I have problems with pci-gpib card under windows me, What I need to know what to do in order to fix this problems?
Hi, I have installed a pci-gpib card in my computer, I have a problem with
installation, the message of troubleshooting wizard is as follow:
"One or more missing GPIB interfaces.
There are several reasons why you might encounter this problem:
Reason: Your GPIB interface is incorrectly installed.
Solution: Please verify that your GPIB interface is correctly installed
and rerun the NI-488.2 Troubleshooting Wizard.
Reason: You are using a non-Plug-and-Play interface (e.g., AT-GPIB/TNT,
GPIB-PCII/IIA, GPIB-ENET) and you did not use the Add New Hardware Wizard
to add the interface to your system properly.
Solution: Click th
e Add Hardware button and the Add GPIB Hardware wizard
will guide you through the process of adding GPIB hardware.
Reason: For the GPIB-USB and GPIB-1394, the host controller (USB or 1394)
must be working properly in order to use the GPIB interface.
Solution: Click on the System Details button for details about the USB and
1394 host controllers.
Reason: For the PCMCIA-GPIB and PCMCIA-GPIB+, the PCMCIA host controller
must be working properly in order to use the GPIB interface.
Solution: Use the Windows Device Manager to verify that your PCMCIA host
controller is functioning correctly. Start the control panel by selecting
"Start>>Settings>>Control Panel", open the System icon and select the
Device Manager page. If you select "View devices by type", you can look at
the PCMCIA socket properties to ensure it is correctly enabled."
And on system details the message is the next:
"USB Driver type: USB universal host controller"
"This version of windows does not su
pport IEEE 1394."
I am using Windows Me, so i want to know what i need to do to fix this
problems.
Best regards.
If you have a PCI-GPIB card, you needn't worry about the USB port or whether or not Windows ME supports 1394. All you need in NI-488.2 version 1.70 from National Instruments. Install this driver and then insert your card. Windows should detect the card and find the proper driver.
If this did not happen in the proper sequence, look in the device manager and see if the card was installed as an "other device". If this happens, remove the card in the device manager and have windows redetect it. If this is not a solution, you may consider the ask an engineer page at www.ni.com/ask. Provide as many details as possible.
Similar Messages
-
Hi, I have a problem with fonts because in the window I can't see the font, they are transparent. how can I fix this?
giadad,
It sounds as this issue:
Open System Preferences and go to Accessibility. Next, select Display from the source list along the left, then check the box labelled Reduce transparency.
It was first presented in this post #15 by TheUlser:
https://forums.adobe.com/message/6854594#6854594
It has been described on this Adobe page:
http://capitalmacservice.com/font-preview-working-illustrator-cs-5-yosemite-fix/ -
Problems with pci--gpib-300k from computerboards
hallo,
i have problems with my gpib-card, win95 and 2000 identify this card
corectly but labview not, the max 2.0 find not cards.......have everyone the
self card and can help????
(sorry for my bad english..)
bye & thanks...
ThomasThomas,
The short answer is the MAX will not recognize non-NI devices. NI-MAX was designed to recognize and interface with National Instruments' boards such as our PCI-GPIB, AT-GPIB/TNT, etc. With the introduction of MAX2.0 and NI-VISA2.5, there was an added capability to recognize some Hewlett-Packard boards but even then, configuration of them must be done from an HP interface.
LabVIEW will interface with the board fine but MAX is designed specifically to interface with our drivers for our boards.
Ryan Mosley
National Instruments, Applications Engineer
http://www.ni.com/exchange -
On a MAC G4, WITH OS 10.5.8, I DOWNLOADED 3.6.8, BUT I CANNOT INSTALL IT. IT SAYS I DO NOT HAVE SUFFICENT PRIVILEGES. WELL, IT'S MY COMPUTER AND I AM THE ADMINISTRATOR ON IT. HOW DO I FIX THIS PROBLEM SO I CAN INSTALL FIREFOX 3.6.8??
== I DOWNLOADED UPDATE 3.6.8Snow Leopard = OS X 10.6.x
It is Not available as a download... It is a Paid Upgrade.
Do this first...
Check that your Mac meets the System Requirements for Snow Leopard...
Snow Leopard Tech Specs
http://support.apple.com/kb/SP575
If so... Purchase a Snow Leopard Install Disc...
http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
Other countries...
http://support.apple.com/kb/HE57
After the Successful Install, run Software Update to get the latest updates for Snow Leopard.
Be sure to make a Backup of your Current System Before Upgrading... -
I'm having problems with videos, they shake and the images break up back and forth into striped colors, how do I fix this?
1) This is because of software version 1.1. See this
thread for some options as to how to go back to 1.0,
which will correct the problem...
http://discussions.apple.com/thread.jspa?threadID=3754
59&tstart=0
2) This tends to happen after videos. Give the iPod a
minute or two to readjust. It should now be more
accurate.
3) This?
iPod shows a folder icon with exclamation
point
4) Restore the iPod
5) Try these...
iPod Only Shows An Apple Logo and Will Not Start
Up
iPod Only Shows An Apple Logo
I think 3,4, and 5 are related. Try the options I
posted for each one.
btabz
I just noticed that one of the restore methods you posted was to put it into Disk Mode First rather than just use the resstore straight off, I Have tried that and seems to have solved the problem, If it has thank you. previously I have only tried just restoring it skipping this extra step. Hope my iPod stays healthy, if it doesnt its a warrenty job me thinks any way thanks again -
Computer won't boot with PCI-GPIB card installed
I'm running a windows XP system with Labview 7.1 installed. I have installed the GPIB drivers, but when I insert my PCI-GPIB card, the computer will not boot(it freezes before the POST). I'm running a Shuttle "MK40VN" KM400 Chipset Motherboard.
Well, nevermind, I just verified that the card is in fact fried.
-
As mentioned above I have just downloaded OSX Maverick to my iMac. I am now having a lot of problems with iCloud. I get the message that "This iMac can't connect to iCloud because of a problem with, and then it goes on to quote my e-mail address. It then says to open iCloud preferences to fix this problem.
I do this and no matter what I seem to do this message continues to return.
Can anybody explain how to resolve this problem (please bear in mind that I am noy very computer literate).
Many thanks
MikeHello John
Sorry I haven't got back to you sooner.
Thanks very much for your help, your solution solved my problem.
Thanks again and kind regards
Mike -
When I sync my devices its starts to sync then it says "canceling sync" how do I fix this problem?, I am running iOS7 on my devices and the newest version of iTunes on my MacBook Pro with Mavericks.
The first thing that I always do when I have issues syncing is quit iTunes, restart my Mac and reboot my device.
Reboot your device by holding down on the sleep and power buttons at the same time for about 10 seconds until the Apple logo appears on the screen and then let go of the buttons. -
It is any problem with the application vtok? Since I update my iPad2 system to iOS6.0 I was unable to use this application. The problem is when I tap on the vtok icon, the application opens and closes right away. I removed and reinstall the application twice, but this doesn't fix the problem. When I try to find the application on application store, it's give me a message that the vtok application is not available in USA.
Not available in Spain either. I can't find anything googling for this problem, Vtok's page and facebook page seem to be unmaintained.
It is strange such a widely used app doesn't show life signals.
Good luck -
Problems with PCMCIA-GPIB card
Hi all
I am using a PCMCIA-GPIB with driver version 2.2 on a Windows XP with a PCI-to-PCMCIA Adapter from Ricoh (device manager says: Ricoh R/RL/RT/RC/5C475II,R5C520 or compatible cardbus controller).
The Win XP detects the card without any problems and there are no resource conflicts.
However, I cannot communicate with GPIB devices and the NI-488.2 Troubleshooting Wizard says:
1. NI-488.2 Software Presence = verified
2. GPIB Hardware Presence =
And then a new screen: "The trouble shooting wizard has detect that no GPIB interfaces are configured on your system"
Can someone help me? There are no resource conflicts and I have also tried changing the PCI slot. The same problem also occurred when I installed the card in an
other computer.
Regards,
Juan"I have tested a RICOH PCMCIA to PCI Adapter card. The PCMCIA to PCI Adapter card was tested using different operating systems (Win2000,XP,98,95) and using a Micron computer PIII 650 processor. When testing under the XP environment, with service pack 1, NI's device drivers Version 1.7 failed to load. (Code 10) Ni's driver version 1.7 was then removed and NI's device driver Version 2.2 was loaded. I did not experience any commutation problem as long as I used the standard NI calls. I did experience a problem with NI’s IBDIAG function call which is not supported under Version 2.2.
I would recommend that you get the latest service pack for XP and NI’s device driver Version 2.2. -
How can I use the instrument toolbox in MATLAB 6.1 to contol the PCI-GPIB card under Linux?
I'm trying to use the PCI-GPIB controller to control lab equipment through MATLAB 6.1 (R12.1) under Linux. MATLAB's instrument toolbox seems to integrate with NI's board, but the MATLAB documentation says it requires the installation of a driver. I've downloaded the linux gpib driver, and I'm able to run the associated utilities (ibconf, ibic, ibsta), but MATLAB cannot interface to it. For example,
>> g=gpib('ni',0,1)
??? Error using ==> gpib/gpib
The specified VENDOR adaptor could not be found.
Where can I find a MATLAB driver and how can I install it?
Thanks,
RichardHello-
The knowledge base: "Can Matlab for Windows Call the National Instruments GPIB Driver?" Also applies to this question as well. This article is very extensive. Try searching on ni.com for "+matlab +gpib" for more details.
Randy Solomonson
Application Engineer
National Instruments -
Still problems with Toshiba Bluetooth Adapter under Windows 7
Hey there, it's me once again.
I refer to my thread "Bluetooth Problem under Windows 7":
I thought after the solution from bluecat my problem was solved. But it's not really.
After installing the Windows Hotfix, it worked just shortly. But now the problem is the same.
When I delete the Toshiba Bluetooth Stack and try to work with the Windows Bluetooth Manager, I see, that the Bluetooth icon is coming an going on the task bar. In device manager I said Windows, that it doesn't shut down the device to save energy. But I think the device is turned on and off and on and off...
I really have absolutely no idea what the problem is, but I am becoming terribly angry.
Details:
Windows 7
Dell Wireless Bluetooth Internal Adapter 350 (but it's made by Toshiba)
Drivers tried out: Vista Profile Pack from Dell Homepage (no stack installed, just driver) / Toshiba Bluetooth Stack (the latest version)
This is the old Thread:
Dear all
Just as I installed Windows 7, my Bluetooth mouse and keyboard don't work fine.
I use the Dell Wireless 350 Bluetooth Internal Adapter, Logitech MX1000 mouse and keyboard and Toshiba Bluetooth Stack 8.00.02.
To connect the devices with my Computer, I firstly must disconnect the Bluetooth adapter by pushing Fn + F2 on my Dell i9400, after re-connecting I can search and connect the devices correctly. They work fine as long as the notebook is running.
After rebooting the notebook, the devices don't work anymore. They are still listed in Bluetooth Stack as known, but not as connected. Therefore I have to disconnect the Bluetooth adapter another time and re-connect it to be able to connect the two devices.
I firstly thought, that it's a Windows problem. I thought that Windows is able to put down the adapter to save some energy. But when I go to the Device Manager, there is no box for this option as known from other devices (f.e. USB-Ports). So this is not the problem. I think the problem is something else, maybe done by the Bluetooth Stack.
Under Windows XP this all worked perfectly. I used the same hardware and also the Bluetooth Stack by Toshiba (downloaded on the Dell Homepage).
Anyone some ideas?
Thanks!
DaevuHey there
Yesterday I made Format C: and installed Windows 7 new.
I did not install any bluetooth driver for my Dell Wireless 350 Bluetooth Adapter (made by Toshiba).
And now: The mouse and the keyboard are working. I even do not see them anywhere in my system, but they are working.
There is no bluetooth adapter in my device manager and I had not to connect the mouse and the keyboard with my computer. It's simply working without doing anything.
I don't understand this...
Is this a save connection?
What I've tried already:
-> Installing newest Bluetooth Stack from Toshiba. Problem seen in the message above. I also installed the MS Hotfix. Same problem.
-> Installing "Vista Profile Pack" from Dell Homepage, recommended for my notebook and Windows Vista. There is no stack installed. So I had to connect the mouse and keyboard via Windows Bluetooth Manager. But the adapter was made on and off by windows, the icon in the taskbar came and went and came and went. Connection is 1 minute good, then some seconds away. Not possible to work with the mouse.
And now without installing any driver it's working. Am I stupid?
Daevu -
W510 problems with Nvidia driver recovery under Windows 7 (64 bit)?
Lenovo W510, Nvidia Qudardo FX 880M video, FHD:
What I'm seeing on occasion is a Windows 7 (64-bit) recovery, screen blanks out, goes 2-3 seconds, then recovers, things go back to normal, but a message displays saying that an error was detected in the video driver, and it has recovered. The new Firefox (4.0.1) seems to be one of the things that may be a contribution, hard to tell. Per System Update at least, I'm current on the Lenovo downloads. SIW shows the driver level as 8.17.12.5738 (2010-06-27). Nvidia web-site shows their current driver level on the wen-site as 270.61 (2011-04-18), which is a considerably newer date at least. So two questions:
Has anyone else seen Driver/Recovery issues on Win 7 (64)
Has anyone directly run the Nvidia video drivers and had them run OK?
Seems like it would be nice for Lenovo to update their drivers, if indeed this is a driver issue, they appear back-level.I used to have this problem with my W510 running Windows 7 Enterprise 64-bit, especially Firefox 4 crashing the Nvidia display driver almost constantly. I googled and found that this is a known problem between older Nvidia driver and Firefox 4. Later on I downloaded the latest version of Nvidia driver from Lenovo website (it was not posted on the System Update server yet but was available on the regular download site). I clean-installed it (i.e., removing all files and settings created by the old driver) and I haven't experienced the problem since then.
Twitter @thitiv | Work | ThinkPad W520 (4270-CTO) Core i7-2960XM 2.7/3.7 GHz | 16GB Kingston HyperX PnP DDR3-1866
2 x 256GB Crucial M4 & C300 SSDs | Intel Centrino Ultimate-N 6300 | Ericsson F5521gw WWAN | Ultrabay Blu-ray Burner
NVIDIA Quadro 2000M | 15.6" FHD 1920x1080 | ThinkPad Battery 55++ (9-cell) & Battery 27++ (9-cell slice) -
I recently updated my phone software to iOS 6.1.3 and for the first couple of weeks, it was ok. but then until monday, the option to turn on the wi-fi has been greyed out so I can't turn my phone's wi-fi on which means I have to keep using my 3G coverage which will eventually cost me a fortune if I don't get the wi-fi greyed out problem sorted out as soon as possible. If anybody could help me with this problem (without having to take it apart or putting it into the freezer) please let me know as soon as possible.
Thanks
alexmac92 xI have seen a few searches that indicate some people have had success by changing their wifi security settings. Using none (not recommended) or using WPA2 with a strong pass phrase (longer than 8 characters) seems to work for everyone I've talked to. I've not had this issue myself on any of my devices (2 iPhone 4, 2 iPhone 5, 2 iPad 2, all running iOS 6.1.3, and 2 iPod Touch 3rd Gen running iOS 5.1.1), but then again, my home wifi has had a strong pasphrase, and WPA2 for 7-8 years now. I beleive that some people have had luck with performing a reset of network settings (but others have not, and claimed that it actually made things worse some how). Some have had luck performing a device restore in iTunes, while others have claimed that did nothing but cause them to lose everything.
I know there is so much wifi congestion in my neighborhood that it is hard to find a channel that doesn't already have 2-3 routers using it. It is possible that resetting your wifi router might help. I know that when my iPhone wouldn't connect to my wireless network, it would usually clear up if I restarted the router. -
Today all my emails started coming and going out as Holidays in United States. I can't seem to be able to fix this. Anybody experiencing this? How do we fix it?
Hi Guys ,
I had the same issue , as some one suggested please check in your contact under your name .
If your name in contact list does not have email address it will come as 'Holidays in United states' (Which is so frustrating as I am working , LOL), you need to add your email address in your contact name and then it will go.
I have done that and it worked for me , best of luck
Maybe you are looking for
-
OS X Mountain Lion - Apple mail not displaying images
Ever since upgrading to OS X Mountain Lion a few weeks ago, Apple Mail no longer displays images in emails. I have downloaded and installed the latest Java RTE [it was out of date] - that didn't fix it. I have tried to reset my Java preferences to
-
I am attempting to delete xml files through the following command: delete from (select 1 from resource_view where UNDER_PATH(res, '/home/user1/forms', 1) = 1 order by depth(1) desc); /home/user1/forms contains over 200,000 schema-based xml documents
-
Hi, I am a newbie att SAP, and have a problem: I have a Web Dynpro application, and a third party application. I want the Web Dynpro application to post large amounts of data to the other application, which in turn posts data back to webdynpro. I am
-
Keynote's themes come with some nice custom bullets, which I would like to appropriate to use on slides not with those themes. There is a "custom image" chooser in the Bullets inspector, but I cannot find where the stock custom bullet images reside o
-
I have an application that works fine using VOs but the more I think of it, I might entertain using an in-memory SQLite DB and when the user saves, commit it to a file. If I create the DB in-memory, is it relatively easy to change it to save to file