I have no "Performance mode" in my bios

MB 865G Neo2-LS v1.0
BIOS from 1.3 to 2.1
And i have no this option in bios setup.
Where is problem?

I Could be Wrong, But I am Almost Positive that you have to Run the Memory in "Dual-Channel" Configuration in order to Have this MAT Option Show up in the BIOS. So you Must get another Memory Module, and Place it in the DIMM Slot B-3, (That is if you have your Current Module in DIMM Slot A-1) So you should get More memory, As 256MB is really Not enough anyway, and with only 1 Module you Will Never see the Performance Increase to be Found while Running in Dual-Channel Mode................Sean REILLY875

Similar Messages

  • Satellite A210-16F - Can't go in sleep mode if I have performance mode

    On my Toshiba Satellite A210-16F small problem:
    When I have high performance mode on notebook it doesn't fall aspleep. But when I have Power saving mode then all is right. He fall aspleep. Do you know how is it behaves?
    Where is problem?

    Hmm it's strange. When I try to use sleep mode with performance mode but nothing happend (only screen changed to black but light and "Satellite" are still shinning).
    I check setting and Hybrid sleep mode is ON

  • IS THERE A 875p bios that will ALLOW PERFORMANCE MODE enabled in 5:4 setup

    if i run my pc3200 (400mhz) ram at 333mhz in the bios, performance mode doesnt work. no matter if it is on SLOW,TURBO,FAST,ULTRA, i get the  same perfomance marks in programs. cpuz might say its enabled...but it really not. my sandra scores stay the same. when running 1:1 my performance modes work perfectly. any bios version out there that will allow this?

    Isn't performance mode (PAT, MAT, HyperPath or whatever) tied to the 1:1 synchronous clock operation?
    Are we 100% certain that CPU-Z and Sandra are able to detect PAT/MAT/HyperPath mode properly?

  • B200 M3 memory stuck at 1333MHz in performance mode

    Hello,
    We have 2 B200 M3s in a new deployment running 2.0(3a). The B200s are configured with 64GB using 8GB DIMMs, using BANK 0 of each channel. We've deployed a BIOS policy specifying performance mode for LV DDR, and confirmed this setting took effect within the BIOS, yet the memory continues to run at 1333MHz. When looking at the server inventory, the DIMMs are reported as dual rank 8GB 1600MHz DIMMs. We've tried forcing the DIMMs to low-voltage mode and back to performance mode to no avail.
    In other UCS environments, we've deployed these same blades with the same memory configuration and BIOS policy and had no issues getting the RAM to run full speed. We're not using any kind of power capping either.
    Thoughts?

    Hi Brad,
    What CPU is being used?  3 of the supported CPU's for the B200-M3 do not support 1600 Mhz:
    http://www.cisco.com/en/US/docs/unified_computing/ucs/hw/chassis/install/B200M3.html#wp1028500
    Mike

  • K8N Neo - High Performance Mode Killed System?

    I'm slightly frazzled at the moment, so forgive me for any mistakes. I installed the K8N Neo Platinum on Tuesday night, with a brand new Athlon64 3200+ with 1mb L2.
    Video Card: VisionTek Xtasy Geforce4 Ti4400
    Memory: 2x Kingston 512MB 400MHz DDR PC3200
    Power Supply: Antec True550
    +3.3V @ 32A
    +5V @ 40A
    +12V @ 24A
    I installed the various MSI applications tonight, including CoreCenter. Attempted to adjust the FSB with it, but with just a 2.5% increase, the temperature of the CPU was getting higher than I cared to see during stressful applications. So I set it back to default, and later on read up on the BIOS settings in the manual... I read the description of "High Performance Mode", and figured I would try setting it to Optimized.
    Seemed like a good idea, let the board I had read was great for overclocking do it's stuff automatically. So after I set it to optimized (Didn't change anything else), I hit F10 and let it reboot. It never did. When it rebooted, the power stayed on, Hard Drive light showed it was being accessed... Only problem was absolutely no video was being sent. Monitor was as black as black could be.
    Turned the power off, tried again and again. Same deal. Power comes on, HD shows it is being accessed constantly for about 20 seconds, then just stops. But no video is being output, which leads me to think the system is just dead in the water for the most part.
    During this state, the LED's on the back are as follows: Top two are red, bottom two are green. I saw in another thread someone was going on about there being an explanation for them, but I don't have it in my manual nor could I find an explanation of them.
    At this point I'm just shaking my head, because there is absolutely nothing to be done as far as I can tell. If anyone has any ideas as to a possible solution or at the very least, whether the MB just went nuts or something worse happened, I'd greatly appreciate it. I'm at a loss and afraid to even think what might be the problem.

    While the "high performance settings" can surely make the pc unstable, it should hardly ccause hardware-damage.
    Turn the computer off (to be safe, remove the power-cord)
    Clear cmos with the jumper (instructions can be found in your manual)
    Wait 30 seconds
    Put the jumper back to its original position.
    Power on the system, and see if it works ?
    EDIT: Info from manual:
    Quote
    Clear CMOS Jumper: JBAT1
    There is a CMOS RAM on board that has a power supply from external battery
    to keep the system configuration data. With the CMOS RAM, the system can automatically
    boot OS every time it is turned on. If you want to clear the system configuration,
    use the JBAT1 (Clear CMOS Jumper ) to clear data. Follow the instructions below to
    clear the data:
    MSI Reminds You...
    You can clear CMOS by shorting 2-3 pin while the system is off.
    Then return to 1-2 pin position. Avoid clearing the CMOS while the
    system is on; it will damage the mainboard.

  • No Boot with Performance Mode FAST

    When I set Performance Mode other than SLOW (no matter if FAST or TURBO) my system won´t boot (all other settings default, D.O.C. DISABLED).
    This happened with Bios v1.9 and also happens with Bios v1.7 (re-installed hoping it might solve the problem)
    NO way activating MAT/PAT  
    Any help very appreciated  
    System:
    MSI 865PE Neo2-FIS2R (MS-6728)
    Intel P4 3.0 GHz FSB800 HT (default)
    Zalman CNPS 7000A-CU
    2x 512 MB Twinmos Winbond DDR400 CL 2.5
    MSI GF4Ti4200 (MS-8870)
    Samsung SP1614N 160GB 7200rpm 8MB
    Soundblaster Audigy 2 ZS
    Pinnacle DC10+ v7 Videocard
    LG GSA-4040B
    LG DRD-8120B
    Tagan TG-380-U1 380W
    Windows XP HomeEdition SP-1

    This might be a long shot...but try the following settings if you want PAT/MAT:
    Bios 1.9 for 865pe
    FSB=201
    Vddr=2.70V, or higher if it doesn't work
    Memory freq= AUTO (If you set it to 400 mhz you won't get MAT)
    Performance Mode= TURBO (FAST increases AGP/PCI bus)
    Timings= depends on you ram, set it manually to whatever specifications you have (If it still doesn't work, try setting to SPD)
    If all of this doesn't work then set memory freq to 400Mhz and Performance mode Turbo, or Ultra Turbo and you WILL get higher performance even if you don't have PAT/MAT. Test this with Sandra and you will see that the memory bandwidth is almost as high as with PAT on.
    Recommended: Install ClockGen and set it so that it loads with windows. Use it to set the FSB to 200 and AGP/PCI 66/33 for added stability.
    Please post back to see if this works for you guys. Good luck!

  • Screen freezes, even in safe mode and in BIOS

    I’m working on a friend’s laptop: Toshiba, Satellite M65 - S9092
    Original problem: The laptop started shutting down after few minutes of use. (Probable overheating)
    Took the laptop apart and clean it out. The heatsink, fan and outlets were really plugged up. Put it back together and did a clean re-install, Windows XP. Had few issues with USB drivers not being recognized but worked it out. Ran stress test for a whole day, no problem.
    Worked for few days and then USB wasn’t being recognized again and the screen started freezing up. Re-installed os again but it is still freezing up after few minutes, and stays that way till hard shut down.
    Screen freezes even in safe mode and in BIOS. (No blue screens)
    Switched existing RAM’s around (2 - 512MB), one stick, two sticks, etc…still freezing up. Wanted to upgrade the BIOS but can’t get pass the screen freezing. Not sure if the motherboard may be shot from previous overheating or need new RAM. Don’t want to spend money till I’m sure I’m replacing the right part.
    Any assistance is appreciated.

    Hi there... I have a satellite A70 - S256 an it was freezing up the same way. I downloaded an OS named UBUNTU fron the internet free of charge. once you download it an burn it to cd you can then boot from it after a couple of tries ( due to freezing). When it boots select your language immediately and choose the option to run memory tests (both installed and BIOS) and let it do its thing for as long as it takes. you should boot from UBUNTU on another working pc to get familiar with it if you are not allready so that you make your selection quickly before it freezes.  You may have to reboot a few times depending on freezing while the memory test is in progress and how much progress is made. This procedure fixed mines and I never had those problems again.    

  • Real-time apply in Maximum Performance Mode Not Working

    We have configured physical standby database in maximum performance mode. It's working perfectly fine. Archive logs are being applied to the physical standby.
    We can open the DB in read-only mode, but real-time apply is not working. Physical standby database is lagging behind the primary db by an archive log. As soon as primary database generates an archive log, it's transported over to the standby and applied immediately by the media recovery process. But real-time redo is not working. Standby redo logs have been configured.
    On Physcial Standby:
    SQL> alter database recover managed standby database using current logfile disconnect ;
    Database Altered.
    SQL> select group#, DBID, status,first_time, last_time from v$standby_log ;
    GROUP# DBID STATUS FIRST_TIM LAST_TIME
    4 UNASSIGNED UNASSIGNED
    5 UNASSIGNED UNASSIGNED
    6 UNASSIGNED UNASSIGNED
    7 UNASSIGNED UNASSIGNED
    SQL> select * from v$dataguard_stats ;
    NAME
    VALUE
    UNIT TIME_COMPUTED
    apply lag
    +00 00:31:36
    day(2) to second(0) interval 22-JUN-2010 08:42:06
    transport lag
    +00 00:31:34
    day(2) to second(0) interval 22-JUN-2010 08:42:06
    As you could see from the output above, value of transport and apply lag is equal to the elapsed time since last archive log switch.
    ********* Standby init.ora
    db_name = CPRD
    db_unique_name = CPRDS
    instance_name = CPRD
    service_names = hrDBSBY.WORLD
    log_archive_format = CPRD%r%s.%t
    log_archive_dest_1 = "location=f:\orarch\hresysprod"
    log_archive_dest_2='service=hresysprod async db_unique_name=cprd valid_for=(primary_role,online_logfile)'
    log_archive_config='dg_config=(cprd,cprds)'
    fal_server=hresysprod
    fal_client=hresysprods
    standby_file_management=auto
    log_archive_trace=1
    log_file_name_convert = ('hresysprod','hresysprods')
    db_file_name_convert = ('hresysprod','hresysprods')
    remote_login_passwordfile = exclusive
    ******* Primary init.ora
    log_archive_config='dg_config=(cprd,cprds)'
    fal_server=hresysprods
    fal_client=hresysprod
    standby_file_management=auto
    log_archive_format = CPRD%r%s.%t
    log_archive_dest_1 = "location=f:\orarch\hrESYSPROD"
    log_archive_dest_2='service=hresysprods async db_unique_name=cprds valid_for=(primary_role,online_logfile)'
    log_archive_trace=1
    remote_login_passwordfile = exclusive
    Please advise.
    Thanks,
    jay

    Hi,
    In your case you are using ARC process for redo transfer as you have not specified any process in log_archive_dest_2 and default is arch.
    I will suggest you to use LGWR to transfer the redo to standby and also check the size of standby redo logs on standby is same to the size of online redo logs on primary
    Regards
    Anudeep

  • Switchable Graphics Mode in the BIOS is not listed(seen)

    Hi everyone!
    I've read that:
    NOTE: If you do not see Switchable Graphics Mode in the BIOS or it cannot be selected, see the following section Updating the BIOS to enable Fixed Mode .
    However,  I didn't see that switachable craphics mode is seen in my BIOS:
    Product Name: HP Pavilion dv6-6093ex
    Product Number : LM610EA#A2N
    Version of BIOS is: F.05.
    Vendor of BIOS is: Insyde
    Also, I would say that my BOIS is not a UEFI BIOS because I cannot navigate the menus with a mouse but only just with the keyboard.
    However, I really was told that I shouldn't update the BIOS unless I am having a problem with it.
    Thus, I am afraid that if I had updated it, I would be encountring some problems not loading my machine well. However, I really want to know how to switch to external or internal adapter, thus I read here:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02948560#fixeddl

    Please see OpenGL Applications Cannot Use Discrete GPU with Intel + AMD Switchable Graphics for the basic procedure to update the BIOS and change the BIOS setting.
    HP Notebook System BIOS Update (Intel Processors) (SP54024) F.1A REV: A or later
    HP Notebook System BIOS Update (Intel Processors) (sp55068) F.1B
    and
    AMD High-Definition Graphics Driver (SP53025) 8.830.6.2000 or later
    AMD High-Definition Graphics Driver (sp55092) 8.882.2.3000
    If you have any further questions, please don't hesitate to ask.
    Please click the White KUDOS "Thumbs Up" to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • HT5147 Can't see my track displays during performance mode. Help!

    I have two loops for a music set I'm playing. When Mainstage is in Performance mode I can't see the track titles. It plays but can't see anything. Is there a way to turn on the track display in performance mode?

    Hi
    Sounds like you have not mapped Screen Controls (waveform display, parameter display etc) to the current patch (or set) Loopback (or Playback) plugs?
    CCT

  • Modded 7970 lightning bios

    are there any modded 7970 ltg bios about or can one be done??? after a touch more voltage.
    And is there an msi rep on these forums???

    Quote
    And is there an msi rep on these forums???
    Forum is user to user. Have you also looked for possible information in the VGA Section (MSI Graphics Cards) of the forum?

  • For Performance Mode

    HI ALL
    I HAVE SOME PROBLEM WITH PERFORMANCE MODE.MY COMPUTER DETAILS AS BELOW
    CPU:2.6GZ HT ENABLED
    RAM:2X256 KINGSTON KVR400X64C3/256 3-4-4 CL3
    HDD:40GB SEAGATE BARRACUDA ATA IV
    WINFAST FX5200 128 MB GRAPHIC CARD
    CREATIVE 5.1 DIGITAL SOUND CARD
    350W POWER SUPPLY(I DONT KNOW FULL DETAIL BUT I THINK POWER WORKING FINE )
    OTHER THINGS I THINK NOT IMPORTANT
    I AM WORKING PERFORMANCE MODE "SLOW".COMPUTER WORKING STABLE.
    AND IN SISOFTSANDRA MEMORY BENCHMARK IS:4220/4230
    BUT I TRIED TURBO MODE  MEMORY BENCHMARK IS:4700/4725
    BUT COMPUTER WORKED UNSTABLE.IM TRYING ULTRA-TURBO MODE BUT COPMPUTER IS NOT WORKING .I DONT HAVE ENOUGH INFORMATION ABOUT DDRAM TIMING AND SOMETHING LIKE THIS.WHAT CAN I DO ABOUT ULTRA-TURBO MODE .I WANT TO WORK ULTRA TURBO AND ALSO STABLE.
    I DONT KNOW WHAT CAN I DO.I THINK THIS ULTRA TURBO MODE FOR ONLY BEST RAMS LIKE HYPERX.CAN ANYBODY HELP ME ABOUT THIS MATTER.
     THANKS & BST RGDS

    To hit then highest overclock with your componets, I believe you want to do the following:
    Leave your ram settings at their SPD (Default)
    Have DOT turned OFF.
    Set your RAM voltage to at least 2.7.
    Set your performance mode to either turbo or ultra turbo.
    Lock your PCI/AGP Buses at 33/66 (or 34/67)
    Thereafter, incrementally increase your FSB. Once the rig becomes unstable, back off  until it becomes stable again and leave your settings there.
    I suspect that either your RAM or your PSU will be the limiting factor.
    By the way—Riddick rules all.
    Edit: Mods-- I do not mean to be presumptuous, but shouldn't the filter work only on whole words, rather than internal fragments? I.e. R-i-d-d-i-c-k (without the hyphens) was displayed as Rid****. I know the filters are necessary, &c, but that's a proper noun for the love of god. Sorry, I have a pet peeve about such things.

  • Acpi-cpufreq, pm-suspend, CPU1 set to high performance mode

    Basically, the background of the problem is that ACPI is unable to set my second core, CPU1, to the proper frequency. it gets some sort of AE_NOT_FOUND error or something in a psyloop. subsequently, the cpu0 is set by cpufreq while the second CPU, since it is not controlled by kernel at all, ends up overriding the CPU0 settings and setting the entire thing to High Performance mode. the acpi-cpufreq module then crashes and is unable to set any rules, so it defaults to 2.2 ghz and performance mode.
    I found that the only way to undo this after a resume from pm-suspend without restarting altogether is to first unload the acpi-cpufreq module (force option must be used otehrwise a "currently in use" error occurs), then reload it, then restart cpufreq daemon to make it restore the settings i have.
    $> sudo rmmod -f acpi-cpufreq
    $> sudo modprobe acpi-cpufreq
    $> sudo /etc/rc.d/cpufreq restart
    my question is, is there any way to REload the module and restart the daemon after resuming? i know that you can set acpi-cpufreq to unload on suspend, but that doesnt work because of the acpi-cpufreq module being used by another program, and i do not know how to make it forcibly unload. nor am i sure if unloading it would require me to restart the daemon still or not.
    your help/suggestions are appreciated
    -shrimants

    take a look at the wiki arch wiki pm-utils
    and create your own hook like this one:
    #!/bin/bash
    case $1 in
    hibernate)
    echo "Hey guy, we are going to suspend to disk!"
    suspend)
    /etc/rc.d/cpufreq stop
    rmmod -f acpi-cpufreq
    thaw)
    echo "oh, suspend to disk is over, we are resuming..."
    resume)
    modprobe acpi-cpufreq
    /etc/rc.d/cpufreq start
    *) echo "somebody is calling me totally wrong."
    esac
    bye iggy

  • Excessive Fan Activity - High Performance Mode

    I have a macbook pro 15" 2009 model
    It works brilliantly, no complaints I love it.. in battery saving mode!
    When its in high performance mode the fan goes nuts!?
    I've checked activity monitor etc and nothing is using all the power, theres no reason why the fan should be working harder than it does in battery saving mode.
    I always have open.. Adobe Fireworks, Chrome and Finder.. Thats pretty much it. And in battery saving mode everything works great, the fan is quiet. Why when I select high performance for a bit extra speed maybe does the fan speed increase tenfold? Dosnt make sense!
    Anybody come across this?
    Thanks

    Reset the SMC, as per > Resetting the System Management Controller
    1. Shut down the computer.
    2. Unplug the computer's power cord.
    3. Wait fifteen seconds.
    4. Attach the computer's power cord.
    5. Wait five seconds, then press the power button to turn on the computer.

  • How to Apply adjustment layers to multiple layers that have different blending modes ...

    How to Apply adjustment layers to multiple layers that have different blending modes  and keep the colours the same as the adjusment done?
    I work in Animation painting Backgrounds.  My files are sometimes upwards to 200+ layers.
    I will use adjustment layers to quickly balance colours and constrast on top of those many many layers.
    The only way that I know of how to apply adjustment layers it to every single layer  ( by applying I mean I need to get rid of the adjustment layers because we cant use them in production but i need the new colours be applied to all layers underneath ) in a psd is to manually do it By duplicating the adjusment layer 200+ times and  then merging each layer to one of those adjustment layers so that that layer can take the adjustment layers effect permanently.
    The issue is that Within Those 200 layers I have some layers set to Multiply or OVERLAY.    IT obviously wont apply the adjustment layer properly to those layers because those layer blend mode affect the layers under them. The colour wont be the same anymore in the spots that had the multiply blended mode.
    HEres an example of a simple File.  to show what i mean.
    https://dl.dropboxusercontent.com/u/3408266/ball%20layers.jpg
    https://dl.dropboxusercontent.com/u/3408266/ball.psd
    I have 2 adjustment layers up top.  I need to get rid of them by applying them to each layer! I cannot merge any of the layers. We need all those layers for production.
    I can apply the adjustment layers manually and this works GREAT for all Layers set to normal.  THey take on the colour change just FINE.
    However, The issue is that layer 6 and layer 4 are both set to mutiply and this screws up the colour once i apply the adjustment layers to each layer manually...
    How can i apply my adjustment layers to a file like this with some layers being set to multiply while keeping the layers exactly the same configuration  and The new colour taking efffect exactly how i looks before i apply the adjustment layers?
    Now the simple solution is to merge the multiply layers to the layer that it affects HOWEVER I NEED those multiply layers to be seperate! 
    I'm assuming what I want to do is impossible? Hope this isnt confusing.  As far as i know its impossible to do what I want it to do.  but just wanted to ask and see.
    I would REALLY REALLY love to talk to a adobe programmer/ technician/pro working at adobe about this.  Theres just no way to get in touch with anyone... =(
    any thoughts ?

    Sure... if you want to put it that way. Either way its not the desirable outcome. 
    its just frustrating that theres no way to apply adjustment layers to hundreds of layers while keeping them in the same configuration ( blendmodes,  layer order ,  without merging)  while keeping the same end result.
    works great if all your layers are set to normal though..    But I really need to keep shadow layers seperately and be able to adjust on the fly aswell as apply those adjusment to all my layers.
    I suppose that just isnt possible.   I understand the math required for this would be tremendous/ complicated if something like this would ever be implemented.  Would be nice if adobe could come up with some solution to this.  Its really a huge issue in my work flow and theres no alternatives.    How else can I adjust colours to 100+ layers  with a few clicks that lets me play around the the adjustment until im happy with the outcome.    Really wish i could adjust and the quickly apply that adjustment to all my layers regardless of blend mode.   LIke If the Layers with blendmode could somehow take the properties of the adjustment layer and keep adjusting those layers undereathe on top of that blended mode that its doing...   

Maybe you are looking for