I'm disappointed the X10 is the cell had any more bad given me so many problems like this! turns itself off and on and now does not recognize my SIM card?? help please

how i can solve these problems and how to upgrade to android 2.3

Not sure if upgrading to 2.3 will solve the problems you mentioned.
Some people are stating that after going to 2.3 their phones became unstable.
On the other hand there are many people who have gone to 2.3 and have no issues. eg myself.
If you want to go to Android 2.3, then no point in trying to solve the problems you have currently on Android 2.1
To update your phone to Android 2.3 there are 3 ways to do it. Two are official methods and one unofficial way.
Official methods.
1. Use PC Companion to perform the update.
2. SE Update service ( http://dl-www.sonyericsson.com/cws/download/1/110/61/1309763183/Update_Service_Setup-2.11.7.13.exe )
Unofficial method
Manually flash the firmware. Check out the following post
http://talk.sonyericsson.com/thread/19735

Similar Messages

My phone turned itself off and now will not turn back on!!? Help!

About 4 hours ago, I hung up after speaking to a family member and the screen went black. Apparently, it had turned itself off! Now it will not turn back on and my comp. doesn't recognize it! Help please!
iPhone 4

Also, I tried holding down the "home" and "off" at the same time and it won't turn on. please help!

Frustratingly, since I upgraded to Yosemite 10.10, I too am having the worst problems with WiFi dropping out. I've never had this problem before on my iMac 27-inch mid 2011 model. Turning WiFi off and then back on again sometimes works. Help please.

Frustratingly, since I upgraded to Yosemite 10.10, I too am having the worst problems with WiFi dropping out. I've never had this problem before on my iMac 27-inch mid 2011 model. Turning WiFi off and then back on again sometimes works. Help please. I've already tried a lot of your suggested fixes, but without success. Why hasn't Apple Fixed this?

Please test after taking each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes.
Step 1
Take the applicable steps in this support article. The Wireless Diagnostics program generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
Step 2
Disconnect all USB 3 devices. If you don't know which are USB 3, disconnect all USB devices except keyboard and mouse.
Step 3
If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. If you find that Wi-Fi works better with Bluetooth disabled, you should use the 5 GHz Wi-Fi band. Your router may not support it; in that case, you need a new router.
Step 4
Open the Energy Saver pane in System Preferences and unlock the settings, if necessary. Select the Power Adapter tab, if there is one. Uncheck the box marked
Wake for Wi-Fi network access
if it's checked.
Step 5
Open the Network pane in System Preferences and make a note of your settings in the Wi-Fi service. It may be helpful to take screenshots of the various tabs in the preference pane. If the preference pane is locked, unlock it by clicking the padlock icon and entering your administrator password. Delete Wi-Fi from the service list on the left by selecting it and clicking the minus-sign button at the bottom. Then recreate the service by clicking the plus-sign button and following the prompts.
Step 6
In the Wi-Fi settings, select
Advanced... ▹ TCP/IP ▹ Configure IPv6: Link-local
Click OK and then Apply.
Step 7
Reset the System Management Controller.
Step 8
Reset the PRAM.
Step 9
Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first.
Step 10
Make a "Genius" appointment at an Apple Store, or go to another authorized service center.

I have a ipod nano 1st and 2nd generation and am trying to put music on it but every time windows says one of the usb devices attached to this computer has malufunctioned and windows does not recognize it code 43 can someone help me please

i have a ipod nano 1st and 2nd generation and am trying to put music on it but every time windows says one of the usb devices attached to this computer has malufunctioned and windows does not recognize it code 43 can someone help me please

Try putting it into "Disk Mode" http://docs.info.apple.com/article.html?artnum=93651
Then with it in this mode connect it to the PC and try to run the latest iPod updater to do a restore and update software if you have the option. the latest iPod updater is 2006-03-23 and can be downloaded here http://www.apple.com/ipod/download/

When i attach my iphone 4 with computer it shows one of the USB devices attached to this computer has malfunctioned and windows does not recognize it,now what can i do ..plz help me

when i attach my iphone 4 with computer it shows one of the USB devices attached to this computer has malfunctioned and windows does not recognize it,now what can i do ..plz help me

I would first try unplugging All the USB devices plugged into your computer, and then plug back in just the iPhone and see if that is recognized. Also, do you have the latest version of iTunes for Windows installed on your PC, as you need to?
Hope this helps

Iphone 3gs is not charging nor detected by i tunes and computer shows 'One of the USB devices attached to this computer has malfunctioned and windows does not recognize it'

Hello evi one .. My iphone 3gs is not charging and is not recognised by itunes .whenever i attach my iphone to my computer,it displays a message 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it ' . :-( it do charging sometime with charger but does'nt by computer . kindly please tell me the solution .. thanks

As I said above, some of the new lightning cables have been known to be causing problems for some users. Have it replaced if at all possible by bringing it into your local Apple Store's Genius Bar.
B-rock

Computer says 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it'. what do i do?

i have an ipod nano 7th gen and when i plug it in for itunes my computer says 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it'. what do i do?

As I said above, some of the new lightning cables have been known to be causing problems for some users. Have it replaced if at all possible by bringing it into your local Apple Store's Genius Bar.
B-rock

One of the usb devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message.

I connected my sons Ipod Touch to my pc and it worked fine. Now, when I try to connect my iPad the following message comes up: One of the usb devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message.
I checked the cable. It surely is not the cable. If I connect the iPod again it works fine. If I use the same cable with my pc and ipad at work or my other son’s laptop, it is working perfectly. It is only on my laptop where the iPod was connected. Something tells me it got something to do with the drivers that went corrupt or something when I connected the iPod.
I searched the internet and I see a lot of people gets this message. Still no solved answers yet. Is there a place where I can download the drivers again or any other suggestions?
Windows 7 and iPad 2
Kind regards,

I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
This article was one of the ones you linked to above in your initial post
http://support.apple.com/kb/TS1369
Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears? That appears to be your situation.
Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again. If you can get it to work again initially, before doing anything else, try the following. Select the shuffle in the iTunes sidebar, under DEVICES. Over to the right, go to the Summary tab. By default, the checkbox for Enable disk use should be unchecked. If so, check it and Apply the change. See if that makes any difference.
(If Enable disk use was already checked, try unchecking it and Apply the change. Basically, set it the "other way" and see if there is any improvement.)
NOTE: When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
If the disk use change makes a difference, that may provide a clue about the actual cause.

Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message

Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message.
Using win 7 and latest iTunes [10.6.3]. Have already gone through below links and did not find any solution.
http://support.apple.com/kb/HT2292
http://support.apple.com/kb/TS1369
http://support.apple.com/kb/HT1923
http://en.kioskea.net/forum/affich-17997-ipod-not-detected

I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
This article was one of the ones you linked to above in your initial post
http://support.apple.com/kb/TS1369
Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears? That appears to be your situation.
Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again. If you can get it to work again initially, before doing anything else, try the following. Select the shuffle in the iTunes sidebar, under DEVICES. Over to the right, go to the Summary tab. By default, the checkbox for Enable disk use should be unchecked. If so, check it and Apply the change. See if that makes any difference.
(If Enable disk use was already checked, try unchecking it and Apply the change. Basically, set it the "other way" and see if there is any improvement.)
NOTE: When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
If the disk use change makes a difference, that may provide a clue about the actual cause.

Okay every time i plug my ipod up to my laptop a message comes up and says one of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. Can someone plz help me ive done everything.

I really need assistance/help with my ipod because it was working fine one day. Then the next day i decide to put more music on it then this message came up, and ive tried all the troubleshooting stuff and different links to help but still no success. But theres one thing i havent tried yet someone told me to buy another Apple charger and wall plug in to see if that works other than that i need help because i went to settings and erased everything off my ipod to see if that worked and it didnt so all my stuff is gone....Yeah i was ****** but plz help me!

I would first try unplugging All the USB devices plugged into your computer, and then plug back in just the iPhone and see if that is recognized. Also, do you have the latest version of iTunes for Windows installed on your PC, as you need to?
Hope this helps

HT201210 hi yesterday im was upgrading ios 7 in my iad butwhen its restart i turn it off and now its not working.it shows factory restore.i have done factory restore as well but after that its a same problem.can someone help me to fix that problem please

hi all
i have a ipad 2 and while im upgrading ios 7 in ipad i change my mind and i stop upgrading it,but after that when i turn it on it shows connect to itunes/i restore it but it still have a same problm,please i need your help to recover it thax

Hi Jjjames,
Thanks for posting. I'm really sorryo for the problems you've had. I can look into this for you if you wish. Drop me an email with your account details and a link to this post for reference and we'll take it from there. You'll find the address in my profile.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

I was updating my iphone in itunes, then it said the update went wrong and now does not recognize the phone. Says that it is an unknown iphone and I must restore the phone. How can I get it back without deleting all of my stuff?

I was updating my phone in itunes and the "update went wrong" and now the phone is not recognized by itunes. I unattatched the phone and it wont turn on or off, just shows a picture of the itunes symbol and a usb cord. In itunes it says that it is an unknown iphone and is in recovery mode so I need to restore the phone. If I restore the phone I loose all my pictures, which I dont want to do...and my contacts. Is there any way around this, so I can get my phone back to normal without wiping it all out? Thanks

To be more clear:
Was you phone hacked/jailbroken BEFORE you hooked it up?

Cannot sync iTouch. {"One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it."}

Any help? I have not synced the iTouch in quite a while because it could not be found after an out-of-state move. I just found it, after two years, and am wondering if it will sync if I Restore it. I don't want to lose all of my music and if there's a way to avoid that, I would appreciate it the recommendation.
jvb654

Hello jvb654,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Follow these steps, testing to see if the issue is resolved after each section.
Best of luck,
Mario

My computer will not recognize my ipod touch anymore. When I plug it in it says the USB device attached to this computer has malfunctioned and windows doesn not recognize it.

My computer (PC) will not recognize my ipod touch anymore. When I plug it in, it says the USB device attached to this computer has malfunctioned and windows does not recognize it. I have tried attaching the same cord and ipod to a different computer and it is recognized by our mac. I have tried restarting the ipod, downloading all updates on my pc, restarting the pc, etc. Nothing has worked. Please advise.

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

I forgot my password and my birthday and email does not recognize. please help me, it happen when I buy my new iphone5s and change the Apple ID of my old iPhone 4.

i have a new iPhone 5s, it does not recognize my password, when I try to restore it my birthday and email does not recognize, it only happen when I change my old iPhone 4 and change the Apple ID of it. please help me, all my phone now does not recognize my password.

To change to iCloud ID on your phone you have to go to Settings>iCloud, tap Delete Account, provide the password for the old ID then sign in with the new ID. If you don't know the password for the old ID, and if the old ID is an earlier version of your current ID, go to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Click edit next to the primary email account, change it back to your old email address and save the change. Then edit the name of the account to change it back to your old email address. You can now use your current password to turn off Find My iPhone on your device, even though it prompts you for the password for your old account ID. Then go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https://appleid.apple.com and change your primary email address and iCloud ID name back to the way it was. Now you can go to Settings>iCloud and sign in with your current iCloud ID and password.

I'm disappointed the X10 is the cell had any more bad given me so many problems like this! turns itself off and on and now does not recognize my SIM card?? help please

Similar Messages

Maybe you are looking for