I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

Let me see if I can help you with the basic WDS configuration steps:
Note: To help facilitate the setup, temporarily connect the AXn directly to the AEBS LAN port using an Ethernet cable. Once the setup is complete, you can move the AXn to the desired location. For all configuration steps you will be using the AirPort Utility. Before starting, be sure to jot down the AppleIDs for both base stations.
802.11g AirPort Extreme Base Station (AEBS) Configuration
AirPort Utility > Select the AEBS > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network
Manual Setup > WDS tab
WDS Mode: WDS main
Allow wireless clients (checked)
WDS Remotes: <enter the AppleID for the AXn here>
Click on Update and allow the base station to restart.
802.11n AirPort Express Base Station (AXn) Configuration
AirPort Utility > Select the AXn > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network (Note: You may have to hold down the Option (Mac) or Control (PC) key to see this option in the list.)
Manual Setup > WDS tab
WDS Mode: WDS remote
Allow wireless clients (checked)
WDS Main: <enter the AppleID for the AEBS here>
Click on Update and allow the base station to restart.

Similar Messages

Comcast just replaced my cable modem/wireless router. All devices connect properly except my iPhone 4. It shows itself to be connected to the network, but it does not load any web page. Resetting the iPhone does not solve the problem. Any suggestions?

Comcast just replaced my cable modem/wireless router. All devices connect properly except my iPhone 4. It shows itself to be connected to the network, but it does not load any web page. Resetting the iPhone does not solve the problem. Any suggestions?

Thank you for your response.
I had rebooted the router (several times, actually), to no avail.
I do not know the answer to whether MAC filtering is enabled on the router. Have tried to find info about that, but unsuccessfully. Router is an Arris TG852G, supplied by Comcast. I would be surprised if MAC filtering were the issue, since in addition to the computer, we have successfully connected several other devices to the wifi, namely an iPad, a Android phone and a Kindle Fire - all able to access internet pages through the wifi, and all without a need to add the device to a MAC address whitelist. To add to the mystery, the Comcast tech was able to connect his iPhone 4 to my network and access web pages. He was unable to connect my iPhone, however, after trying for some time.
I seem to recall reading somewhere that an iPhone cannot connect to a wireless "n" router, only "b" or "g". The Arris router is described as a n/g/b compliant router, and as noted the Comcast tech was able to connect his iPhone, so don't know why that would be the issue here.
By the way, my iPhone does connect wirelessly to my network at home. This difficulty is at a second home.
Any other thoughts would be appreciated.

My program does not work properly. I run the program but it is not capable of adding any of my ebooks and when I connect my ereader, it recognises the device but it does not add any ebook either. I uninstalled the program and reinstalled again but nothi

my program does not work properly. I run the program but it is not capable of adding any of my ebooks and when I connect my ereader, it recognises the device but it does not add any ebook either.
I uninstalled the program and reinstalled again but nothing gone better-
What should I do?
Best regards

Do you have Logitech gaming software installed on the PC? If so, perhaps try the suggestion from the following post:
Re: Everytime I close Itunes it loads back up

How can one use one specific security realm per application ? The realm-name attribute of the login-config tag of web.xml does not make any difference

Hi,
I have different sets of users coming from different databases and using different
roles mapping for each of my web applications. I would like to configure a specific
security realm per application in my weblogic server 7.0 . Is it possible ?
I try to specify the realm-name of the login-config tag from the web-xml deployement
descriptor but it doesn't make any difference. The default realm is always used.
I also would like to tell the Weblogic server to use the default realm in case
the realm isn't specified or isn't found. For example, the default would contains
my admin users.
Thanks a lot for your answer.
Iz

I thik this is a common mistake the ralm-name tag in the deployment descriptor is used
just by the browser for display purposes (when it opens the basic auth dialog box) so as
of now there is only 1 active realm which can have multiple providers as Kevin pointed
out
Kevin Lewis wrote:
WebLogic 7 now ignores the realm-name tag (I found that out yesterday).
My understanding is that there is only one realm active at a time for a domain
(I would be interested in being contradicted in this).
However, you can have multiple providers in each category of a realm: authentication,
authorization, etc. Therefore, what you can do is key authentication, et al,
off of some other information. We have our users enter their company, for example,
and use the TextInputCallback to get it. You could also encode something in the
initial page, based on the URL they hit, or whatever, and get that back in your
callback.
You can store that information in your own Principal implementation, and key off
of that in your authorization provider, going to a different database as appropriate,
or abstaining when a specific provider doesn’t have anything to say about a subject.
Anyway, there should be a way to do it, even if it's more complex than you would
have hoped.
--Kevin

Font size is too small in flash applications and the "zoom" feature does not make any difference. Thanks

Zoom dosen't work in flash applications and it is crazy small and too hard to read...this does beat out the fact you can't right click using flash in google chrome...I prefer firefox, but will go back to IE if it is the only program without such major bugs
I have also reset the minimum text size in flash and that did not help the problem at all.

Zoom dosen't work in flash applications and it is crazy small and too hard to read...this does beat out the fact you can't right click using flash in google chrome...I prefer firefox, but will go back to IE if it is the only program without such major bugs
I have also reset the minimum text size in flash and that did not help the problem at all.

I reinstalled my mac os x, and anytime i try to update my software its asking me for an administrators name and password, i enter it and it comes back wrong, and that is the only one i have, i have been to keychain but it does not make any sense to me,

i have just reinstalled my mac os x, in fact yesterday, i have not been able to update my software or change anything at all, i try to do a software update and it is asking me for an administrators username and password that was not happening before, i enter the username and password i created and it comes back wrong, its driving me nuts, been to keychain but unable to figure it out, its asking for a system unlock and i have no clue what that is.
am desperate.

Stick the 10.6 disk into the computer and reboot holding the c or option key down, select the disk to boot from.
In the installer menu is a Utiltiies menu and a password reset.
If you don't remmember the name, reboot the computer holding the command and s keys down
a black screen with white type appears, when it's finished, dbackspace any extra ssss you have made and then type
ls /Users
(that's Larry, Sam, space, slash, Users)
and press return, a list of user names on the machine appears
type exit and reboot and use the 10.6 disk to reset your password

TS1559 this does not make any difference

Wifi is STILL greyed out.

restart the phone
http://ipod.about.com/od/iphonetroubleshooting/qt/reset_iphone.htm
if that don't fix it
http://support.apple.com/kb/ht1414
if that don't fix it turn it in for repair

Hello, the 'Save As' dialog box used to allow the backspace button to go up one level in the directory when the focus is in the folder contents box but it does not work any more, please help.

Hello, the 'Save As' dialog box used to allow the backspace button to go up one level in the directory when the focus is in the folder contents box but it does not work any more, please help. BTW the same 'Save As' dialog in other applications still allow the backspace button to go up one level in the directory.

cor-el,
I kept forgetting and procrastinating about following your instructions, since I have internet access only for limited amounts of time and usually I am busy with important tasks when I am.
Out of the blue, the problem corrected itself (the Save As box started to open full screen, then shrunk down to a normal size and the edges can now be dragged to a custom size).
Even the copy and paste problem in the filenaming area seems to have been less troublesome lately even though there have been no updates to Firefox in a few weeks.
Even though I marked the solution as not helpful, the problem has in fact been resolved. I will save the solution instructions in case the issue returns.

IPhone equalizer does not make a difference

I set EQ presets to all my songs in iTunes. When I change the EQ settings on my iPhone (3.1) while listening to a song, it does not make any difference to the sound, regardless of the preset I choose.
Any clues or suggestions? What is the difference between off and flat?
Yvan

is your mute switch turned on (above the volume) ? remove case and screen protecter.
is volume turned up?
if so do this
account security
Please call apple @ 1-800-692-7753 in USA
ask for the account security team
you may want to add a credit card to your iTunes account before calling; so they will have a way to verify your identity.
Peace, Clyde
check # for your country
http://support.apple.com/kb/HE57
<Edited by Host>

My iPad 1 does not make any of the sounds (key clicking, etc) I have directed it to despite having volume turned all the way up...any thoughts?

my iPad 1 does not make any of the sounds (key clicking, etc) I have directed it to despite having volume turned all the way up...any thoughts?

Check to see if the "silent" switch is turned on. This is either the hardware switch next to the volume control or a software switch on the "recent apps" tray depending on how you have your iPad configured (Settings > General).
Too see the software switch on the "recent apps" tray double-click the Home button and swipe the tray to the right.

My iphone 4 does not make any sound except when i have call. Any sound notification for example whatsapp or email or playing song i could not hear a pip, but when blug the earphone i could hear all sound via earphone, any advise??

My iphone 4 does not make any sound except when i have call. Any sound notification for example whatsapp or email or playing song i could not hear a pip, but when blug the earphone i could hear all sound via earphone, any advise??

Check the Mute switch, which is on the left side of the phone above the volume buttons.

Hi i am have had a lot of trouble emptying my trash. when i go to put something in there it asks from my password and the item goes off the screen, but this does not clear any space on the hard drive.

Hi i am have had a lot of trouble emptying my trash. when i go to put something in there it asks from my password and the item goes off the screen, but this does not clear any space on the hard drive.

1. Triple-click the line below to select it:
~/.Trash
2. Right-click or control-click the highlighted line and select
Services ▹ Show Info
from the contextual menu. An Info dialog should open.
3. The dialog should show "You can read and write" in the Sharing & Permissions section. If that's not what it shows, click the padlock icon in the lower right corner of the window and enter your password when prompted. Use the plus- and minus-sign buttons to give yourself Read & Write access and "everyone" No Access. Delete any other entries in the access list.
4. In the General section, uncheck the box marked Locked if it's checked.
5. From the action menu (gear icon) at the bottom of the dialog, select Apply to enclosed items and confirm.
6. Close the Info window and test.

I have iPhone 6, 8.3. I cannot use bluetooth at all from my device, even to connect my macbook pro. I did all the recommended trouble shooting such as reboot and reset network settings. but it does not recognise any bluetooth device. Pls help.Thank

I have iPhone 6, 8.3. I cannot use bluetooth at all from my device, even to connect my macbook pro. I did all the recommended trouble shooting such as reboot and reset network settings. but it does not recognise any bluetooth device. Pls help.Thank you.

See iPhone BT profile on what can be connected/paired:
iOS: Supported Bluetooth profiles - Apple Support
And BT troubleshooting:
iOS: Troubleshooting Bluetooth connections - Apple Support

I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

Ok, sounds like the safe mode boot worked... You probably don't want to always be in safe mode though (some reduced functionality) so does it do a normal boot now? If not, you should then reboot into safe mode and run Disk Utility. Then select Macintosh HD on the left hand side, and click the Verify Disk button. If needed, it will ask you to Repair Disk. If there are errors found, Repair Disk again until there are none. Then try another normal boot and reply with result, wether good or bad.

The query does not reference any table when attempting to build the WHERE clause. (IES 00022)

Hi
I am getting below error.
The query does not reference any table when attempting to build the WHERE clause. (IES 00022)
This error is in Validating Measue object in IDT.
It is not throwing error for dimensions objects but only for measure objects.
My BO version is 4.1
Backend is Teradata 14.1.
Regards
Gaurav.

Hi
In the dimension/Measure definition, you can select the table. Find the below screenshot.
If you still getting the issue…Can you please share your screenshot, for better understanding the issue?

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

Similar Messages

Maybe you are looking for