I lost my password and cannot connect, or change the password. what can i do to change my password?

I forgot my password for my airport. i need to know how to access the system and change my password

Pay close attention to the information about a "Soft Reset" in this Apple Support Document:
http://support.apple.com/kb/HT3728?viewlocale=en_US

Similar Messages

Hi, I lost my ipad and i didn´t activit the icloud. what can i do?

Hi, I lost my ipad and i didn´t activit the icloud. what can i do?
Message was edited by: Loai og Youssef

You can't locate or do anything to your iPad if you did not activate "Find My iPad".
Read through this for things to do: http://support.apple.com/kb/ht5668

My airport is not connecting to the internet. I have a cable modem. and i'm on the internet now connected directly to the modem. what can i do?

my airport is not connecting to the internet. I have a cable modem. and i'm on the internet now connected directly to the modem. what can i do?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

All of a sudden my iphone stopped charging and you can't hear the music through my ihome iH150 when I connect it to the dock, what can I do to fix the ihome? The ihome does turn on and I already checked for dock possible problems and I don't see anything.

all of a sudden my iphone stopped charging and you can't hear the music through my ihome iH150 when I connect it to the dock, what can I do to fix the ihome? The ihome does turn on and I already checked for dock possible problems and I don't see anything wrong.

I also have to add that the right earbud only doesn't work on my phone while i'm listening to music. If I'm face timing it's okay. what the heck.

I do need help. My little i-pod appears to have lost all visuals. when I connect it to the computer I can see what is there, but I can no longer play it or see the tiy screen. Does this mean it has died? or is there a way of resucitating the poor thing. m

i do need help. My little i-pod appears to have lost all visuals. when I
connect it to the computer I can see what is there, but I can no longer
play it or see the tiy screen. Does this mean it has died? or is there a
way of resucitating the poor thing.
mk

iPod Tutorials
iPod Manuals
iPod Models

I have boxed version of iWork8 but have lost serial number and cannot activate on new computer. How can I reactivate program?

I have the disks but not the serial number. Have new mac pro laptop, but cannot access old pages and numbers files.

Doesn't the box show the serial number? Do you have your old computer with iWork on it? Then you should be able to see in the about Pages window which serial number you have.
If you have a new computer I presume you have Mountain Lion on it. You can buy Pages 09 and Numbers from the Mac AppStore and then open the documents.

TS1368 I have Windows 8 and cannot connect to my iTunes. What do I have to do? Thanks

I recently bought laptop with Windows 8. Now I can't use my iTunes on new computer. What can I do? Thanks

On Print dialog in print size choose Custom and then check the checkbox for Scale to Fit Media. With crop to fit checked if image has the same aspect ratio then it would fill the paper else would crop depending on your image dimensions.
To help you achieve more here is the Print help link for PSE - http://help.adobe.com/en_US/photoshopelements/using/WS287f927bd30d4b1f-5796c0e112e28b07616 -7fff.html
Hope it helps.
Thanks,
Garry

TS1368 Why when I want to update my apps , it said that my iPad cannot connect to iTunes Store . What can I do?

When I want to update my apps , it said that my iPad cannot connect to the iTunes Store . I don't know what happen to it . Last time I accidentally click Chang To US Store , but my own country is Malaysia . What can I do to update the apps ? Help me plssssssssss . Thankyou

Then you need to change the store that you bought the apps from - correct?
Go to the featured tab of the App Store and tap on your ID at the bottom. Tap View Apple ID. Enter your password. Go to Country/Region and change it to the correct store.

My location service is not working from the day one the response is that (cannot able to determine the location) .What can i need to do to see my location in maps and other application even the location services is enabled in the settings?

From the day one the response is that (cannot able to determine the location) while using ios5.1 .What can i need to do to see my location in maps and other application even the location services is enabled in the settings?.Which means that is there is any problem in my ipad ? currently running on IOS 6.

Your location is determined from a location database which contains the MAC addresses of routers and their physical location. A MAC address is a unique number which is built-in to all network devices when manufactured. The database is built and updated by actually driving around and mapping router locations.
Since you just moved the location of your router has not been updated in the database and when you use Maps you will see your old location.
If you go outside your house you can be correctly located because your iPod sees other routers which are in the location database. Note that you do not need to be connected to a router for your iPod to see it and obtain its MAC address.

My screen is changing colors and has lines in all the screen what can i do

I accidentally dropped my cellphone s couple of times. Then it got wet but I did not know it was wet and I connected it to my charger then my screen started to change colors and had lines covering the whole screen what can I do? I need help!

There is nothing you can do with that unit
Apple should exchange it for an Out of Warranty exchange identical 5S for $269 if you are in the US ,similar pricing elsewhere

I buy an iphone 4s sience 6 months ago and i have problems with the battery what can i do ???

i have problems with the battery of my iphone4s i have it sience february 17 of this year and i the time life of my battery i compare the lifetime of the battery of my iphone 4 with the iphone 4s and i look that the iphone 4 has long a long lifeime i can use it like 2 days without charge and whit my iphone 4s like only 12 hrs what can i do?? i have the guarrantie help me =)

Contact Apple Support. Here's how:
http://support.apple.com/kb/HE57

I have an iPhone 5 and when I'm playing music I can't change the song or start and pause on any of the shortcuts, what can I do ?

When I'm playing music and am on other things and swipe the shortcuts up, I am in able to change the song or pause and play, the same thing happens when I have locked my phone.
I have to keep unlocking my phone and going into my music to change the song, this is very frustrating!
I've gone onto settings but I am unable to find anything that will change this?
What can I do?!

I never use than switch and I had forgotten it existed but yes that was the problem.
Thank you I would have gone nuts. As they say there is no fool like an old fool.
Thanks again.
Kempsta

I just got my new iPhone 16 days ago and when I try to download an app it always give me a message "Cannot connect to ITunes Store." What can I do to fix this?

Please if anyone can help me help....

Well folks I finally got my "can't connect to iTunes" issues fixed. Seems that there was an unauthorized change to my email address and account therefore not allowing mr to connect to iTunes.
Here is how I got it fixed.
1. Contacted iTunes store support
2. Followed their instructions and replyed with the following info:
An order number from one of my purchases
Last 4 digits of the c.c. Used for the iTunes store acct
Answer to one of my security questions
And 2 items from this list.
Birthdate
Billing address for Acct
Phone number on acct
It was after all of this that they saw that someone had made an account modification back in February when the issue began. Seems they changed my email address just slightly and that is what kept me from being able to sign in and not a password issue. This was likely due to a phishing email that came out in conjunction with iCloud asking users to change their passwords to a more secure form by adding a capital and number.
To get all of this cleared up it took about 4 days as we emailed back and forth. I also needed a seperate email address they could use to send me info. Once they determined the issues and went to get them fixed by changing the email address associated with the acct and I created a new password I was able to access iTunes with no issues and even my previously thought lost acct balance was there.
Hope this helps
Crash

Internet works, but I have an exclamation mark instead of AirPort connection and cannot connect to my WiFi.. PLEASE HELP!

Internet works, but I have an exclamation mark instead of AirPort connection and cannot connect to my WiFi.. PLEASE HELP!

When you see an exclamation point in the Wi-Fi menu, from the menu bar, select
 ▹ System Preferences... ▹ Network
Click the Assist me button and select Assistant. Follow the prompts. You may get a warning that Wi-Fi is not available, that you're too far from the base station, or that you're using the wrong password.
Assuming that you've ruled out those possibilities, restart the computer and try again. If there's no change, click the lock icon in the lower left corner of the preference pane and authenticate, if necessary. From the Location menu at the top of the window, select Edit Locations. A sheet will drop down. Click the plus-sign button to create a new location. Give it any name you want. In the new location, set up the Wi-Fi service with the same settings you used before. Click Applyand test.
If there's still no connection, and if you have control of the router, compare its settings to Apple's recommendations. Some third-party routers may be incompatible in 802.11b/g/n radio mode. Try setting the mode to 802.11n only.

Exchange 2010 Send Connector to postfix (v. 2.11) smarthost uses STARTTLS and cannot connect

Dear all,
I am having problems with exchange 2010 sending emails through a postfix smarthost server which disconnects the sessions. I also use a sendmail as a smarthost
server which is working just fine but I have to switch to postfix and cannot do this as long as the encryption does not work.
Here is the log file of the postfix server:
Jan 4 14:18:59 server7 postfix/smtpd[1659]: initializing the server-side TLS engine
Jan 4 14:18:59 server7 postfix/smtpd[1659]: connect from server1.mydomain.com[192.168.20.10]
Jan 4 14:18:59 server7 postfix/smtpd[1659]: setting up TLS connection from server1.mydomain.com[192.168.20.10]
Jan 4 14:18:59 server7 postfix/smtpd[1659]: server1.mydomain.com[192.168.20.10]: TLS cipher list "aNULL:-aNULL:ALL:+RC4:@STRENGTH"
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:before/accept initialization
Jan 4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAB1B0] (11 bytes => -1 (0xFFFFFFFFFFFFFFFF))
Jan 4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAB1B0] (11 bytes => 11 (0xB))
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0000 16 03 01 00 5a 01 00 00|56 03 01 ....Z... V..
Jan 4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAB1BE] (84 bytes => 84 (0x54))
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0000 54 a9 3d b9 0d 5e 8b 64|7c 6b b5 21 f2 93 e7 84 T.=..^.d |k.!....
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0010 17 ea 33 d7 e5 13 f2 75|3a 87 38 32 01 85 82 5b ..3....u :.82...[
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0020 00 00 18 00 2f 00 35 00|05 00 0a c0 13 c0 14 c0 ..../.5. ........
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0030 09 c0 0a 00 32 00 38 00|13 00 04 01 00 00 15 ff ....2.8. ........
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0040 01 00 01 00 00 0a 00 06|00 04 00 17 00 18 00 0b ........ ........
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0050 00 02 01 ...
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0053 - <SPACES/NULLS>
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 read client hello A
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write server hello A
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write certificate A
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write key exchange A
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write server done A
Jan 4 14:18:59 server7 postfix/smtpd[1659]: write to 7F4823FA5210 [7F4823FB8B70] (1911 bytes => 1911 (0x777))
Jan 4 14:18:59 server7 postfix/smtpd[1659]: 0774 - <SPACES/NULLS>
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 flush data
Jan 4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAC803] (5 bytes => 0 (0x0))
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:failed in SSLv3 read client certificate A
Jan 4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept error from server1.mydomain.com[192.168.20.10]: lost connection
Jan 4 14:18:59 server7 postfix/smtpd[1659]: lost connection after STARTTLS from server1.mydomain.com[192.168.20.10]
Jan 4 14:18:59 server7 postfix/smtpd[1659]: disconnect from server1.mydomain.com[192.168.20.10]
I
have read in the post at https://social.technet.microsoft.com/Forums/exchange/en-US/6db38364-cb08-45c0-b159-3ddf30ef0b3e/exchange-2010-send-connector-uses-ssltls-and-cannot-connect-to-smarthost-how-to-deactivate-ssl?forum=exchange2010
how to deactivate the SSL encryption, but this is of course a security flaw, if I am not mistaken. I would like to encrypt the connection between the servers for obvious security
reasons but I have come to a standstill...
My Exchange server certificate is configured
as follows:
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAcc
ule, System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKe
essRule}
CertificateDomains : {server1, server1.solid-con.com}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=server1
NotAfter : 22/01/2017 13:18:02
NotBefore : 22/01/2012 13:18:02
PublicKeySize : 2048
RootCAType : None
SerialNumber : 6925D91285B649BD4D5E4297F1A48471
Services : IMAP, POP, IIS, SMTP
Status : Valid
Subject : CN=server1
Thumbprint : 939A37173BF84E352CEDC74F7D9A3D71F498A005
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAcc
ule, System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {WMSvc-SERVER1}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=WMSvc-SERVER1
NotAfter : 19/01/2022 12:56:44
NotBefore : 22/01/2012 12:56:44
PublicKeySize : 2048
RootCAType : Registry
SerialNumber : 1DB8711F7ADC5CB54196468EF2FF5D21
Services : None
Status : Valid
Subject : CN=WMSvc-SERVER1
Thumbprint : 191D86BDE274510453D58DDB91D253DABBCF05F1
And My Default Send Connector is configured as follows:
AddressSpaces : {SMTP:*;1}
AuthenticationCredential : System.Management.Automation.PSCredential
Comment :
ConnectedDomains : {}
ConnectionInactivityTimeOut : 00:10:00
DNSRoutingEnabled : False
DomainSecureEnabled : False
Enabled : True
ErrorPolicies : Default
ForceHELO : False
Fqdn :
HomeMTA : Microsoft MTA
HomeMtaServerId : SERVER1
Identity : Internet
IgnoreSTARTTLS : False
IsScopedConnector : False
IsSmtpConnector : True
LinkedReceiveConnector :
MaxMessageSize : unlimited
Name : Internet
Port : 25
ProtocolLoggingLevel : None
RequireOorg : False
RequireTLS : False
SmartHostAuthMechanism : None
SmartHosts : {server7.mydomain.com, server6.mydomain.com}
SmartHostsString : server7.mydomain.com,server6.mydomain.com
SmtpMaxMessagesPerConnection : 20
SourceIPAddress : 0.0.0.0
SourceRoutingGroup : Exchange Routing Group (DWBGZMFD01QNBJR)
SourceTransportServers : {SERVER1}
TlsAuthLevel :
TlsDomain :
UseExternalDNSServersEnabled : False
Any help would be greatly appreciated as I am
stuck...
Luca

Hi Allen,
Thank you very much for your reply.
The Postfix TLS Manager is enabled in master.cf
tlsmgr unix - - n 1000? 1 tlsmgr
and running
server7:/etc/postfix # ps -efa|grep tls
postfix 11967 11863 0 11:21 ? 00:00:00
tlsmgr -l -t unix -u
Every other (Linux/UNIX) server has no problem e.g.:
Jan 5 11:28:36 server7 postfix/smtpd[12215]: connect from server2.mydomain.com[192.168.20.20]
Jan 5 11:28:36 server7 postfix/smtpd[12215]: Anonymous TLS connection established from server2.mydomain.com[192.168.20.20]: TLSv1 with cipher DHE-DSS-AES256-SHA (256/256 bits)
Jan 5 11:28:36 server7 postfix/smtpd[12215]: B5502946AB0: client=server2.mydomain.com[192.168.20.20]
Jan 5 11:28:36 server7 postfix/cleanup[12221]: B5502946AB0: message-id=<[email protected]>
Jan 5 11:28:36 server7 postfix/qmgr[12200]: B5502946AB0: from=<[email protected]>, size=1026, nrcpt=1 (queue active)
Jan 5 11:28:36 server7 postfix/smtpd[12215]: disconnect from server2.mydomain.com[192.168.20.20]
Jan 5 11:28:37 server7 postfix/smtpd[12225]: connect from localhost[127.0.0.1]
Jan 5 11:28:37 server7 postfix/smtpd[12225]: 4076A946AB1: client=localhost[127.0.0.1]
Jan 5 11:28:37 server7 postfix/cleanup[12221]: 4076A946AB1: message-id=<[email protected]>
Jan 5 11:28:37 server7 postfix/qmgr[12200]: 4076A946AB1: from=<[email protected]>, size=1778, nrcpt=1 (queue active)
Jan 5 11:28:37 server7 postfix/smtpd[12225]: disconnect from localhost[127.0.0.1]
Jan 5 11:28:37 server7 postfix/smtp[12222]: B5502946AB0: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=0.54, delays=0.05/0.01/0.01/0.47, dsn=2.0.0, status=sent
(250 2.0.0 from MTA(smtp:[127.0.0.1]:10025): 250 2.0.0 Ok: queued as 4076A946AB1)
Jan 5 11:28:37 server7 postfix/qmgr[12200]: B5502946AB0: removed
Jan 5 11:28:37 server7 postfix/cleanup[12221]: 4401F946AB0: message-id=<[email protected]>
Jan 5 11:28:37 server7 postfix/qmgr[12200]: 4401F946AB0: from=<[email protected]>, size=1920, nrcpt=1 (queue active)
Jan 5 11:28:37 server7 postfix/local[12226]: 4076A946AB1: to=<[email protected]>, relay=local, delay=0.02, delays=0/0.01/0/0, dsn=2.0.0, status=sent (forwarded as 4401F946AB0)
Jan 5 11:28:37 server7 postfix/qmgr[12200]: 4076A946AB1: removed
Jan 5 11:28:37 server7 postfix/smtp[12227]: Untrusted TLS connection established to 192.168.20.10[192.168.20.10]:25: TLSv1 with cipher AES128-SHA (128/128 bits)
Jan 5 11:28:37 server7 postfix/smtp[12227]: 4401F946AB0: to=<[email protected]>, orig_to=<[email protected]>, relay=192.168.20.10[192.168.20.10]:25,
delay=0.29, delays=0/0.01/0.02/0.25, dsn=2.6.0, status=sent (250 2.6.0 <[email protected]> [InternalId=619] Queued
mail for delivery)
Jan 5 11:28:37 server7 postfix/qmgr[12200]: 4401F946AB0: removed
and if you take a look at the lines in bold you will see that mails can be delivered over TLS to that very Exchange server (the mailboxes are on that server)...
To summarise:
exchange --> postfix with TLS = session disconnected (and everything seems to be initiated by the exchange server -if I read the logs correctly)
postfix --> exchange with TLS = works
any further hints?
Thank you very much in advance,
Luca

I lost my password and cannot connect, or change the password. what can i do to change my password?

Similar Messages

Maybe you are looking for