I know that an Airport Express extends my wifi range, but does it stretch out my Broadband or does it increase it?

I was thinking of getting a seperate wifi account for my basment, but would it be better to get an Airport?
Does an Airport boost internet?

No, worse.
If you're extending your network wirelessly with another device (extreme, express, etc) it can CUT your performance by up to half. You really should find a way to run an ETH cord down to your basement and extend the network via a wired connection.

Similar Messages

Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range

Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range.

You cannot extend wifi from a different brand router..
Only apple to apple.
But the apple router does not have to be the main router.. it can be in bridge.. as long as it is creating a wireless network it will work fine.

Using AirPort Express as a WiFi Range Extender

I have a Westell Versalink 327 W combination DSL Modem and Wireless Router downstairs hooked up to an iMac via ethernet cable. Can I use the AirPort Express as a WiFi Range Extender upstairs? Any issues I should be aware of?

I suggest that you check with DLink on this as using the same manufacturer will always give you the best chance at compatibility.
Maybe this would do it:
http://www.dlink.com/products/?pid=357

Airport Express extending Time Capsule Range

I have a fairly old Airport Express. 2-3 years old. Does this mean its not possible to extend the range on my Time Capsule running as main wireless? I just want to extend the range, but tried to join the network my Time Capsule was running (while backing up my Macbook Pro).
I'm wondering, was it unable to join because my Time Capsule was currently backing up files? Or is it unable to do so because of the 802.11n (or lack thereof).
Hope this makes some sense. Thanks

You can extend the wireless range of the Time Capsule (TC) with the older 802.11g AirPort base stations in a configuration known as a Wireless Distribution System (WDS). However, note that the new combined network will only operate in the 802.11g radio mode.
Here are the basic steps in configuring a WDS with these two devices:
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs for each of the base stations to be used in the WDS.)
o Perform a "hard" reset on the Time Capsule (TC) and a "factory default" reset on the 802.11b/g AirPort Express Base Station (AX).
Main Base Station Setup - TC
o Click the AirPort status menu in the menu bar and choose the wireless network created by the TC.
o Open AirPort Utility.
o Select the TC, and then, choose Manual Setup from the Base
Station menu.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the AX.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup - AX
o Click the AirPort status menu in the menu bar and choose the wireless network created by the AX.
o Open AirPort Utility.
o Select the AX, and then, choose Manual Setup from the Base Station menu.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the main base station in the WDS Main field.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)

Airport Express Extends 5GHz at 2.4GHz?

My second generation(802.11n) Airport Express extends my 5GHz network, Net5, at 2.4 GHz. The express is about 20
feet from its "target," an iPad 3 serving as an internet radio. I know this because a scan turned up the 5GHz network on the same
channel as the 2.4GHz one and identified as "Net5."
As far as I can tell, all my settings are correct, etc. I'd be grateful for any ideas, comments, etc.

Ok, thanks for clarifying that for me. By default, the 2nd generation Express should extend both radios of your 5th generation Extreme. The key is placement. As you are already aware the range of the 2.4 Ghz band is greater than that of the 5 GHz one.
Even if you have the Express within 20 feet of the Extreme there may be some form of Wi-Fi interference (like walls) that may be preventing the 5 GHz band to be extended properly.
To rule out a possible placement issue, please check out the following AirPort User Tip for details on how to best place your base stations.

Problem with airport express extending wifi from extreme

My setup is an airport extreme wired to the internet with two iMacs connected by wire and an airport express to extend wifi from the extreme to the further parts of my house. When originally installed about a year ago this arrangement worked perfectly, but I noticed a few weeks ago that neither my iphone, ipad, nor my MBP 13" is connecting to the aitport express anymore and the network extension is not working as intended.
Last night I investigated the isue and found that the express is connected wirelessly to my extreme because when I wired my MBP to the express and turned off the wireless connection it could still reach the internet. But, even with the express sitting plugged in next to my iPhone I could not get it to connect to the express - it always uses the extreme and while I'm in range there is no problem. The problem is that my house is old and the wals tend to cause problems with reception and I can't get wifi in the garden and some parts of the house.
I have the express and the extreme configured to allow access only by the client macs that I have provided and it looks like the two devices share this information when they are in extend mode (but not sure about that). When I set up the system I added the aitports mac addresses to the approved list in the access control screen, which seemed to be necessary then though I removed them (the airport mac addresses) fromt he list last night to see what effect this had and biefly the airport did connect to my MBP. But after returning it to its location where it usually is I have not been able to reconnect to it.
In brief; I have an airport express extending an airport extreme wifi, it used to work, but now all wifi clients will only connect to the master. I have a suspicion that a recent airport update has caused this (both airports are up-to-date) but can't be sure. I have the express correctly configured to extend the wifi of the extreme as it was originally working.
One thing I have noticed - I had the express set to use a fixed IP by setting 'static' in the internet screen - this is not the current setting (it's reverted to DHCP) and I cannot force it to update to and remain set to static.
Does anyone know how I can restore the correct functioning of the express as an extension of the wifi network?
Thanks
Damon

Perform the Factory Default Reset one more time. Hold the reset button until the amber light has been blinking rapidly for 8-10 seconds before you release the reset button
Run the setup wizard, and wait for screen similar to this to appear, then click on Other Options:
Select the Add to an existing network option, then click Next and follow the prompts.
If you are still having difficulty, try running the setup utility on an iPhone or iPad, since Yosemite has a number of bugs in the setup process.

Airport express extending wifi extremely slow

Hello,
I have a time capsule creating a wireless network and a airport express extending the wireless network.
When I'm connected to the time capsule I have around 12mbp of speed but when I am connected to the airport express I have around 0.2mbp
In the airport utility it says the connection is good she connected to the airport express.
Everything was working fine a few days ago.
I was reading the the forum that it may be interference from a neighbour and to change the channel but I can fine where to change the channel.
Is changing the channel the solution? How can I access where to change the channel?
Or is there another solution?
Anyone knows how to fix this speed problem in airport express?
Cheers
Francisco

What is the distance between the Time Capsule (TC) and the AirPort Express Base Station (AX)? Are they in the same room, different room, different floor from each other? If in different rooms/floors, what is the basic building material used in the walls/floors/ceilings?
It is important to understand that the AX can only extend the TC's wireless network at the same bandwidth that it receives it. If you are only getting around .2 Mbps at the AX, then either there is too much distance between routers or there is some form of Wi-Fi interference (other Wi-Fis or the builiding material) between them that is preventing the AX from getting a strong enough signal to extend.
Changing channels is one possible solution. You would do so using the AirPort Utility. If you are using version 5.x of that utility, you would change channels as follows: AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless tab > Channel. By default Channel is set to "Automatic." Click on the up/down arrow to the right of the Channel window to get the other channel options.
If this doesn't resolve the problem, please check out the following AirPort User Tip for details on how to best place each base station for maximum bandwidth in an extended network.

AIRPORT EXPRESS EXTEND OR JOIN !

Dear All,
I have a doubt in my mind. I have a Airport express latest model and an Airport Time capsule 2 Gb (latest tower type), I also have a Bose lifestyle 135 series to which is connected a apple TV 3.
Now my motive is to connect the airport express in such a way that the sound is played through my bose systems, for that should i connect my airport express to my bose lifetsyle 135 or should i connect it to my apple tv 3 ?
secondly my primary rounter is apple time capsule 2 gb, which make my house wifi and as we all klnow it is WIFI 801.11 AC , now if i use my airport express to extend the network on wifi then will the wifi speed reduce as the airport express is not WIFI 801.11 AC and it is WIFI 801.11 n !!!
I am confused for these would appriciate if any one could help me out with the same.
Regards
Vinay Kittur
00971501701356

Now my motive is to connect the airport express in such a way that the sound is played through my bose systems, for that should i connect my airport express to my bose lifetsyle 135 or should i connect it to my apple tv 3 ?
If the Apple TV is working well now, there is no reason to change to an AirPort Express for this purpose.
if i use my airport express to extend the network on wifi then will the wifi speed reduce as the airport express is not WIFI 801.11 AC and it is WIFI 801.11 n !!!
You already know the answer to this. The AirPort Express cannot extend an 802.11ac signal, so the signal will slow down to 802.11n if you use the AirPort Express.
If you want to extend 802.11ac, then you need a new AirPort Extreme for that purpose.

Airport Express extends 5 Ghz and 2.4 Ghz or just one at a time?

I recently switched my dual band Time Capsule to use different names for the 5 Ghz and 2.4 Ghz networks.
Will the Airport Express extend both or just one at a time, if so, which one will it extend?
I have two Airport Express modules, bought a long time apart, is there any difference in functionality and how do I tell them apart if this is the case?
All are running the most recent firmware version.

Welcome to the discussion area, Mike!
Will the Airport Express extend both or just one at a time, if so, which one will it extend?
The AirPort Express is a single band device, so it can extend either the 2.4 GHz or 5 GHz band, +but not both at the same time+. Since you have different names for the 5 GHz and 2.4 GHz bands, the Express will extend the 2.4 GHz band by default. Using AirPort Utility, the setup application for the AirPorts, it is possible to configure the AirPort Express to extend either band.
If you are perhaps thinking of extending the 5 GHz band, this can be a bit tricky because 5 GHZ signals do not travel effectively over distance or penetrate obstructions as well as 2.4 GHz signals. You almost have to have a line-of-sight relationship between the Time Capsule and the AirPort Express to be able to extend the 5 GHz band.
I have two Airport Express modules, bought a long time apart, is there any difference in functionality and how do I tell them apart if this is the case?
Look on the side of the AirPort Express for the model number in the small print. You'll need Model No A 1264 to be able to "extend". If you have the older Model No A 1084, that version will not be able to "extend" a wireless network, but you could use it to "join" the wireless network and stream AirTunes to the device.
All are running the most recent firmware version.
That would be 7.5.2. If you have the older version of the AirPort Express, the latest firmware version for that device would be 6.3.
Message was edited by: Bob Timmons

HI, do you know how many airport express I can use per Mac????

I need to know how many airport express can I use simultanously in my Mac ... any idea???

Thanks for your question, I live in a 3 floor house, the cable router is in the 2nd floor, I already have one connected airport exrpess in the 1st one, but I need to increase the wifi signal in the 3rd one... so for that reason I would like to conecct one additoonal one to my wifi network...

Airport Express extending network needs to be restarted daily

I'm having a really annoying problem with my Airport network. Here's the configuration:
Den: Latest generation simultaneous Dual-Band Airport Extreme
Living Room: older 802.11g Airport Express used only for AirPlay
Office: older 802.11n Airport Express wired to the Airport Extreme via ethernet, extending network
Hallway: 802.11n Airport Express wirelessly joining and extending network
Bedroom: Latest generation simultaneous Dual-Band Airport Express wirelessly joining and extending network
I have an older house which is not terribly big but the radio-opaque walls make it difficult to propogate wireless, thus the need for so many units.
It all works pretty well except for my bedroom Airport Express (simultaneous Dual-Band). On a daily basis it will lose connection with the network or go so painfull slowly that it's pointless. The only solution is to do a reboot of the unit which works temporarily (good connection / good speeds) My son likes to watch Roku in our bedroom and that Roku uses the WiFi that the Airport Express should provide. Needless to say troubleshooting wifi when your 3 year old is crying because he can't get 30 seconds of streaming before the signal craps out is not fun. Anybody have any suggestions???

"Hard reset" the bedroom Extreme to preclude the possibility that some corrupted internal parameter is limiting its performance. Consider doing that with all of them. They will subsequently need to be reconfigured.
Configure the den Extreme to provide a unique name for its 5 GHz network, and ensure all the devices capable of using it are using it, and not 2.4 GHz. Find out what your Roku is capable of using.
The key to solving problems, if your challenging requirements are solvable, is to start with as simple an installation as possible, then progressively add to it. Find out the maximum usable range of your den's Extreme in both 2.4 and 5 GHz bands, then position any devices used to "wirelessly extend" its signal roughly half the distance to that Extreme - not a different base station. The ideal location for the Roku's Express may not necessarily be in the bedroom.
Run speed tests each time and make sure you are not trying to "extend" a weak signal. "Extending" a weak signal makes it stronger, but no faster that what it receives.
That's all you can do.
... I thought "N" networks minimized that problem.
You're right about that.
The thing is I get decent wireless reception in the bedroom WITHOUT the express plugged in.
I wonder if those devices are really using the Express you think they are. That's the problem with multiple base stations. There are ways of addressing this question but not with the current AirPort Utility version.

Can I use Airport Express as a Wifi Extender?

Forgive my ignorance, but I just swithed to all Apple products a few months ago and I have a question about the airport express.
We currently have one airport extreme base station set up in our house. The only problem is that the g signal for my iPhone won't reach quite far enough to get to the third floor (its a very long and tall home).
I was wondering if you can use the Airport express as a wifi extender with no cords plugged into it, similar to the linksys extenders you can buy that extend the signal range.

LukeW, welcome to the discussions!
Yes, an AirPort Express could be used with your Extreme to "extend" the wireless network created by the Extreme. I assume here that you have an "n" capable Extreme.
If you have an older 'g" Extreme, the Express could be used to "participate in a WDS" (wireless distribution system), which is a similar setup.
It will probably take some experimenting to find the best position for the Express (you want it to receive as strong a signal as possible and "extend", so a good starting point would be to place the Express at a point that was roughly half way between the Extreme and the area that needs more wireless signal.

Airport express extending - n AND g

I have an airport express extending a dual band airport extreme network. The extreme has one band on n (for laptops) and one band on a/g (for iphones and an older laptop). The airport express extends the network, connecting wirelessly to the extreme in another room, and sharing its connection with an iphone and an old laptop.
My question is this: will the airport express connect with the airport extreme (receiving its internet connection) at n speeds, but then connect with my iphone and old laptop (sharing its internet) at a/g speeds? I know the express is not dual band and thus cannot share its connection on different bands, but can it connect on a different band than it shares?
Thanks!

From what I've tried the Airport Express will only extend as it connects to. I've tried and it doesn't seem to "auto-convert" from one to another.
Also, you might want to look at the 802.11n 5ghz and 802.11n b/g/n 2.4ghz. Set this in your Airport Extreme accordingly (which you already might have), and let Airport Express automatically extend the 802.11n b/g/n 2.4ghz. This way, the iPhone will connect as fast as it can and the older laptop can connect.
BTW here is my "poor man's dual band" setup if anyone's interested:
DSL modem is connected to Netcomm 802.11b/g/n wireless router. This supplies the 802.11b/g/ 2.4ghz N signal for iPhone, Xbox360, and anything else.
Then, I connect via ethernet from Netcomm wireless router to my existing Airport Express. Airport Express supplies a pure 802.11 5ghz N signal for my Mac, iPad2, new iPad and AppleTV.
This way, the Mac, iPads and AppleTV always "see" only the Airport Express network, hence WiFi iTunes syncing as well as AirPlay streaming is great, and the 5ghz network with maximum N speed doesn't suffer interference and/or dropouts such as when my microwave is running.
As for the iPhone, I'll just use a cable when I need to, but this way my iPhone and Xbox360 can access the Internet as needed without degrading the connectivity of the Mac, iPads and AppleTV. I don't play online games, I only need connectivity to update or download stuff on Xbox360.
Yes, the disadvantage is double-NAT, but I haven't encountered issues yet.

Macmini sharing - airport express extending?

I've set up my macmini to act as a base station through network sharing. But now my airport express won't allow me to run airtunes. I've tried to get the airport express to pick up the macmini network in client mode but it just says it can't find a base station. When I try and use it for airtunes it tells me that the airport in my macmini is in use and to turn it off.
Is there a way to get the express to extend the wireless network created by the macmini? Or to get my airtunes to work whilst the macmini is a base station?
hope that makes sense! I've searched far and wide...

From what I've tried the Airport Express will only extend as it connects to. I've tried and it doesn't seem to "auto-convert" from one to another.
Also, you might want to look at the 802.11n 5ghz and 802.11n b/g/n 2.4ghz. Set this in your Airport Extreme accordingly (which you already might have), and let Airport Express automatically extend the 802.11n b/g/n 2.4ghz. This way, the iPhone will connect as fast as it can and the older laptop can connect.
BTW here is my "poor man's dual band" setup if anyone's interested:
DSL modem is connected to Netcomm 802.11b/g/n wireless router. This supplies the 802.11b/g/ 2.4ghz N signal for iPhone, Xbox360, and anything else.
Then, I connect via ethernet from Netcomm wireless router to my existing Airport Express. Airport Express supplies a pure 802.11 5ghz N signal for my Mac, iPad2, new iPad and AppleTV.
This way, the Mac, iPads and AppleTV always "see" only the Airport Express network, hence WiFi iTunes syncing as well as AirPlay streaming is great, and the 5ghz network with maximum N speed doesn't suffer interference and/or dropouts such as when my microwave is running.
As for the iPhone, I'll just use a cable when I need to, but this way my iPhone and Xbox360 can access the Internet as needed without degrading the connectivity of the Mac, iPads and AppleTV. I don't play online games, I only need connectivity to update or download stuff on Xbox360.
Yes, the disadvantage is double-NAT, but I haven't encountered issues yet.

MacBook Pro that my Airport Express WiFi profile was created crashed. Can i reset the Airport Express either to an iPad or Windows 7 computer?

MacBook Pro that my Airport Express WiFi profile was created crashed. Can i reset the Airport Express either to an iPad or Windows 7 computer?

Get the Airport Utility for the your iPad from the App store. You will need to know the password for the Airport Express (not the WiFi password) to access the AE. The iPad utility will, I think, do all of the actions to control your AE.
You can reset the AE back to factory default but with the iPad app you should not ned to.

I know that an Airport Express extends my wifi range, but does it stretch out my Broadband or does it increase it?

Similar Messages

Maybe you are looking for