I have iOS7 on my iPhone4. I turned on the Voice Over option and now my phone is not working at all. At first it was freezing and not accepting any commands. Now all I have is a blank sceen. I can't get back into it. Any ideas what happened here?

I have iOS7 on my iPhone4. I turned on the Voice Over option and now my phone is not working at all. At first it was freezing and not accepting any commands. Now all I have is a blank sceen. I can't get back into it. Any ideas what happened here?

Hi Jeffny01,
If your iPhone is not responding, you may find the following article helpful:
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Regards,
- Brenden

Similar Messages

  • TS3274 I just updated my Ipad to I0S 7.02 like it asked me too. Now i have a black screen Itunes logo and a picture of the plug in cord. I can't get to my home screen. What happened?

    I just updated my Ipad to I0S 7.02 like it asked me too. Now i have a black screen Itunes logo and a picture of the plug in cord. I can't get to my home screen. What happened?

    You are in Recovery Mode. Follow the instructions below to recover your iPad.
    1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
    If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
    3. While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button.
    5. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
    Note: You need to be patient and repeat the above many times to recover your iPad. Data will be lost.

  • I recently got a an iPod 5 generation as a gift and while I was in my settings I turned on the voice over  to check the percentage of my battery, so I turned it off and now I can't unlock it. Even when scrolled my fingers on the screen and typed the pa

    I recently got a an iPod 5 generation as a gift    and while I was in my settings I turned on the voice over  to check the percentage of my battery, so I turned it off and now I can't unlock it. Even when scrolled my fingers on the screen and typed the password but it would unlock, please can some one help me with this

    You have the accessibility VoiceOver feature turned on.
    Triple click the home button and try going to Settings>General>Accessibility and turn VoiceOver off. You may have to use three fingers to scroll the screen to get there. If problems see the following for how to turn off via iTunes:
      iPhone: Configuring accessibility features (including VoiceOver and Zoom)

  • I tried to turn off the voice over thing on my iphone and now the screen is completely dark i don't know what to do now

    i tried to turn off the voice over thing on my iphone and now the screen is completely dark i don't know what to do now...help! ima go crazy without out my phone

    ok so this is what i did i finally got it to work...so i taped the black screen with 3 fingers and then it went back to normal and it ****** me off because i had tryed that already so when it goes back to normal even if the voice over is still on it is easy to turn it off if you follow the steps....lol i googled how to turn off voice over so google it

  • I changed my Apple ID, now I can't login to iCloud because it still has my old Apple ID and the password no longer works to log me in. How can I get back into iCloud so that I can switch off Find my iPhone so I can make these changes? Thank you.

    I changed my Apple ID, now I can't login to iCloud because it still has my old Apple ID and the password no longer works to log me in. How can I get back into iCloud so that I can switch off Find my iPhone so I can make these changes? Thank you. (iPhone 4s)

    Well, you're gonna have to recover the password for that Apple ID:
    http://support.apple.com/kb/ht5787

  • How to turn off the voice over in Mac Pro

    I somehow turned on the voice over on my macpro, and it is repeating everything i am doing on my notebook. please help me to turn it off..

    You can turn it on/off via System Preferences, Universal Access (older OS) or Accessibility (newer OS).
    There will be also a keyboard shortcut for on/off toggle. Mine is command-F5.
    charlie

  • I Changed My Password on my ipad mini and now i cant remember what it is and i have tried many and it keeps disabling it for a while, how can i get back into it?

    I Changed My Passcode on my ipad mini and now i dont remember what i changed it to i have tried a few and now it is disabled for 1 hour and i dont know what to do or how to get back into it, Can Someone Help me?

    See here: http://support.apple.com/kb/HT1212

  • Just finished using iTunes, closed out and then tried to get back in.  Got this message "he iTunes library .itl file is locked, on a locked disk, or you do not have write permission for this file."  How can I get back into iTunes ?

    I just finished using iTunes, closed out and then tried to get ack in.  Got this message "The iTunes library .9tl file is locked, on a locked disk, or you do not have write permission for this file."   How can I get back ino iTunes ?

    I actually figured it out...I had to go to the iTunes Library Extras.itdb file and give myself permission to have full control.  THEN, I could go and estore a previos version.  Once I had done this, I got the same message for iTunes Library Genius.itdb . . . I did the same thing with it and Voila'!!
    Hope this helps...
    SVT

  • HT1212 I have a disabled Ipad 2 and have tried to reset so that I can get back into my Ipad.  What should I do?

    I have a disabled Ipad 2 and have tried to reset so that I can get back into my Ipad but nothing is working.  What should I do?

    Did you follow the directions in the article you linked from?
    http://support.apple.com/kb/HT1212

  • I am trying to turn off the Voice Over and can not scroll the IPAD to the accessibility tab

    I am not sure how but the Voice Over on my IPAD came on.  I have read that if I go to the settings, General, Acessibility I should be able to turn it off.  I am unable to scroll the touch screen to the Acessibllity tab.  thanks

    Connect your iPad to iTunes on your computer.
    Under the Summary tab for your iPad sync preferences with iTunes, at the bottom select Configure Universal Access. Turn it off there and select OK.

  • I locked myself out of my ipod and i have no way of getting back into it. any way i can reset it from my computer?

    i locked myself out of my ipod because i forgot my password. any way of me reseting it from my computer? its not my personal compouter that i have my own itunes on though. HELP!

    Since you will not be using your syncing computer,
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    You can redownload iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • HT2529 This morning Voice Over started running on my computer, but when I go to SYSTEM PREFERENCES/INTERNATIONAL ACCESS the Voice Over option is off, so I turned it on and then off, but it's still on.  What else can I do to make it stop?

    This morning Voice Over started running on my computer when I turned it on.  I did not turn Voice Over.  Could I have hit a combination of keys on the keyboard that accidentally turned it on?  When I went to System Preferences and chose Internation Access it showed that Voice Over was not even on.  I turned it on and turned it off to reset it, and it is still running.  How is this possible, and how to I get rid of it?
    Trumpeter

    I went to System Preferences, Universal Access, and then VoiceOver for the fiftieth time after you said to check VoiceOver Utility to see if I saw anything odd.  On The VoiceOver screen it was actually saying that VoiceOver was on.  All day the VoiceOver option was off, and the computer talked to me everytime I logged in.  I tried turning it on and off and it still talked to me.  Now the VoiceOver option was on, so I turned it off again. Weird! I had tried several combinations of keys again and again as the tech instructed me to do, but we couldn't turn it off, but I have to admit that after my phone went dead I tried everything I could imagine; so maybe in trying to turn the talking off I turned the VoiceOver Option on. Anyway, somewhere along the way it quite talking to me.
    Let me ask you a couple of questions.  When I clicked on VoiceOver Utility, after turning VoiceOver off, the screen message says: Speak the following greeting after login:  Welcome to Mac OSX.  VoiceOver is running. I was assuming that it meant VoiceOver was running.  That is what it is saying right now.   It's not talking to me anymore, but the screen says this whether the VoiceOver icon is on or off.  What is this all about.  Is it telling me that Voice Over is still running when I see this, or what?  After all, even when the OFF icon was chosen the computer still spoke to me when I hit each key upon logging in.  After you read the rest of this you will understand why I am asking if it is still running even though it's not talking to me.
    There is a box that appears and says "Portable Preferences for (Jane Doe) have been detected on (JaneDoe).  Would you like to use them?    Always Use   /  No  /   Yes      What does that mean?
    Last but not least. I was looking around and was clicking on Application, Documents, etc.  When I clicked on Documents, only four things came up even though there are tons of documents on my computer.  All four of them have to do with VoiceOver, and they were labeled as documents.  One of the documents had this in it:
    SCRConfiguration Cursor Tracking KBToVO
    SCRConfiguration Cursor Tracking VOToTXT
    SCRConfiguration Cursor Tracking VOToKB
    I'm not a computer genius, so maybe I just don't know what I'm looking at.  Is it normal for something like this to be found under documents?  All of these were dated today, and the problems started today. I haven't gone to bed yet, so even though it's after midnight it's still the same day to me.  Anyway, none of the documents were dated before this problem started.  On top of that, I have tons of documents on my computer, but when I clicked on Documents, those four are the only ones that showed up.  After trying to decipher the programming language on them, I went to click on Applications and hit Documents again, and all the documents came up.  I scanned the list and didn't see them, but there are so many documents on here that I haven't had time to slowly go over them to see if I missed those four documents somehow. Since then I haven't been able to get just those four to appear by themselves again.
    Now, is it possible that I still have a hacker and he knows through a key logger everything I am communicating to you and the Apple Store,  Maybe he did made a mistake and accidentally caused this problem, and through logging every key I have typed he has learned about his mistake and fixed it.  He could still be key logging me now without me knowing it; or maybe he removed the keylogger, because he know I'm taking it in to the Apple Store and can tell them now exactly what to look for.
    It is either a hacker, or I have a very vivid imagination.  What do you think? 

  • I was installoing ML and it came up, ' Install Failed' Mav HD damaged and cant be repaired. I now can't get back to my desktop. What do I do? Desparate!

    I was Installing ML and it came up, 'Install 'failed'. Mac HD is damaged and can't be repaired. I cannot get back to my desktop, this keeps coming up. What do I do, I'm desparate! Urgent.

    After you resetted your router you should try adjusting the wireless settings on your router...
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1
    Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    -Here select manual configuratioon...Wireless Network mode should be mixed...
    -Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on save settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.
    NOTE : Passphrase should be more that 8 characters...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation...
    Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...See if you get the desired speed...If not you should un-install and re-install the wireless adapter...

  • After opening Firefox & getting my info, I go into another application but am unable to open Firefox without Quitting it first. I have the latest update of Firefox. How can I get back into firefox without quitting Firefox?

    After opening Firefox, I was always able to in & out of it till I shut down my computer. Now, after opening Firefox, I go to another application then back to Firefox, I have to "Quit" Firefox and reopen. How can eliminate the back & forth of starting & quitting Firefox before I shutdown my computer?

    uninstalled firefox ....deleted all files still remaining under mozilla firefox directory in program files ... to avoid having to reprogram all my settings, reisntall all addons as well .. I did not remove anything from mozilla firefox that is stored in either appdata or under the windows users directory (if any)
    ... the as suggested reinstalled the latest version of the firefox browser using the link you provided in the email ..; tested and several issues still remain present and unresolved ....
    so please this is urgent or I will have to jump browsers and start using chrome .. because we work 14 hours a day 6 (sometimes 7) days a week, to get ready for the launch of our newest venture and we cannot lose that much days on browser related issues ... so please instead of putting me through week long step process .. of do this .. do that .. can you please actually look into the issue from your end .. I use firefox for so many, many years thta I deserve this kind of support .. thnx Robert

  • I have an email that is sent but won't disappear from my screen. I push cancel and nothing happens. I can't get back to my accounts. What do I do ?

    I have an email that won't disappear from my screen.
    I push cancel and nothing happens.
    I can see my accounts "behind" the email but I can't access them.
    I have turned machine off and on again.
    What else?

    Go back to your homescreen, then completely close down your mail app by double clicking the home button to open the multi-tasking bar. Hold your finger on the mail app icon and then click the red circle that appears on the left of the icon.
    Once you have done that, reopen the mail app and you should be sorted.

Maybe you are looking for

  • Macbook Pro Can't Run CRAP

    Hey guys!  Long time acount-less lurker, first time poster.   Go easy on me if I come off as long-winded or nubile, I made an account to post only because I know you guys are a strong, knowledgeable community! Here are my specs before I get into my p

  • A simple teststand applicatio​n passing object reference to C#

    Hi,  I have a  .NET application written in C# which has a UI with  NationalInstruments.TestStand.Interop.UI.Ax.AxExpressionEdit controls. This UI is invoked by a custom step in TestStand. One of the values, entered by user in the UI is a object refer

  • 4.0.3 Tab behavior a mess again...

    as an update to this post: http://discussions.apple.com/message.jspa?messageID=10181063 i had concluded that tabs worked as expected when i rebooted and restarted safari a few times. turns out this is not the case. the situation is weird, as it now h

  • Events in Drag and Drop application

    Hi, Events in  lifecycle of Drag and Drop application in ADF Edited by: [email protected] on Mar 2, 2009 6:57 AM

  • How to highlight All text in Control / Indicator?

    I need a  VI, that pressing a button I could select all text in control or indicator to be able to copy it then by pressing CTRL + C.  I tried playing with Property node with select-start, select-end, but no results. Also didn't find any documentatio