I need a bluetooth transmitter compatible with MW1

i need a bluetooth transmitter compatible with MW1

Smart Wireless Headset pro, MW1 can be used to make calls, receive text and email notifications, listen to FM radio, stream music from your Android Smartphone and more.
You can view the list of compatible Smartphones from the below link.
http://store.sony.com/webapp/wcs/stores/servlet/ProductDisplay?catalogId=10551&storeId=10151&langId=...
Also, Sony Mobile phones have their own separate community and so are best qualified to address any issues or questions you may have on Sony mobile phones and its accessories. You can visit the Sony Mobile Community here:
http://talk.sonymobile.com/community/support
If my post answers your question, please mark it as an "Accepted Solution."

Similar Messages

Should I get a 2.0 or 3.0 USB external hard drive for my 2011 Macbook Pro? I need it to be compatible with the USB ports of both a PC and a Mac.

Should I get a 2.0 or 3.0 USB external hard drive for my 2011 Macbook Pro? I need it to be compatible with the USB ports of both a PC and a Mac. I was thinking of getting a Seagate becuase apparently it is compatible with both systems, but I want to know which would be a better investment.

Using USB 3 devices on Mac computers FAQ

Hi, How do I communicate CANopen device with anyother CAN device? What things needs to be made compatible with 2 CAN devices to communicate?

Hi,
I have to communicate CANopen device with other CAN device which uses GMLAN.
So in general, How do I communicate CANopen device with anyother CAN device?
What things needs to be made compatible with 2 CAN devices (i.e, one is CANopen and anyother CAN device) to communicate?
Please reply.
Thanks,
Najmu

Hello,
The two devices need to be connected with a CAN cable and while carrying out the communication, one device should be the master and the other should be the slave. Also you should maintain the same protocol (Baud rate, Arbitration ID etc.) at the two devices.
Regards
Akshat Jain

JABRA A320S bluetooth dongle compatible with my mac book??

I bought a jabra a320s to pair my mac book with a sony mini stereo. i want to play my music through it.
i had to get the jabra dongle since the mac's bluetooth didn't support a2dp. i haven't opened the box yet for the jabra device. will this work with a mac? on the box it only says compatible with various windows, etc.
anyone know if this will be fine for what i need? thanks in advance.
Message was edited by: illinny

The Mac Book is from 2005..When I tried looking up the Bluetooth specifications it didn't list A2DP as a feature.
It doesn't list A2DP as a feature on the very latest MacBooks either - even though those are the ones that come with Leopard which does have A2DP support. A2DP is a feature of the Macs Bluetooth system software, not the Bluetooth hardware. That's why older Macs updated to Leopard have gained A2DP support, with no new Bluetooth hardware required.
So if the bluetooth on this computer doesn't have A2DP then there's no way for me to use a bluetooth dongle instead?
No. But it wouldn't matter if you could use the Bluetooth dongle. You would still need the updated Bluetooth software on the computer for A2DP support - which is part of Mac OS X 10.5 Leopard.
I find that hard to swallow.
Well, try it for yourself if you don't believe me.
I should just be able to disable the internal bluetooth and use the dongle, right?
Well... Yes, if there was actually a way to disable just the internal Bluetooth - but there isn't. If you were to turn Bluetooth off in the system preferences, it would turn all Bluetooth off, including the dongle.
But lastly, does anyone know if the Jabra dongle would be compatible with the Mac Book if I actually busted open the box?
You're not reading what I've written are you? As the MacBook *already has* internal bluetooth hardware, you cannot use an external bluetooth dongle with it. The internal bluetooth always takes priority over the external, and you cannot turn off just the internal Bluetooth.

Need an external HD compatible with OS 9

Can anyone recommend a good External HD compatible with OS 9 (160GB - 500GB). Thanks for your help

Hi, coolins -
Yes, they are easy to use. An external hard drive can be used just like a large floppy - you can drag and drop files to it, or save files directly to it via simple navigation in the Save or Save As dialog window. You can copy a multitude of files at once - select a group of files, folders, or mixed files and folders on your internal hard drive and drag the group to the external drive; Finder will copy (not move) the group to the drive.
As far as setup goes, although the drive may come preformatted for a Mac (or not; most won't), it should be reformatted before you use it. Unfortunately, OS 9's Drive Setup utility (which can be used to do that for internal drives) is not capable of formatting an external drive. Some drive manufacturers will furnish a formatting utility with their drive; for those that don't, you will need to use a 3rd-party utility. The one that I use is the VST formatting Utility. Another option is to use a machine running OSX to do the formatting - OSX's Disk Utility is capable of formatting a firewire (or USB) drive. In any case, be sure to select Mac OS Extended (also called HFS+) as the format for the drive.
Once the drive has been formatted it will appear on your desktop as an icon, on the right-hand side where all drive icons (those for hard drives, floppies, aip drives, CDs, etc.) appear. You can open it by double-clicking it; change its icon; and even rename it (provided File Sharing has not been enabled for that drive).

Is there a wireless fm transmitter compatible with otter box?

I have an iPOD touch 3G with an otter box. I want an FM transmitter (preferably one that can also charge, but not necessary). I bought one that fits the docking port, but it is not long enough to connect into the port slot if I have the iPOD in the otterbox. I don't want to have to take the ipod in & out every time I want to use the transmitter. Nor do I want my ipod unprotected. Is there a transmitter available with a longer port connector?

I have looked for a while and not found anything ... the Touch shape means the connector slot is located up the back further and so many of the covers that go around the bottom do not allow connection ... unless you pull the cover off. A longer connector pin would do the job but noone does them. Bad design on the part of Apple and cover manufacturers.

I need a photo printer compatible with Mac OSX Yosemite 10.10.2

I want to buy a printer/scanner which gives good colour photo prints, airprints with my iPad and is compatible with my mini mac which uses OSX Yosemite 10.10.2. The sales helpline is closed for 4 days so suggestions as to options would be much appreciated., Thanks

Dear EdinburghRox,
You have this options:
http://store.hp.com/webapp/wcs/stores/servlet/us/en/mdp/printers/envy-4500-100060--1#!&TabName=vao
http://store.hp.com/webapp/wcs/stores/servlet/us/en/mdp/printers/envy-5530-100059--1#!&TabName=vao
http://store.hp.com/webapp/wcs/stores/servlet/us/en/mdp/printers/envy-5660-122508--1#!&TabName=vao
I hope you find it helpful.
Greetings.
* I am not an employee of HP, my work is voluntary.
If this answer was helpful and clarify or resolve your problem, please mark the issue as resolved and click my star next to give a kudo as thanks.
I am not an employee of HP, my work is voluntary. If this answer has been helpful and clarifies or solves your problem, please click the button
and click on the icon if you want acknowledge the assistance.

Brookstone Bluetooth keyboard compatible with os7?

I cannt get my ipad to find my brookstone Bluetooth keyboard since I updated to OS7. Anyone know if it is still compatible?

Hey there Patricia,
Thank you for using Apple Support Communities.
If you cannot pair the Keyboard with the phone via bluetooth, I want to recommend this article:
iOS: How to troubleshoot Bluetooth connections
http://support.apple.com/kb/TS4562
Check that you are in range of the Bluetooth device with which you are trying to pair your iPhone, iPad, or iPod touch. Most Bluetooth devices have a range of approximately 30 feet.
On your iOS device, tap Settings > Bluetooth and find your device in the list. If your device says Not Connected, tap the name of your device to attempt to connect it.
Tap Settings > Bluetooth and turn Bluetooth off and then on again.
Make sure that your Bluetooth accessory is turned on and fully charged or connected to power.
Restart your iOS device.
Tap Settings > Bluetooth and locate the Bluetooth accessory you are currently connected to or attempting to connect to. Then tap and Forget this Device. Try to pair your Bluetooth accessory again.
Note: You may need to re-enter your Bluetooth accessory PIN if your accessory requires one. Some common PINs are 0000, 1111, and 1234.
Restart your Bluetooth accessory by turning it off and then on again1.
Update your device to the latest version of software. See how to update your iPhone, iPad, or iPod touch.
If your Bluetooth accessory has upgradeable firmware, check to see that you have the latest version1, 2.
If that does not resolve the issue I would try these steps from down the bottom of the article:
Unable to pair to a Bluetooth accessory
If you see the word "Connected" next to a Bluetooth accessory in Settings > Bluetooth, your iOS device is already paired to a Bluetooth accessory. Remember, you can only connect to one Bluetooth accessory at a time.
If your Bluetooth accessory requires a PIN for pairing, be sure that you are entering the correct PIN1.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings.
Note: This will reset all network settings including: previously connected Wi-Fi networks and passwords, recently used Bluetooth accessories, VPN and APN settings.
Cheers,
Sterling

Nokia Bluetooth Headset compatible with Nokia Char...

Hi friends,
I need your help...i have a Nokia Bluetooth Headset BH-801 and a Nokia N70 with AC-4 charger...
My question is...the AC-4 charger works/charge my Nokia Bluetooth Headset BH-801 without any problems???
Thanks all =)

The original charger is the AC-3...so no problem right???
Thanks a lot =)

Bluetooth keyboard compatible with Powermac G4?

Can I use a Bluetooth Keyboard (model iWantit IKBBTWH13) with a Powermac G4. If not, any suggestions, apart from throwing away the Mac? Thanks.

You can purchase a USB Bluetooth adapter that can give a PowerMac G4 Bluetooth connective capabilites.
Here are a few.
http://eshop.macsales.com/item/IOGear/GBU321/
http://www.amazon.com/Kinivo-BTD-300-Bluetooth-3-0-adapter/dp/B005Z5HT2M/ref=sr_ 1_1?ie=UTF8&qid=1392357288&sr=8-1&keywords=usb+bluetooth+dongle+mac
http://www.amazon.com/IOGEAR-Bluetooth-Micro-Adapter-GBU521/dp/B007GFX0PY/ref=sr _1_3?ie=UTF8&qid=1392357406&sr=8-3&keywords=usb+bluetooth+dongle+mac
http://www.amazon.com/D-Link-DBT-120-Wireless-Bluetooth-Adapter/dp/B00006B7DB/re f=sr_1_12?s=pc&ie=UTF8&qid=1392357456&sr=1-12&keywords=usb+bluetooth+dongle+mac
http://www.amazon.com/Kensington-Bluetooth-USB-Adapter-33085/dp/B0001Q5SZ0/ref=s r_1_5?s=pc&ie=UTF8&qid=1392357456&sr=1-5&keywords=usb+bluetooth+dongle+mac

BH-100 headset (bluetooth) compatible with PC?

Hi!
I want to know if my BH-100 headset (bluetooth) is compatible with my PC (at least like a microphone)?
I've have just bought a new bluetooth USB adapter for my PC. It recognizes my headset but I don't see services available for my headset....
Thanks for the help!
TAG4

Best to check that your Bluetooth adaptor supports Hands Free Profile for voice and is not just data transfer.
If it is a USB adaptor, is the pc sound card linked to the USB port?
Hope this helps

I need a step motor and controller compatible with LabView Can you recommend any

I need a step motor compatible with LabView and I thought i would check with you before i moved forward in my experiment

Dear chapbs,
I've attached a sample cart below to show you the components for a possible setup of your system. Keep in mind that whatever stepper drive you purchased would power your motor. If you go ahead with the purchase of a controller & drive, I would highly recommend contacting NI to insure that you purchased the correct accessory components and cables to connect & power the components. I hope the sample cart is helpful. I created it by browsing ni.com, adding items to my cart, and then saving the cart to an excel file. Please post back if you have additional questions.
Best Regards,
~NH
Attachments:
SampleCart.pdf ‏145 KB

How do i find out if a cpu processor is compatible with my laptop?

I have a 2000-2a22NR Notebook PC and I want to upgrade my cpu. Right now it has a 1.4GHz AMD Dual-Core Processor E1-1200. I want to put one in that has at least 2.6 GHz or more but I cant seem to find out if I even can or witch ones will work. I can find the specks here on hp but it only says what I have not if I can or witch ones are compatible. I know that some notebooks cannot be upgraded this way and I know if I can I need one that is compatible with mine. What I need to know first off is IF I CAN and if i can i need either a list of ones that will work or something to refer to when I go to buy one. PLEASE PLEASE PLEASE DO NOT TELL ME TO LOOK IT UP!!!!!!!! I have been trying to all day long. HOURS i have spent just trying to find out if i can so any help would be greatly appreciated. Thanks in advance to anyone who helps me it means a lot.
This question was solved.
View Solution.

Here are the specs for your HP 2000-2a22NR Notebook Computer. Here is the HP 2000 / Compaq CQ58 - Maintenance and Service Guide for your computer. Compatible CPUs are listed on Page 1, Section 1, Products description under AMD models. CPU upgrades only valid on models with Intel processors. On AMD models, the processor comes with the system board and cannot be removed. Look it up!!!
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Is the BlueAnt V1 compatible with the iPhone 4?

I'm trying to pair my BlueAnt V1 to my iphone 4. I've tried to do a search to see if this bluetooth is compatible with the 4, but I can't find anything saying it's not. However, my phone isn't detecting the headset. Can anyone help? Thank you!

in general headsets have to be put in pairing mode before the pair make sure you have don that

Recommendations for wireless mono laser printer compatible with OS 10.6.7?

I am looking for a wireless mono laser printer compatible with Snow Leopard OS10.6.7. This is to be shared by 4 Macs in a small office. We are connected to the internet via DSL modem (2 wired, 2 wireless), and communicate with the Bonjour network. We have a Time Capsule, but are not using that for a server at this time. Any suggestions would be much appreciated.

How long is a piece of string?
There's a myriad of compatible printers that meet your given criteria, but that's mostly because you haven't been very specific about your needs... 'compatible with 10.6.7' is just one of many considerations.
For a start, what's your budget? That may narrow the field considerably.
Then what's your expected print run? If you're printing tens of thousands of pages per month your needs are way different from someone printing one or two pages a day (or week!). There's a reason why printer manufacturers list a 'duty cycle' on their spec sheets - it tells you what they think it's capable of handling so that you don't under or over-spec your printer.
And 'duty cycle' is way more than just the speed per page - it's how quickly the components wear out and need replacing. If you print 10,000 pages per month then the manufacturer has to build using higher-grade components that can run for hundreds of thousands of pages before servicing/replacing (and I'm talking here of things like fusers, belts, and the like, not consumables like ink and toner).
On the other hand there's no point in the manufacturer using high-grade components that can handle 1,000,000 cycles in a printer that's printing 100 pages a month - the printer, your computer and probably even you would be obsolete way before those components wore out.
Then you need to consider input capacity. If you're printing a lot you'd probably appreciate high-capacity input bins (so you don't have to walk over to the printer every hour to refill the tray).
What about duplex? Do you want to be able to print double-sided (either now or in the future)?
Since this is a small office, do you want other multi-function features such as fax/scan/copier?
These questions (and probably more) will go a long way to identifying the 'right' printer for your needs. As it stands, though, there really isn't enough data to offer any advice.

I need a bluetooth transmitter compatible with MW1

Similar Messages

Maybe you are looking for