I have two Buildings i need to connect via wireless
I have one Building with The Main Internet Connection. It has 1- wireless-G access point (wap54g v3) and 1-wireless-B ethernet bridge (wet11 v2)
The other Structure i cant run wire cause of a water hazzard between the buildings. Building two has 1- Wireless-N Broadband Router(wrt300n)
With These 3 Products what can i do using what i have to connect, connect building 1 to building 2 via wireless? Or am i in need of another wireless router of sorts?
help and documentation would help. I just was dropped into this and had a day or two to fingure a solution out.
Thank you
The Computers which are connected to WRT300N on Building Two are they able to go online throught the Router? Then i would suggest you to get an Ethernet Bridge, As your ethernet bridge is older B series and it wont communicate with your Router properly, Either you can Get a G Series or N Series Ethernet Bridge ( WET54G , WET600N).
On Building 1 you need to input the wireless settings as you have set on your WRT300N Router. Once you configure all the settings on your Bridge, then you can connect the Bridge to an switch and then connect your Access Point to the Swtich and configure all the settings on your WAP54G. And this will let all your computers go online Wirelessly and Wired as well.
Similar Messages
-
I have two iPads and one is connected to the internet but my other iPad was connected then was not and since then I have not been able to add my internet back onto my iPad it only says cannot connect to the server any help would be great thanks
If you are having WiFi problems it is necessary to isolate whether the problem is with your network or your iPad. Note: Do NOT consider your network to be blameless if some other devices can connect to it.
First, test your iPad on some other WiFi networks: a friends, Starbucks, Barnes & Noble, etc.
If it works well there then the problem is probably with your network. Try restarting your WiFi router by removing power for 30 seconds. If that does not help check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
If your iPad does not function well on other networks it possibly has a hardware problem. You could try Settings > General > Reset > Reset Network Settings to see if that corrects the problem. If not, contact Apple Support or visit an Apple store for evaluation. They can provide a replacement if your iPad is bad.
If you need more help please give the make, model, and version of your WiFi router and how you have it configured. -
i am new to the ethernet communication using labview. I do not have any hardware. I have two laptop i need to send and recieve the data via these 2 laptop using labview. Kindly help me on this.
Solved!
Go to Solution.Hi thanks for the help.
Actually i am trying to send 10 sine signals from server pc to client pc. So i will bundle 10 signals in server pc and send it and in client pc i am unbundling it and need to save in TDMS format.
Till unbundling i was able to do. TDMS format it is saving only last value. I need to save all the values. Kindly help me on same. I am attaching both the VI.
Attachments:
Client.vi 62 KB
Server.vi 252 KB -
I need to connect my wireless printer (HP LaserJet CP1025nw color) to the internet.
I need to connect my wireless printer (HP LaserJet CP1025nw color) to the internet. I recently have changed my name and password of my modem. Since the change I have lost connectivity between my computer and my printer. What do I need to do to regain connectivity? I am using Windows 7.
TrydellI think you mean your password on your router right? Changed your SSID and/or password?
Try here.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired! -
I have a Canon LBP5360 laser printer connected via USB cable to my MacPro running 10.6.8
I have downloaded the latest UFR II driver. (UK Version)
I am trying to connect to the printer but the printer is not appearing in my Print/Fax Preferences.
When I click the box "More Printers" under the Default printer the drop down box gives me a heading "Canon IPv6 (UFRII) with the option to add or cancel. (The add is highlighted). But there are no printers showing in the box. Nothing. Can anyone help?
Is there a problem with my Mac setup or maybe a setting in my printer?Mac UFR II Printmonitor
UFR II Printmonitor is application software that interfaces with the software for the printer, and is installed with the printer driver. You can start UFR II Printmonitor in the following folder to check the printer status, and errors. Refer to the Help how to use the Print Monitor.
MF3010, MF8000 Series, MF8000C Series, MF8300 Series, MF8300C Series:
Print Monitor: [Library] - [Printers] - [Canon] - [CUPSCMFP] - [Utilities]
Other Printers:
Print Monitor: [Library] - [Printers] - [Canon] - [UFR2] - [Utilities] -
Questions: cannot connect via wireless laptop (router WR...
Questions:
cannot connect via wireless laptop (router WRK54G)
cannot secure my network using WEPfrom the wired computer , access the router using http://192.168.1.1 . the default password is admin
on the router ui , click on the "wireless" tab , change the ssid - any non-linksys name , channel - 11 , ssid broadcast - enabled
go to the "wireless security" subtab .. change the security mode to WEP - 64 bits , default transmit key - 1 , enter a 10 digit hexadecimal number in the WEP key 1 field , passphrase - empty
under the "advanced wireless settings" , change the beacon interval - 50 , Fragmentation threshold - 2304 , RTS threshold - 2307 -
Connecting via wireless & blue square?
hello
I'm connecting to the www via my router and when it's not possible to connect I seem to be connecting via a blue square on the toolbar ,anyway what is this and can it be switched off because I only want to connect via wireless router or hotspot
ThanksHey macbookair,
The Blue square means GPRS: http://docs.info.apple.com/article.html?artnum=306795
Try the Wi-Fi tips listed here: http://support.apple.com/kb/TS1398?viewlocale=en_US
Forgetting the network or resetting network settings will probably take care of it.
If the iPhone still cannot join the Wi-Fi network give us a little more information about the specific wireless router you are connecting to and the security being used. Also Include the number of characters in the network password.
Jason -
I have two Kindles. Can't connect either of them t...
I have plenty of devices connected to my HH2 (BT Infinity 2). iPad, iPod, mobile, laptops, ps3, all work perfectly. But my kindles won't connect.
These are two different models, a 3rd gen and the latest paperwhite. The 3rd gen was always connected via 3G, and I have no recollection of whether it ever connected to wifi or not - but today it will not. I bought the wifi-only paperwhite yesterday and it also won't connect to the home hub. It will connect to what I'm guessing is BT-FON, which shows up on the available networks as "BTWiFi". I enter my BTinternet.com address and password via the browser to access that, but the signal for that is very weak and keeps dropping out.
On both the paperwhite and 3rd gen, I try to connect to my wifi network "BTHomeHub2-LFFT" using the wireless key 41dj528ers (not real values). It tries to connect but then times out, saying "Your kindle is unable to connect to the wi-fi network[...]".
So far I've tried:
Completely shutting down and resetting the kindle and the router a number of times
entering everything right next to the router, with a full strength signal indicated on the kindle (still can't connect)
changing the home hub from b/g/n to b/g
changing from WPA2 to WPA (failed) and then to WEP (failed)
changing the band from automatic to 1, then 3, 6, 9 (all failed)
Anyone with any ideas?
Solved!
Go to Solution.I know this sounds obvious, and I'm sure you've checked, but many people err when entering their Wireless Key for the home hub onto a device.
Are you sure that you havent made an error with this?
Seems odd for two devices not to connect though
AQ.
"Welcome to Royston Vasey - You'll never leave." -
Same value in two or more different objects connected via session
I have to object class with get and set method configure in faces-config.xml as session
<managed-bean>
<managed-bean-name>user</managed-bean-name>
<managed-bean-class>com.dirsot.content.utility.RegisterUser</managed-bean-class>
<managed-bean-scope>session</managed-bean-scope>
</managed-bean>
<managed-bean>
<managed-bean-name>album</managed-bean-name>
<managed-bean-class>com.dirsot.content.tables.UserAlbum</managed-bean-class>
<managed-bean-scope>session</managed-bean-scope>
</managed-bean>
in both objects, RegisterUser and UserAlbum i have two identical attribute called us_email as user email.
I need them to be in both object because I'm using hibernate to store them in the database.
my question is when I logged in, RegisterUser get the value and sets us_email value from the user.
what can I do that the stored value on RegisterUser to be also reflected on UserAlbum? Obviously I cannot create new object inside RegisterUser because that will not show in the session.
is there anyone that can give me some indication.
code examples are really really welcome. Thank you.harddisk wrote:
what can I do that the stored value on RegisterUser to be also reflected on UserAlbum?Better inject the one bean in the other bean or just access the other bean through SessionMap.
You can find here useful code examples: [http://balusc.blogspot.com/2006/06/communication-in-jsf.html]. -
I have a canon printer mf5940dn, it is connected via USB to my macbook air, and yet, when I want to print smth, it says the printer is not connected. does anyone has any idea why? is there a guide to do it properly?
Hi,
I am currently replying to this as it shows in the iChat Community.
I have asked the Hosts to move it to Snow Leopard (you should not lose contact with it through any email links you get)
I also don't do Wirelss printing so I can't actaully help either.
10:01 PM Friday; July 29, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb( 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously -
Unable to connect via wireless, printer is online.
I am using a Photosmart plus 209a via wireless. There are 3 notebooks connected. 2 will print but my Dell Studio (Win 7 Pro) will not. It was previously connected but now unable to connect. I have uninstalled all components using level 3 twice. Have used the Print/Scan tool. Downloaded the full SW package and the Basic driver SW. I process a job and it gets to the spooler and then "print job failed". I can view the control panel via IP address. I can view network settings and print wireless test page through HP Solution Center. Why am I unable to connect? I was able to use via USB but this is not an option.
It sounds like there is something different on the Dell Studio since it works from two other computers on the same network as the Dell Studio. It also sounds like you are able to access the EWS of the printer by using its IP address.
Are there any other errors messages regarding the printer? If so, what are they?
Is there a third party firewall installed (e.g. Norton, Kasperksy, BitDefender, etc.)?
Is this Windows 7 Professional 32bit or 64bit?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓ -
EA3500 drops VPN connections via wireless
I don't have problems with the computer on other wireless connections with using VPN, so its not the laptop. If I am connecting just to the internet and not trying to connect to the VPN i don't have any issues. If I connect a CAT5 cable directly to the laptop I don't have any issues. If I try to connect via the wireless the VPN will connect and then drop, usually every 30 to 60 seconds. I have looked at the settings and can't see any that would make a difference. Any suggestions on what might be happening and what I need to change on the settings?
thanksMaybe the wireless connection is not enough to handle wireless VPN connection. Try adjusting the wireless settings to improve the signal. Change the wireless channel under the 2.4 GHz to 6, 9, 11, and 1. And use 161 or 157 for the 5 GHz band.
-
I have my new MX922 connected to my home network via wireless. When I attempt to scan photos I receive an error message stating that the scanning software was unable to communicate with the scanner. Code:5,157,69.
I have no issues when printing or faxing it is only the scanning function. I am using the Canon supplied software - My Image Garden - to do the scan.
Please advise.
Solved!
Go to Solution.Hi!
To ensure the most accurate information is provided, we will need to know the version of Windows or Mac in use.
If this is a time-sensitive matter, our US-based technical support team is standing by, ready to help 24/7 via Email at http://bit.ly/EmailCanon or by phone at 1-800-OK-CANON (1-800-652-2666) weekdays between 10 AM and 10 PM ET (7 AM to 7 PM PT).
Thanks and have a great day! -
Can't connect via wireless wrt160n ver 1
I am using a wrt160n version 1 with the latest firmware. The internet is via cable modem which works fine and the computer i am writing this message with is connected to the router via ethernet. The problem comes when i try to connect another PC (mine, this is my mum's) via wireless. I am using windows 7 and it says after 2-3 seconds Windows cannot connect to the wireless network. The signal strength is showing excellent with all bars full (and i have checked this by moving the router to within 10 cm of the wireless aerial of the computer that fails to connect and nothing changes). Occasionally it will connect, but the speed is awful and it wont reconnect when windows is restarted. I don't know why it connects occasionally. When i say occasionally i mean after 100 or so attempts, but this is no guarentee. I have tried multiple aerials including one with an insulated cord, so you can put the aerial far away from your computer, so i don't think theres a problem with interference.
I have tried:
resetting and reprogramming the router, including factory reset
re-aplying the latest firmware
deleting the connection profile in windows
resetting my computer and the network adapter (my wireless card)
3 other network cards
moving my computer, the router, the aerial
changing channel
formatting the computer that cant connect, fresh installing windows
cursing and praying.
In the network diagnostic details from windows 7 auto-repair thingy, it seems that pre-association is working, but actual association is failing. The error code given is "0x00038002" next to association. Further down it also says that it failed to recieve a response from the access point or router. The funny thing is, everything was working fine a few weeks ago with the exact same hardware and software. Nothing has changed except my ability to connect.Well I think (fingers crossed) mine is working properly now... so far so good.... i have a happy teanager again... she has internet.... ha-ha
Default reset on WRT
Firmware update to Version 3 on the WRT (that was a pain in the butt... )
default reset on WRT (AGAIN)
reconfig..../set-up .etc....
Had to adjust the settings on the firewall of the Win7 laptop to allow Cisco Pure networks and Network Magic to enter the wall...
As much as I didnt want to... I also installed Network Magic on both computers and it really walked/guided me through alot of the issues and fixed most of the items by itself... Saved info to USB and uploaded to Win7 laptop... and it is working fine now......
Lets see if it last and works smoothly.... -
Officejet pro 8500A connected via wireless, but not accessible....
I can t access my officejet pro printer via wifi, after a firmware upgrade last week. I can print however from my iPad, but not from my laptop. Both are connected to the same wireless signal. I can see in my printer and router that both are connected. When I connect the printer via a cable to the router, it works.
As said, I lost this after firmware update.
I tried:
Update the software on my laptop : no Improvement
Switch on/off the router, printer, laptop : no improvement....
Can anybody help? Would a downgrade offirmware help? Anybody familiar with this problem?
Laptop : W7-64The workgroup shouldn't matter. It's strange that the printer will communicate with the laptop as long as one of them is connected via Ethernet to the router. It shouldn't be doing that at all. It has to be something in the router. I know you mentioned using a different router and it worked just fine. Problem is I'm not sure why this router isn't working right. I'm sure the printer is out of warranty, which is why I'm sure you came to the forums first, but you may need to contact HP tech support. They should be able to remote in and find the setting that's blocking communication. II'll link the information to get in touch with them below. The link will take you to a form to fill out. Once you fill it out and it is processed, it will give you the printers warranty information, a case number, and the phone number to call.
HP Technical Support Case Call Form
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
Maybe you are looking for
-
Help! My system crashes very often and without any apparent reason.
Hello, I think I have the same problem as Juju had in a previous thread. My sistem has the following: Pentium 4 2.4GHz HT (800 MHz FSB), MSI 865PE Neo2-LS MB, 2 x 256MB DDR400 made by PQI, Nvidia GEForce 4 MX440 with 64MB RAM (Only AGP 4x),
-
Schedule line date vs actual delivery date
Hi All, Is there any standard report or work around available to compare customers schedule line date vs actual delivery date Thanks & Regards,
-
Can no longer access the files on my Zen Xtra. Help, plea
I've been using my 60gb zen xtra for over a year now without problems (except for having to replace it twice due to the faulty headphone jacks), but after recently losing one of my hard-dri'ves, I decided to install Creative Mediasource so that I cou
-
Report Query shows different result when executed manually
Hi! When I run our report I'll get 7577 distinct rows. From here on I copied the SQL query with SQL inspector, then pasted it in Oracle SQL Developer and replaced the user variable with the same value I entered when I ran the report from within Oracl
-
HD to rent, but not to buy
Why is it I can rent a movie in HD format, but I can't buy it in HD format?