I need an equipment with an entry USB port to send a wav file and exit I & Q

We are working with an equipment consisted in a transmitter and a receiver.At the end we have 2 computers,we are trying to send a wav file through USB port from one computer and converted to I & Q signal (that supports our transmitter).
On the other end we have to convert from I & Q signals to a signal who can interprete the USB port.
Our ask is if exists an equipment which could do these two fuctions.
Thanks a lot.
Attachments:
national.doc ‏34 KB

We have data acquisition (DAQ) devices that have a USB interface. You could send a .wav file to an analog output of a USB-DAQ device and you could acquire an analog signal (with analog inputs on a USB-DAQ device) and write that to a .wav file with another USB-DAQ device.
What is an I&Q signal? You need to give more information on what what characteristics are needed for a signal to be I&Q. I have included a link below to a USB-DAQ device within our on-line catalog for you to take a look at.
NI DAQPad-6020E for USB
http://sine.ni.com/apps/we/nioc.vp?lang=&cid=11922
Regards,
Todd D.
Applications Engineer
National Instruments

Similar Messages

  • To add a 6 TB G-Raid (Mac os extended) ext drive to a 2Tb time capsule, using a powered usb with the TC usb port. Using the airport utility 5.6 on iMAC (10.7.3). Went to manual setup,then disk. Have options of the TC

    Want to add a 6 TB G-Raid (Mac os extended) ext drive to a 2Tb time capsule, using a powered usb with the TC usb port. Using the airport utility 5.6 on iMAC (10.7.3). Went to manual setup,then disk. Have options of the TC or 6TB. Won't allow update to the 6TB

    4Buck5 wrote:
    Want to add a 6 TB G-Raid (Mac os extended) ext drive to a 2Tb time capsule, using a powered usb with the TC usb port. Using the airport utility 5.6 on iMAC (10.7.3). Went to manual setup,then disk. Have options of the TC or 6TB. Won't allow update to the 6TB
    I am not 100% what isn't allowed.. but I am assuming you want to spread the backup across the two disks.. internal TC and 6TB external.. this is not possible.. It has to be one or the other. TC has no way to build a raid JBOD or anything else. Nor would you want to as that is the most likely to fail and kill your data.
    Let me add, backing up 6TB over USB on TC.. will be the most excruciating experience of your life.. cf child birth or passing kidney stones.. large ones.. being the male equivalent.

  • HT1386 Why when I select not to update the calendar with any entry older than 1 day it ignors that and goes back as far as my calendar has entries

    Why when I select not to update the calendar with any entry older than 1 day it ignors that and goes back as far as my calendar has entries

    FCPx answer: At least the answer that worked for me...
    I had the same problem, as I believe many others had.
    In my case the problem was with one of OSX Mavericks' new features: APP NAP.
    It looks like this is ON by DEFAULT for ALL Applications and that FCPx, or Compressor for that matter, will not work if this is enabled on them.
    I just disabled App Napp on FCPx and now it works, again, like a charm.
    This is how you disable App Nap: http://reviews.cnet.com/8301-13727_7-57612009-263/how-to-disable-app-nap-in-os-x -mavericks/
    I hope this helps,
    Mariano

  • I added icloud to my ipad 2 what will i need to do with my mac in order to start seeing the video and pictures on my  mac onceI take them on my ipad

    I added icloud to my ipad 2 what will I need to do with my mac in order to start seeing the video and pictures on my  mac once I take them on my ipad ?

    See Here
    Apple - iCloud - Learn how to set up iCloud on all your devices.

  • I have had IPhones since their inception.  Last phone was the 5.  A few months ago, I upgraded to the 6 Plus. Here is my issue. On my 5, my car radio (which has USB port) allowed me to plug in and listen to radio or music from my phone and the bonus

    I have had IPhones since their inception.  Last phone was the 5.  A few months ago, I upgraded to the 6 Plus.
    Here is my issue.
    On my 5, my car radio (which has USB port) allowed me to plug in and listen to radio or music from my phone and the bonus was it charged the phone as well. All worked great.
    Now with the 6 Plus, neither of things work.  The message on the radio (Kenwood) says I Pod error.  The message on my phone say's "this device is supported".
    I have called on this before and was told you are aware and that the issue will be addressed in a future update.  There have been several updates on IOS 8 and the issue remains.

    I have a Kenwood KDC-X695. When I purchased this stereo and had it installed, I had an ATT iPhone 4.
    It worked with the stereo, but had a few issues. I had purchased a few audio books that I would listen to while driving. When I plugged it in it would immediately begin to play the book from the beginning or if I had been listening to music, it would start playing the song that was at the top of the song list.
    The stereo came equipped with Firmware version 3.05. I upgraded to the iPhone 5 a year later. I had that phone for approximately 2 years. The song or book issue remained the same.
    I just recently upgraded to the iPhone 6 and the Bluetooth function still works, however the USB port on the stereo that the phone plugs into to allow files on the phone to play through the stereo no longer works.
    I contacted the service provider (Verizon) and after speaking to several different technical support technicians, they provided me the phone numbers for Kenwood and Apple because they were unable to help me.
    I spoke with Kenwood technical support the following day and after a few fumbling miscues from the technical advisor, it was suggested that I upgrade the firmware, even though the Kenwood literature warns against this if the Bluetooth portion is working, because if there is a problem with the upgrade, it can render the Bluetooth useless and non-functional. The advisor did suggest the latest firmware on the second or third attempt, after I pointed out what I was able to glean from my initial search.
    Later that day, I went back to the Kenwood site (from their homepage) and by using their selection tools, discovered that this particular model was only ever intended to be used with the iPhone 4S (the technical advisor was not aware of this, even though I mentioned this during my phone call earlier in the day). According to the Firmware selection tool, my iPhone 5 should not have worked with it.
    I performed the Firmware upgrade, and it took 13 minutes. This was less than the 15 minutes that was forecast in the Kenwood literature. The Bluetooth still works but the USB cable connection still causes the unsupported device message that I received prior to the upgrade. I am incredibly annoyed and disappointed.
    By upgrading to the iPhone 6, I have three choices; (1) only use the Bluetooth for phone calls without the ability to play other files from my iPhone 6 (2) forced obsolescence of my stereo, requires buying a new stereo (3) return my iPhone 6 and go back to my iPhone 5.
    I do not believe that I should have to be a software/Firmware/hardware engineer, vetting every single device that I own; prior to upgrading a cell phone.
    I am incredibly annoyed with Apple at the moment.
    I have a separate Bluetooth headset that worked with both my iPhone 4 and iPhone 5 that the iPhone 6 simply does not recognize. That is another story for another time.
    Currently, I am incredibly underwhelmed with Apple.

  • On Apple TV. Can the USB port be used for a keyboard and mouse interface

    On Apple TV. Can the USB port be used for a keyboard and mouse interface

    A bluetooth keyboard can be used with the Apple TV.
    There is no need for a mouse with an ATV.

  • Hello i need a help about script to export translatable text strings from ai files and import them back

    Hello i need a help about script to export translatable text strings from ai files and import them back after editing, thanks in advance

    Lanny -
    Thank you for taking the time to help with this problem. Can I just say however that as someone who has posted a first comment here and quite clearly never used a forum like this before, your comment unfortunately comes across as very excluding. It makes me feel there are a set of unwritten rules that I should know, and that I don't know them shows that the forum is not for me. In short, it's exactly the kind of response that stops people like me using forums like this.
    I'm sure it's not intended to be received like this and I am sure that the way you have responded is quite normal in the rules of a forum like this. However, it is not normal for those of us who aren't familiar with forums and who only encounter them when they have a genuine problem. This is why I hope it is helpful to respond in full.
    The reason I posted here is as follows. I was directed here by the apple support website. The original comment seemed to be the only one I could find which referred to my issue. As there is no obvious guidance on how to post on a forum like this it seemed perfectly reasonable to try and join in a conversation which might solve more than one problem at once.
    Bee's reply however is both helpful and warm. This could in fact be a template for how new members should be welcomed and inducted into the rules of the forum in a friendly and inclusive way. Thank you very much indeed Bee!

  • After downloading ISO8 my USB Ports on my IMAC arnt working and now my iPad2 will not charge?

    after downloading ISO8 my USB Ports on my IMAC arnt working and now my iPad2 will not charge? even tried to use 240v charger? both my iMac and iPad have been updated, my mini iPad is working on old iso7 so that won't be updated in a hurry, any help would be great.

    First is the most USB ports do not provide enough power to charge an iPad. Do not try and charge your iPad from such USB ports.
    There is no 240v charger. There is one charger that will work with US voltages and European voltages. If your iPad is not charger with the charger, make certain that is an iPad charger, not an iPhone charger. If the charger does not work try swapping the cable as the cable may be bad. If that does not work try another charger. All simple steps that should be attempted before pinning the problem on IOS 8.

  • Having trouble with wav files and sample rates

    Hi ,I am having trouble with wav files and sample rates .I have been sent multiple projects on wav as the main instrumental ; I wish to record in 48.000kHz .Now comes the problem.When I try to change the project to 48k It seems to pitch up the track.I can't have them send the logic/project file as most have outboard synths,different plug ins etc.This particular case the producer has recorded the synth task in 41.000 kHz .My successful outcome would be to be able t create a project file in 48 kHz .And NOT pitch up whne I add the instrumenta wav file .Any help would be gratefully recieved,this is my first post so any mistakes I may have made go easy 

    You'll have to convert the actual synth audio file file that the producer gave you to 48kHz. You can do this in the audio Bin in Logic.

  • IPhone 6 won't play with Kenwood stereo USB port. Help !!

    I have a Kenwood KDC-BT743U Stereo in my car, which has a front panel USB port.  I've been able to connect my iPhone 4S and play music from my iTunes catalog as well as stream music from Pandora, Soundcloud, Tune In Radio, Mixcloud et al, without any problems until yesterday.....
    Now that I've upgraded my phone to a iPhone 6 and when I connect it to the stereo via the USB port, it doesnt play at all.  After about 2 minutes of trying to connect , I recieve a 'USB Error" .   As I stated, I've had no problems with my iPhone 4S, which I've used with this same stereo deck for the last two years without any problem what so ever.
    I'm looking for some guidance on next steps to take in order to fix the problem? Did Apple change the spec in some sort of way?  Do I need to go to Kenwood for a firmware update (their website provides no information about iPhone 6 compatability with any of their stereo's which is very odd to me) ?
    Please help, my life in the car during long commutes is just not the same......

    Possible Solution:
    1. Go to Settings > General 
    2. Go to Restrictions
    3. Enter Passcode (possibly x2)
    4. Enable Restrictions
    5 Disallow CarPlay
    6. Reset Network Settings (Not 100% sure if this step is needed)
    7. Have at least 1 song in Apple Music App
    8. Have Iphone at Home Screen
    9. Connect Apple Original Cable
    10. That 1 Song should start playing
    11. Open Prefered Streaming App and hit Play
    Carplay negatively affects USB connection with Non-Carplay USB Audio Receivers.  
    I have the Iphone 6 with 8.3 iOS connected to Pioneer avh-41000dvd car stereo and the above solution fixed USB audio issues, including Error code 22-65.
    If you are having issues upon reconnect, disconnect and bring Iphone to home screen and reconnect. 

  • IPod touch won't work with car's USB port after sw update

    I've been using my iPod with my 2011 Honda CR-V's USB port to play my music through the car's audio system without issue since I bought the car.  This stopped working after the latest iPod software update a few days ago--the msg on the audio screen says it's now "unsupported". Is there anything I can do to fix this without a full restore? Why did it change?  Thanks for any help.

    Hey there,
    Glad to hear we're getting closer. Looks like you're connected to the network, just not able to utilize it's internet connection.
    Let's check your iPod's IP addres. Tap Settings > Wi Fi and look for your network. To the right, there's a blue circle with a white arrow in it. Tap that circle. If the IP address starts out with 169.x.x.x, it is a self-assigned IP address. Since it came from the iPod, and not the router, it can't be used.
    I would recommend resetting your iPod's network settings:
    Settings > General > Reset > Reset Network Settings
    When the iPod restarts, reconnect it to your network and try Safari again.
    If it still isn't working, try powercycling your router and resetting those settings at the same time.
    1. Turn off the router
    2. Reset the network settings again, as indicated above
    3. Turn the router back on
    4. Reconnect the iPod to the network
    If it still isn't working, let's check your iPod's software version.
    Settings > General > About
    If you've upgraded to 2.0, the latest version is 2.0.2. If you haven't upgraded, the latest version is 1.1.5. If you're not at either of those numbers, connect the iPod to your computer and use iTunes to check for software updates for the iPod.
    Regarding the router settings, I'm not familiar with your router manufacturer. I'd check their website for instructions on that. I think at this point you wouldn't really need to change any settings, but just check for firmware updates.
    CG

  • Is it possible to perform a backup with a broken USB port? (Q10)

    Hi there! The USB port of my Q10 does not work. (I bought it like this, knowing of the defect.) I thought it's a hardware/contact problem, but it's not: I disassembled the Q10 and tested if the contacts of the USB port are connected correctly to the PCB by measuring. (Yes, I'm an electrical engineer.) The device does not charge and it's impossible to establish a USB connection to a computer. It's also not a software issue: I factory reset the phone two times before using it. I want to buy a new Q10 and transfer all data from the old to the new phone. I thought of doing a full backup with Blackberry Link. For Blackberry Link to work I need either a USB connection or a Wifi connection. The latter only works when the Q10 is connected to a charger. You see the problem?  So my questions are:- Is it possible to transfer all of the data from one phone to another without using USB? Wifi, Bluetooth, whatever?- Is it possible to do a full backup of the phone without Blackberry link?- If not, are there any apps that I can use that backup most part of my data? BTW: Blackberry blend works, but there I can't backup local calendar and other data this way, only photos and videos. Thanks for your help! 

    Hello,
    Via Media Card, one option is a 3rd party backup app called Ultimate Backup.
    For the native LINK method, my memory tells me that BT integration was not included, so that won't work. I don't know if any 3rd party tools can work that way or not.
    Good luck!

  • Trouble with all 3 USB Ports: HP Pavilion 14-v062us Notebook PC

    I was recently playing a game on my computer with a mouse controlled by a USB drive.  A little bit into the game, the mouse disconnected for no known reason.  I have been playing this game about six months now, and have never had this problem in the past.  I relocated the drive to the other two ports, but the device was not recognized in any of the ports. I plugged in another device controlled by a USB drive and got the same results.  I have uninstalled the USB Composite Device and USB Root Hubs then restarted my computer to no success.  Any help towards identifying and solving the problem is greatly appreciated!

    Hi there @D3rr1ck,
    Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
    I understand that you are having problems with all of the USB ports on your notebook. I am happy to help with this.
    Take a look through the following and try the sections that are applicable.
    HP PCs - Troubleshooting USB connections (Windows 8)
    Normally the USB driver is a part of the chipset drivers for a board, so you can also try updating that, which you can find on this page: HP Pavilion 14-v062us Notebook PC (ENERGY STAR) - Software and Drivers
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • ITunes Library set up on NetGear R6100 router with ReadyShare from USB port?

    Can the iTunes Library be set up on a NetGear R6100 router with it's NetGear ReadyShare feature. from a USB thumb drive or USB hard drive attached to the one available R6100 router's USB 2.0 port?
    I have read the Apple forum post about a similar question for the more advanced NetGear R7000 router, which says it can work there.  Unlike some of the other sibling Netgear routers that do not have ReadyShare, my R6100 does, which leads me to believe that it should work, since its the same technology (they both have a router USB port with ReadyShare). It just appears that the documentation is very limited. The other post said to format the USB drive to the Apple format (HFS+), rather than Fat32, get the Mac or Apple to see the iTunes directory located on the router's USB port.
        I'd like to know if anyone has had any luck using the ReadyShare.feature on their R6100 for sharing their iTunes library to the same iTunes account on different devices (laptop, PC, AppleTV, iPod, etc).  My Apple TV has recently acquired a problem of not being able to detect the iTunes library on my PC, aftert a recent iTunes update, but that's another problem that the forums show a lot of people having.  So I figured that since my R6100 router has the ability to share media over the network, I would try to move my iTunes library there, hopefully to make it easier to access by my Apple TV, and make it unnecessary to have my PC running when I watch my purchased iTunes movies, that are stored in that library.  Interestingly, my movie and TV show files are stored in my iTunes Music folder under the "Movies" and "TV Shows" subdirectories (folders). The way it is set up now, if I'm watching a HD movie purchased from iTunes with my Apple TV, the movie stops playing as soon as my PC is shut down, which confirms to me that the large movie files are being pulled from there to my Apple TV. 

    Oh groan, not another conspiracy theory.  No, it's a lot more likely Apple and Netgear and the dozens of other manufacturers haven't gotten together with the thousands users who have come up with hundreds of thousands of ways of rigging things up and tested each and every one of them.  I am confident if Apple were out to mess things up for you they could have come up with something a lot more devious.
    Did you do a web search for this?  With a Google search specifying Netgear with this error I found:
    ReadySHARE USB Hard drive access issue from a Mac Computer (Time Machine or iTunes not working properly)
    - Able to see USB hard drive content but unable to write to USB hard drive connected to router's Readyshare port from Mac computer.
    - Error that says  "The iTunes application could not be opened. Unknown error 13008"
    http://kb.netgear.com/app/answers/detail/a_id/22763/~/readyshare-usb-hard-drive- access-issue-from-a-mac-computer-%28time-machine-or
    In fact it is almost certain that it is an issue of that particular model router and the drive formats it can use.

  • Incredible slowness with LaCie 250 usb drive when trying to delete files

    I connected a LaCie d2 250 gigabyte drive to the usb port of the new Airport Extreme. When I try to delete a folder containing a a fairly large amount of data (40,000 files) it took approximately 30 minutes to tally the number of files and then another 20-40 minutes or so to actually delete the files (put them in the trash). I am wondering if the slow performance is normal? I previously used this drive with a direct connection to my MacBook Pro with the firewire cable. Another thing that is curious is that the folder I was deleting was a backup of my old 'Applications' folder (which does not appear to contain many files - maybe 100 icons at the most). Could the usb cable be the culprit (perhaps is only designed for USB 1.1)? It appears quite a few other people are having some similar issues with drives connected to the usb port. Any other ideas? Thanks.
    MacBook Pro 2.33 ghz   Mac OS X (10.4.8)   Airport Extreme, Airport Express

    I have ruled out the cable as the problem. I attempted to delete another folder and it took well over 1 hour to tally the files so I gave up and clicked the cancel button to cancel the process. As an experiment I used the same usb cable to directly connect to the MacBook Pro and the folder was deleted in less than 30 seconds. There is definitely some issues with the USB port. Hopefully Apple can resolve this with a firmware or software update.

Maybe you are looking for