I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

Similar Messages

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The wireless router works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The Airport works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

+For now I have it set to Share Public IP address - Is this correct for my Network Setup with The Airport Extreme being the only router being used ?+
This would be the correct setting if the AirPort Extreme is connected to a simple modem (one ethernet port).
*Settings I have Enabled*
5 GHz name indicates that you have elected to use the option to assign a separate name to the 5 GHz network. This will allow you to "tell" compatible computers to connect to that network, rather than the slower 2.4 GHz network
Use Wide Channels is recommended for 5 GHz operation.
Interference Robustness often does more harm than good and should not be used unless you know you are in a area with a lot of wireless networks and you feel that your network is experiencing interference issues from a nearby network.

Airport Express 802.11n + Airport Extreme 802.11n 2.4ghz but not 5ghz?

I can't get my Airport Express 802.11 to extend the network of my Airport Extreme 802.11n using 5Ghz only... but it will work with "n only 2.4Ghz"....
any solutions?
Message was edited by: Eric Carpenter

Addtional info both AE's now have ver 7.5.2 installed, prior it was 7.6 and situation is still the same.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but the printer won't work with the new one.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but I'm having trouble with the new one. When I try to print, I get a USB Waiting message on the printer, and when I force a page to print by pressing Go on the printer, I get a page that says ERROR: syntaxerror OFFENDING COMMAND: true. . . .cvt . . . fpgm . . . x . . .lglyf . . . <..J head . . . STACK: / [ -mark- /sfnts I’ve tried shutting down the printer and disconnecting it and the Airport, but that doesn’t help. I reset the settings on the printer. I upgraded the Airport firmware and removed, reinstalled, and upgraded the Lexmark printer driver. After I upgraded the firmware and printer driver, a few pages printed correctly, but then I got the same syntax error page as before. Any suggestions for getting the printer to work correctly?

Use a powered USB hub between the AE and the printer.. the usb port does sometimes have issues.
Try deleting the printer in the Mac and reinstall it.. the change in AE can represent effectively a change of printer.. it is important to make sure that is all up to date.
Beyond that.. USB printers.. ughhh! Consider for two toners you can go and buy a proper network printer.

I just purshased AirPort Extreme 802.11n wi-fi I was told to get the step by step direction on the internet and I am not able to find it can you help me

I just purchased AirPort Extreme 802.11n wi-fi I was told to get a step by step direction to install this wi-fi on line but I am not able to find it. can you please help me?
Helen

See this Apple video tutorial.
http://www.apple.com/findouthow/mac/#wirelesssetup
And this Apple doc:
http://manuals.info.apple.com/en_US/airport_extreme_5th_gen_setup.pdf

Timed Access not working on new Airport Extreme (802.11n).

I bought a new Airport Extreme (802.11n) to use as a router for my network. The network has a mixture of Macs and PCs, using a mixture of wired and wireless connections.
I configured the security settings with on the Airport Extreme to Timed Access. I set the default setting is to No Access.
Three computers are set with "Everyday, Between 8:00am and 11:00pm"; however, when it's 11:00pm, nothing happens. The three computers continue to have access.
I know the MAC addresses I entered are correct. Does anyone know why the Timed Access is not working?

Yes, the printer was initially set the same way it always was on my old router. It used to pop right up on the list. After I switched I was getting communication errors. Ok, new setup, I wasn't worried yet. When I got to the setup window and it a new printer wasn't found I tried updating drivers. No luck. I then used the IPP mode to enter the IP address with the address on the Canon screen. It failed. I then did the same setup telling it which software from the driver list to use. It still could not see it. The odd part is that the Canon can obviously see the router as its LAN setting read active and it is receiving the IP. I have proceeded to play with every setting on the printer and it is back to factory reset. Oh, I should mention that I have also tried to use Canons network setup utility software and it can not find the connection either. So I really think this is a problem within the router. I have seen many complaints about this on other forums, but most were looking to use the usb on the print server. My Airport is nowhere near my printer and I don't want to lose my all-in-one functions. Some think hard lined ethernet is ancient, but it really is a nice setup. Fast and reliable.

WMM for AirPort Extreme (802.11n) - UMA T-Mobile not working...

Is there any chance we'll see WMM (WiFi Multi-Media) in a firmware upgrade anytime soon? I noticed that according to the WiFi Alliance's website, when the AirPort Extreme was certified, it supported WMM!
http://certifications.wi-fi.org/wbcscertified_products.php?search=1&advanced=1&lang=en&filter_company_id=&filter_cat egory_id=&filter_subcategory=&filter_cid=&date_from=&date_to=&x=30&y=18&selectedcertifications%5B%5D=33
As an early adopter, I just got a BlackBerry 8320 from T-Mobile, which does UMA, so you can use the phone over WiFi. Works awesome with wireless routers that do WMM, basically doesn't work with my AirPort Extreme... As you might imagine, this is quite frustrating, as I have particular desire to have two APs, for basically no reason!
--Donald

I shot this across... let's see if anything comes of it:
~*~
To: [email protected], [email protected], [email protected]
Subject: a rather pressing Airport Extreme (802.11n) issue
i'm not sure if the person receiving this email will have any power (or will
care enough) to do anything about sorting this problem out, but hey...
better to try and fail than not trying at all, right?
anyway... here goes:
i am a die-hard apple user- heck, even a long-time stockholder- and recently
bought an airport extreme (802.11n) router for my house. it worked
flawlessly and i thought it was the best thing since sliced bread... well,
until i picked up a UMA phone from T-Mobile.
UMA is a service that routes your calls over WiFi. for some reason the UMA
service worked everywhere except over my Airport Extreme base station. as a
surprise, it even worked over my neighbour's older Airport Extreme (802.11g)
connection.
i swapped base stations (ie, brought his base station to my house, connected
it to my network) and it worked. so, it is an issue that is clearly
isolated to the new 802.11n base stations.
thinking it was only me with this issue, i dug around the internet and found
this discussion:
http://discussions.apple.com/thread.jspa?threadID=1152014&tstart=15
(if you want more, just google the keywords 'airport extreme UMA')
obviously there's no resolution and people are getting quite peeved that a
state-of-the-art base station can't do something than an older base station
can clearly do. so, can someone please look into this?
thanks!
pramit
~*~

Airport Extreme 802.11n (4th Generation) vs. MBP 2006. The MBP is losing :(

GRRRRRRRRR— I feel like this is a version of a problem I see repeated here endlessly, but none of the threads I see about it is quite the same, or fixes my problem.      We have a network with:
Airport Extreme 802.11n (4th generation), connected to DSL modem. Firmware 7.5.2
MBP 2006, running OS 10.6.7 ****
MBP 2008, running OS 10.5.x
ipads, iphone, shared printer, drive, etc.
Everything works fine EXCEPT the MBP 2006. It connects to the network, works for a while, and then after a certain amount of time (anywhere between a minute and several hours) it's dropped. The menu bar still shows a connection and full signal, but there's no connection (TCP or afp) and when I launch the Aiport Utility, it just says that no base stations can be found.   The menu bar seems to be lying. Using the menu to turn Airport off and back on (or sleeping the laptop) works to reestablish the connection.
I do not have this problem with the MBP 2006 on other wireless networks (at work, or at my other home in another city). Just with the Airport Extreme
I've tried changing the channels, disabling IPv6 on the laptop and on the Airport Extreme, setting up a manual DHCP address, and changing the setting for "radio mode" of the base station from Automatic to 802.11a/n - 802.11b/g/n.   I also read that there might be troubles with "mixed" networks with both 802.11g and 802.11n, so I upgraded the Airport card in my MBP 2006 to an AirPort Extreme 802.11 a/b/g/n, which made disk sharing much faster when it's working, but didn't put an end to the cut-outs
Hjalp? Why does the Airport Extreme keep dropping my MBP 2006 (or vice versa)? Are there other things I should be changing or disabling?

OK, two possible leads:
1) Using the AirPort Utility, I disabled 802.11n, setting the AirPort Extreme to b/g only. This seemed to help— I didn't fall off the network all afternoon. (Setting it to 'n' only did not work, unfortunately, or else that would have been better, since it would have let me take advantage of the faster speeds for Time Machine to the shared disk)
2) Soon thereafter, for seemingly independent reasons, we starting having trouble with our DSL connection. We reset the AEBS to factor settings, which didn't solve the DSL problem (had to get a Windstream technician out for that), but since that reset, I've been connected with 802.11a and the MBP hasn't fallen off the wireless network once.
We'll see how it holds up, but for now, the recommendation seems to be first to reset the AEBS settings to factory default, and then try disabling 802.11n...

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

Plenty of suggestions.. only you can find out which one is correct.
What model AE? What firmware?
Since Panasonic TV is not apple it will use SMB windows type networking.. everything but Apple does.
Are the names in the AE all SMB compatible.. ie short.. max about 20 characters.. no spaces and pure alphanumeric.
Is the security set to WPA2 Personal with a pure alphanumeric password of 10-20 characters.. more is fine if you suffer paranoia but isn't needed.
Fix the wireless channels.. so it doesn't flip flop like a dying fish.
There are only 3 channels for 2.4ghz that do not overlap, 11, 6, 1 although someone suggested 8 works well if you have heaps of interference. If you live in flat/apartment building you have heaps of interference.
Lastly is it stable if the distance is 3M direct line of sight?
If not then get a high power wireless AP and use that instead.

AirPort Extreme 802.11n* Enabler not working

Hello, I just installed the Time Capsule software onto my 1st gen MacBook. I saw that it installed the AirPort Extreme 802.11n Enabler, but after looking at the network utility. All that show up is: Wireless Network Adapter (802.11 a/b/g), it does not give the little 'n.' I ran the installer twice, but no joy. Any help would be great!
Thanks!

ursina, Welcome to the discussion area!
Go to the Apple menu and select about this Mac. Does it say "Intel Core Duo" or "Intel Core 2 Duo"?
Only the Macs with "Intel Core 2 Duo" processors have the 802.11n hardware. If you Mac book has the "Intel Core Duo" processor the enabler is useless.

Not able to see disk connected to AirPort Extreme 802.11n

I just installed my AirPort Extreme 802.11n Wireless Base station. Wireless internet works like a charm, however, I cannot see my external hard disk when it is connected to the base station (amber light blinking and when checking the problem, I am told that "Disk needs repair"). When connecting the hard disk directly to the PC, I have no problem seeing the data. Any tips or tricks out there... ?
AirPort Extreme 802.11n Windows XP

I finally got my 500 GB Western Digital MyBook USB drive to work by reformatting it to HFS+ format.
Of course, before I could do that, I had to copy all my files onto another hard drive. That job took a day to accomplish.
I work with Poser, and have a lot of content installed... We're talking thousands of files.
Once the drive was reformatted to HFS+ format, I copied everything back over. That took another day. Then I connected to the AEBS.
The USB drive was immediately recognized. It was incredibly easy to access the USB drive on my PCs. It required no effort on my part, except to supply the password.
In the end, I've decided this effort is a failure.
The drive is way too slow for my needs. Also, one of my vital Poser utilities (CorrectReference Pro) will not work properly with the USB drive on the AEBS.
I am currently in the process of copying all those files over to two external USB hard drives attached to my other PC.
Then I plan to unmount my 500 GB MyBook drive, and reformat it back to NTFS. I'll let the Notebook PC have it on a direct connection again.
I have a couple "junk" External Hard drives that are 160 GB. Maybe I'll use one of those as an Airport disk...
But I won't be using the Airport disk for anything important. It's too slow.

Airport Extreme 802.11n sharing a disk with a -1 on the mount point

First I have to reboot the device once a day because of the disk that disconnect for no reason like many other on the list ever since I upgraded to 7.2.1 but not sure that as to do with this problem.
Here's is the deal, I have an Airport Extreme 802.11n with a 500GB shared on the USB port. I want to use my iPhoto Library on the 500GB. It's about 11GB, I have tranfered the library over and iPhoto is asking to choose the library I want to use. When I try to point it to the 500GB everything is greyed out. When I use a terminal and do a df command to show the mount point on my computer, I get
/Volumes/500GB-1
Why and where the -1 is coming from?
How can I get /Volumes/500GB only?
One thing I have noticed about the -1 is when I loose the disk connection it prompt me to disconnect 500GB-1 but sometime even with a -2 and -3.
Thx!

can I hook up my printer, scanner and external harddrive through a usb hub?
Partially, a large number of USB printers will work with the AirPort Base Stations' USB port, but not all. I suggest that you checkout the following iFelix site to see if your printer is compatible. Similiarly, most external USB hard drives should work as well.
However, devices that rely on two-way communications, like copiers and scanners, won't work when connected to the USB port.

Airport Extreme 802.11n Wi-Fi not working

I just purchased Apples Airport Extreme 802.11n with the idea of getting just a bit more range than my old airport. This is/was hard to tell since I could not get the unit to function properly.
My internet service requires two address but this A/P Extreme only allowed one. This A/P Extreme 802.11n totally shut down my internet service. It did not allow wireless connection with other computers. The range seemed to be less than my older Airport Extreme 802.11 a/b/g.
I had to re-install my Airport Extreme a/b/g to get things working again.
I went to Apples Products and Service page to find out about the Express registration. Apples registration system did not recognize my serial number. Apparently their specification page recognized some parts of the serial number since the web page did display specification for the Airport Extreme.
DOES ANYONE KNOW THE REASON FOR ALL OF THIS TO HAPPEN?

You said you went to the "Express" page and tried to register above. It may be because you tried to register an Extreme as an Express. I had some difficulty over two months ago registering my Extreme. It let me register it without all the data because it would not recognize the serial number. Called Apple Care and they made sure it was registered.
Also, unless you have an all 802.11n system, you may get a little more range out of the Extreme, but I don't think any more than if you would have used an Airport Express 802.11g. Range and speed are geared toward all n systems.

User Contributed Tips in the AirPort AirPort Extreme (802.11n) forum

*The following User Contributed Tips are located in the AirPort > AirPort Extreme (802.11n) forum:*
adsfushi72 - What does this acronym mean?
http://discussions.apple.com/thread.jspa?threadID=2450065
Publish date: June 4, 2010
William Kucharski - Having issues with your AirPort connection? Please be specific.
http://discussions.apple.com/thread.jspa?threadID=2227197
Publish date: Nov 21, 2009
William Kucharski - Apple AirPort drivers only support a WEP key index of 1
http://discussions.apple.com/thread.jspa?threadID=1654663
Publish date: Oct 16, 2008
*The following related tips are located in other areas of Apple Discussions:*
a brody - Airport, 10.5.8, and MacBook and MacBook Pros and slow internet
http://discussions.apple.com/thread.jspa?threadID=2291464
Publish date: January 7, 2010
Rich Love - Airport and Roadrunner (Jan 6, 2002)
http://discussions.apple.com/thread.jspa?threadID=121815
Mark Lansdown - Semi-wireless Wake on Lan (Oct 8, 2008)
http://discussions.apple.com/thread.jspa?threadID=1276830
Pondini - Using Time MACHINE with a USB drive connected to an Airport Extreme
http://discussions.apple.com/thread.jspa?threadID=2299608
Publish date: January 14, 2010
See also the User Tips Library

Ask yourself a question.
How fast is your internet connection?
If it is is 1-2-8 mb speed then you dont need 'n'.
If you transfer personal info between computers fast speeds allowed up to 54 will save you time.
'n' is to provide greater range like Mimo and increased transfer speeds.
But do you really need it?
No,if you dont transfer huge data,
Yes, if you want to transfer (stream video from your iTV from Mac if you spend most of your day in front of TV.
There is no substitute for a good reliable connection.
In my real world experience because I only have a 8mb ADSL connection 'g' is not the strongest and most reliable scenario to use. During the last airport update my last 3 years of uninterrupted airport connections mixed PC and Macs on WDS set up went belly up and I had posted my thoughts as well with the relevant results and now set up is fine. But at a price.
Downgraded to all on 'b' and now use my Draytek Vigor 2800VG and have AEBS put away in storage.
My signal and range is out of this world. When I decide that I have enough free time to sit in front of a TV and download movies and watch them when I have nothing better to do such as travel the world etc. etc., that is the time I will go for speed...or will I.
Dont get bamboozled by the hype. If you really want one wait for a year then decide. Let others solve the teething problems as is there want.

Speed issue with the AirPort Extreme (802.11n)

Hi, I was wondering if anyone could help out with this.
I am the Design Manager and IT Director at a publishing company where we have just upgraded to an AirPort Extreme (802.11n) base station to drive our network. We went this route as all of our machines are Mac Minis with built-in Airport and we were in a situation where re-doing a hardwire on the building was not going to be a possibility due to budget costs.
Our new configuration seems to be running very well and has the following devices connected to the AirPort Extreme:
Linksys Firewall Router (which was used on our old system and was requested by corporate to stay in the lineup to keep the static IP addresses we've already defined for our printers, VPN, etc. intact). The configuration on this part is modem to Linksys router to uplink port on the Airport).
New Panther, Intel based Xserve connected to the Airport's Ethernet port 1.
A 4 port ethernet switch connected to the Airport's Ethernet port 2 which drives four of our HP LaserJet printers.
Ethernet port 3 is not occupied.
All of the ethernet cords connecting our equipment are brand new.
For the most part, everything's been running blazing fast with a remarkable speed increase over our old hardwired setup. However, I've received a few complaints about slow speeds when dragging and dropping and working with files that are stored on our Xserve - we get alot of the "spinning wheel" and the transmission speeds seem very slow.
At present, we have several category 6 ethernet cords on backorder. I was planning on using one to take advantage of the gigabit ethernet capabilities between the Airport and the Xserve (as these are the only two elements of the network that support gigabit ethernet, besides the majority of our Mac Minis. Printers and cable modem are only 10-100 capable, so those will stand as is).
Can anyone tell me if the gigabit ethernet cord will be the solution to this one slow aspect of the new network? Any other settings I could apply to possibly speed up the transmission time when moving files to and from our server? Good news is that every workstation in the house is getting a full 4 bars.
Many thanks!

PS, just wanted to point out that we are also running in bridge mode.
Thanks!

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

Similar Messages

Maybe you are looking for