto time capsule (Leopard), I have upgraded to Lion (thro snow leopard) and now checking back to retosre some old files i can't see or access beyond the date I upgraded to Lion? Help please?

    Use the manual methods.. but it is possible for TM to wipe the old files in trying to fit into the space.
    Try Q16.. but read all the section 14-17
    http://pondini.org/TM/FAQ.html

  • The Apple time capsule provides disc memory, a wifi network, and router functions. It would normally be connected to the internet via cable modem.  If I wanted to use a wireless cellular connection to the internet, how would I do that?

    The Apple time capsule provides disc memory, a wifi network, and router functions. It would normally be connected to the internet via cable modem.  If I wanted to use a wireless cellular connection to the internet, how would I do that?

    If I wanted to use a wireless cellular connection to the internet, how would I do that?
    The wireless cellular device would need to have an Ethernet port, to provide an Ethernet signal to the Time Capsule's WAN port.

  • I lose my Internet connection, unplug my Time Capsule for a while,  plug it back in and get my conne ction back.  What may be causing that?

    I lose my Internet connection, unplug my Time Capsule for a while, plug it back in, then in a few minutes my Internet is connected again.  Can someone tell me what to do?  Thanks

    I was being jovial..
    SL is snow leopard.. If you are on 10.6.8 you are on SL. Your initial post says 10.5.6 but I assumed you had upgraded to Lion or worse Mountain Lion.
    Don't whatever you do update.. that is out of the frying pan into the fire.
    You might need to give more network info..
    What is the TC plugged into for broadband.. are you on cable, adsl, other.. is the TC in router mode.
    I find with SL, the later versions of TC firmware much worse than earlier ones.. So I do recommend you check your TC and if you are on 7.6.1 then downgrade to 7.5.2 .. you do this by holding the option key when you select update firmware.. it will show you downgrade options as well as upgrade.. only this is not possible with newest Gen 4 TC which are stuck on 7.6.x firmware.
    How do you connect to the TC is the other question.. and with what?? Is this issue computer only or iphone ipad etc. ie is your network wireless or ethernet (or both) does the issue affect both?

Maybe you are looking for

  • Problem with Context in mapping

    Hi. I  have a big problem with my mapping. My input look like this.: - <Rec> - <raw>   <Rec_type>B</Rec_type>   <Record_data>0000340H150000006269 N2007020105070000727001000009000540006599350000000000</Record_data>   </raw> - <raw>   <Rec_type>C</Rec_

  • Accidently deleted all items in itunes

    I accidentaly deleted everything in my itunes and I cannot find them in my recycle bin but everything is still on my ipod, how do I put everything back onto my itunes?

  • Top of List event when using class cl_salv_hierseq_table

    Hi all,   I am using above class to display Top of List . I am to able to display one line at top using following : gr_hierseq->set_top_of_list( lr_content ). But i have to display 5 lines in top of list. Please let me know how can this be achieved.

  • Oracle Report 6i Exceute Slowly

    I am working Oracle 9i with Oracle Developer 6i. O/S is Windows 2003 (Standard Edition) with service pack 2. Physical memory is 2 GB.When I execute a report it takes much more time. Further I noticed that to open Report builder it also takes lots of

  • XML example file in a comment

    Hi, i need to know how to put a little XML example file in a comment. This is what i have : * to be consulted. Next you can see an example of a configuration file : *<P> * blablablablalbablablabla *</p> * <br> * <?xml version="1.0" encoding="utf-8" ?