I'm trying to restore my iphone and it has a error 1601 when its finished. what can i do?
I'm trying to restore my iphone and it has a error 1601 when its finished. what can i do?
Covered here:
http://support.apple.com/kb/TS3694
Similar Messages
-
TS3694 I have tried to restore my iphone and it has flashed up an error code - 3194, please help me?
I have tried to restore my iphone as it just turned itself off and now won't restart. So I tried to restore via itunes on the computer. It could not restore my phone due to an unknown error occurring (3194), please could someone let me know what I should do now?
I love my phone and I can't be without it!!!
HELP........http://support.apple.com/kb/ts4451
-
TS3694 I am trying to restore my iphone and keep getting the error message 3014?
I am trying to restore my old iphone for my daughter and keep getting error message 3014 - my itunes has the latest version uploaded?
Have you looked here?
-
I am trying to restore my iphone and im recieving 2003 error
need help restoring my iphone
receiving error code 2003 and not sure what to doErrors 3000-3999 (3004, 3013, 3014, 3018, 3164, 3194, and so on): Error codes in the 3000 range generally mean that iTunes cannot contact the update server (gs.apple.com) on ports 80 or 443.
Update to the latest version of iTunes.
Verify the computer's date and time are accurate.
Check that your security or firewall software is not interfering with ports 80 or 443, or with the server gs.apple.com.
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
An entry in your hosts file may be redirecting requests to gs.apple.com (see "Unable to contact the iOS software update server gs.apple.com" above).
Internet proxy settings can cause this issue. If you are using a proxy, try without using one.
Test restoring while connected to a known-good network. -
Someone please help!!
If it is done and just froze, then Reset, hold both Home and Power buttons until the iPhone begins to restart. Usually takes about 10 seconds of holding both buttons.
If still a problem. Then Restore again. I would reboot computer. Then open iTunes on computer. Then connect iPhone to computer. Then hold both Home and Power buttons until iTunes recognizes iPhone in Recovery Mode. Usually takes about 20 seconds time of holding both buttons. Then Restore the Firmware. -
I tried to restore my iphone and got a message saying an error 1002 occured, what do i do?
I tried to restore my iphone and got an error 1002. What does that mean and how can i fix my phone?
Click here > iOS: Resolving update and restore alert messages
Click 1002 on that page. -
my iphone 4 i bought was jailbroken to ios 6.0.1 redsn0w but i tried to restore the iphone and now it keeps saying connect to itunes but when i connect and try to restore an "unknown error" occurs and it will not boot up whatsoever. please help!
If you want to solve your problems, unjailbreak. And don't do it again, because jailbreaking causes problems as you read about in that article. You can try Recovery Mode: http://support.apple.com/kb/HT1808
-
im trying to restore my iphone and itunes doesnt allow it to restore without updating. problem is that i have the latest update on my iphone so why is it forcing me to wait for a 7hr update download when i already have the update and only need to restore?
Sadly, the iPhone 3G can not be upgraded beyond iOS 4.2.1.
-
im trying to restore my iphone and it got disconnected and wont reconnect to restore again, what do i do
Hi Troy,
Thanks for visiting Apple Support Communities.
You may find the troubleshooting steps in our iPhone assistant helpful if your device isn't recognized by iTunes:
http://www.apple.com/support/iphone/assistant/itunes/
Best Regards,
Jeremy -
Tried to update iPhone 4 to iOS 6 and my phone got stuck in recovery mode. My only option now is to restore my iPhone and lose media. However, I then tried to restore my iPhone and error 1603 occurred. My iPhone is now not working!?!?!
if your computer is not recognizing it, try using a different USB port or different usb cable. if that doesnt work you will need to uninstall and reinstall itunes.
-
I am trying to restore my iphone and it keeps telling me that the iphone cannot be restored. It also tells me that the iphone cannot do the requested rebuild, or something like that.
Open a terminal window and enter:
sudo vi /etc/hosts
You will be prompted for your login password, then you will see the contents of the hosts file in the vi editor. It should look like this:
# Host Database
# localhost is used to configure the loopback interface
# when the system is booting. Do not change this entry.
127.0.0.1 localhost
255.255.255.255 broadcasthost
::1 localhost
fe80::1%lo0 localhost
If there are any lines that contain "gs.apple.com" you must delete them. If you are not familiar with the vi editor:
press <return> until the cursor is on a line that contains gs.apple.com
type "dd" (without the quotes) (you won't see the dd as you type)
repeat until all of the gs.apple.com lines are gone
type ":wq" or "ZZ" (note that :wq is lower case and ZZ is upper case) -
i was trying to update my iphone and it downloaded the software but when it went to install it it turned off and wont turn back on and says i need to connect to itunes and ive tried but itunes doesnt recognize its there
Connect in recovery mode and restore, as described in this article:
If you can't update or restore your iOS device -
I am trying to restore my iphone 4s, but encountered 3194 error code. Would appreciate any suggestions.
Possibly something is blocking Apple through iTunes from approving your iPhone Restore. Sometimes this is due to your computer Hosts File redirecting your request away from Apple. Seach your computer for Hosts, open this file with Word Processor program. If there is any reference to gs.apple.com this is the problem. This name and the number with it needs to be removed.
-
TS3694 while trying to restore my iphone i am getting an error message 2001. what does that mean
Hello,
When I am trying to restore my iphone I a getting an error message that reads, " The iPhone "iPhone" could not be restored. An unknown error occurred (2001)."
What does that error message mean?
v/r,
A Concerned customerGoogle is your friend.
http://support.apple.com/kb/ts3694#error2001
Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software. If the errors persist on another computer and known-good USB cable, the device may need service. -
I had to restore my iPhone and lost a lot of music!!! How can I get it back?! No cloud appears next to the songs, just buy!
You should be storing everything on your computer and you should always backup your computer. Have you failed to do these things?
If so, not good, then you can redownload some iTunes purchases in some countries. Open iTunes store, click Purchased under Quick links
Maybe you are looking for
-
Can not test, run or debug from JDev 10.1.3
Hi, Just starting to play with latest JDeveloper 10.1.3 (installed latest version + patch), I've then created a new application (ADF BC + JSF), a new ViewObject and an app module. When I try to test the app module, I'm getting the following error: "C
-
"A plugin is needed to display this content", how do I get my computer to do this?
I am trying to open a video file for my online class. When I click on the file, a gray box appears and reads "a plugin is needed to display this content". How do I get my computer to open the video. I have a MAC and zero knowledge of how to fix probl
-
SMC(Solaris Management Console) problem
Hi I am trying to start SMC for managing the users and groups.But i am getting the following errors. bash-3.00# smc com.sun.management.viper.CriticalStopException: javax/help/JHelp at com.sun.management.viperimpl.console.gui.SMCConsole.start(SMCConso
-
Count of time to opening the customer's card in Siebel by SCOM 2012 R2
Hello! I need to know how long opens a customer's card in Siebel. It is possible to implement by SCOM 2012 R2? Problem for me is, the link doesn't open by GET method, is opened by javascript:.....(.....) Something like this https://[link]/start.swe?S
-
Setup of a standby and a streams - architectural question
Hi, I am thinking about a standby (prodstdby) for my Production (prod) database. For another part of the company we need to setup streams (HIS), this will copy only a part of the database ( some sort of archiving) to a database called HIS. During the