I Mac G5 locks up and wont boot up

I have been having a problem with my 2005 IMac G5. It has been an ongoing problem since I bought the computer. The problem starts when the computer locks up and needs to be powered down, after which it will not boot up again. I get a gray screen with a flashing ? mark and the fan goes into hyper drive. I have tried all the tips in troubleshooting; resetting the PR, looking at the led lights, etc. It will not start up in safe mode.
While it was under warranty, the apple store replaced the hard drive and re-imaged the hard drive several times. Since it is out of warranty the only thing the store will do is re-image the hard drive which fixes the problem for maybe a day or two and then the computer locks up again I have the maximum amount of memory in the machine so when it is working it is fast. I heard there was a problem with the airport wireless card in these machines. Could that be the problem or could the hard drive be bad? I hate to throw this computer away because it was hardly used. Thanks for any comments.

Don't throw it away, clone the drive to an external and then put a new drive in the iMac, and then revere clone from your external.

Similar Messages

  • I just installed new 8gb ram in my MBP 2010 and it beeps 3 times and wont boot.

    I bought 8gb DDR3 1066 mhz to install on my MBP 2010 and it beeps three times during boot and wont boot. I looked at other threads and it seems like no one has found an answer. It looks brand new with no obious problems.

    Macs can be very fussy about RAM... It is Important to get the Correct and Matching RAM
    You can use these Links to check which RAM is suitable for your Mac...
    http://eshop.macsales.com/shop/apple/memory/
    http://www.crucial.com

  • My iPhone4 version 5.1.1 is stuck at the reboot(the spinning circle) screen and wont boot up, suggestions people?, My iPhone4 version 5.1.1 is stuck at the reboot(the spinning circle) screen and wont boot up, suggestions people?

    My iPhone4 version 5.1.1 is stuck at the reboot(the spinning circle) screen and wont boot up, any suggestions people?

    Try holding both home and off buttons for a few seconds until the apple logo appears on screen. See if that solves the issue. Honestly, there may be a myriad of reasons why your phone may be stuck at boot stage. Care to share what you did before it occured? That would help us give you better troubleshooting.

  • My Mac Pro flashes the question mark and wont boot from hard drive, flash, or Cd... Please help!

    My Computer froze so I shut it down... When I tryed to boot up again it wouldn't power up.  After a few tweeks I got it to power up but now it wont boot from the hard drive, flash drive or a cd.  It want to start, then, after a few seconds it stops.  Not sher what to do.  Can anyone help?

    Have you tried Safe Boot?
    You also might reset PRAM and reset SMC.
    Have you tried booting with the Recovery System? See its possibilities here.
    From there you can make repairs to your primary startup partition.
    Do you have a backup? If not, do you have an external drive large enough to back up your primary drive? It would be good to have one in case your drive needs repair or replacement.

  • IMac problem, keep freeze and wont boot

    my iMac was updating latest iphoto raw compability update,
    then my imac turn into around 3 hours machine that frezee up after 3-4 hours of normal used (itunes and brosing),
    and it wont shutdown, I force the power button to make it off.
    after that,
    it wont boot to mac osx SL
    flashing folder with question mark on it appear.
    but I certainly could boot from SL installation DVD,
    I have to wait half to one hour for normal start up again,
    if less than half hour, it wont boot to mac osx..
    how strange is that?
    I have to wait everytime..
    can anyone fix this?
    I thought this problem connect with my bootcamp with win7,
    because I can't boot to win7 also,
    I have tried to disabled auto mounting NTFS with fstab, it wont solve the problem at all,
    anyone can help me?
    is format it all will help?
    Message was edited by: Hudi

    Before deciding that you can't replace the drive yourself, visit the following site and find the step by step instructions for replacing the drive yourself:
    http://www.ifixit.com/
    If you see the instructions and feel that you can replace the drive yourself, you will save money that way. I'm not that familiar with modern iMacs, but I know it was very easy to replace the drive in my old iMac. It may not be as hard to do as you think. If you want extra help, you can post questions on the iMac forum.
    If you still don't feel like it is something you can do yourself, try looking for an AASP (Apple Authorized Service Provider) in your area and see what it might cost to have the AASP do the replacement. Often an AASP can do a repair for less money than Apple, and they will usually be willing to install a drive that you have obtained elsewhere for a reasonable price. From what I have read on these forums, many people have used AASP's to install bigger and faster drives on their machines.
    Definitely contact Western Digital about your drive. Usually WD drives come with a 3 year warranty, and if the drive fails before then, WD will replace the drive. KT has mentioned that the drive apparently is not under warranty, but might qualify for some sort of an upgrade. Before shopping elsewhere, check to see if this upgrade might entitle you to a very good deal on a replacement drive or something of that nature.
    Good luck!

  • 2008 imac - beachball lock ups and no-boot 'question mark in file' issue

    Firstly apologies am new to this forum.. am happy imac user (2008) but recently my imac is freezing in use and/or failing to boot on startup; the grey screen showing for a bit and then a file with a question mark in it.  This now happens frequently and I find my self having to wait hours before my mac will boot.  I have looked through forum responses and tried disk repair utility, but that showed no problems other than repairing a few permissions - also downloaded and run EtreCheck - but again nothing obvious, although I'll readily concede I don't really know what I looking for.  Before I sadly head off on a long journey to a Genius Bar appointment maybe for a new hard drive?? Can anyone suggest anything please - all advice welcome. Thank you

    Hi triffiid,
    I'm sorry to hear about the issues you've been having with your Mac. If you are currently booting to a grey screen with a flashing question mark, you may find the troubleshooting steps outlined in the following article helpful (apologies if you have already seen it):
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/ts2570
    Regards,
    - Brenden

  • HP DV4-1155SE Black Screen and Wont Boot. Please Help!

    Hello all I am working on an Hp DV4-1155SE. I have tested the memory modules, the hard drive and everything else that I can take out of the computer easily. Everything works but!, The laptop will not boot into the bios or anything else. Black screen, wont boot and i have the bios file that HP supplies on the support page of the site. I have looked at the instructions that a few people have posted about re flashing the bios and that does not seem to help me at all with this AMD processor. If anyone can please offer any help at all this would be greatly appreciated.
    Thank you!

    I will search on int 19h....thanks.
    My problem started before the bios-screen.
    This is what I tried this evening:
    - Disconnected all non-essential devices...no effect.
    - Cleared the CMOS...system booted to OS!    Screens still garbled! 
    - Put in an older graphics-card...No artifacts! 
    - Put my MSI NX6600GT (AGP) back in...screen grabled while booting. Once in OS everything
      looks fine at first. Later I noticed some odd random pixels. Playing movies is working fine.
      Playing 3D games results in all kinds of strange looking artifacts.
    - Installed the latest NVidia- drivers...no effect.
    Is my problem still MOBO related or Graphics Adapter?
    Any further advice?
    Thanks!

  • MacBook Pro hard disk noise, froze and wont boot

    I was using my MacBook Pro and it froze at the same time I could hear the hard drive cracking. The following are guesses because of the sounds I was hearing: While the hard disk made cracking noises, it would stop spining. Then it started to spin again and another crack would stop the spining.
    I held down the power button to shut down and now it wont boot. I can hear the same type of noises I described before.
    Thanks for the help

    Based on your comments, your HDD is dead.  Get a new one, larger and faster if can afford it and swap in your MBP.  You will have to reinstall your OS and I hope you have a back up of your data.
    Caio.

  • My iphone 4 is locked up and wont sync to itunes what do i do, my iphone 4 is locked up and wont sync to itunes what do i do

    my iphone 4 is locked up and cant remember my passcode and it wont sync to itunes how would i restore it and my lock button dont work

    power down your phone and unplug from your computer
    hold down the home button then plugin and wait till you get a message about an iphone in recovery mode
    follow the instructions on screen to restore your phone
    (this will wipe out your phone but it is the only option other than remembering your passcode)
    in the setup screen after its restored you can restore information from icloud or a backup given you have one

  • Touchpad randomly locks itself and wont unlock on Satellite P50-A

    Don't know if anyone can help me out but i recently bought a P50-A laptop and i am having issues with the touch-pad.
    Basically what is happening is that every now and then my touch-pad randomly locks itself and then wont allow me to unlock and will unlock once I have reset the laptop.
    I have checked the drivers and everything appears to be working fine and there appears to be no hardware conflicts.
    Has anyone else had this happen to them?

    Please check this Toshiba document about available touchpad settings under Windows 8
    http://aps2.toshiba-tro.de/kb0/HTD3101Z30000R01.htm
    I recommend disabling or changing the PalmCheck settings within the touchpad pointing area.
    Greets and feedback would be appreciated.

  • Why is my ipad 4 suddenly going back and forth between the logo screen and lock screen and wont reset when i hold the power and home buttons down? please help, apple store is very far from my house

    my ipad has never been dropped or overheated, but suddenly the screen went to the lock screen and then the logo screen and it keeps doing that. i tried resetting but its unresponsive. is this a common issue with ipad and whats wrong with it? i was checking the AccuWeather app when this happened and my battery was full if that helps. thanks

    Thank You, thank You ...so much......that feature made me crazy!  
    Ocean20 wrote:
    This can be turned off in settings/accessibility/zoom. Then on the next screen turn off

  • Wifi connection has lock on and wont connect how to take lock off

    wifi has lock on the homehub connection, how do I take lock off and how do I prevent this from happening again i am unable to connect to the internet

    You will neeeeeeeeeeed to go to Apple and have your phone serviced.

  • Power mac g4 MDD put a second hard drive in it and wont boot up with it in

    hi i have a second 150g hard drive i just put in my powermac and it will not boot up with it im kinda new to this which is why i bought an a MDD to **** with but i probably shouldnt have done this but i booted the computer up with out the new hard drive plugged in and then plugged it in and its just sitting their with the color wheel going i picked the harddrive up off ebay and it says it will work on a mac is their something im missing here

    HI there, likely it's just the Jumper settings on the New HD, set it to Cable Select or Slave if it's in the middle of the cable & the Other one has Jumpers set to Master.

  • Mac Pro Locked Up and Now  One Video Card and Audio Not Working

    Last night, my Mac Pro totally locked up to the point I had to power it off to get it to do anything. When restarted, one of my video cards and my audio are no longer working. I have dual monitors so tried switching the connections to see if it was the monitor and that was not the problem.
    I tried doing a formal shutdown after the restart and this also did not clear up my problem.
    Everything was working fine prior to the lockup. Any suggestions would be much appreciated.

    If you've added RAM and are using the nVidia 9400m video driver, you may be using incompatible RAM
    http://www.nvidia.com/docs/IO/60555/MemoryCompatibility_List_DA-04576-001v01.pdf
    My wife's MB is locking up when watching videos; hulu, iTunes, VLC. The above is the only answer I've found.
    BOL

  • Bought ram for Macbook 4,1 and wont boot up

    Hey guys i just bought some new ram to upgrade my macbook 2.1 Ghz Intel Core 2 Duo running Snow Leopard 10.6.8 and it says its the right ram for it but it doesnt boot up. the RAM i bought is 2GB PC5300/667Mhz DDR2. i bought 2 modules to equal 4GB and it doesnt boot. i tried one stick, both sticks, one new and one old, still nothing. the disk drive runs but thats all. So either i got bad ram or they labled it wrong? What can i do besides return it?

    If you bought your RAM at a place that also sells PC RAM you may have gotten mislabelled RAM. PCs can handle different RAM speeds so they’ll often label higher speed RAM as a lower speed rather than make two different speeds of RAM. But Macs are much more picky. They require a RAM stick to be exactly 667mhz not 675mhz or 800mhz. The way to tell is to put one of your old RAM sticks in and it will force the new RAM to run at the correct speed.
      This is from one review of PNY RAM:
    "These modules are actually 800Mhz. PNY no longer makes or sells 667Mhz modules. Not all computers that require 667Mhz are compatible with 2 800Mhz modules. They refuse to down clock properly. This is especially true with a number of Core 2 Duo MacBooks. Spoke to PNY support, they flat out told me that yes, they sell 800Mhz modules in 667Mhz packaging. If you RMA a module that is 667Mhz (or supposed to be 667Mhz) they will replace it with an 800Mhz module as they no longer have any 667Mhz SODIMMs, not even for RMA replacement!"
    These are good online stores for Mac compatible RAM
    OWC 667Mhz RAM
    http://eshop.macsales.com/shop/memory/MacBook/DDR2/ - They offer Mac tested RAM at very good prices.
    Crucial Memory http://www.crucial.com/ - good place to buy RAM from all over the world. They also have an excellent memory selector that allows you to choose memory based on your computer's model
    Data Memory Systems http://www.datamemorysystems.com/apple-memory.asp - another good, cheap place to buying RAM if you live in the U.S.

Maybe you are looking for

  • Javax.xml.rpc.JAXRPCException: Cannot unmarshal jaxrpc-mapping-file:

    Hi, I am using jboss for deploying the webservice. when i am deploying the webservice i am getting following error. 20:26:30,696 INFO [WSDLFilePublisher] WSDL published to: file:/C:/jboss4.0/jboss-4.0.0/server/default/data/wsdl/acWebSe rvices.war/Add

  • Transactions used in simple file-idoc scenario

    hi all, what are the transactions used in idoc scenario...(Ex: idx1 for creating new idco) let me know what is the transaction code to find the clients available... Is it 'SCC4' Please provide me required info Thanks Narasimha Edited by: Narasimha bo

  • Recurring invalid volume file count (I repair, it comes back)

    On my desktop system (10.6.8), every once in a while Disk Utility says there is an invalid volume file count  (off by 2) and an invalid volume directory count (also off by 2). I boot off the DVD, use Disk Utility to repair the file system, and a coup

  • Maximum Contract Size

    Hi - working at a multinational client who want to create what to me seem like very large contracts in SRM 5 and ECC6 - by very large I am talking 10's of thousands of lines. In addition, they want the option of maintaining (at the very least) scale

  • User defined metrics for alert log errors

    I want to create UDM for getting the full description of alert log ORA -  error to be reported via E-mail.  Can somebody guide me or help me withe script which can be used to create this alert.  Currently, We get the only the message of  that error i