I need a high speed digital I/O solution!

I'm looking for the following digital I/O recording solution:
16 channels input
100MHz sampling rate
Able to acquire 1 sec of data at 100MHz
Does anyone know of hardware that can do this? I would prefer somekind of PCI card to a desktop logic analyzer.
Thanks in advance.

Hi,
Unfortunately, the fastest DIO card available can not be clocked at 100MHz. Even if there is a card that can tolerate the above rate, most PCI Buses have a 132 MB/s bandwidth, and clocking data across it with the above rate is not feasible.
Regards,
RamziH.

Similar Messages

Continuous High Speed Digital Acquire- Monitor SPI data lines

Hi
I need to monitor a serial interface that runs at 5-10Mhz of SPI protocol.
I am using a PCI 6534 with upto 20MHz capability. I have access to Chip Select, Data In, Data Out and SCLK.
Valid Data is sent when Chip Select is low.
I have tried start trigger (ACK) when chip select low and stop trigger (REQ) when chip select high however have been unsuccessful to acquire all data.
I need to be able to trigger off the chip select line going low and then read digital lines (Data In , Data Out, SCLK) until chip select then goes high.
Once i have acquired all data (Packets of 8 bytes - 40bytes), i will then need to decode the output.
Can anyone help please?

Seamus
I have previously used a 8451 device to drive a SPI circuit, however for this application i just need to monitor 4 digital lines, (i cannot interface or drive the lines i have to monitor / decode them).
I have found many examples of acquiring data from digital lines however i need to trigger of a signal then start acquring all data on the other lines.
I can use digital start trigger for chip select falling edge and stop trigger on the Chip Select rising edge. When trigger found data of 4 lines needs to be stored then decoded.
Thanks

Do you need a high speed USB drive to effectively use a 5G ipod

My new 5G is working on my newer dell comp with the high speed, but not working on my older vaio without a high speed drive. Thoughts?

My new 5G is working on my newer dell comp with the high speed, but not working on my older vaio without a high speed drive
Do you mean a high speed (USB 2.0) port?
Your hard drive is not USB and it is fast enough.

Just installed Yosemite (MacPro15 End 2011), the fan is working on high speed since! any solutions?

I just installed Yosemite (MacPro15 End 2011), the fan is working on high speed since!
Is there anything I can do? On Maverick the mac worked just fine and very silently, so I assume that the new system does something wrong?
Can anybody offer some help?

Hello Csound1
here is the report
roblembeschreibung:
Update auf Yosemite, Lüfter läuft mit max frequenz, CPU Temperatur ca. 95 °c
EtreCheck version: 2.0.6 (91)
Bericht vom 20. Oktober 2014 16:56:47 MESZ
Hardware-Informationen: ℹ️
MacBook Pro (15 Zoll, Ende 2011) (Verifiziert)
MacBook Pro - Modell: MacBookPro8,2
1 2.2 GHz Intel Core i7 CPU: 4-core
16 GB RAM Nachrüstbar
BANK 0/DIMM0
8 GB DDR3 1333 MHz ok
BANK 1/DIMM0
8 GB DDR3 1333 MHz ok
Bluetooth: Älter - Handoff/Airdrop2 nicht unterstützt
Wireless: en1: 802.11 a/b/g/n
Video Informationen: ℹ️
Intel HD Graphics 3000 - VRAM: 512 MB
Color LCD 1440 x 900
AMD Radeon HD 6750M - VRAM: 512 MB
System-Software: ℹ️
OS X 10.10 (14A389) - Laufzeit: 0:4:24
Festplatteninformationen: ℹ️
Samsung SSD 840 EVO 500GB disk0 : (500,11 GB)
S.M.A.R.T. Status: Verifiziert
EFI (disk0s1) <nicht sichtbar> : 210 MB
Recovery HD (disk0s3) <nicht sichtbar> [Erholung] : 650 MB
Macintosh HD (disk1) / [Startup] : 498.88 GB (94.91 GB frei)
Core Storage: disk0s2 499.25 GB Online
MATSHITADVD-R   UJ-8A8
USB-Informationen: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Brother MFC-6490CW
Apple Computer, Inc. IR Receiver
Thunderbolt Informationen: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store und verifizierte Entwickler
Kernel-Erweiterungen: ℹ️
/Applications/Kies.app
[nicht geladen] com.devguru.driver.SamsungMTP (1.4.20 - SDK 10.5) Unterstützt
[nicht geladen] com.devguru.driver.SamsungSerial (1.4.20 - SDK 10.6) Unterstützt
/Applications/Magican.app
[nicht geladen] com.magican.iokit.filemon (1 - SDK 10.7) Unterstützt
[nicht geladen] com.magican.iokit.netmon (1 - SDK 10.7) Unterstützt
/Applications/Parallels Desktop.app
[nicht geladen] com.parallels.kext.hypervisor (10.1.0 28600 - SDK 10.7) Unterstützt
[nicht geladen] com.parallels.kext.netbridge (10.1.0 28600 - SDK 10.7) Unterstützt
[nicht geladen] com.parallels.kext.usbconnect (10.1.0 28600 - SDK 10.7) Unterstützt
[nicht geladen] com.parallels.kext.vnic (10.1.0 28600 - SDK 10.7) Unterstützt
/Library/Application Support/Avast/components/fileshield/unsigned
[geladen] com.avast.AvastFileShield (2.1.0 - SDK 10.9) Unterstützt
/Library/Application Support/Avast/components/proxy/unsigned
[geladen] com.avast.PacketForwarder (1.4 - SDK 10.9) Unterstützt
/System/Library/Extensions
[geladen] com.Cycling74.driver.Soundflower (1.6.5 - SDK 10.6) Unterstützt
[geladen] com.delantis.kext.tcpblocknke (2.2.6 - SDK 10.6) Unterstützt
[nicht geladen] com.devguru.driver.SamsungComposite (1.4.20 - SDK 10.6) Unterstützt
[nicht geladen] com.elgato.driver.DontMatchAfaTech (1.1) Unterstützt
[nicht geladen] com.elgato.driver.DontMatchCinergy450 (1.1) Unterstützt
[nicht geladen] com.elgato.driver.DontMatchCinergyXS (1.1) Unterstützt
[nicht geladen] com.elgato.driver.DontMatchEmpia (1.1) Unterstützt
[nicht geladen] com.elgato.driver.DontMatchVoyager (1.1) Unterstützt
/System/Library/Extensions/ssuddrv.kext/Contents/PlugIns
[nicht geladen] com.devguru.driver.SamsungACMControl (1.4.20 - SDK 10.6) Unterstützt
[nicht geladen] com.devguru.driver.SamsungACMData (1.4.20 - SDK 10.6) Unterstützt
Start-Agents: ℹ️
[geladen] com.avast.userinit.plist Unterstützt
[geladen] com.oracle.java.Java-Updater.plist Unterstützt
[ungültig?] com.parallels.mobile.prl_deskctl_agent.launchagent.plist Unterstützt
[ungültig?] com.parallels.mobile.startgui.launchagent.plist Unterstützt
Start-Daemons: ℹ️
[geladen] com.adobe.fpsaud.plist Unterstützt
[ungültig?] com.adobe.SwitchBoard.plist Unterstützt
[geladen] com.avast.init.plist Unterstützt
[geladen] com.avast.uninstall.plist Unterstützt
[geladen] com.avast.update.plist Unterstützt
[ungültig?] com.delantis.tcbblocknke_load_kext.plist Unterstützt
[geladen] com.delantis.TCPBlock.plist Unterstützt
[läuft] com.magican.castle.plist Unterstützt
[geladen] com.microsoft.office.licensing.helper.plist Unterstützt
[geladen] com.oracle.java.Helper-Tool.plist Unterstützt
[geladen] com.oracle.java.JavaUpdateHelper.plist Unterstützt
[ungültig?] com.parallels.mobile.dispatcher.launchdaemon.plist Unterstützt
[gescheitert] com.parallels.mobile.kextloader.launchdaemon.plist Unterstützt
Benutzer Start-Agents: ℹ️
[geladen] com.adobe.AAM.Updater-1.0.plist Unterstützt
[geladen] com.adobe.ARM.[...].plist Unterstützt
[ungültig?] com.avast.home.userinit.plist Unterstützt
[ungültig?] com.delantis.tcpblock.plist Unterstützt
[geladen] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist Unterstützt
Anmeldeobjekte: ℹ️
GrowlHelperApp ProgrammVerdeckt (/Library/PreferencePanes/Growl.prefPane/Contents/Resources/GrowlHelperApp.app)
iTunesHelper Programm (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
EyeTV Helper Programm (/Library/Application Support/EyeTV/EyeTV Helper.app)
KiesAgent ProgrammVerdeckt (/Applications/Kies.app/Contents/MacOS/KiesAgent.app)
fuspredownloader ProgrammVerdeckt (/Users/[redigiert]/Library/Application Support/.FUS/fuspredownloader.app)
Internet Plug-Ins: ℹ️
FlashPlayer-10.6: Version: 15.0.0.152 - SDK 10.6 Unterstützt
EPPEX Plugin: Version: 4.1.0.0 Unterstützt
Flash Player: Version: 15.0.0.152 - SDK 10.6 Mismatch! Adobe empfiehlt 15.0.0.189
AdobePDFViewer: Version: 9.5.5 Unterstützt
Default Browser: Version: 600 - SDK 10.10
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.4.4 - SDK 10.6 Unterstützt
GarminGpsControl: Version: 4.0.4.0 Release - SDK 10.6 Unterstützt
JavaAppletPlugin: Version: Java 7 Update 72 Version prüfen
Internet Plug-Ins des Benutzers: ℹ️
WebEx64: Version: 1.0 - SDK 10.5 Unterstützt
Safari Extensions: ℹ️
OpenIE
wrc
StartPage HTTPS
Ghostery
ClickToFlash
YouTube5
AdBlock
My eBay Manager
Einstellungskarten von Drittanbietern: ℹ️
Flash Player Unterstützt
FUSE for OS X (OSXFUSE) Unterstützt
Growl Unterstützt
Java Unterstützt
MacFUSE Unterstützt
NTFS-3G Unterstützt
Perian Unterstützt
TCPBlock Unterstützt
Time Machine: ℹ️
Überspringen Systemdateien: NEIN
Mobil Sicherungskopie: AUF
Aautomatisches-Sicherungskopie: JA
Sicherungsziele:
\TimeMachine\ [Network]
Gesamt Größe: 2 TB
Gesamtzahl der Sicherungskopie: 27
Älteste Sicherungskopie: 2014-09-19 12:44:24 +0000
Letzten Sicherung: 2014-10-20 13:39:04 +0000
Größe der Sicherungsplatte: Hervorragend
Größe der Sicherungsplatte 2 TB > (Disk Größe 0 B X 3)
Top Prozesse von der CPU: ℹ️
      78% launchd
      23% opendirectoryd
      17% mds
      13% syslogd
      12% notifyd
Top Prozesse vom Speicher: ℹ️
120 MB mds_stores
120 MB com.apple.WebKit.WebContent
120 MB com.avast.daemon
120 MB Mail
86 MB ocspd
Informationen zum virtuellen Speicher: ℹ️
11.67 GB Freier RAM
2.48 GB Aktive RAM
1.42 GB Inaktive RAM
1.60 GB Wired RAM
2.06 GB Seite-ins
0 B Seite-outs

High Speed Digital I/O using 6533

I would like to have a application sending out bit sequence through port0 of PCI 6533 card, and using port2 recieve those bits, then do a pattern matching.
I set the output bit pattern changes at the 10th iteration of my control loop, however, I got the changed bit pattern at lots of iteration later. I cannot figure out what happened.
I want to achieve the pattern matching in the oder of milliseconds(immediately knows the bit pattern has changed). But it seems my programs structure cannot do that. Please take a look at my program and give me some advice, thank a lot.
Best Regrads,
Stee
Attachments:
Testing_6533_buffer.vi ‏143 KB

Hi Stee,
I might have a couple ideas why your data might be delayed. But help me understand what you are trying to accomplish. Are you trying to acquire continuous data from port 2? Are you acquiring it using change detection (you want to acquire everytime there is a difference in the data)? Do you want to acquire it with a pattern match trigger?
What I imagine is happening is that you are only acquiring data every so often and the PCI-6533 card by default is transferring this data via DMA. The interesting thing about this is that if you need each sample right away transferred to the PC Memory so you can read it, it might not happen with DMA. This is because in DMA mode on the PCI-6533 the "MITE" chip that packs data for transport waits until it h
as enough samples to send. Therefore, if you are only acquiring so often, you might be trying to read the present data (which is on the board) but the MITE is waiting to pack the data and send it to the PC Memory so you can read it.
What you need to do in this case is use the Set DAQ Device Info.vi to change the transfer mode from DMA to interrupts for the second group (your digital input). In interrupt mode, as soon as you input data, it is sent via interrupts to PC Memory. This means it won't wait for a "packet" to be filled before it sends the data. This means if you are acquiring digital input at rates up to 500kHz, interrupts will allow you to get the data right away.
Anyway, let me know if I wasn't clear in my explanation. Hope that helps.
Ron
Applications Engineer
National Instruments

I need a one-lens solution for my photo needs on high speed Corvette Races. Will 35-350L do?

I need one lens to carry on my 1D during long road rallies with the Corvette Race club. Would the 35-350L be a good canditate?
Solved!
Go to Solution.

You have a 1D ? Or do you have a later 1 D seires camera?
I have used and still use a 1D. It would not be my first choice, or 2nd, or 3rd, for motorsports shooting with whatever lens.
At 4MP you are going to be really handicaped in any sort of enlargements.
The 1D is a fantastic camera and at one time the best camera in the world with a, at the time, insane price of around 8 grand.
If you do indeed have a 1D, I would search for a later 1 series and the best buy right now is a 1D Mk III.
Than the addition of the EF 35-350mm f3.5-5.6, or better yet the EF 28-350mm f3.5-5.6 should work well.
With a lot of practice as suggested above.
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 8.7, Lightroom 5.7

High speed digital data display.

I am using Labview 6.0 on Win2K. I want to develop an application that can display real-time video data at rates upto 24MB/sec. Can Labview cope with this amount of data?

Byr,
It all depends on what you intend to do with the data and whether you actually have a source that will bring data into LV at such a rate, but for the acutuall display protion 24MB/Sec should be cake.
Regards,
Amaury Rolin
NI Applications Engineer

Do I Need High Speed HDMI for 1080p

My Appletv works great and I am so happy with HBOGO but I don't think I am getting 1080p or even 720 while watching. I have an HDMI cable from the ATV to my AV receiver but it is a plain hdmi vs a high speed hdmi. I do have a high speed cable running from the av receiver to my tv. So do I need a high speed hdmi from Apple TV to my av receiver to get full HDTV quality?

no any hdmi v 1.3 cable will work
even though there are people who are more then happy to charge you 100's for special magic super cables

How to write to DAQCard-5633 Port at high speed

I am looking for a sample vi that allows me to write a 8 bit x n digital array out at high speeds with a DAQCard-5633 high speed digital I/O card. I realize I need to use the traditional DIO vis, specifically the DIO Write.vi, but haven't been able to make it work yet. I tried the sample vi I found on-line called syncDIO_32HS.vi, but that doesn't write anything out, and gives a timeout error. I know the card works because I can do low speed DC write type operations.

I found the solution myself. If I am using I/O connector handshaking I need to connect REQ and ACK. I should have used internal handshaking.

No high-speed USB ports?

When my I-Pod Shuffle is plugged into either of the two USB ports in the back of my computer's modem, my computer states that there is a "High Speed USB Device attached to a non high-speed hub" and that "There are no high-speed USB host controllers installed on this computer". So I take it I'm going to have to buy some sort of high-speed USB device to fit the I-Pod, but I have no earthly idea where I would buy one!

No - you dont need a high speed port it will work fine with a 1.1 (low speed) port. It will just take a lot longer to load songs on your shuffle.
As long as it charges (high powered port is needed - you can have high powered port which is low speed) you shoud be OK.
If you dont like the transfer speed you can probably take out the USB card that you have and replace it with a 2.0 card - a fairly easy and relatively cheap procedure, but if you dont feel comforatble doing it ask a freind who is a bit more tech savvy.

I need to count intermittent high speed pulses from an outside source with cFP-CTR-502 and labview.

I need to count intermittent high speed pulses from an outside source with cFP-CTR-502 and Labview 8.2 . I've found example code for generating pulses and creating intricate count setups but no straightforward examples of a simple counter. Any suggestions?

Hello tinfish,
I could not find a simple example that implements simple counting either, but it should be straightforward enough for us to try. Do you have the CTR module configured properly in MAX? If so, can you monitor the channels on your CTR 502 for input? Try connecting a square wave or some other digital pulse to the terminal to test the functionality of the counter module first (before programming). If you monitor the input channels with somethign connected you should see the count increment each time it sees a rising edge (assuming default configuration).
Once you've verified that everything works in MAX, you can set up your CTR module in a LV 8.2 project. If you need help with this, refer to the help document (look in the "Configuring FieldPoint in LabVIEW" section):
C:\Program Files\National Instruments\FieldPoint\documentation\Online Help\fplv.chm
You should be able to just read a channel tag from your CTR 502 using an FP Read VI. (Simply drag the channel from your project onto the block diagram). Since counting is the default behavior of the 502, there is no special programming involved to make it work.
I hope this helps -- if it's too high-level we can talk details about specific questions you have. Have a good one!
Charlie S.
Visit ni.com/gettingstarted for step-by-step help in setting up your system

HT201295 Late 2009 Intel iMac Needs Frequent SMC reset - constant high speed running fan

Late 2009 Intel iMac is having reoccurring episodes of high speed fan running, especially after waking it up. The SMC reset by unplug and reboot works, but I worry that this is a serious sign and that the machine is slowly dying. Any thoughts? Works fine otherwise.

wolfgang272 wrote:
Do you have any ideas?
Yes, you just need to reset the SMC and you should be fine
https://support.apple.com/kb/HT3964
Whoops you already did that.
Hardware Test then
https://support.apple.com/kb/ht1509
Read more info here
https://discussions.apple.com/message/16276201#16276201

Is high speed needed

Is high speed internet needed for the airport extreme to work? I want it for the other functions and only have a slow dial-up connection. Can it function fully with having an internet connection?

The AirPort Extreme base station (AEBS) can be used without any connection to the internet.
The AEBS does NOT have a built-in modem of any kind and therefore it will not be able to directly connect to any dial-up ISP.

Digital start trigger and high speed camera

Is there any particular option or way available in LabVIEW to initiate the data acquisition and high speed camera using a digital start trigger? If yes, shall I create a task for high speed camera and then synchronize it with the other tasks?
Kind Regards,

Hi Helen19411,
The way to trigger data acquisition in LabVIEW is to use the 'DAQmx Start Trigger VI'. To set this up I recommend taking a look at this example:
http://www.ni.com/example/25282/en/
Without any information about the high speed camera you are using, I can't give much advice. If the device is viewable in MAX then you may be able to create a task, and so long as you synchronise both channels in your code, the digital trigger should activate both events.
Kind Regards,
TomS
Applications Engineer
National Instruments

I changed from a dial up to a high speed network and can no longer get Firefox to work as my browser. What do I need to do?

I changed from a dial up to a high speed network and can no longer get Firefox to work as my browser. What can I do.
I did try to download Firefox again, but still will not work.

Download a fresh Firefox copy and save the file to the desktop.
* Firefox 6.0.x: http://www.mozilla.com/en-US/firefox/all.html
* Uninstall your current Firefox version.
* Do not remove personal data when you uninstall the current version.
Remove the Firefox program folder before installing that newly downloaded copy of the Firefox installer.
* It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
Your bookmarks and other profile data are stored elsewhere in the Firefox Profile Folder and won't be affected by a reinstall, but make sure that you do not select to remove personal data if you uninstall Firefox.
* http://kb.mozillazine.org/Profile_folder_-_Firefox
* http://kb.mozillazine.org/Profile_backup

I need a high speed digital I/O solution!

Similar Messages

Maybe you are looking for