I'm getting a kernel panic that I can't figure out
I have a power mac g4 1.25 with 1.5 ram. I'm getting a kernel panic that I can't figure out. I have changed the graphic card, ram, logic board, keyboard and mouse. It happens right when it starts and sometimes 5 minutes after I log in. I erased and reinstalled the operating system, and threw away the bootx file which I read could work, that didn't work. I have and older power mac g4 which has the same kind of hard drive, so I swapped them and the hard drive in the kernel panic computer work fine in the older Mac. I have tried to start up on the disc that came with the computer to do a hardware test but it wont last long enough to run the test. I have even started up in target disk mode and got a kernel panic. Also fixed disk permissions and verified the disk still no good. Did I miss something? I think it is the Processors but I would like to know for sure.
Please Help
Thank You
Kernal panics are usually caused by a hardware problem - frequently RAM or USB devices. When trying to troubleshoot problems, disconnect all external devices except your monitor, kbd & mouse. Do you experience the same problems?
May be a solution on one of these links.
Mac OS X Kernel Panic FAQ
Mac OS X Kernel Panic FAQ
Resolving Kernel Panics
12-Step Program to Isolate Freezes and/or Kernel Panics
Cheers, Tom
Similar Messages
-
My iPad says it has to restore to update, but it will not. It is caught in a cycle of not being able to restore but needed to restore. I keep getting error code 3014 but I can not figure out what this means! nor can I do anything about it! So Frutrated!
Also...
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
But... if the Device has been Modified... this will Not necessarily work. -
The vfs_fsevents.c file is kicking out errors that I can not figure out.
I get errors that I tracked back to the vfs_fsevents.c file. But I can not figure out of these are errors I need to worry about or just random. Below are the errors that I am getting.
5/9/12 12:59:12.000 PM kernel: add_fsevent: unable to get path for vp 0xdc8eafc (tmp.live.6.cmpt..mds.101.96.compactPayloads2.idx; ret 22; type 4)
5/9/12 12:59:12.000 PM kernel: add_fsevent: unabled to get a path for vp 0xdc8eafc. dropping the event.
5/9/12 12:59:12.000 PM kernel: add_fsevent: unable to get path for vp 0xdd47158 (tmp.live.6.cmpt..mds.101.95.compactPayloads1.idx; ret 22; type 4)
5/9/12 12:59:12.000 PM kernel: add_fsevent: unabled to get a path for vp 0xdd47158. dropping the event.
5/9/12 12:59:12.000 PM kernel: add_fsevent: unable to get path for vp 0x173da534 (tmp.live.6.cmpt..mds.101.97.compactPayloads1.idx; ret 22; type 4)
5/9/12 12:59:12.000 PM kernel: add_fsevent: unabled to get a path for vp 0x173da534. dropping the event.
5/9/12 12:59:12.000 PM kernel: add_fsevent: unable to get path for vp 0xbeabd7c (tmp.live.6.cmpt..mds.101.98.compactPayloads2.idx; ret 22; type 4)
5/9/12 12:59:12.000 PM kernel: add_fsevent: unabled to get a path for vp 0xbeabd7c. dropping the event.
5/9/12 1:00:51.000 PM kernel: add_fsevent: unable to get path for vp 0x17ebc280 (journalAttr.231; ret 22; type 4)
5/9/12 1:00:51.000 PM kernel: add_fsevent: unabled to get a path for vp 0x17ebc280. dropping the event.
If anyone can point me in the right direction I would appreciate it.
Thanks,
Kevin RosenthalMelissa,
Yes, I now see the WAB area. Because of the horizontal tightness of the screen cap, I missed this.
I do not have any experience with the RADEON X600, but maybe someone else knows it. My first thought would be a display driver issue with the video card. You can find out what drivers you have by following the links below. Just substitute Display Adapters for Human Interface Devices. You might go to the ATI site and see if they offer a newer driver for your video card. These get out of date in a hurry.
As for the mouse driver there are two ways to check this out:
1.) Control Panel>System>Hardware>Device Manager>Human Interface Devices>[Name of mouse and connection] Mouse Optical (if it is Optical)>Driver>Driver File Details. There, you will see all drviers associated with your mouse.
2.) From the My Computer setting, search for Intelli* in Files & Folders. This will find all instances of the IntelliPoint driver. If you have it installed, then go back and do #1 above to check to see if it is in use.
Now, all of the GUI display problems I've read of in a myriad of Adobe programs have been different, than yours. That idea is but a shot in the dark. Now, with Adobe and display issues, I normally think of Intellipoint mouse drivers. You might try changing drivers to the stock MS Windows\System32 drivers and see what happens. You might loose a touch of functionality of a multi-button/tilt-wheel mouse, if you have one, but it *might* take care of GUI issues.
I've been hoping that someone else would chime in with "hey, that's just the xxx, don't you recognize it?" So far, no one has.
Hunt -
A seemingly obvious question that I can't figure out
Ok I am usually pretty good with these things and if I don't know how to do something I ask here. However, this one seems really obvious but I can't figure it out! My problem is that I accidently hit the album art button while playing music today which brought up the previously hidden controls of shuffle song and change position. I think I've brought this up before, but this time I can't figure out how to hide these controls again. Can anyone help me please? Btw, I got the screen curtain issue figured out, though it isn't obvious what to do.
This doesn't seem to work. I have the following options, the back button, the title and artist of the track as well as the album, the album tracks button, the number in the playlist, for example 113 of 114, the shuffle and repeat buttons, then the previous, pause, and next button. When I press the album tracks button it displays the album tracks as expected and the button there changes to play view. However, it still shows the album art controls and there is no album art button now.
-
Kernel Panic that I can't get past, plus unable to start up in safemode
Hi there. I was wondering if anyone had any ideas.
I was using my computer yesterday and after dinner when I turned it on I had the transparent drapes lowering over my monitor. A kernel panic with a "You need to restart your computer" in four languages. I restarted and I get the same message. So I am sort of stuck. I can't run in safe mode. I tried and I got stuck at the apple screen with the turning gear for about half an hour.
I can use the comp as a firewire target drive. And I have run disk utilities which found a number of permissions errors that were corrected but the hard disk appears fine, and I have run the other extended hardware check - I think its what comes up when you hold down D and restart and not errors were detected.
I googled the panic log - and someone had the exact same log I think and his problem was solved by a an archive and install. The only difference is he could run in safe mode. So will this work for me? I am at work now, but have a freelance projects due in two days and need to get this machine running tonight.
Here's the log:
Sun Jan 25 22:42:18 2009
panic(cpu 1 caller 0x001694C6): "vmmapunwire: entry is unwired"@/SourceCache/xnu/xnu-1228.5.20/osfmk/vm/vm_map.c:4110
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x2edefdf8 : 0x12b0fa (0x4592a4 0x2edefe2c 0x133243 0x0)
0x2edefe48 : 0x1694c6 (0x45c20c 0x34b28000 0x0 0x2edeff0c)
0x2edeff28 : 0x5ca328 (0x34b38000 0x0 0x0 0x0)
0x2edeffc8 : 0x19ebdc (0x0 0x0 0x1a20b5 0x456b128)
Backtrace terminated-invalid frame pointer 0
Kernel loadable modules in backtrace (with dependencies):
com.apple.BootCache(30)@0x5c8000->0x5ccfff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
9E25
Kernel version:
Darwin Kernel Version 9.4.0: Mon Jun 9 19:30:53 PDT 2008; root:xnu-1228.5.20~1/RELEASE_I386
System model name: iMac8,1 (Mac-F227BEC8)
Thanks for any tips.The panic seems associated with the boot cache. This could simply be a cache corruption problem. If you can boot into safe mode, then download a utility such as TinkerTool System - VersionTracker or MacUpdate - and use it to clear all system, user, and font caches. Reboot immediately and see if this resolves your problem. If not, then you can do the following:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update. -
Messing with Class String. Error in the code that i can't figure out..
There is an error in my code that i just can't seem to figure out. I've tried debbugin it but it seems to work when i do it by hand but when running it gives me the wrong value.... I will put part of the code and comment what i'm trying to do... Basically the whole idea of that part is to get an ip address from an input but for now i will consider putting in the IP Address. It should not exceed more than 4bytes so the max is 256.256.256.256
After that i have to seperate the "." from it and take each string seperately and see if it's greater than 256 than finally copy it into an array of bytes.... Here is the code..
//CODE//
NewIPAddress = ipText.getText();// Consider this for now as "10.1.1.127"
int x=0, y=0, i=0, z=0;
boolean error=false;
String IPString;
byte[] buffer = new byte[4];
int byteVal;
do
x=NewIPAddress.indexOf(".",z);
// This should get the first occurance
// in the third round it gives the
// wrong value i dont know why....
// If there is no occurance it returns
// -1
if(x!=-1)
IPString = NewIPAddress.substring(y,(x+z));
// I get the value one
// by one 10, 1, 1 ,127
byteVal=Integer.parseInt(IPString);
buffer=(byte)byteVal;
z=z+x;
y=z+1;
i++;
if(byteVal>256)
//If each value is greater than 256 then it's
//an error
JOptionPane.showMessageDialog(null,"Not a valid IP format","Error",JOptionPane.ERROR_MESSAGE);
break;
else
error=true;
while(!error);
//CODE//
If u have a better way of doing it or if u know why the third error is please let me know, i'll appreciate that...Use a StringTokenizer (java.util.StringTokenizer) in stead, and specify '.' as the separator char:
import java.util.StringTokenizer;
public class Test
public static void main( String[] args ) throws Exception
byte[] bytes = createIpAddressArray( "10.1.1.127" );
System.out.println( "Byte 1: " + bytes[0] );
System.out.println( "Byte 2: " + bytes[1] );
System.out.println( "Byte 3: " + bytes[2] );
System.out.println( "Byte 4: " + bytes[3] );
public static byte[] createIpAddressArray( String ipAddress ) throws Exception
byte [] result = new byte[ 4 ];
StringTokenizer ipTokens = new StringTokenizer( ipAddress, "." );
int counter = 0;
while( ipTokens.hasMoreTokens() )
int ipPart = Integer.parseInt( ipTokens.nextToken() );
if( ipPart < 265 && ipPart >= 0 )
result[ counter++ ] = ( byte ) ipPart;
else
throw new Exception( "Bad IP address." );
return result; -
I'm experiencing 2 issues with a site I'm working on that I can't figure out...
I'm developing a site for a local 5-star restaurant, and I'm almost done with the development. Unfortunately, I'm a lot better at design then coding, and I have a couple of problems that I have not found solutions to.
If you have a few minutes, I'd love some advice on how to fix these. They are confusing me a lot...
1) My pages have a footer that attached to the bottom of the content of the page. On pages that end with tables, there's space between the content and the footer. On pages without tables, it looks fine. Examples:
Broken:
[1] http://www.dorseygraphics.com/review/wclg/site_05/winelist.html
Not broken:
[2] http://www.dorseygraphics.com/review/wclg/site_05/contact.html
2) My background image contains some complex elements that overlap (like vines overlapping the content area just a bit on either side). the client LOVES this, so it's not an option to remove. My background is currently a large PNG that easily takes care of the overlapping issue with a simple BG image. But it runs out at the bottom of the page, and some of the pages have content that it too tall for the background.
Example:
[3] http://www.dorseygraphics.com/review/wclg/site_05/reviews.html
How would you go about solving this problem? I'm thinking the easiest way is to add a new containing DIV and use it to extend the content area down, but that would mess up the header (I think). I'm confused.1) My pages have a footer that attached to the bottom of the content of the page. On pages that end with tables, there's space between the content and the footer. On pages without tables, it looks fine. Examples:
Broken:
[1] http://www.dorseygraphics.com/review/wclg/site_05/winelist.html
Not broken:
[2] http://www.dorseygraphics.com/review/wclg/site_05/contact.html
The problem here is the background image. Do you have the image without the beige background in the center? If so what you need to do is leave the background of the body as the URL to the image (without the beige in the center), no-repeat, and leave the color as you have. Then move the lighter beige color background to the container with the navigation and content.
2) My background image contains some complex elements that overlap (like vines overlapping the content area just a bit on either side). the client LOVES this, so it's not an option to remove. My background is currently a large PNG that easily takes care of the overlapping issue with a simple BG image. But it runs out at the bottom of the page, and some of the pages have content that it too tall for the background.
Example:
[3] http://www.dorseygraphics.com/review/wclg/site_05/reviews.html
How would you go about solving this problem? I'm thinking the easiest way is to add a new containing DIV and use it to extend the content area down, but that would mess up the header (I think). I'm confused.
If you look at my above answer I don't think this is a huge problem. In CSS3 (Safari, Firefox, Chrome, IE9) you can have multiple background images, one static and one repeating in your case. However, older browsers will not see this, most notably IE 8 and earlier. You could put the initial image in one layer and make the body background a repeating image but you run the risk of the layers not aligning.
Another alternative is to set the max-height of the content container and then set the overflow attribute to scroll in the CSS (overflow: scroll;). That would make the content container scroll independantly from the page.
A final alternative would be to discuss the pages with the client again. For instance with the wine list there are different types of wines. You could have nested tabbed panels, or you could make a page for each wine type sparkling/white, red, etc. and then have tabbed panels underneath to make the lists shorter. Otherwise the "Significant Others" or "Riesling" get lost at the bottom of the page, regardless of your background, and users do not know those wines are offered. -
just want to get a simple url when i type in the location bar, not the rest of the garbage.
== This happened ==
Every time Firefox opened
== alwaysHello Carl.
See this article:
http://support.mozilla.com/en-US/kb/Location+bar+autocomplete
I hope it helps. If it doesn't, you may be having a problem with some Firefox add-on that is hindering your Firefox's normal behavior. Have you tried disabling all add-ons (just to check), to see if Firefox goes back to normal?
Whenever you have a problem with Firefox, whatever it is, you should make sure it's not coming from one of your installed add-ons, be it an extension, a theme or a plugin. To do that easily and cleanly, run Firefox in [http://support.mozilla.com/en-US/kb/Safe+Mode safe mode] and select ''Disable all add-ons''. If the problem disappears, you know it's from an add-on. Disable them all in normal mode, and enable them one at a time until you find the source of the problem. See [http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes this article] for information about troubleshooting extensions and theme. You can troubleshoot plugins the same way.
If you want support for one of your add-ons, you'll need to contact its author. -
Email issue that I can't figure out.
I have a Gmail account and when I send messages on it from my BB the from address that the receipiant sees is a long series of code instead of my name or email address, for instance this is what it will look like to the person that receives the email...
SRS0=1jhDfa=2Q=******.com=*****@srs.bis.na.blackberry.com; on behalf of; ********** [******@******.com]
Is there a way to change this so it only shows my name or email address?is your gmail directly integrated into BIS? have you tried deleting and re-adding your gmail on BIS?
Click on KUDOS to appreciate our efforts and mark the thread RESOLVED if your issue is resolved. -
Simple actions that i can't figure out
Okay.
1. How do I tell flash to put away the items on the current
frame before going to the selected frame from the button that was
just clicked on?stephdog wrote:
> my problem is that there is a menu and obviously I don't
know which section the viewer will chose. How do I tell it to go to
the button that was just clicked after the closing animation?
This will require some variables. I will make an example for
you to help you visualize
the arrangement. The general idea is to make the path of GOTO
action dynamic so it can
be change based on user choice.
For a simple example imagine animation from frame 2 to 20.
It's the opening sequence.
Frame 21 has stop action and the content, then from 22 to 40
you have the closing part
of the animation. Right after that, frame 41 is blank, with
action to goto and play based
on the variables set with a button.
Button action basically play the timeline and define
variables in the same time.
The frame 41 assemble gotoAndPlay action to jump to the right
place.
Assuming each section is labels p1 p2 p3 and so on.
Button:
_root.pa = 1;
_root.play();
Frame 41
gotoAndPlay ("p" + _root.pa);
Another button:
_root.pa = 2;
_root.play();
etc...
Working sample:
http://www.flashfugitive.com/stuff/open_close/menu_forum_01a.swf
D/L
http://www.flashfugitive.com/stuff/open_close/menu_forum_01a.zip
Best Regards
Urami
!!!!!!! Merry Christmas !!!!!!!
<urami>
If you want to mail me - DO NOT LAUGH AT MY ADDRESS
</urami> -
I noticed my hard drive getting filled, didn't save 500 Gb of data on it. I made the observation that hidden files are been created on the Hd. I assumed they were unnecessary and deleted most of them. To my dismay am getting a kernel panic message. How do i go about getting this fixed?
Depending on what directory or directories you were erasing from you've certainly erased important system files and perhaps important applications files as well. If you have been using TimeMachine to back your computer up you should reboot into recovery mode (restart and hold Command + R until you see the Apple icon) and perform a restore.
If you haven't, boot into recovery mode anyway and choose the install OS option. Keep your fingers crossed that the OS is the only thing you deleted and that this works. You may also find it necessary to reinstall some of your software. -
I left my macbook running acquistion yesterday for about 2 hours and when I returned I could not wake it from sleep. I forced a shutdown holding the power button and now every time I turn on the macbook I am instructed to restart it, in several different languages. This screen comes up just after the "ping" when I turn it on and after the apple logo appears.
So far I have tried taking the battery out and holding the power button down for 5 seconds. Resetting the PRAM with "apple" "option" "p" and "r". Restarting in safe mode holding the "shift" key. Attempting to reboot from the instal CD disk 1 holding either the "option" key, the "x" key or the "c" key - when I do this the spinning gear appears for about 90 seconds and then reverts back to the restart kernel panic screen. I have also tried starting from the power source alone without the battery inseted. No Luck. And I ran a check of the hardware, holdig dowm the "d" key on start up with the disk inserted. No problems found.
I have no other external devices attached and I have made no modifactions to my Core 2 duo macbook that I got out of the box 3 weeks ago.
I am going to take it down to the store tomorrow unless anyone can think of a fix I have not yet tried.
Thank you for your help!Boot from your Snow Leopard DVD. If you still get the kernel panic, then you have a major hardware problem. Take it in for service.
If you can boot successfully from the Snow Leopard DVD:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Now, boot the computer into Safe Mode and operate for a while to see if the kernel panics cease. You can
Visit The XLab FAQs and read the FAQ on diagnosing kernel panics. Also, see OS X- How to log a kernel panic. Locate the panic log and post it here for us to examine.
OS X- About kernel panics -
Why do I get a kernel panic every time I unplug my g17 and use battery?
My laptop has given me fits for a longtime, so much that I usually use it more like a desktop and try never to disconnect the ac power. Every time I unplug and use the computer's battery, it works fine for a while, then eventually I get a kernel panic.
Sometimes, it's so bad, I have to force quit/restart up to 10 times for the laptop to start up again. Sometime it starts, but the screen doesn't.
I used to love this computer, now it's a pain...
Thanks.
iMac 2.1gHz Mac OS X (10.4.8)My laptop has given me fits for a longtime, so much that I usually use it more like a desktop and try never to disconnect the ac power. Every time I unplug and use the computer's battery, it works fine for a while, then eventually I get a kernel panic.
Sometimes, it's so bad, I have to force quit/restart up to 10 times for the laptop to start up again. Sometime it starts, but the screen doesn't.
I used to love this computer, now it's a pain...
Thanks.
iMac 2.1gHz Mac OS X (10.4.8) -
Can't get past kernel panics on startup
Like the title says, I'm unable to get past kernel panics on startup. I know next to nothing about the technical side of computers, so I'll just explain the whole process of what I've gone through. Earlier today I got a kernel panic after waking my computer from sleep. I restarted and everything was fine. I probably should have looked in to the cause of the panic, but I just went on using the computer as normal. Later, I returned to the computer, woke it from sleep, and got another kernel panic. I restarted, and my computer got to the Apple logo and gray spinning wheel when it froze. No kernel panic, just a frozen wheel. So I shut it down, restarted it again, and this time I got to just a gray screen (I don't remember if the Apple logo had shown up or not, but there was no spinning wheel). It hung on that screen for a while, then the fans started running like they were trying to take off a jet engine, so I shut it down. I tried restarting it once more, and it got to the spinning wheel screen when another kernel panic happened. I restarted the computer, and tried this a few more times, getting kernel panics each time. So I let it rest. A few minutes later I tried it again. This time it got even further, and I was pretty hopeful that I'd at least get the computer running again. It got past the gray spinning wheel, to the blue screen that usually shows up before the "cosmic wallpaper" and login screen. At that point it hung on that blue screen, and the jet engine sound started up. Now I take out my 10.5 instal disc. I back up with Time Machine, so I'm just going to hope reinstalling and restoring from Time Machine works out. I stick in my 10.5 disc, hold down the 'c' key and start up the iMac. Eventually it gets to the spinning wheel screen and a kernel panic. That's where I am now. Any help? I have a big paper due on Tuesday, so there's a ticking clock.
Thanks a lot
MikeHi - I have a similar problem here, running snow leopard 10.6. I am also not technical.
I went out & left my mac on, and when I got home it had switched itself off and on restart I got to the grey screen + Apple icon. Unfortunately I have never backed up my data!! Tried starting in safe mode (holding Shift key) and get the following message every time I try this:
panic (cpu 0 caller 0x560d25): "Unable to find driver for this platform: \"APCI\".n" e/SourceCache/xnu/xnu_1504.9.37/iokit/Kernel/IOPlatformExpert.cpp:1389
Debugger called:<panic>
Backtrace (CPU0),Frame : Return Address (4 potential args on stack)
BDS process name corresponding to current thread: Unknown
Mac OS version: Not yet set
Kernel Version: Darwin Kernel Version 10.7.0: Sat Jan 29 15:17:16 PST 2011; root: xnu-1504.9.37~1/RELEASE_I386
I have tried booting from the Leopard disc but can't do a repair as it doesn't seem that it can find the Mac hard disc. Have also tried starting holding the <option> key and get a Hardisc icon displayed with an arrow beneath, and when clicked a progress bar appears for maybe 30 seconds, then disappears & it just carries on in grey screen mode with spinning wheet & Apple icon.
I want to know if I just have to concede that I have lost my data and need to reinstall the OS, or it could be worth taking to a Mac repair agent to try to retrieve it -
Why, even after reinstalling everything, do I get frequent kernel panics?
I get frequent kernel panics, and nearly all of my applications crash on a regular basis.
Re-installing my system software and every application has done nothing to solve this problem.
I'm running Snow Leopard on a 7-year old intel imac.
Could this be a power supply problem?
Help!
-davidesignsHi WZZZ,
This is my log for today's events. I simply copied and pasted everything dated September 30.
Is there a better way to display this information?
It looks like multiple things are happening here:
- Suitcase Fusion is a font-management utility.
- Partition Terra is a portable Hard Drive which contains backed-up files as well as applications.
Thanks for your help,
David
11-09-30 9:48:57 AM com.apple.launchctl.Aqua[91] launchctl: Please convert the following to launchd: /etc/mach_init_per_user.d/com.adobe.SwitchBoard.monitor.plist
11-09-30 9:48:57 AM com.apple.launchd.peruser.501[89] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
11-09-30 9:48:57 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 9:48:57 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 9:49:00 AM com.apple.launchd.peruser.501[89] (com.apple.Kerberos.renew.plist[116]) Exited with exit code: 1
11-09-30 9:49:01 AM com.apple.launchd.peruser.501[89] (0x100100140.mach_init.switchboard.sh) Failed to check-in!
11-09-30 9:49:10 AM Suitcase Fusion[130] *** WARNING: Method selectedRowEnumerator in class XSOutlineView is deprecated. It will be removed in a future release and should no longer be used.
11-09-30 9:54:28 AM [0x0-0x16016].com.apple.systemevents[163] com.apple.FolderActions.enabled: Already loaded
11-09-30 9:54:31 AM AppleMobileBackup[168] WARNING: Backing up 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4
11-09-30 9:54:31 AM [0x0-0x14014].com.apple.iTunes[157] 2011-09-30 09:54:31.707 AppleMobileBackup[168:903] WARNING: Backing up 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4
11-09-30 9:54:32 AM AppleMobileBackup[168] WARNING: The existing backup does not have a success key set. Forcing a full backup by sending an empty manifest to the device.
11-09-30 9:54:32 AM [0x0-0x14014].com.apple.iTunes[157] 2011-09-30 09:54:32.132 AppleMobileBackup[168:903] WARNING: The existing backup does not have a success key set. Forcing a full backup by sending an empty manifest to the device.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 9:59:15 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 9:59:15 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 10:05:45 AM AppleMobileBackup[187] WARNING: Restoring 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4 from 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4
11-09-30 10:05:45 AM [0x0-0x14014].com.apple.iTunes[157] 2011-09-30 10:05:45.765 AppleMobileBackup[187:903] WARNING: Restoring 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4 from 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4
11-09-30 10:10:55 AM [0x0-0x14014].com.apple.iTunes[157] AppleGVA:: Error creating the accelerator 1
11-09-30 10:11:20 AM AppleMobileBackup[198] WARNING: Backing up 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4
11-09-30 10:11:20 AM [0x0-0x1e01e].com.apple.iTunes[194] 2011-09-30 10:11:20.402 AppleMobileBackup[198:903] WARNING: Backing up 4759e49c24f7dcb38799fc8d1719d7d4ad7c6da4
11-09-30 10:14:50 AM iTunes[194] This application is assuming that a particular image contains an NSBitmapImageRep, which is not a good assumption. We are instantiating a bitmap so that whatever this is keeps working, but please do not do this. Break on _NSPrivateIconImageRepSubclassAssumedToBeBitmap to debug. This will be logged only once. This may break in the future.
11-09-30 10:16:09 AM [0x0-0x1e01e].com.apple.iTunes[194] AppleGVA:: Error creating the accelerator 1
11-09-30 10:19:40 AM com.apple.WindowServer[64] Fri Sep 30 10:19:40 david-youngs-computer.local WindowServer[64] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
11-09-30 10:43:59 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 10:43:59 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 10:51:39 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 10:51:39 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 10:58:34 AM Suitcase Fusion[130] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x47bb70> '(null)') unlocked from thread which did not lock it
11-09-30 10:58:34 AM Suitcase Fusion[130] *** Break on _NSLockError() to debug.
11-09-30 11:00:29 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 11:00:29 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 11:01:01 AM com.apple.launchd.peruser.501[89] ([0x0-0x22022].com.apple.Safari[226]) Exited: Killed
11-09-30 11:01:01 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.enabled[123]) Exited: Killed
11-09-30 11:01:01 AM com.apple.launchd.peruser.501[89] (com.apple.AirPortBaseStationAgent[118]) Exited: Killed
11-09-30 11:01:01 AM imagent[121] Unable to create APS daemon connection: (ipc/mig) server died
11-09-30 11:01:01 AM imagent[121] Unable to set enabled topics: (ipc/send) invalid destination port
11-09-30 11:01:15 AM com.apple.launchd[1] *** launchd[1] has started up. ***
11-09-30 11:01:35 AM com.apple.launchctl.Aqua[88] launchctl: Please convert the following to launchd: /etc/mach_init_per_user.d/com.adobe.SwitchBoard.monitor.plist
11-09-30 11:01:35 AM com.apple.launchd.peruser.501[86] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
11-09-30 11:01:35 AM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 11:01:35 AM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 11:01:38 AM com.apple.launchd.peruser.501[86] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[11 8]) posix_spawn("/Volumes/PARTITION - TERRA_1 /Applications/Adobe Reader.app/Contents/MacOS/Updater/Adobe Reader Updater Helper.app/Contents/MacOS/Adobe Reader Updater Helper", ...): No such file or directory
11-09-30 11:01:38 AM com.apple.launchd.peruser.501[86] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[11 8]) Exited with exit code: 1
11-09-30 11:01:38 AM com.apple.launchd.peruser.501[86] (com.apple.Kerberos.renew.plist[109]) Exited with exit code: 1
11-09-30 11:01:38 AM com.apple.launchd.peruser.501[86] (0x100100140.mach_init.switchboard.sh) Failed to check-in!
11-09-30 11:01:39 AM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 11:01:39 AM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 11:01:42 AM Suitcase Fusion[125] *** WARNING: Method selectedRowEnumerator in class XSOutlineView is deprecated. It will be removed in a future release and should no longer be used.
11-09-30 11:06:21 AM com.apple.WindowServer[65] Fri Sep 30 11:06:21 david-youngs-computer.local WindowServer[65] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
11-09-30 11:06:23 AM com.apple.launchd.peruser.501[86] (com.apple.AirPortBaseStationAgent[111]) Exited: Killed
11-09-30 11:06:23 AM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.enabled[116]) Exited: Killed
11-09-30 11:06:23 AM imagent[114] Unable to create APS daemon connection: (ipc/mig) server died
11-09-30 11:06:23 AM imagent[114] Unable to set enabled topics: (ipc/send) invalid destination port
11-09-30 11:36:02 AM com.apple.launchd[1] *** launchd[1] has started up. ***
11-09-30 11:36:23 AM com.apple.launchctl.Aqua[91] launchctl: Please convert the following to launchd: /etc/mach_init_per_user.d/com.adobe.SwitchBoard.monitor.plist
11-09-30 11:36:23 AM com.apple.launchd.peruser.501[89] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
11-09-30 11:36:23 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 11:36:23 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 11:36:24 AM com.apple.launchd.peruser.501[89] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[12 1]) posix_spawn("/Volumes/PARTITION - TERRA_1 /Applications/Adobe Reader.app/Contents/MacOS/Updater/Adobe Reader Updater Helper.app/Contents/MacOS/Adobe Reader Updater Helper", ...): No such file or directory
11-09-30 11:36:24 AM com.apple.launchd.peruser.501[89] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[12 1]) Exited with exit code: 1
11-09-30 11:36:25 AM com.apple.launchd.peruser.501[89] (com.apple.Kerberos.renew.plist[112]) Exited with exit code: 1
11-09-30 11:36:25 AM com.apple.launchd.peruser.501[89] (0x100100140.mach_init.switchboard.sh) Failed to check-in!
11-09-30 11:36:25 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 11:36:25 AM com.apple.launchd.peruser.501[89] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 11:36:28 AM Suitcase Fusion[128] *** WARNING: Method selectedRowEnumerator in class XSOutlineView is deprecated. It will be removed in a future release and should no longer be used.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 11:36:45 AM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 11:36:45 AM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 1:20:12 PM mdworker[219] CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary.
11-09-30 1:20:15 PM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 1:20:15 PM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 1:20:15 PM Suitcase Fusion[128] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x43fb70> '(null)') unlocked from thread which did not lock it
11-09-30 1:20:15 PM Suitcase Fusion[128] *** Break on _NSLockError() to debug.
11-09-30 1:23:06 PM com.apple.WindowServer[68] Fri Sep 30 13:23:06 david-youngs-computer.local WindowServer[68] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
11-09-30 1:23:10 PM [0x0-0x2b02b].com.adobe.Photoshop[248] ScriptUI: 1[0]: 1.652390 (FlexServer performance info) 0.500 seconds to load /Applications/Adobe Photoshop CS5/Plug-Ins/Extensions/ScriptingSupport.plugin/Contents/Resources
11-09-30 1:23:11 PM [0x0-0x2b02b].com.adobe.Photoshop[248] ScriptUI: 3[0]: 2.022770 (FlexServer performance info) 0.350 seconds for server SWF to initialize
11-09-30 1:23:11 PM [0x0-0x2b02b].com.adobe.Photoshop[248] ScriptUI: 6[0]: 2.100784 (FlexServer performance info) 0.100 seconds to load /Applications/Adobe%20Photoshop%20CS5/Plug-Ins/Extensions/ScriptingSupport.plug in/Contents/Resources/ScriptUIFlexPhotoshop.swf
11-09-30 2:02:00 PM mdworker[325] CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary.
11-09-30 2:02:46 PM com.apple.launchd.peruser.501[89] (com.apple.Finder[95]) Exited: Terminated
11-09-30 2:02:46 PM loginwindow[35] *** -[NSCFArray objectAtIndex:]: index (2) beyond bounds (2)
11-09-30 2:02:46 PM com.apple.loginwindow[35] 2011-09-30 14:02:46.554 loginwindow[35:107] *** -[NSCFArray objectAtIndex:]: index (2) beyond bounds (2)
11-09-30 2:10:05 PM com.apple.launchd[1] *** launchd[1] has started up. ***
11-09-30 2:10:30 PM com.apple.launchctl.Aqua[86] launchctl: Please convert the following to launchd: /etc/mach_init_per_user.d/com.adobe.SwitchBoard.monitor.plist
11-09-30 2:10:30 PM com.apple.launchd.peruser.501[84] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
11-09-30 2:10:30 PM com.apple.launchd.peruser.501[84] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 2:10:30 PM com.apple.launchd.peruser.501[84] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 2:10:33 PM com.apple.launchd.peruser.501[84] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[11 7]) posix_spawn("/Volumes/PARTITION - TERRA_1 /Applications/Adobe Reader.app/Contents/MacOS/Updater/Adobe Reader Updater Helper.app/Contents/MacOS/Adobe Reader Updater Helper", ...): No such file or directory
11-09-30 2:10:33 PM com.apple.launchd.peruser.501[84] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[11 7]) Exited with exit code: 1
11-09-30 2:10:33 PM com.apple.launchd.peruser.501[84] (com.apple.Kerberos.renew.plist[108]) Exited with exit code: 1
11-09-30 2:10:33 PM com.apple.launchd.peruser.501[84] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 2:10:33 PM com.apple.launchd.peruser.501[84] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 2:10:34 PM com.apple.launchd.peruser.501[84] (0x100203570.mach_init.switchboard.sh) Failed to check-in!
11-09-30 2:10:39 PM Suitcase Fusion[122] *** WARNING: Method selectedRowEnumerator in class XSOutlineView is deprecated. It will be removed in a future release and should no longer be used.
11-09-30 2:15:07 PM mdworker[154] CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary.
11-09-30 2:19:12 PM Suitcase Fusion[122] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x1935050> '(null)') unlocked from thread which did not lock it
11-09-30 2:19:12 PM Suitcase Fusion[122] *** Break on _NSLockError() to debug.
11-09-30 2:19:15 PM ReportCrash[160] Saved crash report for WebProcess[143] version 6534 (6534.50) to /Users/davidyoung/Library/Logs/DiagnosticReports/WebProcess_2011-09-30-141915_d avid-youngs-computer.crash
11-09-30 2:31:39 PM Suitcase Fusion[122] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x1935050> '(null)') unlocked from thread which did not lock it
11-09-30 2:31:39 PM Suitcase Fusion[122] *** Break on _NSLockError() to debug.
11-09-30 2:34:07 PM PluginProcess[172] Process manager already initialized -- can't fully enable headless mode.
11-09-30 2:34:07 PM [0x0-0x12012].com.apple.Safari[141] 2011-09-30 14:34:07.261 PluginProcess[172:903] Process manager already initialized -- can't fully enable headless mode.
11-09-30 2:35:19 PM com.apple.WindowServer[65] Fri Sep 30 14:35:19 david-youngs-computer.local WindowServer[65] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
11-09-30 2:35:20 PM com.apple.launchd.peruser.501[84] (com.apple.AirPortBaseStationAgent[110]) Exited: Killed
11-09-30 2:35:20 PM com.apple.launchd.peruser.501[84] (com.apple.FolderActions.enabled[115]) Exited: Killed
11-09-30 2:35:21 PM imagent[113] Unable to create APS daemon connection: (ipc/mig) server died
11-09-30 2:35:21 PM imagent[113] Unable to set enabled topics: (ipc/send) invalid destination port
11-09-30 2:45:56 PM com.apple.launchd[1] *** launchd[1] has started up. ***
11-09-30 2:46:20 PM com.apple.launchctl.Aqua[88] launchctl: Please convert the following to launchd: /etc/mach_init_per_user.d/com.adobe.SwitchBoard.monitor.plist
11-09-30 2:46:20 PM com.apple.launchd.peruser.501[86] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
11-09-30 2:46:20 PM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 2:46:20 PM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 2:46:21 PM com.apple.launchd.peruser.501[86] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[11 9]) posix_spawn("/Volumes/PARTITION - TERRA_1 /Applications/Adobe Reader.app/Contents/MacOS/Updater/Adobe Reader Updater Helper.app/Contents/MacOS/Adobe Reader Updater Helper", ...): No such file or directory
11-09-30 2:46:21 PM com.apple.launchd.peruser.501[86] (com.adobe.ARM.321567600e43b68b05622a8adfd1fb8abccf0d5cec274b355d75ce29[11 9]) Exited with exit code: 1
11-09-30 2:46:22 PM com.apple.launchd.peruser.501[86] (com.apple.Kerberos.renew.plist[110]) Exited with exit code: 1
11-09-30 2:46:22 PM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Bug: launchd_core_logic.c:4598 (24498):2
11-09-30 2:46:22 PM com.apple.launchd.peruser.501[86] (com.apple.FolderActions.folders) Path monitoring failed on "/Volumes/PARTITION - TERRA_1 /Applications": No such file or directory
11-09-30 2:46:22 PM com.apple.launchd.peruser.501[86] (0x100402be0.mach_init.switchboard.sh) Failed to check-in!
11-09-30 2:46:26 PM Suitcase Fusion[124] *** WARNING: Method selectedRowEnumerator in class XSOutlineView is deprecated. It will be removed in a future release and should no longer be used.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
11-09-30 2:46:48 PM Suitcase Fusion[124] *** -[NSConditionLock unlock]: lock (<NSConditionLock: 0x104d340> '(null)') unlocked from thread which did not lock it
11-09-30 2:46:48 PM Suitcase Fusion[124] *** Break on _NSLockError() to debug.
Maybe you are looking for
-
Planned order to Purchase Req. Conversion
Hi, I have a planned order dated June. When will this be converted to a Purchase Requisition?? based on Planned delivery time and GR processing time?? Kindly clarify TIA Sabitha
-
IDVD Slide Show Feature - Audio Issues
Looked around in this forum and did not see this specific issue. I open iDVD, pick a theme, add a slide show, select the pictures out of the media window, and drag them in. Select a play list out of iTunes, and drag it in. Play the show in iDVD, all
-
CHANGES MADE IN ECC NOT GETTING REPLICATED TO CRM - CUSTOMER
Hi All We are currently working on CRM 4.0 connected to ECC 4.6C. All the middleware connectivity have been configured and we have a process of creating customers (BP) in CRM which inturn flows to R/3. We dont create customers in R/3 system. Now w
-
[JS or AS] Applying Paragraph Styles.
Hi, I have a JavaScript From Dave Saunders. Which Takes a list of all Para and Character styles from an InDesign File and make a .txt file. Which works great. So because I don't understand JavaScript and Very Basic Applescript. I have made a basic Ap
-
OSB XSLT Transform in Service Orchestration
I am trying to use the function op:subtract-dayTimeDuration-from-dateTime within a stylesheet within a stage in the OSB. Is it possible to use this function in a stylesheet? I get an error after using the test console to test the XSLT resource: Error