I'm having trouble installing sound on the new install.

[krazybastid@localhost ~]$ ls -l /sys/module/snd/holders
total 0
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_hda_codec -> ../../snd_hda_codec
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_hda_codec_idt -> ../../snd_hda_codec_idt
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_hda_intel -> ../../snd_hda_intel
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_hwdep -> ../../snd_hwdep
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_mixer_oss -> ../../snd_mixer_oss
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_pcm -> ../../snd_pcm
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_pcm_oss -> ../../snd_pcm_oss
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_seq -> ../../snd_seq
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_seq_device -> ../../snd_seq_device
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_seq_oss -> ../../snd_seq_oss
lrwxrwxrwx 1 root root 0 Oct 24 20:50 snd_timer -> ../../snd_timer
and.....
[krazybastid@localhost ~]$ cat /proc/asound/modules
0 snd_hda_intel
1 snd_hda_intel
and... I went to type in the modprobe.conf
/etc/modprobe.d/modprobe.conf
# /etc/modprobe.d/modprobe.conf (for v2.6 kernels)
options snd_hda_intel index=0
I'm stuck I don't know what to do and I can't get sound to work I also did.. in ~/.asoundrc
defaults.ctl.card 0
defaults.pcm.card 0
defaults.pcm.device 0
Can somebody help?

It's ok I figured it out by typing alsaconf and it magically started working.

Similar Messages

  • Is anyone having trouble with internet on the new macbook air and an old modem?

    Is anyone having trouble with internet on the new macbook air using an old modem?
    I live in NYC and have an old modem/router and keep getting kicked off the internet. I have time warner as my internet provider.

    Hello there adell723,
    I suggest taking a look at this article we have named Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6 found here http://support.apple.com/kb/HT4628?viewlocale=en_US.
    Symptom: The network connection drops unexpectedly
    Your Mac may not not stay connected to your Wi-Fi network reliably.
    Your Mac may stop accessing the Internet during use.
    Solution
    Use these steps if your computer disconnects from its Wi-Fi network unexpectedly.
    Check your range to the Wi-Fi router and reduce the effect of interference.If your computer is too far from your Wi-Fi router or your environment has too much Wi-Fi interference, then your computer may not detect the Wi-Fi network properly. The easiest way to check for range limits with your Wi-Fi network is to move your computer or your Wi-Fi router closer together and make sure that there are no obstructions (such as walls, cabinets, and so forth) between the router and your computer.See Potential sources of wireless interference for more information about interference and solutions.
    Try connecting to a different Wi-Fi network. If your computer works fine when connected to a different Wi-Fi network, then the issue may be related to your network router or ISP. In that case, contact the manufacturer of your router or your ISP.
    If you have Mac OS X 10.8.4 Mountain Lion installed then I would recommend using Wireless Diagnostics tool which is on your computer already.
    Here is the article for it and how to use it to assist with wifi connectivity issues.
    About Wireless Diagnostics
    http://support.apple.com/kb/HT5606
    Cheers,
    Sterling

  • FIX: Having trouble opening extensions in the new CC 2014?

    Here's a link to the original post of this fix: Important: EB3 in Illustrator cc 2014
    Are you experiencing blank extension panels when opening them in Illustrator CC 2014? Well - here's the fix.
    In a nutshell (on a Mac):
    1. Navigate to /Users/<USERNAME>/Library/Preferences/com.adobe.CSXS.5.plist
    2. Open up said file in XCode.
    3. Under Root, add a string called 'PlayerDebugMode' and set it's value to 1.
    4. Restart your machine.
    5. Extensions should now work.
    Adobe, please post this fix on the top of the EB3 page and the top of these forums with flashing/blinking lights. I've been stoked to try out all the new Node capabilities and other goodies since the release last week, but haven't been able to do so until I found this today. I know I'm not the only one who's been banging their head against a wall trying to get extensions to work in CC 2014. I hope this saves you from sitting there thinking "What is wrong with my extension?!".

    Here's a blog post on the matter: Adobe Extension Builder and Creative Cloud 2014

  • HT201272 I recently upgraded from an Iphone 4S to 5. I am having trouble with magicjack; each time i install it it gives me an error message "The installation associated with this device is invalid". Cannot seem to access account info or make calls.

    I recently upgraded from an Iphone 4S to 5. I am having trouble with magicjack; each time i install it it gives me an error message "The installation associated with this device is invalid". Cannot seem to access account info or make calls.

    I have exactly the same trouble.
    If you wet the answer, please let me know!!

  • I am having trouble getting sound on video clips I have imported into Premiere Elements 10.

    I am having trouble getting sound when importing video clips into Premiere Elements 10.  Is someone able to offer me a solution as I have no idea what I have done to cause this to happen. 
    The clip has sound when opened with windows media player.
    Thank you

    Hi Steve,
    After reading everybody’s responses I am feeling a little out of my depth.  Being new to this I am having difficulty in understanding a lot of the information given to me and also in the information you require from me.  It appears that one thing I should never do is mix film from two different cameras.  I would really like to fix this one particular clip though as it holds an interview that was taken when leaving Coober Pedy and something that I don’t want to lose.
    I have today done some research on the camera that took the offending video clip.   It was a Samsung S85 and according to the Samsung website it uses MJPEG video format.
    Here are the specifications as per the Samsung website.
    Camera Type
    Ultra-Compact Point-and-shoot Digital Camera
    Image Quality
    Image Sensor
    1/2.5" 8.3 Megapixel CCD
    Effective Resolution
    8.2 million pixels
    Color Depth
    24-Bit RGB
    Color Modes
    Normal, B/W, Sepia, Negative, Red, Green, Blue, Custom Color
    Image File Formats
    JPEG (Super Fine, Fine, Normal)
    Recorded Resolution
    8M (3264 x 2448)
    7M (3264 x 2176) - 3:2
    6M (3264 x 1824) - Wide
    5M (2592 x 1944)
    3M (2048 x 1536)
    1M (1024 x 768)
    Video Recording
    AVI Motion JPEG with Audio
    640 x 480 @ 30 or 15 fps
    320 x 240 @ 30 or 15 fps
    Clip length limited only by available memory
    5x optical zoom available during video record
    Audio Recording
    WAV format (monaural)
    I downloaded and installed Media Info and Morgan Multimedia MJPEG Codec V3.99.108 today.  Do I have to register it to get it to operate?  I read the documentation file that came with it hoping to find a clue as what I should do but I could not comprehend the information it contained.
    Thank you and other members who have responded to my plea for all the help you have given me.
    Judy

  • I am having trouble with sound on my iPad

    I am having trouble with sound on my iPad

    Found the fix.
    If the reboot doesn't fix it.
    If the headphoens work find, but no external speakers.
    If the double-click and page right to the software mute, doesn't show the sound knob - just the brightness
    If your pop-up shows "Docking Station"
    Then, the problem is very likely a dirty connector.  The iPad/iPhone/iPod connector uses a resistor value to determine if the device is connected to an external 'speaker'.  There are a range of resistances, for a range of products.  This is known as the Connector Pin 21 issue.
    Take some windex on a que-tip, or perhaps a Windex paper scrub and rub it on the bottom connector port.  Somehow, "something" has gotten on those contacts, and it is pulling the voltage on pin #21 down - so that the iPad "thinks" it's connected to an external speaker - this will disable the internal speaker circuitry, as well as the internal speaker volume controls.
    Do not over-saturate and short out your iPad.  Do not throw it in the sink, do not use the kitchen faucet to flush it out.  A Que-tip with a few drops of Windex (or other gentle cleaner) should work just fine.  Takes all of 30 seconds - and magically, the volume knob appeared and everything worked just fine.

  • I am having trouble opening Adobe Reader after I install it in my Safari.

    I am having trouble opening Adobe Reader after I install it in my Safari. I have installed reader about 10 times now and it says I can use it now, but when I try to open a file it tells me I need to launch Reader and Agree to terms. I really need to use it now for school. Please help. Thank you, Heather

    You need to open Reader outside of Safari Start>All programs and accept the agreement.

  • I'm having trouble staying connected to the internet

    I'm having trouble "staying" connected to the internet.

    hmmmmmmm..........
    How are you connected to "the internet?"  There are many ways & you provided none.
    If wireless, are you using one of Apple's routers, or a 3rd part one?  If the latter post in their forums or contact their tech support department.
    Last but not least: 
    Please detail all you have done to resolve your issue.  Need this information so that the users can avoid the "been there, done that" scenario type responses.  This is to avoid repeating the troubleshooting you may have already tried.  Thank you.

  • I am having trouble with Itunes registering the Mp4 video that has been converted.  Help!!

    I am having trouble with Itunes registering the MP4 video that has been converted.  Help!

    What do you mean by iTunes registering the mp4?
    Which iTunes, on iPad, iTunes is a Store and it won't take your .mp4.
    On pc, check if it supports the mp4 (there are a number of different mp4 format) you have converted.
    Can you import it to computer iTunes?

  • Having trouble with sound on my iphone 3gs ringtones work but ipod doesnt any ideas?

    having trouble with sound on my iphone 3gs ringtones work but ipod doesnt any ideas? have tried resetting cleaning earphone dock and still not working

    Same here, I get no sound from videos, text messages. This happens for a while, then it works again then it doesn't work. When I go to settings, my "change with buttons" is on but buttons don't work. I have restored it but there is no change. Here is a picture of my screen when i try to change volume.

  • I'm having trouble importing pictures from the internet....when I drag the picture to the icon, it gives me the option to import all duplicates. Even when I click "NO", it STILL imports every picture I have imported AGAIN, including the new one! WHY??

    I'm having trouble importing pictures from the internet....when I drag the picture to the icon, it gives me the option to import all duplicates. Even when I click "NO", it STILL imports every picture I have imported AGAIN, including the new one! WHY??

    carolinechx wrote:
    i know the description may be a little bit too confusing
    Mostly because you are not using any capital letters or paragraph returns and your post is difficult to read.

  • I am having trouble getting mail from the server that my new iMac is connected to. I have to reboot the system to get Outlook for Mac to access the system. Any ideas?

    I am having trouble getting mail from the shaw server that my new iMac is connected to. I have to reboot the system to get Outlook for Mac to access the system and obtain new messages. Any ideas? Its at the point where I have started using the PC again as its less trouble.......

    In Firefox 3.6.4 and later the default connection settings have been changed to "Use the system proxy settings".<br />
    See "Firefox connection settings" in [[Server not found]]
    You can find the connection settings in "Tools > Options > Advanced : Network : Connection"<br />
    If you do not need to use a proxy to connect to internet then select No Proxy

  • Hi I am having trouble with iMessage on the mac book pro, it doesnt sync with the ipad and iPhone, both the ipad and iPhone do but not on the mac book pro , has anyone any suggestions, thanks in advance

    Hi I am having trouble with iMessage on the mac book pro, it doesnt sync with the ipad and iPhone, both the ipad and iPhone do but not on the mac book pro , has anyone any suggestions, thanks in advance

    First, make sure that all your devices are using the same Apple ID in iMessages including your Mac.  Second, your messages that you've already started on your devices will not show up on your Mac - only ones that you start from now on will show up.  Third, if you're still not syncing accross all devices, make sure you read the directions on the first page of this thread.  It should work after performing those steps.  Good luck!

  • Can't login to Windows Azure account 'We are having trouble logging you into the portal'

    Hi,
    I have been unable to login to Windows Azure account or Azure support sites for about a month now. I activated my account using company MSDN subscription.
    I get the same error message in both cases:
    We are having trouble logging you into the portal.
    See screenshots bellow:

    Hi Mark,
    May I know whether you have followed below steps to contact with Azure customer support?
    Get the support channel at:
    http://www.windowsazure.com/en-us/support/options/
    Select a support topic ==>>I cann't sign in to Microsoft Azure
    Log the information as required and submit the ticket.
    A Microsoft support professional will contact with you as soon as we can
    Sincerely apologize for this inconvenience and we appreciate your patience.
    Should you have any other concern, please feel free to let me know.
    Thanks.
    Best Regards,
    Will
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • Having trouble threading frames, getting the wrong loaded cursor, not the chain-links

    Hi there, I am trying to thread frames, which hasn't been an issue for me previously. The cursor usually shows the chain link icon when hovering over the second frame, but today it is showing a square icon and when I try to click into the the second frame instead, it tries to create a new text frame. Any help is appreciated. Thanks!

    i had put the two text boxes on different layers before to show that they were separate frames, they actually live on one layer together.
    Re: Having trouble threading frames, getting the wrong loaded cursor, not the chain-links 

Maybe you are looking for