I'm getting signal leakage between channels on my 6062E
I'm getting signal leakage between channels on my 6062E. I'm using a 6062E with a SCB-68 connector block and a SHC68-68-EP cable. If I connect to just channel 1 but monitor channels 2 and 3 (haven't looked at any others) I'm picking up the signal in all three channels? Is this due to the cable I am using?
cheers
Jon
Jon,
This is expected behavior, you do not have a problem with cables or the connection block. If you don't want the channels to rail high (open circuit) with cross talk you will need to tie them down to ground using a 1K resistor (please see any of the DAQ card user manuals).
Kind regards
Joe
NI-UK
Similar Messages
-
How can I insert a code to switch between channels?
I’ve got a HP4263A LCR meter which is being used with an ER-18 device to get multiple channel data acquisition, when I go to getting started to trigger the device, but this VI do not have an icon to change the channel how can I insert a code to switch between channels?
I am just trying to use the drivers developed by NI for this device, but I don't know how to work on them to obtain data from three points, or three channels which I am using from an ER-16 device. So all what I have is the driver VI for the HP4263A.the only VI I can use is getting started, because whe I try to run any other one, this message appears:
Error -1073807346 occurred at VISA Write in HP4263A Self-Test.vi.
Possible reasons:
VISA: (Hex 0xBFFF000E) The given session or object reference is invalid.
your help would be very helpful
thanks -
Generating signal at particular channel of a connector in 7851 R-Series
I am trying to generate analog sinusodial signal at particular channel in connector 0 of 7851 R-series. I have created fpga vi and host vi and trying to send the signal to AO0. I am giving a simulated signal in host vi to the AO0 channel and trying to see at the physical port of terminal box of AO0 channel through oscilloscope. But I am not getting any signal there. But it is working fine for digital signal. Kindly give your suggestion where I am going wrong.
Thank you,
SuvenduHello,
There are two things that I would do. First submit your project so that we can see what your code is doing and possibly spot any errors.
The second thing would be to check what hardware you are outputing too. Do you have some connector box? What cable are you connecting from your connector box to your fpga card at port 0? Is it an MIO cable or a DIO cable? if you have a DIO cable like the SHC68-68-RDIO then you won't be able to do analog input/output. If you have a SHC68-68-RMIO, then you will.
Regards,
Andrew
National Instruments
RIO Embedded Hardware PSE
CompactRIO Developers Guide -
How do I get signal from my Roland Fantom G8 to Logic Studio or GarageBand?
My computer recently crashed, and since then I have not been able to record any music into either Logic Studio or GarageBand. I need to get back up and running ASAP, as I'm in the middle of recording music for 5 different projects. Here's all the gear that I have:
-1 Roland Fantom G8
-1 iMac with Logic Studio and GarageBand
-1 M-Audio Fast Track Ultra
-2 Rokit KRK Monitors
-1 USB cable
-1 midi cable
-2 1/4-inch cables
-2 1/4-in to XLR cables
The 2 1/4-inch cables run from Balanced Outputs 1 and 2 on the back on the Fantom G8 into Inputs 1 and 2 on the back of the Fast Track Ultra. The 2 1/4-inch to XLR cables run from the back of the 2 KRK monitors into Outputs 1 and 2 on the back of the Fast Track Ultra. The Fast Track Ultra is powered via USB cable that runs into a USB port on the back of my iMac. The midi cable runs from the "Computer" port on the back of the Fantom G8 into a USB port on the back of my iMac. This is the exact set-up I had before my computer crashed, and I was able to record just fine. When I open up the audio preferences on either Logic Studio or GarageBand now, it recognizes the Fast Track Ultra; however, it does not recognize the Fantom G8. What I'm trying to do is get signal from my Fantom G8 into both Logic Studio and GarageBand. I also want that sound to then project through my KRK monitors. I also want to be able to record audio and midi. Please help me!!!I used the Fantom for several years and did exactly what you want to do. I simply plugged my Fantom into a channel on my mixer, in your case the 003. I ran a firewire out of my mixer (Presonus Studio Live) into my computer using Logic Pro X. Then I just assigned that incoming channel to a channel strip in Logic. As an example I used stero channel 9/10 on my mixer, (plugged in the Fantom here). Then the signal went via my mixer firewire to computer running Logic. I assigned my channel strip input to channel 9/10.
Does this make sense?
I just sold my Fantom last week and purchased a new Yamaha Motif XF8. Now I am trying to figure out the same thing on it. -
I can not count the data from the module. Can prompt as it to make. It is desirable with examples (data read-out from the module and data transmission between channels. It is in advance grateful.
Hello. Most of the engineers in developer exchange are more familiar
with NI products. Contacting ICS for technical support is a better
course of action. -
I have a carillon 25 keyboard (bad choice, I know) and I can't get it to communicate with my mac at all! I'm running logic pro 9 and reason 5. I get signal in from my M Audio trigger finger so I know it isnt an entirely mac based problem. Thanks!!!
Well, how have to determined no signal is being recieved to your mac?
Have you got something that shows the actual signal? Or have you just been trying to control a VST? What software are you using by the way?
I personnally went with a AKAI MPK25, because it's made already mapped for logic & ableton etc, so it just makes things incredibly easy.
I would suggest you return it if you can as a dead unit & perhaps look at something else a bit easier?
Otherwise, if you just want to get this working we can have a look a bit deeper.
And driver? OS X driver? -
How to get the link between mara, ausp, cawn and cawnt tables
hello ABAPERS
i have got a requiremet in that i have to get the relation .
how to get the link between mara, ausp, cawn and cawnt tables and also type how can we get link between char value and char description in cawn and cawnt tables through ausp and mara tables.
I would be very thankful for ur help in advance.
Thanks & Regards.
soniHi,
Sample report using the linkage between tables;
report batch_char no standard page heading
line-size 132
line-count 58(1)
message-id mm.
Report by Batch Characteristic *
Description : Report by Batch Characteristic *
Declaration for Tables
tables: mara, " Material Master
mard, " Storage Location Data for Material
t001w, " Plants/Branches
t001l, " Storage Locations
cabn, " Characteristics
inob. " Link between Internal Number and Object
Declaration for Constants
constants : c_klart like ausp-klart value '023', " Class Type
c_obtab like inob-obtab value 'MCH1', " Database Table
c_flag type c value 'X', " Flag
c_c23 type i value '23', " Ratio
Constants for Ratio Categories
c_13 type p decimals 2 value '13.00', " For Ratio 13
c_1499 type p decimals 2 value '14.99', " For Ratio 14.99
c_15 type p decimals 2 value '15.00', " For Ratio 15
c_1699 type p decimals 2 value '16.99', " For Ratio 16.99
c_17 type p decimals 2 value '17.00', " For Ratio 17
c_1899 type p decimals 2 value '18.99', " For Ratio 18.99
c_19 type p decimals 2 value '19.00', " For Ratio 19
c_2099 type p decimals 2 value '20.99', " For Ratio 20.99
c_21 type p decimals 2 value '21.00', " For Ratio 21
c_2299 type p decimals 2 value '22.99', " For Ratio 22.99
c_23 type p decimals 2 value '23.00', " For Ratio 23
c_g23(4) type c value '>=23', " For Ratio >=23
c_ratio(5) value 'RATIO', " For Ratio
Constants for Storing Selected item field information
c_cursor1(15) value 'I_OUTPUT1-MEINS', " For Selected Base
" Unit of Measure
c_cursor2(15) value 'I_OUTPUT1-MATNR', " For Selected Base
" Material Number
c_cursor3(15) value 'I_OUTPUT1-MAKTX', " For Selected Base
" Material Des.
c_cursor4(15) value 'I_OUTPUT1-CLABS', "For Selected Base
" Stock Value
c_cursor5(15) value 'I_OUTPUT1-ATFLV', " For Selected Base
" Char.Value (Ratio)
c_cursor6(5) value 'C_G23'.
Declaration for Global Variables
data : g_exit type c, " Flag
g_clabs1(16) type c, " Quantity
g_clabs(18) type c, " Quantity
g_cursor(15) type c, " Cursor field name
g_matnr type mara-matnr, " Material Number
g_werks type mchb-werks, " Plant
g_atinn(30) type c. " Character.
Declaration for Internal tables
Internal table to hold Batch Stock data
data : begin of i_mchb occurs 0,
matnr like mchb-matnr, " Material Number
werks like mchb-werks, " Plant
lgort like mchb-lgort, " Storage Location
charg like mchb-charg, " Batch Number
clabs like mchb-clabs, " Stock Value
meins like mara-meins, " Unit of measure
atflo like ausp-atflv, " Char.Value (Ratio)
atflv like ausp-atflv, " Char.Value (Ratio)
end of i_mchb.
Internal table to hold Secondary List data
data : begin of i_mchb1 occurs 0,
werks like mchb-werks, " Plant
matnr like mchb-matnr, " Material Number
lgort like mchb-lgort, " Storage Location
charg like mchb-charg, " Batch Number
atinn like ausp-atinn, " Char.Value
clabs like mchb-clabs, " Stock Value
atflo like ausp-atflv, " Char.Value (Ratio)
atflv like ausp-atflv, " Char.Value (Ratio)
end of i_mchb1.
Internal table to get the Plant Name
data : begin of i_plant occurs 0,
werks like t001w-werks, " Plant
name1 like t001w-name1, " Name
end of i_plant.
Internal table to get the Material Description
data : begin of i_makt occurs 0,
matnr like makt-matnr, " Material
maktx like makt-maktx, " Description
end of i_makt.
Internal table to hold AUSP data
data : begin of i_ausp occurs 0,
objek like ausp-objek, " Object No
atinn like cabn-atinn, " Characteric value
atflv like ausp-atflv, " Characteristic Value
end of i_ausp.
Internal table to hold output data
data : begin of i_output occurs 0,
atinn like cabn-atinn, " Characteric value
werks like mchb-werks, " Plant
matnr like mchb-matnr, " Material Number
atnam like cabn-atnam, " Characteristic
atflv like ausp-atflv, " Char.Value (Ratio)
name1 like t001w-name1, " Plant Description
maktx like makt-maktx, " Material Description
clabs like mchb-clabs, " Stock Value
meins like mara-meins, " Base Unit of Measure
end of i_output.
Internal table to hold final Output data
data : begin of i_output1 occurs 0,
atinn like cabn-atinn, " Characteric value
werks like mchb-werks, " Plant
matnr like mchb-matnr, " Material Number
atnam like cabn-atnam, " Characteristic
atflv(32) type c, " Char.Value (Ratio)
name1 like t001w-name1, " Plant Description
maktx like makt-maktx, " Material Description
clabs like mchb-clabs, " Stock Value
meins like mara-meins, " Base Unit of Measure
end of i_output1.
Selection screen
selection-screen begin of block b1 with frame title text-001.
select-options: s_werks for t001w-werks obligatory, " Plant
s_lgort for t001l-lgort, " Stor.Location
s_matnr for mara-matnr obligatory, " Material No
s_atinn for cabn-atinn. " Character.
selection-screen end of block b1.
At selection screen
at selection-screen.
Validation of Selection Screen Fields
perform validate_screen.
Start of selection
start-of-selection.
Get the Material and Batch Stock data from MARA and MCHB Tables
perform get_mat_stock_data.
Get the Material Group Text and Plant Name from T023T and T001W Tables
perform get_plant_grp_data.
Append the data into final Output Internal Table after getting the
Characteristic Values data from INOB and AUSP Tables
perform append_final_data.
Processing if the Characteristics contain 'RATIO'
perform collect_ratio.
End-of-Page
end-of-page.
write /1(125) sy-uline.
End of selection
end-of-selection.
if g_exit <> c_flag.
Display the Report Output data
perform display_report.
endif.
Top-of-Page
top-of-page.
Write the Report and Column Headings
perform get_headings.
at line-selection
at line-selection.
if sy-lsind = 1.
perform display_batch.
endif.
Top of page during line-selection
top-of-page during line-selection.
perform heading_seclist.
Form validate_screen
Validation of Selection Screen fields
form validate_screen.
Validation of Plant
clear t001w.
if not s_werks[] is initial.
select werks
into t001w-werks
from t001w
up to 1 rows
where werks in s_werks.
endselect.
if sy-subrc <> 0.
message e899 with 'Enter Valid Plant'(002).
endif.
endif.
Validation of Material Number
clear mara.
if not s_matnr[] is initial.
select matnr
into mara-matnr
from mara
up to 1 rows
where matnr in s_matnr.
endselect.
if sy-subrc <> 0.
message e899 with 'Enter Valid Material'(003).
endif.
endif.
Validation of Storage Location
clear t001l.
if not s_lgort[] is initial.
select lgort
into t001l-lgort
from t001l
up to 1 rows
where lgort in s_lgort.
endselect.
if sy-subrc <> 0.
message e899 with 'Enter Valid Storage Location'(004).
endif.
endif.
Validation of Characteristic Value
clear cabn.
if not s_atinn[] is initial.
select atinn
into cabn-atinn
from cabn
up to 1 rows
where atinn in s_atinn.
endselect.
if sy-subrc <> 0.
message e899 with 'Enter Valid Characteristic Value'(005).
endif.
endif.
Validation of Plant, Material and Storage Location
clear mard.
select matnr werks lgort
into (mard-matnr, mard-werks, mard-lgort)
from mard
up to 1 rows
where matnr in s_matnr and
werks in s_werks and
lgort in s_lgort.
endselect.
if sy-subrc <> 0.
message e899 with 'No Data found for the Selection Criteria'(006).
endif.
endform. "validate_screen
*& Form get_headings
Write the Report and Column Headings
form get_headings.
data: l_repid type sy-repid.
l_repid = sy-repid.
call function 'Y_STANDARD_HEADING'
exporting
repid = l_repid
heading1 = sy-title.
write:/1(125) sy-uline.
format color col_heading on.
write : /1 sy-vline, 2(18) 'Material Number'(008) centered,
20 sy-vline, 21(40) 'Material Description'(011) centered,
61 sy-vline, 62(22) 'Ratio'(009) centered,
84 sy-vline, 85(18) 'Quantity'(010) centered,
103 sy-vline, 104(20) 'Base Unit of Measure'(015) centered,
125 sy-vline.
write:/1(125) sy-uline.
format color off.
endform. "get_headings
*& Form get_mat_stock_data
Get the Material and Batch Stock data from MARA and MCHB Tables
form get_mat_stock_data.
clear: i_mchb,i_output, i_output1.
refresh: i_mchb,i_output, i_output1.
select a~matnr " Material Number
b~werks " Plant
b~lgort " Storage Location
b~charg " Batch Number
b~clabs " Stock Value
a~meins " Base Unit of Measure
into table i_mchb
from mara as a inner join mchb as b
on amatnr eq bmatnr
where b~matnr in s_matnr and
b~werks in s_werks and
b~lgort in s_lgort.
if sy-subrc <> 0.
g_exit = c_flag.
message s899 with 'No Data found for the Selection Criteria'(006).
stop.
endif.
sort i_mchb by matnr werks lgort charg.
endform. " get_mat_stock_data
*& Form get_plant_grp_data
Get the Material Group Text and Plant Name from T023T and T001W
form get_plant_grp_data.
if not i_mchb[] is initial.
Get the Plant Description from t001w Table
clear i_plant.
refresh i_plant.
select werks " Plant
name1 " Name
into table i_plant
from t001w
for all entries in i_mchb
where werks = i_mchb-werks.
Get the Material Description from MAKT Table
clear i_makt.
refresh i_makt.
select matnr " Material number
maktx " Material Description
into table i_makt
from makt
for all entries in i_mchb
where matnr = i_mchb-matnr and
spras = sy-langu.
sort i_plant by werks.
delete adjacent duplicates from i_plant comparing werks.
sort i_makt by matnr.
delete adjacent duplicates from i_makt comparing matnr.
endif.
endform. "form get_plant_grp_data.
*& Form append_final_data
Append the data into final Internal Table
form append_final_data.
data : l_matbatch(28),
l_tabix like sy-tabix.
if not i_mchb[] is initial.
loop at i_mchb.
l_tabix = sy-tabix.
clear l_matbatch.
concatenate i_mchb-matnr i_mchb-charg into l_matbatch.
move-corresponding i_mchb to i_output.
Get the Plant Description from i_plant Table
read table i_plant with key werks = i_mchb-werks binary search.
if sy-subrc = 0.
i_output-name1 = i_plant-name1.
endif.
Get the Material Description from i_makt Table
read table i_makt with key matnr = i_mchb-matnr binary search.
if sy-subrc = 0.
i_output-maktx = i_makt-maktx.
endif.
Get the Characteristic Values data from INOB and AUSP Tables
clear inob.
select single cuobj from inob
into inob-cuobj
where klart = c_klart and
obtab = c_obtab and
objek = l_matbatch.
if sy-subrc = 0.
select objek
atinn
atflv
from ausp
into table i_ausp
where objek = inob-cuobj and
atinn in s_atinn and
klart = c_klart.
sort i_ausp by objek atinn.
loop at i_ausp.
clear cabn.
select single atinn atnam from cabn
into (cabn-atinn,cabn-atnam)
where atinn = i_ausp-atinn.
if sy-subrc = 0.
If the ratio value is between 13-14.99, display 13
if cabn-atnam cs c_ratio.
if i_ausp-atflv between c_13 and c_1499.
i_mchb-atflo = i_ausp-atflv.
i_mchb-atflv = c_13.
If the ratio value is between 15-16.99, display 15
elseif i_ausp-atflv between c_15 and c_1699.
i_mchb-atflo = i_ausp-atflv.
i_mchb-atflv = c_15.
If the ratio value is between 17-18.99, display 17
elseif i_ausp-atflv between c_17 and c_1899.
i_mchb-atflo = i_ausp-atflv.
i_mchb-atflv = c_17.
If the ratio value is between 19-20.99, display 19
elseif i_ausp-atflv between c_19 and c_2099.
i_mchb-atflo = i_ausp-atflv.
i_mchb-atflv = c_19.
If the ratio value is between 21-22.99, display 21
elseif i_ausp-atflv between c_21 and c_2299.
i_mchb-atflo = i_ausp-atflv.
i_mchb-atflv = c_21.
If the ratio value is greater than or equal to 23, display 23
elseif i_ausp-atflv >= c_23.
i_mchb-atflo = i_ausp-atflv.
i_mchb-atflv = c_23.
endif. " Condition for RATIO values
else. " If characteristic does contain RATIO
i_mchb-atflv = i_ausp-atflv.
endif.
i_output-atinn = cabn-atinn.
i_output-atnam = cabn-atnam.
i_output-atflv = i_ausp-atflv.
i_mchb1-matnr = i_mchb-matnr.
i_mchb1-werks = i_mchb-werks.
i_mchb1-lgort = i_mchb-lgort.
i_mchb1-charg = i_mchb-charg.
i_mchb1-clabs = i_mchb-clabs.
i_mchb1-atinn = i_ausp-atinn.
i_mchb1-atflo = i_mchb-atflv.
i_mchb1-atflv = i_ausp-atflv.
append : i_output, i_mchb1.
clear i_mchb1.
modify i_mchb index l_tabix transporting atflo atflv .
endif.
endloop.
endif.
endloop.
endif.
Checking whether the table is filled or not
if not i_output[] is initial.
sort i_output by atinn werks matnr atflv.
else.
g_exit = c_flag.
message s899 with 'No Data found for the Selection Criteria'(006).
endif.
Delete the records where RATIO is less than 13.
delete i_output where atnam cs c_ratio and atflv lt c_13.
endform. "append_final_data
*& Form display_report
Display the Report Output data
form display_report.
data: l_tabix like sy-tabix.
loop at i_output1.
l_tabix = sy-tabix.
At new Characteristic
at new atinn.
read table i_output1 index l_tabix.
format color 1 intensified on.
write: /1 sy-vline, 2(20) 'Characteristic Name:'(007),
23(40) i_output1-atnam,
125 sy-vline.
format color off.
format color 4 intensified on.
write: /1 sy-vline, 2(20) 'Plant Name :'(022),
23(4) i_output1-werks, 29(30) i_output1-name1,
125 sy-vline.
format color off.
write /1(125) sy-uline.
endat.
clear: g_clabs, g_clabs1.
format color col_normal.
write :/1 sy-vline, 2(18) i_output1-matnr,
20 sy-vline, 21(40) i_output1-maktx,
61 sy-vline.
if i_output1-atflv = c_c23.
write: 62(22) c_g23 centered.
else.
shift i_output1-atflv left deleting leading space.
write: 62(22) i_output1-atflv centered.
endif.
write: 84 sy-vline,
103 sy-vline,
110(5) i_output1-meins.
If the quantity value is negative
if i_output1-clabs ge 0.
write: 85(18) i_output1-clabs unit i_mchb-meins,
125 sy-vline.
else.
i_output1-clabs = - i_output1-clabs.
write i_output1-clabs unit i_mchb-meins to g_clabs1.
condense g_clabs1.
concatenate '(' g_clabs1 ')' into g_clabs separated by space.
write: 85(18) g_clabs right-justified,
125 sy-vline.
endif.
format color off.
hide : i_output1.
new-line.
At end of material
at end of matnr.
sum.
move : i_output1-matnr to g_matnr.
format color 3 intensified on.
write /1(125) sy-uline.
write :/1 sy-vline, 2(25) 'Total for Material :'(012),
28(18) g_matnr.
if i_output1-clabs ge 0.
write: 85(18) i_output1-clabs unit i_mchb-meins,
125 sy-vline.
else.
i_output1-clabs = - i_output1-clabs.
write i_output1-clabs unit i_mchb-meins to g_clabs1.
condense g_clabs1.
concatenate '(' g_clabs1 ')' into g_clabs separated by space.
write: 85(18) g_clabs right-justified,
125 sy-vline.
endif.
write: 125 sy-vline.
format color off.
write /1(125) sy-uline.
endat.
At end of plant
at end of werks.
sum.
move : i_output1-werks to g_werks.
format color 3 intensified off.
write :/1 sy-vline, 2(25) 'Total for Plant :'(013),
28(4) g_werks.
if i_output1-clabs ge 0.
write: 85(18) i_output1-clabs unit i_mchb-meins,
125 sy-vline.
else.
i_output1-clabs = - i_output1-clabs.
write i_output1-clabs unit i_mchb-meins to g_clabs1.
condense g_clabs1.
concatenate '(' g_clabs1 ')' into g_clabs separated by space.
write: 85(18) g_clabs right-justified,
125 sy-vline.
endif.
format color off.
write /1(125) sy-uline.
endat.
At end of characteristic
at end of atinn.
read table i_output1 index l_tabix.
sum.
format color 3 intensified on.
write :/1 sy-vline, 2(25) 'Total for Characteristic:'(014),
28(25) i_output1-atnam.
if i_output1-clabs ge 0.
write: 85(18) i_output1-clabs unit i_mchb-meins,
125 sy-vline.
else.
i_output1-clabs = - i_output1-clabs.
write i_output1-clabs unit i_mchb-meins to g_clabs1.
condense g_clabs1.
concatenate '(' g_clabs1 ')' into g_clabs separated by space.
write: 85(18) g_clabs right-justified,
125 sy-vline.
endif.
format color off.
write /1(125) sy-uline.
endat.
endloop.
endform. " display_report
*& Form DISPLAY_BATCH
Display the batch details for the seclected material *
form display_batch.
Get the batch details for the selected material
get cursor field g_cursor.
if g_cursor = c_cursor1 or
g_cursor = c_cursor2 or
g_cursor = c_cursor3 or
g_cursor = c_cursor4 or
g_cursor = c_cursor5 or
g_cursor = c_cursor6.
format color 3.
write: /1 sy-vline,
2(17) 'Material Number :'(020),
20(17) i_output1-matnr,
94 sy-vline.
format color off.
write /1(94) sy-uline.
loop at i_mchb1 where matnr = i_output1-matnr and
atinn = i_output1-atinn and
atflo = i_output1-atflv.
format color col_normal.
shift i_mchb1-charg left deleting leading '0'.
write :/1 sy-vline, 2(16) i_mchb1-lgort centered,
18 sy-vline, 19(17) i_mchb1-charg centered,
36 sy-vline.
if i_output1-atnam cs c_ratio.
write: 37(29) i_mchb1-atflv
exponent 0 decimals 2 centered.
else.
write : 37(29) i_mchb1-atflv
exponent 0 decimals 0 centered.
endif.
write : 66 sy-vline, 67(27) i_mchb1-clabs unit i_mchb-meins,
94 sy-vline.
format color off.
endloop.
write /1(94) sy-uline.
else.
message s899 with 'Invalid cursor position'(016).
exit.
endif.
endform. " DISPLAY_BATCH
*& Form HEADING_SECLIST
Write the Column Headings for Interactive Report
form heading_seclist.
write /1(94) sy-uline.
format color col_heading on.
write :/1 sy-vline, 2(16) 'Storage Location'(021),
18 sy-vline, 19(17) 'Batch Number'(017) centered,
36 sy-vline, 37(29) 'Characteristic Value'(018) centered,
66 sy-vline, 67(27) 'Quantity'(019) centered,
94 sy-vline.
write /1(94) sy-uline.
format color off.
endform. " HEADING_SECLIST
*& Form COLLECT_RATIO
Display the Characteristic ratio data
form collect_ratio.
loop at i_output.
clear g_atinn.
i_output1-atinn = i_output-atinn.
i_output1-atnam = i_output-atnam .
i_output1-werks = i_output-werks.
i_output1-name1 = i_output-name1.
i_output1-matnr = i_output-matnr.
i_output1-maktx = i_output-maktx.
i_output1-clabs = i_output-clabs.
i_output1-meins = i_output-meins.
call function 'CONVERSION_EXIT_ATINN_OUTPUT'
exporting
input = i_output-atinn
importing
output = g_atinn.
if g_atinn cs c_ratio.
If the ratio value is between 13-14.99, display 13
if i_output-atflv between c_13 and c_1499.
i_output1-atflv = c_13.
If the ratio value is between 15-16.99, display 15
elseif i_output-atflv between c_15 and c_1699.
i_output1-atflv = c_15.
If the ratio value is between 17-18.99, display 17
elseif i_output-atflv between c_17 and c_1899.
i_output1-atflv = c_17.
If the ratio value is between 19-20.99, display 19
elseif i_output-atflv between c_19 and c_2099.
i_output1-atflv = c_19.
If the ratio value is between 21-22.99, display 21
elseif i_output-atflv between c_21 and c_2299.
i_output1-atflv = c_21.
If the ratio value is greater than or equal to 23, display 23
elseif i_output-atflv >= c_23.
i_output1-atflv = c_23.
endif.
write i_output1-atflv to i_output1-atflv .
else.
write i_output-atflv to i_output1-atflv exponent 0 decimals 0.
endif.
collect i_output1.
clear i_output1.
endloop.
sort i_output1 by atinn werks matnr atflv.
endform. " COLLECT_RATIO
Reward if useful..
Regards,
Anji -
How to get the link between MCH1, AUSP, CAWN and CAWNT tables
Hi,
Can anyone let me know how to get the link between MCH1, AUSP, CAWN and CAWNT tables as I want to get the description (CAWNT-ATWTB) for a particular Batch (MCH1-CHARG).
Thanks & Regards,
KumarHi,
Can anyone let me know how to get the link between MCH1, AUSP, CAWN and CAWNT tables as I want to get the description (CAWNT-ATWTB) for a particular Batch (MCH1-CHARG).
Thanks & Regards,
Kumar -
How to get lines in between two fields in smartform
Dear Freinds,
I have developed one smart form however iam not getting output correct could you please help me out, the problem iam getting is iam not able to get the following things
in The Main Window
i have one header , one Main Area and one Footer Area
in the header i have created one %ROW1 and named as Row and again under the ROW i have
created a % Cell ...........again i want to create for the same Row iam not able to creeate another
Cell.........please let me know how i can have 5 or 6 cells for the same Row .
as i want the output as
UNit No. : 103 Quantity Req : 200 Date of Issue : 10/01/2008
Destination : Delhi Amount : 300 Rate/Per unit : 7
and secondly i have to have lines between the rows .... so please do let how to get lines in between rows as well..
i have tried allot but not able to get.
regds
madhuriHi Marcin Pciak ,
Thank you very much for giving me the solution, one more point i require in this regard
i have requirement as below
IDNo Invoice Amount
Despatch Date Despath Time.
Now i want i created Two Cell s (Cell A & Cell B) could you let me know how i can get IDNO and
Invoice Amount adjusacent to each other as above but right now iam getting in my smarform
IDNO
Invoice amount
but i want is IDNO-- Invoice Amount--
please help me this point
thanks once again for giving me answer.
regards
madhuri -
Was wondering if anyone can help me. We've lost signal on certain channels today.
The BBC channels as well as Pick TV, Dave, Really, E4+1, Movie Mix, Create & Craft, Sky News have no signal. Haven't checked EVERY other channel but they appear to be working fine.
Is this a known issue? Can anyone advise me as to how to solve the problem.
Cheers,
DaveCheck your local transmitter for any work
Plug aerial into TV and check if they are available on that
Check connections
If still missing unplug aerial and scan for channels. Plug aerial in and rescan.
Still not fixed by any of the above check your aerial, boosters etc
Life | 1967 Plus Radio | 1000 Classical Hits | Kafka's World
Someone Solved Your Question?
Please let other members know by clicking on ’Mark as Accepted Solution’
Helpful Post?
If a post has been helpful, say thanks by clicking the ratings star. -
Fieldpoint get info on 'all' channel
Hello
Can somebody, please, tell me how to get info which channels are in the 'all' channel?
I know how to do it in MAX and in project, but, how to get the info in *.vi?
For example, in my item xxx.xxx.xxx.xxx\FP\2AI\All are channels 2,4,7 and 8.
The output array from 'FP Read' has 4 values, corresponding to channel 2,4, and 8.
I need that together with the output array from 'FP Read', I get somehow info which channels are measured?
ThanksHello
Now, I am confused by your answer
In the project explorer, I can do the following (see attachments).
Depending on how many channels I choose, the size of the output array from 'FP Read' changes.
Please see the Item 'All', and the item 'bla'.
Also notice that, although they share common channels, they do not give the same values, because of the scaling.
So, I want to know, which channels are in the items (item can be named 'All', or any other name), and if possible get info on the scaling.
Thanks or any help
Attachments:
All_CH0,1,2.jpg 1003 KB
bla.jpg 1003 KB
get_values.jpg 968 KB -
PS5 - How do I get the hidden target channel to work with the typing tool?
PS5 - How do I get the hidden target channel to work with the typing tool?
I keep getting this error message everytime I try to move a box around.Have you tried an Adobe forum? PS5 is an Adobe product!
-
Query to get the difference between 2 totals from 2 different queries
I wanted to know if it is possible to get the difference between 2 totals from 2 different queries. I would explain with an example:
1st query - Select sum(homepass) from table 1
2nd query – select sum(homepass) from table2
Is it possible to display the difference like-
Select sum(homepass) from table 1 - sum(homepass) from table2
I know the above query would gives syntax error but is there a better way or a trick to get the above task accomplished from a single query.
I hope, my question is clear.
Please revert with the reply to my query.
Regardstomernitin wrote:
Try this one also:
WITH adtn1
AS
SELECT 110 val1 FROM dual UNION ALL
SELECT 100 FROM dual UNION ALL
SELECT 90 FROM dual UNION ALL
SELECT 10 FROM dual
adtn2
AS
SELECT 10 val2 FROM dual UNION ALL
SELECT 20 FROM dual UNION ALL
SELECT 30 FROM dual UNION ALL
SELECT 100 FROM dual
SELECT(Sum(a1.val1)-Sum(a2.val2)) Diff FROM adtn1 a1,adtn2 a2;
let me know if you still have any doubt.
Um.... I don't think so. Not with the cartesian join between a1 and 2. -
How to get the difference between two columns in a column group
Hi All,
My first time here and really new to programming. I would like to get the difference between 2 columns that are inside
a column group.
Here is my sample table below: The Column Group is PeriodNumber and can only choose 2. like 1 and 2.. I would like to have a third row which will simply calculate the difference between the amounts in PeriodNumber 1 and 2.
PeriodNumber
Account 1 2
1) Cash 10,000 15,000
2) Receivables 12,000 11,500
3) Equipment 5,000 5,500
Total Assets 27,000 32,000Hi yabgestopa,
From your description, you want to get the difference between two columns in a column group. After testing it in my environment, we can use custom code to achieve your requirement. For more details, you can refer to the following steps:
Copy the custom code below and paste it to your report. (Right-click report>Report Properties>Code)
Dim Shared Num1 As Integer
Dim shared Num2 As Integer
Public Function GetAmount(Amount as Integer, Type as String)
If Type = "1" Then
Num1=Amount
Else
Num2=Amount
End If
Return Amount
End Function
Public Function GetDif()
Return Num1-Num2
End function
Right-click the second column to insert a third column with Outside Group-Right.
Then use the expressions below in the matrix.
=Code.GetAmount(Fields!Amount.Value,Fields!PeriodNumber.Value)
=code.GetAmount(Sum(Fields!Amount.Value),Fields!PeriodNumber.Value)
=Code.GetDif()
The report looks like below.
If you have any questions, please feel free to ask.
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support -
Get Date Difference between 2 date values as days
Hi,
How to get the difference between 2 dates in number of days format. Say if i need the difference between 2012-08-23 and 2012-08-20 as 3
Please help..Hi,
You can do it in XSLT since the dates are in ISO 8601 format...
http://www.w3.org/TR/NOTE-datetime
Here is a sample XSLT...
<xsl:stylesheet version="2.0"
xmlns:xsl="http://www.w3.org/1999/XSL/Transform"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:fn="http://www.w3.org/2005/xpath-functions">
<xsl:template match="/">
<xsl:variable name="date1" select="xs:dateTime(/root/date1)"/>
<xsl:variable name="date2" select="xs:dateTime(/root/date2)"/>
<xsl:value-of select="fn:days-from-duration($date2 - $date1)"/>
</xsl:template>
</xsl:stylesheet>The above XSLT will result *4* for the following input...
<root>
<date1>2012-01-11T00:00:00.000-05:00</date1>
<date2>2012-01-15T00:00:00.000-05:00</date2>
</root>You can test this example here...
http://xslttest.appspot.com/
Hope this helps...
Cheers,
Vlad
It is considered good etiquette to reward answerers with points (as "helpful" - 5 pts - or "correct" - 10pts)
https://forums.oracle.com/forums/ann.jspa?annID=893
Maybe you are looking for
-
Inc0/1 and arch backup at the same time
Hi! During the inc0/1 backups I need to run additional archivelog backups. Otherwise the FRA is filled up. But then the the last part of the inc0/1 backup - the archivelog part - fails: Starting backup at 07//09/2010 current log archived released cha
-
How to use Javamail for accessing additional mailboxes -IMAP, Exchange 2010
hi, I want to access a shared mailbox (NOT FOLDER) via Javamail API (1.4.5) using IMAP(s) with plain logon. The mailserver is a Exchange Server 2010. User: user1 ([email protected]) pwd: xxxx shared mailbox: [email protected] Properties: mail.imaps
-
Need to create view ( Urgent )
Hi All, I have one requirement to create a view .Presently we are using a packaged procedure(view_test_123_pkg) to extract part numbers to write to a file using utl_file package. Now the requirement is to create a single column view to extract part n
-
Hi, I have set up a new account as I can't sign in. I requested a new password but it sent the request email for the new account. Therefore I can't get to my old account. The online help just keeps looping and not solving the problem. Therefore, How
-
Hello I'm new to spreadsheets and I've decided to make a smart shopping list. But I guess this formula doesn't look so smart. If I continue to add new Products to the list, the formula is going to get larger and larger. Just like any supermarket rece