I'm seeing a high runt count on my serial interfaces after upgrading to 12.

I'm seeing a high runt count on my serial interfaces after upgrading to 12.2(37).
I was looking for information on what changed in 12.2(37)and some more detailed information on runts.
I know that runts are smaller than the medium's minimum packet size. But I want more specific information and I can not find meaningfull information.
Any Ideas

On a serial interface I would contribute the runts to a timing problem which is not an easy problem to isolate esp. with a telco. Even though there may be no CRC or Frame errors.

Similar Messages

High Runt Count on 6513 for Particular PC

Hi, We are currently seeing a High runt count from our 6513 Switch when we have a Desktop PC configured with a Realtek 8139 NIC installed with the lastest drivers for XP. There are no negotiation issues as both ends are setup correctly at 100/FULL. Also if we plug this device into one of our edge 3524 switches we get no errors/runts. I believe there maybe a configuration issue on our 6513. If someone could provide some info or if you require more information that would be great.
Thanks Simon

I suggest to try to enable auto-negoitation for speed and duplex to test it again. Otherwise, it may be a compatiblity issue.
It may be a silly suggestion, but please also try to replace the UTP cable and test again.

I have Lion, and I can't see my unread messages count in the dock, even after the preferences set up. I find the Lion Mail too complicated. Leopard was much easier and more simple to use. I only have one account& don't need all the rest. any suggestions

I have Lion, and I can't see my unread messages count in the dock, even after the preferences set up.
I find the Lion Mail too complicated. Leopard was much easier and more simple to use. I only have one account& don't need all the rest.
any suggestions?

weird.
It's so frustrating, I got my Mac Book 5 days ago and I'm already having a discussion in the forum.
Thank you so much for your prompt replies.
It's past midnight here so I'd better get some rest...
Good night captfred!

Is there a resource where I can see if my older versions of applications will work after upgrading to 10.8 from 10.6.8? I have some older Mac apps as well as things like Microsoft word and Adobe professional.

Is there a resource where I can see if my older versions of applications will work after upgrading to 10.8 from 10.6.8? I have some older Mac apps as well as things like Microsoft word and Adobe professional. I know PowerPC apps won't work, but I can't tell by the version numbers if they are PPC or Intel.

Dr Jack wrote:
I know PowerPC apps won't work...
Restore the ability of PowerPC apps to work: Install Snow Leopard (with Rosetta) into Parallels:
[click on images to enlarge]
Full Snow Leopard installation instructions here:
http://forums.macrumors.com/showthread.php?t=1365439

Photoshop CC can't seem to handle complex/high poly count 3D Models. Will this be addressed?

Hello all,
I am running Photoshop CC on 3 systems and having the relatively same problems on all. The source files are exported from ZBrush- .stl or .obj files that are complex and have high poly counts. The file sizes are into the hundreds of megabytes. These are not the simple files like they show when people are using the 3D features- a racecar or simple toy rocket.
Photoshop CC doesn't seem to be able to open all the files and even when it does, the structures facings or facets don't always appear correct. I've developed a partial workaround, by merging the objects and reducing the poly count (which creates a new set of problems).
If I do get a file open, my ultimate goal is to be able to color it, add light it and render it for 2d print purposes. Again Photoshop seems to be picky- When I apply color via the airbrush tool, it usually isn't smooth. It seems to apply color by facet or facing. Same thing when I try to manually add in texture from another source file. It appears to make the detail jagged and blurry from the source file.
The appeal of using Photoshop for this process is we have people here who can do it without too much of a learning curve. Otherwise everyone else has to learn ZBrush just to color and light the models.
I've pretty much done all the troubleshooting I can and exhausted all the tools at hand. I have tried both texture painting and projections painting and all the other options. I believe the meshes are just too complicated. And if there is something incorrect in the file, such as a reversed normal, Photoshop doesn't seem to know how to deal with it. My systems have more than enough to handle the files.
Does anyone have any similar issues and is Adobe working on them in the form of a new release?
Thanks!

Hi Everyone. Thank you for writing back. I have two 2011 imacs running intel 2.93 ghz, one with 20gb or ram and one with 16gb, both have 1tb hard drives, 1gb vram, one running os 10.6 the other 10.9. I have a 3rd computer, a PC that notably handles the files more quickly, but still crashes if it doesn't like something from the original 3d model. This one has a 3.7ghz intel quadcore processor, 24gb of ram, 3tb hard drive, and a 4gb nvidia geforce video card, running Windows 8.1.
So the reason I make the statement about Photoshop and not about my computers, is that all the above computers can handle the original files in zbrush. All the above computers can handle the files in meshlab. With ease. But when I get to photoshop, I face long load times, crashing, and a lag using the tools within the 3d space. And sometimes it handles the models differently than it does in any other 3d program. It seems picky for lack of a better word.
When I say high poly count, I mean 4 million to 8 million. I am able to knock down the poly count in meshlab and that can help. But sometimes the files just don't want to open in Photoshop.
With all that said, it may be in something how some of the models were built, but again, Photoshop is the only one having an issue. And I have to add that I have been using Photoshop for 20 years and I absolutely love it. I am trying to make a case for my company to use it for coloring, lighting, and processing 3d models, but I just can't with the above issues.
Any help would be greatly appreciated.
Chris, if you need files, I can see about getting them to you. The only real issue is the work is highly proprietary and kept under wraps. So I would need to get approval and feel comfortable that is will be protected. Thanks!

High error counts

Will high retry counts and the inherent dropped packets between two bridged BR1310G radios cause packet errors on their respective ethernet switchports?
Dave

Hi Dave,
If you have retries and dropped packets between the Radio link , it would effect the TCP retransmission , however can you please clarify where you are seeing packet errors are you seeing or referin to " show interface fa/gi 0/1 etc" on br1310 bridge.
-Sri

High thread count on store.exe

I understand that the mdb store process utilizes as much memory as is available. My question is regarding the thread count on the process. One of the three mailbox servers tends to have a higher thread count than the other two. It
usually ranges from 150 to 200 (while the other two are usually 130 to 150) but today it is a little over 300. The rpc thread count on all the mailbox servers stays pretty low (60 or under) and the rpc thread count on the CAS servers usually
hang out around 55-65, so that's all good. All three mailbox servers also use VERY close to the same amount of memory all the time, so that doesn't seem to be making a difference. I am just trying to determine why the thread count is noticably
higher. This server and one of other mailbox servers replicate the public folder database, and I can understand why that would account for some additional activity, but you would think the thread count would be higher on the other server with the public
folder database as well, but it stays pretty low. Hardware-wise these servers are all identical. So is there something I can monitor in perf mon for instance? I don't want to use experfwiz because that monitors everything under the sun and
I need it a bit more centralized. I have googled all over the place and the only thing I can find is that with newer versions of exchange this thread count ranges from 200-300 on heavy usage, and exch07 can handle up to 500 threads, so I can't even find
which specific things to monitor that directly correlate with this issue. So while I understand that it's not really too high, I would like to find out why it deviates from the norm if the other two servers are equal for all intents and purposes (same
hardware, balanced DAG. etc). I would like to mitigate any potential issues. Thank you.

Hi pchw,
Thank you for your question.
I am sorry that we could not find the specific things to monitor this issuer directly, because there are many reason which caused it. For example: virus, big size attachment in queue, hardware performance and so on. We could refer to the following steps
to troubleshoot:
Restart the service of “Microsoft Exchange transport”;
Create a new database and move mailbox to new mailbox;
We could do some disk health check if the load test is normal;
Collect related application log and system log to
[email protected] for our troubleshooting.
We could run SDP on Exchange server and send it to
[email protected] for our troubleshooting.
http://blogs.msdn.com/b/askie/archive/2012/05/22/introduction-to-support-diagnostics-platform-sdp.aspx
We could use tools and logs to analysis if there are anything wrong or abnormal on Exchange server 2013. our bottle neck is disk IO latency, store.exe do require some CPU usage, but if our disk IO speed can keep in a normal range, the
CPU usage will be smaller. Exchange is highly rely on disk IO performance because it need lots of IO operation regarding to transaction log and database file. If Disk IO has a high latency, I will definitely impact store.exe, if it`s getting seriously sometimes
it may cause store.exe no response.
We could refer to the following link:
https://technet.microsoft.com/en-us/library/ee832791(v=exchg.141).aspx
If there are any questions regarding this issue, please be free to let me know.
Best Regard,
Jim

Why does my 10GB iSCSI setup seem see such high latency and how can I fix it?

I have a iscsi server setup with the following configuration
Dell R510
Perc H700 Raid controller
Windows Server 2012 R2
Intel Ethernet X520 10Gb
12 near line SAS drives
I have tried both Starwind and the built in Server 2012 iscsi software but see similar results. I am currently running the latest version of starwinds free
iscsi server.
I have connected it to a HP 8212 10Gb port which is also connected via 10Gb to our vmware servers. I have a dedicated vlan just for iscsi and have enabled
jumbo frames on the vlan.
I frequently see very high latency on my iscsi storage. So much so that it can timeout or hang vmware. I am not sure why. I can run IOmeter and
get some pretty decent results.
I am trying to determine why I see such high latency 100'ms. It doesn't seem to always happen, but several times throughout the day, vmware is complaining
about the latency of the datastore. I have a 10Gb iscsi connection between the servers. I wouldn't expect the disks to be able to max that out. The highest I could see when running IO meter was around 5Gb. I also don't see much load
at all on the iscsi server when I see the high latency. It seems network related, but I am not sure what settings I could check. The 10Gb connect should be plenty as I said and it is no where near maxing that out.
Any thoughts about any configuration changes I could make to my vmware enviroment, network card settings or any ideas on where I can troubleshoot this. I
am not able to find what is causing it. I reference this document and for changes to my iscsi settings
http://en.community.dell.com/techcenter/extras/m/white_papers/20403565.aspx
Thank you for your time.

I have a iscsi server setup with the following configuration
Dell R510
Perc H700 Raid controller
Windows Server 2012 R2
Intel Ethernet X520 10Gb
12 near line SAS drives
I have tried both Starwind and the built in Server 2012 iscsi software but see similar results. I am currently running the latest version of starwinds free
iscsi server.
I have connected it to a HP 8212 10Gb port which is also connected via 10Gb to our vmware servers. I have a dedicated vlan just for iscsi and have enabled
jumbo frames on the vlan.
I frequently see very high latency on my iscsi storage. So much so that it can timeout or hang vmware. I am not sure why. I can run IOmeter and
get some pretty decent results.
I am trying to determine why I see such high latency 100'ms. It doesn't seem to always happen, but several times throughout the day, vmware is complaining
about the latency of the datastore. I have a 10Gb iscsi connection between the servers. I wouldn't expect the disks to be able to max that out. The highest I could see when running IO meter was around 5Gb. I also don't see much load
at all on the iscsi server when I see the high latency. It seems network related, but I am not sure what settings I could check. The 10Gb connect should be plenty as I said and it is no where near maxing that out.
Any thoughts about any configuration changes I could make to my vmware enviroment, network card settings or any ideas on where I can troubleshoot this. I
am not able to find what is causing it. I reference this document and for changes to my iscsi settings
http://en.community.dell.com/techcenter/extras/m/white_papers/20403565.aspx
Thank you for your time.
If both StarWind and MSFT target show the same numbers I can guess it's network configuration issue. Anything higher then 30 ms is a nightmare :( Did you properly tune your network stacks? What numbers (x-put and latency) you get for raw TCP numbers (NTtcp
and Iperf are handy to show)?
StarWind VSAN [Virtual SAN] clusters Hyper-V without SAS, Fibre Channel, SMB 3.0 or iSCSI, uses Ethernet to mirror internally mounted SATA disks between hosts.

Using aperture 3.2. How do I convert my photos back to high mg count so I can upload to a site for printing LARGE?

Help. Is it possible to convert my manipulated images (which were originally shot in RAW format) and manipulated with "plug ins/COLOR EFEX PRO" in my APERTURE 3.2 program on mac... back to a high mg count? It seems they got diluted with each layer I added. When I uploaded them to a website for BIG CANVAS printing they arrived at that site watered down to 2.-4. mgs. When they started at 18 to 20mgs.
Please I need help. Thanks.

You are welcome.
The other... I did realize that if I export and resize the photo in MOST cases I can get almost recapture the exact clarity.
Can you give an example of the cases that still look "diluted"? What image format do you use to send the images to the plug-in (in the Aperture Preferences -> Export: psd or tiff, 8bit or 16 bit), and which export do you use when exporting from Aperture?
export and resize the photo
What do you mean? At which stage of your workflow do you resize, and how exactly?
Regards
Léonie

When I synch, a lot of songs have higher play counts than actual play. What to do to ensure integrity of play counts?

When I synch my iPhone to my MAC, a lot of songs have higher play counts than actual. What can I do to ensure integrity of play counts?

If you're talking about "regular" icloud, then setting it up should have no effect on your music. Try syncing the device to iTunes and check the music settings and sync again.
If you subscribe to iTunes Match, is the device in wifi range?

Unread email count Is 3900 after upgrade to IOS 8.1.2

AFter upgrading to IOS 8.1.2 my unread email count jumped to 3900 even though there is no email on my phone and none on the server. Is there a way of clearing this count?

Hi, jaff067.
Thank you for visiting Apple Support Communities.
I understand that you have an unread message counter, but your mail account indicates all mail is read. This usually means that you have an additional mail account setup. Check to see if you can access this account or change mailboxes and clear the unread via the steps below.
Write messages
Cheers,
Jason H.

Unable to see JSF pages in Design View after upgrade to Netbean 6.1

Hi:
I have a Sun Java Studio Creator Update 2 Project and I upgraded to Netbean 6.1 according to Sun's migration guide. It compiles and runs OK, but i can not see any page in design view at all.
Any one has any idea?
thanks

Hi Sriram,
I want to see commit stats on SM50 while background job runs. I unable to see on after upgrade.
all db stats are updated. On Sm50 screen unable to see Database commit count.
Cheers,
Harish

CS5.5 - High CPU usage in Premiere - New Video Card upgrade?

I'm running CS5.5 and I'm getting choppy video while editing in Premiere and did some research on how to fix that like render frequently, set Premiere as 1st priority, kill everything else thats running. I've done these and it's helped a bit but it still gets choppy.
The computer that I'm running was given a gift and is all I have to deal with currently so w/ that said its a Gateway SX2801-11e which has Vista 7 64 bit, Intel dual core E5700, 3GHz, 640GB hard drive, 6GB memory DDR3. So I was wondering if upgrading the video card would help out. But there may be a problem and may be limited... There is a PCI-Express graphics card slot but the case can only fit a half-height card and also against me is the low wattage. Any ideas on what I can do, recomendations? If it makes any difference, monitor I'm using is a 47" LCD television, 1080p.

I agree with Harm:
At this point you should save up for an entire new rig. As you can see from the PPBM5 results list, a system based on a Core 2 Quad CPU (unless overclocked heavily and/or equipped with a ton of RAM) cannot beat a system based on a Sandy Bridge dual-core i3-2100 CPU. Core 2 Duo CPUs are even slower than the Core 2 Quad example. And the Pentium E5700? Fuggedaboutit.
And even if you could upgrade the CPU and add a discrete GPU and additional disks, the Gateway is still saddled with a very limited motherboard that does not support RAID and lacks any overclocking provisions at all whatsoever.
In the end, you just have a system that (even after upgrading the RAM to its 8GB maximum and the fastest Nvidia CUDA GPU and adding two additional fast hard drives) is still much, much slower overall than even an i3-2100 system with only 4GB of RAM, let alone a fast i7 system with 16GB or more RAM. Thus, any upgrades that you make to that PC is an almost complete waste of money. (And as I discovered, every single one of the Core 2 Duo systems on the PPBM5 results list took more than 1,000 seconds to complete all of the PPBM5 benckmark tests with MPE turned on.) And even the higher 3GHz clock speed of the E5700 is not high enough to compensate for the deficiencies of the Pentium Dual-Core CPU (less L2 cache than the Core 2 Duo that the Pentium Dual-Core is based on), so that the E5700 is just as slow as, if not slower than, the E6700 systems near the bottom (lowest-ranked, or highest rank number) of the PPBM5 results list.

10.6: Apple and our customers place a high value on simple, refined, creative, well thought through interfaces. They take more work but are worth it. Apple sets a high bar. If your user interface is complex or less than very good it may be rejected

i am newbie in IOS i am web developer
so i use html 5 and i development jquery mobile based application.
in my application i just call view from web.I used objective c webview .
but my application rejected following issues
- Included low resolution/jagged image/s; see screenshot
- Portions of your app loaded, refreshed, ran, and/or responded very slowly.
- Was not optimized to support the device screen size and/or resolution; see screenshot
- Did not integrate with iOS features.
they said your app is slow but app speed is good(you can see here : http://teknonova.com/Map)
they said did not integrate with ios features .yes i just call URL from web view?is it illegal?
and they gave issues screenshot there is no problem with screenshot .it is good : (http://a1523.phobos.apple.com/us/r30/Purple/v4/c3/76/8a/c3768ae0-9b41-820f-9315- 40db2afc57b6/temp..gwvpnmiu.png)
what should i do?
should i delete and add new app?

10.6: Apple and our customers place a high value on simple, refined, creative, well thought through interfaces. They take more work but are worth it. Apple sets a high bar. If your user interface is complex or less than very good it may be rejected
for this problem what is a good solutions, how need to solve our problem, we need to published our apps. so plez telme the solution for this resons

High CPU load and com.apple.ImageCaptureExtension2 crash after upgrade

After upgrading my Macbook Air from Lion to Mountain Lion, the system has a very high cpu load, and the crash reporter is the process that causes thee high load. In the error log I see this entry several times per second:
17.08.12 12:58:46,011 ReportCrash[5998]: com.apple.message.domain: com.apple.crashreporter.writereport.crash
com.apple.message.signature: Image Capture Extension
com.apple.message.signature2: com.apple.ImageCaptureExtension2 ||| 8.0 (8.0)
com.apple.message.signature3: 03A96CBDA3C85A114383537BFC5C8999
com.apple.message.result: NO
com.apple.message.summarize: YES
I investigated a bit more and recovered, that it has something to do with the printer drivers. When I remove all printers from setting, everything is fine. As soon as I add a printer (Brother MFC 9440CN printer/scanner, printer driver provided by Mountan Lion), the crash reporter starts it's work and the error log is full of those entries.
Any suggestions?
Thanks in advance,
Marcus

I did more exploration and found the cause of this, but I don't know how to fix it:
I removed all Brother and Lexmark printer drivers and rebooted (and also tested with a virtual machine using 10.8.0 as guest os that never had any printer installed). As soon as I enter the printer settings and press the "+", the crashes begin, so it looked like the bonjour one of the printers announcing themselves via Bonjour were causing this.
When watching a picture in the preview app the same happend. We have two multi function printers in our network, the already mentioned brother printer and a Lexmark X204N. Switching off the Lexmark (which wasn't installed on my Mac) solved the problem. Switching off the printer is no solution in our office (it's our fax device and main printer), but switching off mDNS on the Lexmark also solved it. But this can only be a workaround.
Is this a known problem with Lexmark devices and Mountain Lion (it works fine with machines using Lion)? Are there any fixes known? It's just the Lexmark device announing itself via Bonjour that causes trouble, even if the driver is not installed.

I'm seeing a high runt count on my serial interfaces after upgrading to 12.

Similar Messages

Maybe you are looking for