I have vertical lines when printing even after changing cartridges.

I have vertical lines when printing even after changing cartridges. There are no lines when copying, faxing or scanning, only printing. I have cleaned the glass, scanner and even dusted where the toner cartride slides in.  Any suggestions?

Sorry but I have worked on laser printers for over 20 years and never encountered your issue.  That is of course if you are explaining it correctly.  When you make a copy to be printed or print a reports page from the printer or send a print job to the printer, if in all these cases you get the line, then yes the issue is either the toner cartridge or the fuser.  If you make a copy to be printed and it prints without the line (Put original in adf, press copy button and print should come out), then you have one weird unit since it does not make sense since the print formatter on the unit whether making a copy or printing from the computer or unit itself uses the same hardware.  Now to test if the printed copy has a line then just put a sheet of paper on top of the feed tray and do a self test from the printer.  When the back edge of the paper enters the printer, quickly open the toner door to stop the printing.  Remove the toner cartridge and look at the image below.  If the defect is present the toner cartridge is the issue and if the image below does not have the defect, then the fuser needs to be replaced.  Best I can do.  Good Luck.

Similar Messages

  • Hp photosmart 3210 all-in-one - some colors not printing even after changing cartridges.

     I recently had an issue while printing a document. the content was off colored and the error message said black was low. Changed the black cartridge and things just got worse from there. Still no black, cleaned the printheads, printed another test page and no longer had magenta or lt magenta. Replaced those as well. the only had yellow, magenta and lt. magenta.  yellow was low as well, so now every cartridge has been changes.Tried to print document again and it printed in magenta and lt magenta. never have seen black again and the self test diagnostic page is printing in purple. What should be black showed up as purple with lines and yellow is a rainbow of mustard, magentas and purples. no other colors show up. WHAT IS GOING ON? have tried several times to align the printer but it always fails. Have cleaned the printheads several time and just get a mish-mash of colors  (no black) and most of the time no writing. When I try to print in black only, I get nothing.
    What can I do? It worked just fine prior to ink going out.

    Did you get a resolution to your problem?  The same has occured for me - only printing blues/yellows and greens.  Was working fine until I replace the yellow cartridge and then it stopped printing reds.

  • White vertical lines when printing

    Hi hope someone can help me I have white vertical lines when printing photo tried doing the usual cleaning etc but still there.

    Hi SandyWilkey,
    It is recommended that you contact live technical support .  There is NO charge for this call.  Real time feedback of a live technical support call would be very beneficial in this case.  Please dial 1-866-261-9362, Monday - Friday 10:00 a.m. - 10:00 p.m. ET (excluding holidays).  A Canon technical support representative will be able to resolve this issue faster.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • I have horizontal lines when printing from my MacBook Air. Its nothing to do with my printer, as am now on to my third new printer, having returned the other two, saying they were fault. Now I know they weren't. Its got to be something to do with macbook.

    I have horizontal lines when printing from my MacBook Air. Its nothing to do with my printer, as am now on to my third new printer, having returned the other two, saying they were fault. Now I know they weren't. Its got to be something to do with macbook. I feel really guily about taking the other printer back, when it was fine!!

    Which MBA, which printer? Printer incl driver properly installed? Printed test page (yes, THE test page, not something else) and it looks okay?

  • How can I remove vertical lines when printing from Aperture 3.2.2 to Epson Stylus Photo RX690?

    I have been generally quite happy with my access to and use of Aperture 3.2.2 (recently purchased) for import and manipulation of photos and movies, etc.I am using Aperture on a MacBook Pro OSX 10.6.8.
    However I have been unable to print high quality images on Epson premium glossy, glossy or matt paper on my Epson Stylus Photo RX690.
    High quality prints on screen show perfectly in preview, but all prints come out with good and accurate colours, but a series of vertical lines or bands of lines across the photo print.
    Using the Aperture Manual I have checked my settings in Aperture for the printer, for colour and quality of paper etc and they all seem to be correct.
    The Epson Printer is networked with a Toshiba (Vista) laptop which prints perfect results from Picasa and Photoshop with fine colour and no markings.
    I would appreciate any help please.
    Cam Opie

    Thank you Mark
    I thought I had done all the settings .....but no.
    I now have perfect prints. Easy when you know how!!!
    Cheers
    Cam

  • Vertical lines when printing a PDF

    Software: Adobe Acrobat Standard 9.1.3.1 (German)
    OS: Win XP Prof SP3
    Printer: Lexmark C935
    Hello Community
    I have a strange problem: When user A tries to print out his building plans in PDF format on a Lexmark C935, there are vertical lines on the printout.
    What I tried:
    User A prints on another client: NOK
    User B prints the same document: OK
    Both users use the same printer with the same driver > shouldn't be a problem with the printer
    User A has the same problem on another client > shouldn't be a problem with the client
    Are there some user-specific settins that could cause these lines? I tried reinstalling Acrobat Standard, but it did not work...
    Any comments / ideas are appreciated!
    Cheers,
    Simon

    Try adjusuting your pdf page display settings (eg: turn off enhance thin lines).

  • Cm3530 colored vertical line when printing

    When printing over a wireless network (entire office is wireless but printer is wired), printout have a verticle blackish, blue verticle line on the left side of every page.  It does not happen when copying or scanning only printing from any PC.  I have changed the ITB and transfer roller.  This helps for a few days/weeks but the problem comes back.  I hate to throw parts at it again, ie, formatter or DC controller but I don't know what else I should do.  Anyone have any suggestions?
    I have had this printer for several years and it is now out of warranty and issue has just started about a month ago.  Any suggestions is greatly appreicated.

    @Scificajun 
    ‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
    If you are unfamiliar with the Forum's private messaging please click here to learn more.
    Thank you,
    Omar
    I Work for HP

  • HP photosmart 6520 e-AIO -- no black printing even after replacing cartridge

    I recently replaced the black ink cartridge in my photosmart 6520, and now the printer is just printing blank pages, sometime with a few faint black lines...help!

    Hi Jessica, I would advise calling HP Support about this....
    Troubleshooting steps
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=ie&lc=en&dlc=en&docname=c03954004
    Phone no.s
    http://welcome.hp.com/country/us/en/wwcontact_us.html
    Although I am an HP employee, I am speaking for myself and not for HP.
    Twitter: @Ciara_B_HP

  • Laser Jet 100 Color MFP M175nw "Very low" message even after changing cartridge

    Hello, Windows 7, 64 bit. Connection: USB. After a "supply very low" message for the black cartridge, I changed it to a completely new one (HP original toner with the hologram), but I still got a "very low" message and the print quality remained faint. Nothing worked: I tried the 3 solutions posted by Shirlzz1 to another user that had exactly the same problem (Alan_Gilmore), i.e. 1) taking out and reseating cartridges, 2) hard reset, and 3) taking cartridges out and hard reset, then reseating cartridges. I also tried a cleaning and a print quality report. All looked fine, but still "very low" message and faint print quality. The only thing that worked was changing the cartridge a second time to a completely different (new) one -- now everything's fine. So I'm guessing the first replacement cartridge I used is defective. However, is there anything else I can try with the apparently defective cartridge? They do cost a pretty penny, especially here in Denmark. Thanks for taking the time to look at this.

    Hi,
    Please check for these settings
    setup menu> system setup>supply settings
    Under this you have a option
    Black Cartridge
    very low settings>stop/Prompt/Continue, select continue
    low threshold> on/off
    same for color too
    Hope this helps
    Although I am an HP employee, I am speaking for myself and not for HP.
    *Say thanks by clicking the "Kudos! Star" which is on the left*
    Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.

  • TS2376 i have multicolored vertical lines on white screen after start up

    i have multicolored vertical lines on white screen after start up on macbook. how do i fix this?

    i have the same problem with my iphone 4s, im just waiting for it to die from battery but try rebooting,restarting or charging it

  • [LaserJet Pro 200 color MFP M276nw] only vertical lines when scanning, scanner broken?

    Hi all! I have a problem with the scanner in my HP all in one. If I scan (using the printer function or apples ImageCapture: same result) the output is just a lot of vertical stripes (in colors when in color mode). Not a trace of the image I try to scan. The lines are there even if i scan an empty white page. I see the stripes both when doing a preview scan and an actual scan. The problems are very similar regardless of if I use the flatbed or the feeder scanner (they are separate scanner hardware, yes?). I have updated to the latest software for the printer/scanner and I am connecting over bonjour via wireless. I am on Os X 10.9.1. Anybody having similar problems or is my scanner just plain broken? Thanks in advance!Jon

    , , I understand that both of you are seeing vertical lines when scanning from your Laserjet M276nw. First, make sure the printer is plugged directly into a wall outlet and not a surge protector. Now, so I know where to begin I'd need to know the following:If you are seeing the vertical lines when you copy as well as scan?Are you seeing the vertical lines when you copy from the flatbed? The document feeder? both?If you are seeing the lines from both the flatbed and the feeder are they in the same place?Once I know this I'll be better able to assist you.

  • HP Officejet Pro 8610 bought 2 weeks ago. giving vertical lines while printing.

    Dear Sir,
    I bought new officejet pro8610 . 2 weeks ago. its giving vertical lines on printing any document from printer. scanner is absolutely fine just problem while printing and copying. i clear printhead few times. 
    i just check that when i am printing any paper from windows photo viewer,there are lines like this.
    but when i copy the same image in Ms Word 2007 and print it from there. the paper is clean without lines. its strange. while i have anyother printer HP Laserjet Color CP1025 attached with same computer . i print the same image from CP1025 from Windows Photo viewer, its clean from there without lines. can any one help me out from this issue

    Dear Sir,
    I bought new officejet pro8610 . 2 weeks ago. its giving vertical lines on printing any document from printer. scanner is absolutely fine just problem while printing and copying. i clear printhead few times. 
    i just check that when i am printing any paper from windows photo viewer,there are lines like this.
    but when i copy the same image in Ms Word 2007 and print it from there. the paper is clean without lines. its strange. while i have anyother printer HP Laserjet Color CP1025 attached with same computer . i print the same image from CP1025 from Windows Photo viewer, its clean from there without lines. can any one help me out from this issue

  • OfficeJet Pro 8600 scans have vertical lines.

    I have a OfficeJet Pro 8600 and my scans have vertical lines.  Copying does not have the lines.

    I used the ADF and the flat bed to scan; both having lines as a result.
    In one of the forums and they thought it was static.  It was suggested to have the printer on and then unplug it.  Wait 15 seconds and plug it back in.  That did the trick.  No more lines.  I guess with winter bringing on more dry air, static is prevalent.
    Problem solved.
    Thanks

  • Pics have vertical lines throughout

    pics have vertical lines through them... thats black and white and color.... downloaded and ran scan on it and it checked out ok... what do i try now?

    HI bigchief1,
    Here is a link to a document that will help troubleshoot your issues. 
    Hope this helps. 
    If I helped you at all it would be great if you clicked the blue kudos star!
    If I solved your post please mark it as solved to help others.
    I'm a printer tech with HP.

  • Remove grid lines when printing

    I am trying to print a set of financial statements and do not want to see the grid lines when printing the final document. I cannot work out how to do this.
    Some posts I have read say that grid lines are described as cell borders and suggest that they can be removed using the inspectors "cell borders " facility.
    I have tried to do this but cannot make it happen. If I were to successfully remove the borders/grid lines then surely this would also remove the underlines I have inserted with great effort.
    I would really appreciate anyone's help with this

    One more time, it's useful to use our brain before stating a task.
    If I read well, you used some cell borders as an underline segment.
    Now you pay the result of a bad design.
    You have no way to remove only borders which aren't "underlining" ones.
    Next time think before and use the Underline text attribute so you will be able to remove the grid easily.
    I know that some spreadsheets have two structures :
    grid
    borders
    But, those which took time to read the User Guide know that in Numbers there is a single structure :
    borders.
    So, remove or hide grid means remove or hide borders.
    When we work with a tool, we may ask it what it is designed to do, not what we guess it will be able to achieve.
    Yvan KOENIG (VALLAURIS, France) mercredi 15 septembre 2010 20:51:51

Maybe you are looking for

  • How can I make my imap email not take the emails off the server?

    How can I make my imap email not take the emails off the server when I delete them on my iPad? Can anyone help me whith this? I tried to use the pop account in gmail settings but that was downloading all my emails sice 2008 ( more than 300 deleted em

  • My new wireless keyboard is intermittently losing connection.

    I broke a key on my original iMac wireless keyboard, so I got a new one. Ever since I got it a month ago, however, it will sometimes disconnect and the reconnect seconds later multiple times. It's really annoying, prohibiting me from typing and will

  • Intercompany STO with billing through a third plant

    Hi I have the following scenario: Stock transfer happens between 2 plants in 2 different company codes and billing happens through a third Plant which is in a 3rd company code. The supplying plant delivers the goods to the destination Plant and bills

  • HT4946 So how do I know my backup has all of my photos?

    So how is it i can know all my photos and videos have been backed up and are safe on my computer?

  • Using LR/Mogrify for sharpening, how to?

    I have been looking for a good way to approach setting the sharpening parameters for mogrify in LR/Mogrify, and I would like some feedback from people that know how. I found this article: http://redskiesatnight.com/2005/04/06/sharpening-using-image-m