? i mac and mac book to detect an airport extreme base station!!!!

Help:
I am a new apple user. I just bought a mac book and iMac as well as the air port extreme base station (AEBS). I am presently using the AEBS w/my PC to get help.
I have tried to get both of my macs to scan, rescan to find the AEBS but they say one doesn't exist. I have restored the AEBS to its factory settings w/a hard reset an still no readings. Yes, the airport communication port is on.
It seems w/my PC it is plug and play something I would have expected w/apple, especially w/ their own products. My desk top and lap top PC's did not have any problem getting on line. I can only imagine if I did not have a PC to get on the internet I would be SOL.
Does anyone in cyberspace have any ideas what I need to do to get up and running? I hope I don't have some of the problem w/itunes as described in other communications. When I was hard wired via an ethernet connection to the macs all was well.
thank you

"Yes, the airport communication port is on."
When you say that does that mean in network settings on the macbook and/or the iMac you have gone in and turned on each respective Airport? If so, does it not list any available networks in your area? If so, you need to tell it which to connect with.
Go to your System Preferences > Network > Airport and be sure that it is turned on.
While there you may wish to tick the "Show AirPort status in menu bar" box, makes it a little easier to know current status, and find networks.
If the AEBS is working at all, both macbook and iMac should have no problem finding it.
Once it does, you can use Airport Utility to configure as you wish.

Similar Messages

Define static IP for both LAN and W-LAN devices with an Airport Extreme Base Station

Hey guys,
I have a lot of different devices connected to my Airport Extreme Base Station (5th Gen) either wirelessly or via ethernet cable. Since I control some of them via VNC and currently have to find the corresponding IP-addresses through trial-and-error, I'd like to define static IP-addresses for the computers in question. My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor. Two of the devices I want to remote-access are wired to a D-Link DES-1005D switch, which in turn is connected to the 1st ethernet port of the Airport Base Station. The remaining 3 remote clients are connected over 802.11n. All computers run Windows.
My problem now is that even though I was able to define static IP-addresses employing the "DHCP only" router mode, this didn't seem to work for the two computers connected via ethernet. Not only did I lose any internet connectivity with those, I even lost the ability to remote-connect to them using the VNC-viewer.
The question now is: how do I specify static IP-addresses for my ethernet devices correctly?
I hope you can help me.

My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor.
If you read the information in the other post, my answer would be the same here.
The Router Mode of DHCP Only is rarely used, and would only really be appropriate if your ISP was providing you with a fixed bank of multiple fixed or static IP addresses to use. This does not appear to be the case in your post.
If this were the case, the first IP address would be used as a Static IP address for your connection, and other devices on your network would receive the other fixed IP addresses.
99%+ of the time, you would use the Router Mode setting of DHCP and NAT on a network when you want the AirPort to perform as the main router for the network.
But......your post also indicates that you have another router upstream on your network from the AirPort Extreme. You would not want to run two routers in series on a network. That explains the problems that you are having.
The AirPort Extreme needs to be configured in Bridge Mode. It cannot be the "main" router on your network when you already have another router on the network. That is a fundamental networking rule.

Why no DSL and no cable respectively on new AirPort Extreme Base Station?

Hi,
I just saw the new APE Base Station, and I wondered about the fact, that it doesn't come with an ADSL2+- (for Europe) or cable-modem embedded, and being an full-featured router. I'd like to replace my adsl-router with the APE, but there would one more thing hang around here. Even the fact of missing 1000T isn't really good for me. Maybe next APE Base Station has some of the features?
Regards

Should I have set both networks with the same name, which I guess would alllow the various clients to default to whatever is the fastest?
Is that how it works?
Not the fastest, the best quality connection, which is a combination of signal strength, speed, low noise and who knows what else the Apple engineers have come up with for the formula.
The default setting for the Extreme is dual band, using the same wireless network name for both bands. This is the setting that most users should use because their device(s) will automatically connect to the best signal available depending on their capability and location.
You can "force" a connection to 5 GHz by assigning a different name to that band, but this does not assure you that you are making a better connection. It might well be worse.
Why? The upside is that 5 Ghz is capable of faster speeds. The downside is that you always must give up something to gain something else. In the case of 5 GHz, the signals are not nearly as strong as 2.4 GHz signals, so the 5 Ghz signals are going to be absorbed much more quickly by any walls, ceilings, or other obstructions.
To really get good perfomance on 5 GHz, you almost have to have a line-of-sight relationship between the router and the computer. So, 5 Ghz works well if you are relatively close to the router and you have a clear shot at the Extreme. Move your laptop down the hall and around the corner and chances are, the 2.4 GHz signal is stronger (and possibly faster) at that location.

Please help me connect eMac, cable modem, and Airport Extreme Base Station

I connected Ethernet cord from cable modem to Airport Extreme Base Station and then another Ethernet cord from Airport Extreme Base Station to eMac, but I could not get internet access on my eMac that way. I'm only getting internet access by directly connecting eMac to cable modem. Can someone please help me with a step by step explanation of how to set these 3 machines up so that I can have internet access on both my eMac and, wirelessly, on my new MacBook. Thank you very much in advance.
eMac & MacBook Mac OS X (10.3)
eMac & MacBook Mac OS X (10.3)
eMac & MacBook Mac OS X (10.3)

jenngee, Welcome to the discussion area!
Ensure that you power off the cable modem for a minute or so when you switch it to another Ethernet device.
Ensure that you are connecting the WAN port of the AirPort Extreme base station (AEBS) to the cable modem. The eMac should connect to the LAN port.
The steps for setting this up can be found in the "Designing AirPort Networks" (direct PDF link) document. Look through that document and try to get it setup. Then return here if you have more questions. Don't forget to post what you tried and the issues you encountered.

If I set up separate 2.4 and 5GHz networks on my Airport Extreme base station, is it possible to extend just the 5HGz network?

If I set up separate 2.4 and 5GHz networks on my new Airport Extreme base station, is it possible to extend just the 5HGz network with another AirPorrt Extreme that has duel, but not simultanous, frequencies?

Yes, configure the "extending" AirPort Extreme to connect to the 5 GHz network name when you set it up.
Temporarily, locate the extending AirPort Extreme close to the main Extreme for the setup, then move it to the remote location.
But, be advised that it is not easy to extend 5 GHz using wireless. You will almost need to have line-of-sight between the two AirPorts for this to work.

Setting up airport extreme base station with Mac and PC

I have an '02 iBook with an airport card installed and an airport extreme base station. my roommate has a PC and has the DSL connection in her room. i want to wirelessly network my iBook via the airport base. how do i do this? (my base was given to me without any manuals/disks etc)

Your Netgear wireless router is your network's base station. Your parent's PC will not be "serving as a base station" - its presence on the network isn't at all relevant to what you want to do.
To connect your G5 to the Netgear wireless router's network - click on your Mac's Airport menu, click on the name of your Netgear wireless router's network (it will appear in the list when you click on the Airport menu), and enter the wireless network password (if applicable) when prompted by the MacOS. That's is - you are connected!

Several PC and Mac connectivity issues with Airport Extreme Base Station

Hello,
This is not all necessarily airport base station related, but there is some crossover, so I'm posting all of these issues...
Here is the laundry list of things that I can't make work in a home network that contains a PC w/ XP Home, MacBook 1.83 w/ 10.4.7, and Airport Extreme Base Station w/ Modem.
1. Can't see the PC from the Mac.
a. "Connect to server -> Browse" does not find the PC
b. "ipconfig" on PC provides valid looking IP address
c. ping from mac to PC IP address times out
d. Firewall on XP is disabled via control panel
b. Windows file and printer sharing is enabled
2. Can't see mac from PC
a. Windows file sharing enabled on mac
b. Firewall on mac disabled
c. I used \\MacIPAddr\shortusername
d. ping times out
3. Using dial-up to access internet, how do i tell airport to dial using PC?
a. this feature is working fine from mac
b. If already connected (via instruction from mac), can surf the internet fine from PC
c. Is this even possible from the PC?
4. Can't see printer connected to base station from PC
a. See it fine from mac
b. How do i "find" the printer on the PC?
c. Is Bonjour required for this? (I don't have it on the PC yet)
5. Can't see a "shared" printer on the PC from the mac
a. printer is connected directly to PC
b. Mac's add printer wizardry looks like it may "see" the printer, but then it asks for username and password for PC. This is XP home, with no usernames or passwords. Single user. Nothing seems to work in the credentials pop-up dialog.
Any suggestions on any of these issues is very welcome.
Thanks

Is the PC running any kind of internet security or firewall software?
1. Can't see the PC from the Mac.
2. Can't see mac from PC
Sharing files between an XP PC and a Mac running OS 10.4.x
http://www.ifelix.co.uk/tech/3020.html
3. Using dial-up to access internet, how do i tell
airport to dial using PC?
Jon Sevy has a Java Utility for this purpose.
You will need Java in order to run the utility
http://www.java.com
4 . Can't see printer connected to base station from
PC
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express
http://www.ifelix.co.uk/tech/1004.html
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express using Bonjour
http://www.ifelix.co.uk/tech/1008.html
Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
http://www.ifelix.co.uk/tech/1012.html
5. Can't see a "shared" printer on the PC from the
mac
Printing to a printer on a XP PC from a Mac running 10.4.x
http://www.ifelix.co.uk/tech/3015.html
Printing to a printer on a Mac running 10.4.x from a Windows PC using Bonjour for Windows
http://www.ifelix.co.uk/tech/3014.html
iFelix

Wireless connection to internet with mac pro tower and airport extreme base station?

Hi, I have an airport extreme base station and a mac pro tower without a airport card. My internet wireless router is a great distance from my computer so I can't connect the base station directly to the router. I've attached the airport extreme base station to the tower via an ethernet cable, the base station seems to be wirelessly connected to the home network but the browser is showing "not connected".
Please help.
Thanks

Shouldn't the Airport base station be able to connect to it wirelessly?
It might be possible, but the Ethernet ports on the AirPort Extreme would not be enabled, even if it did connect to the Thompson' WiFi signal.
As Tesserax notes, among the Apple routers, only the 802.11n versions of the AirPort Express have the capability to "join" a wireless network with the Ethernet port being enabled.

New Mac and Airport Extreme Base Station User - Setup question

Good Morning,
I just received my new MacBook Pro yesterday along with the Airport Extreme Base Station. I was tying to setup the airport extreme but have had no luck. I want to make sure I'm connecting things correctly - make sure I'm not doing something stupid.
I have a cable modem and I previously had a Netgear router. The connection from the cable modem that had previously been connected to my Netgear router - I disconnected it and connected it to the Airport extreme base station instead. And then I plugged it in. Is that all the connecting that I need to do? I get the flashing amber light.
Now I did read a few other threads and it sounds like I may need to install the Airport Utility that came with the base station. So I'll try that when I get home tonight. But I would appreciate any other suggestions - especially whether or not I've connected the airport extreme correctly to my cable modem.
Thanks, Susan
MacBook Pro Mac OS X (10.4)

I want to make sure I'm connecting things correctly
The network configuration should look something like the following:
Cable modem > (Ethernet cable) > [WAN port] AEBSn > (wireless) > MacBook Pro
I have a cable modem and I previously had a Netgear router. The connection from the cable modem that had previously been connected to my Netgear router - I disconnected it and connected it to the Airport extreme base station instead. And then I plugged it in. Is that all the connecting that I need to do? I get the flashing amber light.
Since you changed your network configuration, you should perform a complete power recycle of your network components to allow enough time for them to "synchronize."
Modem/Router Power ReCycling
- Power-off the Cable modem, AirPort Extreme Base Station (AEBSn), & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AEBSn; Wait at least 5 minutes.
- Power-on the computer(s)
Now I did read a few other threads and it sounds like I may need to install the Airport Utility that came with the base station.
Yes, you will need this utility to perform the setup and follow-on administration of the AEBSn.

Mac Book pro can't connect to Internet through Apple airport extreme base station

I had problems connecting to the internet in the past with my macbook pro. One day it suddenly started working again but then I bought a second apple TV I lost connectivity. I have tried changing the IP address manually and while it shows me connected to the wifi I am still with out internet. When I hooked up the new Apple TV that I bought it booted my computer from it's ip address. The apple TV though wouldn't work and now nor would my computer. I ended up setting the Apple TV's ip address manually and now it works fine. My computer on the other hand does not no matter if I set it manually or not. Even if I plug in the ethernet cable from the base station it doesn't work. It show that it has a self assigned IP address. After I set it manually it shows that I am connected both via wifi and the ethernet cable but I can't connect to the internet. If I plug the modem directly into the computer bypassing the base station I get internet and it is using the IP address that worked originally.
It has something to do with the connection from the base station to my computer but this is odd considering every other device I have: iPhone 4, apple tv, apple tv, apple mini with retina display all work perfectly via wifi (newest apple tv had to be set manually as I stated above but now works fine). When I check the ip of the base station itself it seems to be different from the ip of the computer when the computer was connected directly to the router. I don't understand why my computer now can't connect to the internet via the base station whether it be wifi or by ethernet. Can you please help me trouble shoot this?
I have an AirPort Extreme base station which allows up to 50 users and a 30 meg connection speed.
I have a MacBook Pro (17-inch Early 2009), OS X Mavericks (10.9.2)

It has something to do with the connection from the base station to my computer
I don't think so..
I just posted a reply which totally vanished.. strange strange website now.
Please post some screenshots of your AE setup from the airport utility.. I want to see the summary page, then the network and internet tab.
Please tell us what modem you use.. is it a router??
If you have satellite or 3G wimax etc service they often are limited to 5 IP addresses... the AE takes one and then 4 more devices can join .. no more.
You need to also give us the screenshot of the IP you are getting in a computer that works.
EDIT
Sorry this is half double post.. the previous page refused to display.. now it has returned..

Airport Extreme base station no longer playing nice with Mac Pro

This is a strange problem...
I have an Airport Extreme base station (purchased in 2004) that I use with verizon DSL to get a wireless network going in my house, and I connect three computers wirelessly.
I have an ipod touch and toshiba PC laptop that are both able to connect to the network and run just fine. But lately (past 2 weeks or so) when I try to connect with my MacPro desktop I can go to a few sites, but after a few minutes the airport locks up. At that point none of my computers will connect and I have to unplug and then replug the airport. At that point the network will start up again and if I do not try to get on with Mac Pro then things run fine, but when I try to connect with desktop again, after another few minutes the same thing happens.
I know the problem is with the airport and my Mac Pro - I have done numerous connection experiments and have narrowed the problem down to that.
Is it possible that my MacPro might be drawing more power and causing the airport to overheat? (it is rather hot in the room with DSL connection)
Or should I accept that the current base it old, and bite the bullet and get a new base?
Any thoughts?

Could you post what you did in order to resolve the issue. I'm having a problem with the base station in that I cannot connect to the internet with my laptops (a mac and pc) while I can connect wirelessly to my network with my desktop (G4). The base station is not detected in the base statin admin utility or the aiport setup utility. If anyone else has a solution I would be much obliged to read it.
Thanks!

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

Ip8500 does not print with XP & Airport Extreme Base station (OK with Macs)

My canon ip8500 is connected to an Airport Extreme Base station. I can print from either Mac (a G4 and a new iMac 24") but no luck with either XP laptops (accessing the internet is no problem). I've installed both PC's with Bonjour but after a minute or so I get a failed to print message. Any suggestions?

They are simply obsolete. You cannot update their firmware to be compatible with new products. Buy something to replace them such as a couple of new Airport Expresses.

Configure TC and Airport Extreme Base Stations with different channels

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

How do I configure an Airport Extreme base station to receive and distribute a wi-fi network from a broadband wireless router?

I have recenly upgraded my broadband service and now have a wireless router. My old network configuration was a router connected by ethernet cable to an Airport Extreme base station which then broadcast my wireless network (I also had an Airport Express base staion set up as a wi-fi booster elswhere in the house).
I now have two networks (my original network and the new network from the wireless router) and wish to amalgamate these into one.
Ideally I wish to use the Airport Extreme base station as the "remote" booster (I have purchased Powerline adapters for this purpose) but don't know how to configure the Airport Extreme base station in order to to this.
Can you advise on the best set up for this please?
My Mac is running OS X 10.8.2 and the Aiport untility is version 6.1.
Thanks in anticipation.

The AirPort Extreme should be configured to "create a wireless network" with the same WiFi network name, security type (usually WPA2 Personal) and password as your existing router. It should be configured as connection type Ethernet and be in bridge mode.

? i mac and mac book to detect an airport extreme base station!!!!

Similar Messages

Maybe you are looking for