I need a user manual for a PCI-MIO-16E-1 DAQ card
I am starting research using a PCI-MIO-16E-1 DAQ card that was used by a prior student and the manual is not available. I tried to access the manual online through your websitem, but I was denied access. How can I gain access to this manual so I can start to use this DAQ in my research?
What you need is the E Series help file. Here is the link, but for some reason if you can't get there, the zip file is attached.
-Alan A.
Attachments:
370503f.zip 1260 KB
Similar Messages
-
Buffer of PCI-MIO-16E-1 acquisition card
I am using a PCI-MIO-16E-1 acquisition card, and in the manual it says that it has a FIFO buffer of 512 samples. Is this the total buffer of my card? (I guess it should be larger). If I take more samples than can fit in the buffer in a single acquisition, what happens to the extra samples acquired? Are they stored in the computer memory?
Thank youThe PCI-MIO-16E-1 actually has a FIFO buffer size of 2048 samples. The hardware buffer size is not a limitation of how many samples you can read at a time. FIFOs are often used on DAQ devices to temporarily store incoming or outgoing data until that data can be read or written. For example, an analog input FIFO stores the results of A/D conversions until the data can be read into system memory.
So, the FIFO on the device will just hold the data temporarily until the computer can transfer the data to computer memory. FYI: When you programmatically set the buffer size in your application, you are setting the software buffer size in computer memory and that has nothing to do with the FIFO size. You don't have to worry about the FIFO within your program. I hope th
is helps.
Regards,
Todd D.
Applications Engineer
National Instruments -
I need a User Manual for my SONY turntable: PS-LX340. Does anyone have one?
Is there a place where I can see or download the User Manual for my SONY turntable: PS-LX340?
The PS-LX340 turntable was first released in the market last 6/1/1985. We no longer have the user manual available at our Parts and Accessories website. You may check about the manual's availability (part number 376054421) with our Sony Authorized Part distributors listed below:
Andrews Electronics Inc.
661-257-7700
www.andrewselectronics.com
Encompass Parts Distribution
800-638-3328
www.encompassparts.com
Fox International
440-725-7150
www.fox-international.com
If my post answers your question, please mark it as "Accept as Solution" -
Pulse Train Generation using PCI-MIO-16E-4
I need to generate pulse trains of changing pulse widths using PCI-MIO-16E-4 daq card using Igor Pro.
I have tried to use the CTR functions (but always keep getting errors and it doesn't work). I also used the general purpose counters (GPCTR functions) but cannot visualise them on a CRO. If someone can help in regards to the programming aspect, it will be greatly appreciated.
Thanks
VakulHi Vakul,
Some questions that might help me to get you a solution.
Are you using Traditional DAQ, or DAQmx and which versions are you using?
What operating system are you running?
When you say you can't visualize them on CRO, I assume that you are hooking the counter out to a cathode ray oscilloscope and can't see the pulse train?
Are you going to need more than two different pulse widths for your pulse train?
There are several online knowledge bases describing how to change the frequency of a pulse train on the fly.
This link explains how to use software to create a new pulse width.
http://digital.ni.com/public.nsf/websearch/7B1B0427C39FE33086256CEE00752133?OpenDocument
This link discusses using frequency shift keying, which will only allow you to have 2 different pulse widths.
http://digital.ni.com/public.nsf/websearch/EC1F089252F33B248625696E006FB6FC?OpenDocument
I assume that you are writing this program to compile in Igor Pro using C. I can help you with the C code development, but don't know anything about the Igor Pro API.
Please get back to me about those questions and let me know if you need further help.
Michael Denton -
Need User Manual for CT-4870 C
Anyplace I can get a user manual for a Sound Blaster CT-4870 Sound Card?
Link will do if that is all there is. I tried the knowledge base at this web site and just kept going in circles.
I'm specifically interested in the in/out sockets. I figured out the mic and speaker ones but there are others that I need to understand whether they are line in, or line outs and if they are standard /2 mini plugs (3 ckt) or those fancy multi-pole type things.
DMKUnless you can find something on HP's site (the CT4870 is listed as a HP OEM card, Sound Blaster Li've! Value HP / NEC - CT4870), this is about the closest you're going to find,
http://us.creative.com/support/downloads/download.asp?bEOSLAgree=yes&action=next&OS=0®io n=&Product_Name=Li've!&Product_ID=4857&driverlang= 033&drivertype=2&MainCategory= -
Need user manual for NI DAQPad-6016
Need a user manual for the NI DAQPad-6016. When I download the E_Series_Help.chm file off the NI website and run it, I get the following message:
Action canceled
Internet Explorer was unable to link to the Web page you requested. The page might be temporarily unavailable.
andy-lLaura:
Thanks for the info!
I have submitted feedback a couple of times to the effect that I prefer PDF documentation.
I was not aware of the uncompiled help files. Are these generally available any time the compile help file is used? They are helpful in that I can view them on my Macintosh. I still prefer the more book-like PDF format, though.
I am downloading chmMagic to give it a try.
Thanks for the help! There's so much stuff on NI's web site it can be hard to know what's available and how to find it.
John Weeks
WaveMetrics, Inc.
Phone (503) 620-3001
Fax (503) 620-6754
www.wavemetrics.com -
Inputing TTL pulses to NI-PCI-MIO​-16E-1 via BNC-2110
I need to count TTL pulses coming from photomultiplying tube (PMT) module. Can someone tell me, please, how do I connect BNC cable from PMT module to NI PCI-MIO 16E-1 DAQ board via BNC-2110 adapter?
thanks a lot in advanceHello Photon Guy,
Thank you for contacting National Instruments.
I have attached an image which shows how to connect the USER 1 BNC and USER 2 BNC connectors to the proper PFI pins which serve as the source of counter 0 and counter 1. You should only need to use one counter to count edges.
Regards,
Bill B
Applications Engineer
National Instruments
Attachments:
BNC-2110.JPG 105 KB -
Pins at a PCI MIO-16E-1 to Measure Frequency(DAQ-STC).vi?
I want to measure frequency with the
"Measure Frequency(DAQ-STC).vi".
Can't find the appropriate connector pins
in the manual of my PCI MIO-16E-1.
Can someone confirm or correct me?
Signal - PFI1/GPCTR1_SOURCE
SignalGND - PFI9/GPCTR0_GATE
PFI8/GPCTR0_SOURCE - PFI4/GPCTR1_GATE
Thanks in advance
ManfredManfred,
You can find this information by going to the http://www.ni.com/manuals site and viewing the E-series manual. There is a table which shows the pin number, name, and function for each pin.
Pin 10 - PFI1/Trig2
Pin 11 - PFI0/Trig1
Pin 43 - PFI2/Convert
Pin 42 - PFI3/GPCTR1_Source
Pin 41 - PFI4/GPCTR1_Gate
Pin 40 - GPCTR1_out
Pin 6 - PFI5/Update
Pin 5 - PFI6/WFTRIG
Pin 3 - PFI9/GPCTR0_Gate
Pin 2 - GPCTR0_Out
Pin 4,39,35,36 - DGND
Mark -
Possible sampling rates of a PCI-MIO-16E-1 with DASYLab
Hello!
I'm using a PCI-MIO-16E-1 DAQ. It's maximum sample rate is 1.25MS/s
My questions:
- What does maximum output rate of 1MS/s mean? I need 3 channels at 400kS/s.
- What are the possible sample rates? Can I use e.g. 3 channels with 105 kS/s each?
- If not what are the fixed sample rates of that card?
Thanks a lotHi matadler,
The E-Series boards have one DAC for each output, therefore you can use the full output rate with all output channels.
The PCI-6070 (formerly known as PCI-MIO-16E-1) has 2 analog outputs, which can be used at up to 1 MS/s. If you need more analog outputs, you need another board.
Analog inputs on the E-Series boards are multiplexed. This means you have only one ADC which is used for all analog input channels. You have to divide the maximum sampling rate by the number of channels you actually use.
For your application, this means you can use up to 416kS/s with 3 channels. There are no fixed sample rates on the board, so it's no problem to use 105kS/S.
Regards,
Richard H.
National Instruments -
Automatic Conversion of PR to PO.. Need User Manual for ME59 T code
Hai Sap Gurus,
I Got the following content from net. but kindly help me by sending me user manual for ME59.
You created purchase requisition for various material. During creation of purchase order you used the following path:
Purchase Requisition
.......Follow on function
.........Create Purchase Order
............automatic via purReq.
When you mentioned required purchase requisition number and execute, system give error that purchase requisition does not contain any suitable item.
Is there any setting in customization where you can monitor and use that function.
In an effort for you to successfully use the Transaction Code ME59 to automatically convert the current PR into PO, then the following criteria should be met:
1) In the Purchasing View of the material master data, the "Autom. PO" field must be clicked;
2) In the Purchasing View of the Vendor Master Data, the "Automatic Purchase Order" field must be clicked;
3) The Outline Agreement or Purchasing Info Record shall be maintained which will allow the automatic copying of unit price and other conditions into PO;
4) The Source List shall be maintained for the nominated vendor which was shown in either the Outline Agreement or Purchasing Info Record.
or
it might be PR subject to release strategy and not yet released
or
If you're not using a source list or automatic creation of PO, you may need to assign the requisition to a purchase information record using transaction ME56. Then it should appear in ME58
Thanks.. Reply me pls...
Edited by: Swetha SAP Girl on Jun 18, 2009 2:19 PMHi,
Step by step process for automatic PO creation from PR
1. Tick check box in purchasing view of Material Master(MM01/MM02)
2. Tick check box for auto PO in purchaisng data of Vendor Master record (MK02)
3. Maintain Source list for Material,plant and Vendor combination in ME01
4. In ME51N create PR and assign source of supply in "Source of supply" tab
5. In ME59N key in Purchaisng Org., Vendor and Plant - execute
You will get POs created with reference to PR automatically.
Hope its clear
Regards,
Uzair Hussain -
Need User Manual for Firefox.
Hi hiddensmiles,
We have a whole section here on [https://support.mozilla.org/en-US/kb/how-do-i-install-firefox-and-get-started Getting Started with Firefox]. It should cover all the basics from downloading and install to using the core features.
If you have other questions, be sure to search the Knowledge Base. There is tons of great information there. If you can't find your answer there, you can always ask the volunteers here on the forums.
Hopefully this helps! -
In need of a user manual for s660W
Hi,
I just bought a Lenovo mobile phone model s660w. It came with no instructions manual and I have been looking online for one. When looking through Lenovo web site all I could find was s660 which has one sim card slot and not two and probably several more differences...
Can anyone tell me why and where I can find a user manual for my phone?
Thank you,
Chen
Solved!
Go to Solution.Hi Chen
Unfortunatly Lenovo dosen't make a S660W model.It's fake!
http://forums.lenovo.com/t5/A-and-P-Series/IMPORTANT-List-of-fake-replica-Lenovo-phones/td-p/1736253
I know this isn't the answer you were hopping for but if you ''just bought it'' I suggest contacting the seller for a refund.
Regards.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as ''ACCEPT AS SOLUTION"!
Unsolicited PM's will not be answered! ....Please post your question/s in the appropriate forum board.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество -
Need User Manual for Bex Analyser BI 7
Hi All
We have to prepare the user manual for Bex Analyser to show all the functions. If anyone has any link kindly let me know.
Thanks for your help
Regards
SathyaHI ,
See this link
http://help.sap.com/saphelp_nw70/helpdata/EN/ba/45583ca544eb51e10000000a114084/content.htm -
Need user manual for VXI pc850 controller
I need this user manual - does anyone have a pdf they could send me?
I am trying to replace this obsolete controller with a VXI pc872b controller - has anyone done this and what problems were encountered?Rob hope this helps:
http://digital.ni.com/manuals.nsf/websearch/E6B29F1F945A48988625665F006A616B?OpenDocument&node=132100_US
Kind Regards
Steven Bird -
User manual for Toshiba notebook needed
who can give me user manual for Toschiba notebook
7010 CT /4,3 Model No PAP 701 E A serial # 8026089
Or can indicate wgere I can find it
Thanks have a great day
Rudolph
Message was edited by: rudolphHi
I guess I can answer Your question! Follow this link and
eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_manuals.jsp
Please note that the link is the complete text between the < and >
BR
Tom
Maybe you are looking for
-
Can't delete file from my public drop box
Files were copied to my own drop box folder at ~/public/drop box/ and when I want to delete them it says it is locked. I can't unlock because I don't have permission. If I look at the permissions I see "fetching: custom, fetching: read and write, eve
-
Installing OSX on 24" iMac with broken Display
Hi, I have a 24" iMac but the Screen is broken. It still worked with a external Display connected via MiniDVI but now i would like to install OSX 10.6. The problem is that I can't get the Installation to show on the external Display and I can't see w
-
So I have the new bbm but half of my contacts say that they can't see my display name or picture. Does anyone know how I can fix this? Thanks!
-
Hi! I'm making a website in flash, inspired from this site : http://www.heyerdahlhandel.no I've done mouseover so that when you go over a circle you can see full text in the middle, but I don't know how to make the other "buttons"/circles fade white
-
An unknown error occurred (-3212).
The last iTunes update created an error message when I went to access the iTunes Store. Does anyone know how to fix this? I am connected to the internet without an issue.