I LOADED NEW HARD DRIVE IN MY MAC PRO AND NOW I'M GETTING A GREY SCREEN!

I REMOVED MY 160GIG HARD DRIVE OUT OF MY MACBOOK PRO AND REPLACED IT WITH A 320GIG NOW WHEN I GO TO LOAD MAC OS X DISC I GET A GREY SCREEN THAT READS CAN'T FIND DRIVER! CAN SOMEONE PLEASE TELL ME WHAT YOU THINK THE PROBLEM IS OR WHAT I SHOULD DO NEXT.

Did the computer ship originally with a Tiger 10.4.x system, and was the Snow Leopard 10.6
disc used to upgrade the OS from 10.4 to 10.6? Or are you using a Leopard 10.5 disc?
Sometimes an error can result when reinstalling a later OS in a computer that had been
running an older computer, when the former setup had seen a firmware update. And in
a few other situations, if 10.5 was skipped, and OS 10.4 to 10.6 was the path, a few users
had noted problems later on. Since you did not note if the computer was new enough to
have shipped with Snow Leopard (thus perhaps had AppleCare plan coverage, too) these
other questions arise to find those details.
There is some conflicting (or missing information) in your posts; just enough
to see the problem may be in what you have and how you are using it.
Is the latest software version you have a full retail version of the OS X, or was it an upgrade
disc (such as the low-cost upgrade for Snow Leopard) used over an older 10.4 OS X version?
Was a firmware update performed on the computer with the other installation of this software
before you replaced the hard disk drive? Sometimes a firmware update to the logicboard may
cause a problem in later installs of an older OS X than the last one the firmware update was for.
If there were jumper pins to be set specific to use it correctly in this computer, before installing the
new hard disk drive, and if they were not set accordingly, the computer may not see an install disc
or be able to use the disc to install an OS X. Other difficulties may result, if not immediately.
There are details missing in this discussion which may pertain to the outcome.
{And I pointed out your new thread on this same topic to forum moderators, since
you already had this one with replies; as duplicate questions are often not helpful.
That was in the Tiger 10.4 discussions area.}
Good luck & happy computing!
{ edited }

Similar Messages

  • I had to install a new hard drive on my macbook air and now I am getting unkown error whenever I try to login to itunes

    I had to install a new hard drive on my macbook air and now I am getting unkown error whenever I try to login to itunes. Apple support suggested I reset my password so I did that and still the problem is occuring. Itunes and the app store are working normally on my ipad and iphone. Does anyone know what the problem is. The new disk was installed in France coz I am on holiday there. could there be something I need to change in my settings? I need help urgently as I am trying to finish an assignment and need to be able to access and download from icloud.

    Hi Stacey,
    Thanks for visiting Apple Support Communities.
    You may find the tips in this article helpful with resolving the error you're seeing:
    iTunes Store: "An unknown error occurred (-9808)"
    http://support.apple.com/kb/TS2753
    Best,
    Jeremy

  • Apple put a new hard drive into my MacBook Pro and updated the system to Maverick. They did not put iPhoto and iWeb on it but I did have it in Lion. Why and what am I supposed to do?

    Apple put a new hard drive into my MacBook Pro and updated it from Lion to Maverick. They did not put iPhoto and iWeb on it but I did have it in Lion. They also didn't put Pages, Keynote or Numbers back on it until I argued with them. Of course, I didn't have my data backed up. My hard drive was destroyed when I tried to install the update of Mavericks myself. I should not have to buy iWeb and iPhoto when I already had them. Suggestions?

    cwhargrave,
    have you tried looking in the App Store, to see if you can redownload iWeb and iPhoto there gratis?
    If you haven’t done so already, you should purchase an external hard drive to act as a Time Machine backup destination, so that you’ll have an option to rollback to a working environment if a new OS installation is troublesome.

  • I just replaced the hard drive for my Mac Pro, and I am trying to restore what is on my Time Capsule, but it wont connect, and only is giving me the pinwheel of death. What do i do?

    I just replaced the hard drive for my Mac Pro, and I am trying to restore what is on my Time Capsule, but it wont connect, and only is giving me the pinwheel of death. What do i do?

    You will need to boot from some alternate boot device to accomplish this, if you did not initialize the drive before installing it.
    If you have another Mac, you may be able to use FireWire target disk mode.
    If your MacBook has a DVD reader and you have a Mac OS X Installer/Utilities DVD, such as the one that shipped with it, you can boot from that DVD, answer only the "what Language" question, and wait a quarter minute for the MenuBar to be drawn. Then examine the Utilities menu or the Installer menu and Find Disk Utility.

  • I need to buy some new hard drives for my Mac Pro

    I had an extra internal hard drive in my Mac Pro, a Seagate one, that suddenly stopped working and I needed to send it to a data recovery company, so...
    Now I'd like to
    - Install a new internal HD
    - Install a NAS with two/three disks. (Hitachi if possible, as I have read are the ones that last longer, more reliable than WD and by far more than Seagate).
    But to do that I'd like to know how to find out the right type of disks for my computer.
    I'd be very gratefull if anyone would tell me where to look it up.
    Thank you in advance
    In case any of you can help with this, these are the details of my Mac Pro
    thanks again
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    Mac OS X Lion 10.7.5 (11G63b)
    2 x 2.66 GHz Dual-Core Intel Xeon
    Memory 7GB 667 MHz DDR2 FB-DIMM
    Model Name:          Mac Pro
      Model Identifier:          MacPro1,1
      Processor Name:          Dual-Core Intel Xeon
      Processor Speed:          2,66 GHz
      Number of Processors:          2
      Total Number of Cores:          4
      L2 Cache (per Processor):          4 MB
      Memory:          7 GB
      Bus Speed:          1,33 GHz
      Boot ROM Version:          MP11.005D.B00
      SMC Version (system):          1.7f10
      Serial Number (system):          Not Available
      Hardware UUID:          00000000-0000-1000-8000-0017F20F9F40
    +++++++++++++++++++++++++++++++++++++++++++++++++++++
    The only HD now
    Intel ESB2 AHCI:
      Vendor:          Intel
      Product:          ESB2 AHCI
      Link Speed:          3 Gigabit
      Negotiated Link Speed:          3 Gigabit
      Description:          AHCI Version 1.10 Supported
    ST3250824AS  P:
      Capacity:          250,06 GB (250.059.350.016 bytes)
      Model:          ST3250824AS  P                         
      Revision:          3.BQK  
      Serial Number:                      9ND1P4X7
      Native Command Queuing:          Yes
      Queue Depth:          32
      Removable Media:          No
      Detachable Drive:          No
      BSD Name:          disk0
      Medium Type:          Rotational
      Bay Name:          Bay 1
      Partition Map Type:          GPT (GUID Partition Table)
      S.M.A.R.T. status:          Verified
      Volumes:
    disk0s1:
      Capacity:          209,7 MB (209.715.200 bytes)
      BSD Name:          disk0s1
      Content:          EFI
    HD INTERNO PRINCIPAL:
      Capacity:          249,2 GB (249.199.591.424 bytes)
      Available:          37,91 GB (37.914.918.912 bytes)
      Writable:          Yes
      File System:          Journaled HFS+
      BSD Name:          disk0s2
      Mount Point:          /
      Content:          Apple_HFS
    Recovery HD:
      Capacity:          650 MB (650.002.432 bytes)
      BSD Name:          disk0s3
      Content:          Apple_Boot

    NAS is of course external and depends on how you access it. And then t he ideal for RAID5 for instance woudl be WD RED series, but those do not work inside Mac tower.
    Look up "TLER"  regarding WD drives and RAID.
    Apple does not endorse or anything, not in decades and when there were problems - G5 and early adoption of SATA and changing standards and features, it was users that did the troubleshooting. 
    So unles you are using Apple's PRO RAID card, which I don't think anyone would or should and which is limited to 2TB drives and only instance of a ceiling on supported drives (it is req'd for SAS though), use your own research.

  • New hard drive in a Mac Pro - my experience.

    After taking delivery of my MacPro I was keen to add an extra hard drive to use in conjunction with amateur level video editing and photo imaging software.
    At first I bought a 3.0 Gb/s, 320 GB Seagate 7200.10. and it worked Ok but did not seem any faster than the OEM drive (250 GB Western Digital SE) . XBench confirmed that it was in fact 20% slower overall.
    I then consulted this forum and read the many posts re the Seagate firmware problem and other suggestions for suitable hard drives. To be honest it was all great stuff but, for me, a little overwhelming. So today, back went the Seagate in exchange for a 3.0 Gb/s, 250 GB, Maxtor Diamond Max 10 which was all I could afford. I installed the drive, what a dream the MacPro is, partioned it and ran XBench. The Maxtor is 2.5 to 3 times faster than the Seagate and is a quiet drive.
    So if you, like me, want a single, affordable fast and quiet drive, the Maxtor does the job. I am sure other drives are just as good if not better but if you find the research confusing, the Maxtor seems to be a safe choice.
    Also, congratulations for reading this forum before making a purchase - it saves you the 20% restocking fee for returns!

    I want to install another hard drive in my Mac Pro. Just looking for something in the 250GB or smaller range - Western Dig. Maxtor, etc.
    I see plenty of SATA 3Gbs drives - what do I look for in terms of specs. The dimensions are listed in the Mac Pro booklet, however, what type of connector is needed or not needed - seems no cables are needed... how many pins, etc.????
    Appreciate any help.

  • I had a new hard drive installed on my computer and now why does my Adobe CS4 says it is not able to install?

    Adobe CS4 says it cannot be installed on my Windows 7 after I had reinstalled a new hard drive....

    attach a screenshot of the error message (FAQ: How do I capture and post a screen shot or... | Adobe Community) if you're unable to explain the problem.

  • Installed new hard drive in a Toshiba satellite and now cant do windows upadates

    installed new hard drive in a Toshiba satellite S500-02J . Used recovery stick purchased from Toshiba. Windows installed and everything up and running, but when I go to do a windows update. I received this message: "Windows update cannot currently check for updates, because the service is not running. You may need to restart your computer."
    Toshiba help line said it was a problem because new hard drive was not exactly the same as the old hard drive. It was a minor fix but wanted a $100 to perform the fix remotely.
    Any ideas on how to fix this problem?
    Thanks.

    satellite S500-02J
    Maybe this one from the land down under?
    Satellite A500/02J (PSAR9A-02J001)
    The probloem occurs because the new drive has advanced-format technology. All the new ones do. See this message from three years ago.
    The fix is to install a new storage driver.
       Intel Rapid Storage Technology
    If you've messed around with drivers, you'll probably need to repeat the restore. Introduce the storage driver as early as possible.
    -Jerry

  • I am trying to re-install mountain lion on a new hard drive on a mac pro but get a backward slash with a circle

    I am trying to reinstall mountain lion in a mac pro with a new ssd drive but will not let me. It gives me a back slash with a circle. I have 2 optical drives, first is a blu-ray and the second is a super drive. could that be the cause?

    Firstly, you need to partition and format the SSD. You need to be able to boot the computer from another drive that has a bootable OS X system installed or a Snow Leopard DVD installer that works on the computer.
    Install Lion/Mountain Lion on a New HDD/SDD
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    Boot to the Internet Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
    Partition and Format the hard drive:
    1. Select Disk Utility from the main menu and click on the Continue button.
    2. After DU loads select your external hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Install button. Be sure to select the correct drive to use if you have more than one.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • Help! I had to have a new hard drive put in my computer and now it doesn't

    I had to replace my hard drive and then the company that did that put in windows Vista Ultimate for me and I have heard that I will lose everything that is in my Ipod since it will have to reformat itself...what can I do? I don't want to lose all my movies and music...

    Connect your iPod to your computer. If it is set to update automatically you'll get a message that it is linked to a different library and asking if you want to link to this one and replace all your songs etc, press "Cancel". Pressing "Erase and Sync" will irretrievably remove all the songs from your iPod. Your iPod should appear in the iTunes source list from where you can change the update setting to manual and use your iPod without the risk of accidentally erasing it. Also when using most of the utilities listed below your iPod needs to be enabled for disc use, changing to manual update will do this by default. Check the "manually manage music and videos" box in Summary then press the Apply button: Managing content manually on iPod
    Once you are safely connected there are a few things you can do to restore your iTunes from the iPod. If you have any iTMS purchases the transfer of purchased content from the iPod to authorised computers was introduced with iTunes 7. A paragraph on it has been added to this article: Transfer iTunes Store purchases using iPod
    The transfer of non iTMS content such as songs imported from CD is designed by default to be one way from iTunes to iPod. However there are a number of third party utilities that you can use to retrieve the music files and playlists from your iPod. You'll find that they have varying degrees of functionality and some will transfer movies, videos, photos, podcasts and games as well. Have a look at the web pages and documentation, this is just a small selection of what's available, they are generally quite straightforward. You can also read reviews of some of them here, you'll also need to check out which ones are Vista ready as the may not all be updated to be compatible yet: Wired News - Rescue Your Stranded Tunes
    TuneJack Windows Only
    iPod2PC Windows Only
    iGadget Windows Only
    iDump Windows Only
    YamiPod Mac and Windows Versions
    Music Rescue Mac & Windows
    iPodCopy Mac and Windows Versions
    There is also a manual method of accessing the iPod's hard drive and copying songs back to iTunes on Windows or a Mac. The procedure is a bit involved and won't recover playlists but if you're interested it's available at this link: Two-way Street: Moving Music Off the iPod
    Whichever of these retrieval methods you choose, keep your iPod in manual mode until you have reloaded your iTunes and you are happy with your playlists etc then it will be safe to return it auto-sync. I would also advise that you get yourself an external hard drive and back your stuff up, relying on an iPod as your sole backup is not a good idea and external drives are comparatively inexpensive these days, you can get loads of storage for a reasonable outlay.

  • I had a new hard drive put in my computer and i can not get the apps that I paid for into my new hard drive........how do I go about this?

    I need help getting back the apps that i purchased.........the app store states that they are installed but on my system they are no where to be found

    Is the Mac App Store seeing them on an external drive or partition mounted?

  • I installed a new hard drive into my macbook pro and when i transferred over iPhoto, now my iPhoto won't open

    i keep getting this error:
    Dyld Error Message:
      Library not loaded: /Library/Frameworks/iLifeFaceRecognition.framework/Versions/A/iLifeFaceRecognit ion
      Referenced from: /Applications/iPhoto.app/Contents/MacOS/iPhoto
      Reason: image not found

    To re-install iPhoto
    1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
    2a: On 10.5:  Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
    2b: On 10.6: Those receipts may be found as follows:  In the Finder use the Go menu and select Go To Folder. In the resulting window type
    /var/db/receipts/
    2c: on 10.7 they're at
    /private/var/db/receipts
    A Finder Window will open at that location and you can remove the iPhoto pkg files.
    3. Re-install.
    If you purchased an iLife Disk, then iPhoto is on it.
    If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
    If you purchased it on the App Store or have a Recent Mac you can find it in your Purchases List.

  • I have a new hard drive in my Mac Book Pro.

    Ihave a new hard drive in my MacBook Pro. Where can I get Mac OS?Unfortunately, I've got a Mac Book with outa mac os Cd.
    THX

    enter you macs serial number in the green box on this website and see what operating system it came with.  http://www.appleserialnumberinfo.com/Desktop/index.php.  You may be better off calling Apple directly and give them the serial number so they can send you the cs's for a fee.

  • New hard drive cant install mac os x

    Was having the question mark on start up problem, did everything I could and still didn't work. Ended up taking it to a mac store and they said i needed a new hard drive. Bought a new hard drive at bestbuy installed it and now Im trying to install mac os x.. my problem is that when it gets to the point that says "Select the disk where you want to install Mac OS X" there is nothing to select. Is it still not recognizing the new hard drive? If I start the computer up with out the mac os x install cd i still get the question mark with the new hard drive in. Does that mean the computer might be jacked and its not the hard drive?? Thanks

    What ds store said.................
    Hold c and boot off the OS X installer disk that came with the computer first.

  • Graphic card problem maybe? Since when I have changed the hard drive to my macbook pro and I installed all the new softwares, my mac is very slow and the screen gives crazy pictures,could maybe be the graphic card, does anybody have experienced this?

    Graphic card problem maybe? Since when I have changed the hard drive to my macbook pro and I installed all the new softwares, my mac is very slow and the screen gives crazy pictures,could maybe be the graphic card, does anybody have experienced this?

    after a restart it works for a time, but always slow. I went to the Applestore this afternoon and the made a check and said it would be the logicboard and they would have to change it for CHF 600 and it would be ready in 10 - 15 days

Maybe you are looking for

  • Late 2009 iMac 27" as display for gaming desktop?

    I'm looking at buying a gaming desktop with a high end graphics card. I know that the late 2009 imac can use the "mini-displayport" to be used as a monitor for the pc, but the graphics card on my desktop will only have a "displayport." The card comes

  • Question about sending Request for Quotation by e-mail

    Hi All, I'm trying to send our RFQ by mail, I've already customized all the settings displayed on sap note 191470 in transaction SCOT and also I've assigned the forms and messages to this document, but I still can´t get our RFQ by email to ours vendo

  • Verify error

    Hi, I am getting the following error when i try to invoke a remote method.My remote class have more than 300 methods. what is the root cause of this error and how can i rectify this error? can anyone help me on this? Ananth <Error thrown by rm i serv

  • Inventory Business Content (0IC_03)

    I have completed my work on Sandbox and am about to implement a model on the Development platform which will than be transported to QA and finally development. On the Development Box most of the objects, cubes queries etc have already been activated

  • Macbook pro-Freezes with black screen at start up.

    Macbook pro-Freezes with black screen at start up. I've tried inserting the Mac OS X install disc to run the hardware test(Restart and hold down D), But it still does nothing. Just the black screen. Now I can't get the disc out. I've tried holding do