I need an ethernet cable connection to a non-wireless device that isn't near my current airport express. Can I buy an extra one to plug in near the non wireless device to receive the wireless data and put the signal out in ethernet form?
I need an ethernet cable connection to a non-wireless device that isn't near my current airport express. Can I buy an extra one to plug in near the non wireless device to receive the wireless data and put the signal out in ethernet form?
Yes, you can.
This is a special feature of the AirPort Express 802.11n. You will have to set it up "manually" to "enable Ethernet clients".
If your "main" AirPort Express is an 802.11n version, it is also possible to setup the second Express to "extend a wireless network" to provide additional wireless coverage in addtion to enabling the Ethernet port.
If you need the steps, post back to let us know what operating system you are using on the Mac or PC that will be used for the setup of the new AirPort Express.
Similar Messages
-
What is the process for connecting airport extreme ethernet? I have ethernet cables connected to stereo receiver for internet radio and another to blue ray player. The system preference network indicates "ethernet not connected" with red dot to left of this message. The airport wireless works and has green dot to left of it. The stereo receiver and blue ray player do not respond and give message not connect to internet. Thank you. / cfpirate
It worked for me finally. I took out the DNS numbers in airport admin utility, and restarted the airport express. I do not remember putting the DNS numbers in, I wonder from where the airport express got those numbers.
After restarting, it worked.
Thanks! -
my ipod touch 2g is on black screen.when i connect it to my pc it is not recognizing it.then i opened i tunes and put the phone in dfu mode it says an ipod is detected but it cannot be restored error 1600.plz help me...
Error 1604
This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for the error.
When prompted, click OK.
Close and reopen iTunes while the device remains connected.
The device should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Error 1600, 1601, 1602
Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software. -
I have a power mac, the hard drive is struggling, I have a new hard drive ready to install, after I pull the old one and put the new one it's place and place the old one in the next slot ready to transfer data....how do I start this next step. Do I down load OS, and go to utililities...please just a step by step after hard drives in position.
Hi Susan, you must have a Mac Pro, Powermacs cannot run 10.6.x
Anyway, once you Install the new drive, you likely must Format it...
How to format your disks...
http://www.kenstone.net/fcp_homepage/partitioning_tiger.html
(To Install OSX on an IntelMac the Drive it needs the GUID Partitioning scheme mentioned at the bottom.)
Thanks to Pondini, Formatting, Partitioning, Verifying, and Repairing Disks...
http://web.me.com/pondini/AppleTips/DU.html
Then Install the OS & on first boot of the new install, after a step or two, avail yourself of Migration Assistant & Migrate everything. -
Net connection trouble: "No Ethernet cable connected or the device is not responding"
Hello
I have been plagued by a dropping Net connection for a couple of months, and as it has been getting worse lately I have tried to sort out the problem.
I have simplyfied my connection between the computers and the VSDL fiber modem by bypassing my AirPort Express and Ethernet hub and connecting the three computers directly to the built in ports on the modem.
Since I did that a new error message has started appearing on my Mac Mini, saying that I have no Ethernet cable connected to the modem, or the device is not responding. At the moment I have two of the machines connected, and the Mac Book Air seems to work without problems. There are lights on the Ethernet ports on the modem, and they are lighting up for the iBook even when the Mac Mini connection drops. When the Mac Mini connection drops the lights go off on its Ethernet port on the modem.
This seems to point to some sort of trouble with the Mac Mini. Is there a way to monitor what's going on? Can I use Terminal, for instace? It can't be the settings, and it cant' be the cable, so it must be related to the hardware I suppose. I am using DHCP to connect to the modem.
The connection drops arbitrarily, sometimes for long periods of time, and then comes back up again by itself.
Any ideas for trouble shooting etc?
Best
Hans KarlssonBDAqua
Thanks again. Unfortunately, the problems are back again. Had a stable connection and connected the AirPort again. Everything was working fine. Then all of a sudden the connection dropped again today.h
Connected a LAN cable directly to my MacBook Air and got the connection to work immediately.
Took that cable and connected to my MacMini, again, connection came back immediately.
The AirPort (in Brigde Mode) is also connected, but gives me a blinking orange light, and the same "no cable or (modem) is not responding" message again.
I guess this must rule out hardware problems in the computers.
Ligth for the LAN cable port on the modem connected to AirPort is dead. Moved the cable to another port, light still dead.
Shut down AirPort Express, still same orange blinking light when I switched it on.
I now suspect there is something going on with the AirPort Express. Just bought it, and I had the same problem with it's predecessor, but...
Is there any way to trouble shoot the AirPort Express?
I can connect to it Wirelessly, But AirPort Utility says it has been removed from the Network. In the Network Preferences it says it has a self-assigned IP. For Network Settings I get green lights for everything except Network Settings, which gives me a yellow light. It also says the Internet connetcion is working correctly.
Indeed, when I made the direct Ethernet connection inactive I still get a working connection over WiFi, in spite of the blinking orange light on the AirPort and a yellow light for Network settings in Prefereces....
In the console things look normal:
8/7/12 10:04:27.269 PM Apple80211 framework[231]:
com.apple.message.domain: com.apple.wifi.timeout.scan
com.apple.message.signature: Success
com.apple.message.result: pass
com.apple.message.value: 3149.000000
com.apple.message.summarize: YES
Still confused -
I currently have a motorola surfboard cable modem/router (dual N) that works for all our wireless devices (PCs and MACBOOK) except that our ipad 2 which drops video streaming in the livingroom (works great in the office and bedroom). I'm hoping to purchase a new 5th gen airport extreme and set it up in the living room for the ipad 2 as a repeater/bridge (I think that is the same function) but don't want to have a ethernet cable connecting the motorola to the airport extreme. Is it possible? How? Since the ipad 2 works in other rooms, I don't think it is the ipad 2.
Sorry, but Apple products would not be compatible with your Motorola modem/router using wireless only.
If you need to do this using wireless only, you might want to check with your Internet service provider to see if they have a Motorola product that would be compatible for the purpose that you need.
If you are able to permanently connect the AirPort Extreme to the Motorola modem/router using a wired Ethernet connection, the AirPort Extreme could be configured to provide more wireless coverage that way. -
can i run a printer off the ethernet cable connection without hurting the imac or is the ethernet slot only for internet connection?
Hi, Alan -
How can I connect to both printer (HP 4050n, via direct connection) and internet (via LAN), as my iMac has only one R45 port?
You can, but you'll need to expand your cabling a bit.
You'll need to get an intermediate ethernet hub, switch, or router. That device sits alone, with the Mac, your printer, and your modem/LAN plugged into it.
If you are already using a router, either separate or in combination with the modem (many modems have a built-in router), then you just need a hub or switch.
I use an ethernet switch (10/100/1000) to let both my Macs (a 2010 iMac and an elderly G4 DA model) use my HP4000n printer and my modem. The ethernet switch is a passive device, meaning there's no setup nor instructing it required - it's truly plug-and-play. All four items (two Macs, printer, and modem) are plugged into it via ethernet; both Macs have full-time independent access to the printer and the modem. -
When i use the AE2 as an extra wifi point and put the plug in from Time Capsule than the total networks goes down. what do I wrong?
When i use the AE2 as an extra wifi point and put the plug in from Time Capsule than the total networks goes down. what do I wrong?
You likely first configured the AirPort Express to "extend a wireless network" using wireless only, correct?
If yes, you cannot then connect the AirPort Express using Ethernet....that will crash your network.
The Express must be configured to "create a wireless network". AirPort Utility will do this for you automatically, but you will first need to perform a Factory Default Reset or Hard Reset on the AirPort Express and then start over with the configuration again.
Connect the Ethernet cable to the Express before you open AirPort Utility. Post back if you need more tips on how to set this up. -
I have an Ipad and Iphone but I don't have an Airprint at home but only a WIFI printer, my question is if I connect the wifi printer to Airport express, can I print from Ipad and Iphone ? Please help me if anyone knows about this.
Unfortunately, connecting a non-AirPrint-enabled printer to an AirPort base station's USB port will not make it AirPrint-ready.
You will need to use another solution, like Printopia, to be able to print to this printer from an iOS device. -
The attached file is work inprogress, with some dummy data sp that I can test it out without having to connect to equipment.
The second tab is the one that I am having the problem with. the output array from the replace element appears to be starting at the index position of 1 rather than 0 but that is ok it is still show that the new data is placed in incrementing element locations. However the main array that I am trying to build that is suppose to take each new calculation and place it in the next index(row) does not ap
pear to be working or at least I am not getting any indication on the inidcator.
Basically what I am attempting to do is is gather some pulses from adevice for a minute, place the results for a calculation, so that it displays then do the same again the next minute, but put these result in the next row and so on until the specifiied time has expired and the loop exits. I need to have all results displayed and keep building the array(display until, the end of the test)Eventually I will have to include a min max section that displays the min and max values calculated, but that should be easy with the min max function.Actually I thought this should have been easy but, I gues I can not see the forest through the trees. Can any one help to slear this up for me.
Attachments:
regulation_tester_7_loops.vi 244 KBI didn't really have time to dig in and understand your program in depth,
but I have a few tips for you that might things a bit easier:
- You use local variables excessively which really complicates things. Try
not to use them and it will make your life easier.
- If you flowchart the design (very similar to a dataflow diagram, keep in
mind!) you want to gather data, calculate a value from that data, store the
calculation in an array, and loop while the time is in a certain range. So
theres really not much need for a sequence as long as you get rid of the
local variables (sequences also complicate things)
- You loop again if timepassed+1 is still less than some constant. Rather
than messing with locals it seems so much easier to use a shiftregister (if
absolutely necessary) or in this case base it upon the number of iterations
of the loop. In this case it looks like "time passed" is the same thing as
the number of loop iterations, but I didn't check closely. There's an i
terminal in your whileloop to read for the number of iterations.
- After having simplified your design by eliminating unnecessary sequence
and local variables, you should be able to draw out the labview diagram.
Don't try to use the "insert into array" vis since theres no need. Each
iteration of your loop calculates a number which goes into the next position
of the array right? Pass your result outside the loop, and enable indexing
on the terminal so Labview automatically generates the array for you. If
your calculation is a function of previous data, then use a shift register
to keep previous values around.
I wish you luck. Post again if you have any questions. Without a more
detailed understanding of your task at hand it's kind of hard to post actual
code suggestions for you.
-joey
"nelsons" wrote in message
news:[email protected]...
> how do I create a 1d array that takes a single calculation and insert
> the result into the first row and then the next calculation the next
> time the loop passes that point and puts the results in thsecond row
> and so on until the loop is exited.
>
> The attached file is work inprogress, with some dummy data sp that I
> can test it out without having to connect to equipment.
> The second tab is the one that I am having the problem with. the
> output array from the replace element appears to be starting at the
> index position of 1 rather than 0 but that is ok it is still show that
> the new data is placed in incrementing element locations. However the
> main array that I am trying to build that is suppose to take each new
> calculation and place it in the next index(row) does not appear to be
> working or at least I am not getting any indication on the inidcator.
>
> Basically what I am attempting to do is is gather some pulses from
> adevice for a minute, place the results for a calculation, so that it
> displays then do the same again the next minute, but put these result
> in the next row and so on until the specifiied time has expired and
> the loop exits. I need to have all results displayed and keep building
> the array(display until, the end of the test)Eventually I will have to
> include a min max section that displays the min and max values
> calculated, but that should be easy with the min max function.Actually
> I thought this should have been easy but, I gues I can not see the
> forest through the trees. Can any one help to slear this up for me. -
How to take waveform chart data and put it into an array
Hello all,
I am new to programming in Labview, and am learning basically by watching youtube video and such. My question is how to take a set of random data that I have written code for and linked to a waveform chart, and put the data into an array so I can calculate the mean of the data set. If there is an easier way to calculate the mean of the data set I am all ears, but I need to be able to display the mean on the front panel each time the code is run. I have attached a file of my code.
Thanks
Attachments:
CA1.vi 11 KBWelcome.
If you have not done so, look at the on-line tutorials on Getting Started with LabVIEW on the NI web site.
A chart has a property known as History which retains some previous values. You can get access to the the History property by popping up on the block diagram terminal of the chart and selecting Create >> Property Node. Note that the history length can be set via a pop up menu. The default length is 1024.
Other comments: When you know the number of iteration in advance you should use a for loop rather than the while loop.
You can also use an autoindexing tunnel at the boundary of the loop to create an array. It only contains the values from the current run, unlike the chart history which can retain values between runs (as long as the VI remains in memory). Watch the two Mean indicators as you run this VI several times.
The error wire is to assure that the history property node runs after the loop. Disconnect the wire and watch the Mean and Mean 2 indicators carefully.
The Wait is to slow things down a bit so that you can see what is happening.
Lynn
Attachments:
CA1.2.vi 11 KB -
i just bought the new iPad and want to change the older iPad to my husband and have it use his email account, name and other apps and put the new iPad under my email, accounts etc.
Sync and backup your old iPad one last time and then connect the new iPad to iTunes and you will be given the option to set up as new or restore from the backup of the old iPad. Choose the restore from the backup option. After the iPad restores, follow that with a sync with iTunes.
You can erase the old iPad by going to Settings>General>Reset>Erase all content and settings. Then your husband can set it up as a new device and sync with his own iTunes library or content. -
I am sharing a apple id acount with my family but when I synced my iphone to the computer it erased all of my imformation and put the other phone's imformation on it. I was wondering how I can prevent this from happening?
If the ringtones are on the old device just plug it in and do a transfer of purchases then they will be on the computer to sync to the new device.
-
When I import a commerical CD Itunes will create 2 identical albums and put all of the songs except one into one album and put the other song into the second album that it created. Why is itunes doing this and what can I do to combine them into one album?
I found this to be somewhat helpful: Grouping Tracks into Albums
What I did was to put in the same name for Album Artist in every track. That seemed to do the trick (previously all those fields were empty). It seems like a lot of work for a simple thing.
iTunes knows (or should know) that these tracks were imported from one CD. So why is it relying on incomplete data from the gracenote database? -
Mac Mini won't print via ethernet cable connected to airport extreme
Hi. Thanks for your input in advance. Am about to start throwing things around. I have an Airport Extreme based network which is working fine. The printer is a new HP L7590 which connects to the network with a USB cable connection to the Airport Extreme. Those with laptops and wireless cards are able to print no problem. However my Mac Mini, a 1.25 GHz PowerPC G4 is connected to the printer using a ethernet cable connected to the Airport Extreme. All was working perfectly until I upgraded from Panther to Tiger. I am now running 10.4.11. Now the Mini will not print. The jobs keep stopping. I have removed the printer and try to add it again. The print browser page finds the printer okay and lists it as connecting via Bonjour, but when you tell it to add it, it starts 'searching for new drivers' and then 'gathering printer information' and then it stops responding and I have to force quit it. Any suggestions?? I have already tried all the online mac help suggestions.
Actually it transpires that the G4 laptops are not printing either now.
Maybe you are looking for
-
Incorrect Formatting when converting to .PDF
Hi All, I am experiencing an issue when converting a file to pdf when using pegasus opera program. This has been working fine for ages until the last week or so. My colleague is also using the same setup and it is working fine for her. When convertin
-
Syllable Counter Method sure doesn't work
Ok, I'm writing a program to calculate the Flecsh index, and I wrote this syllable counter method. I'm definitely doing something wrong, because it doesn't work. This is my class 'Manuscript' public class Manuscript public int numberOfSyllables;
-
JDeveloper 11g Handbook : Chapter 10 : MDSRuntimeException MDS-00168
hi If I follow the steps in "Chapter 10: Your First JSF" of "Oracle JDeveloper 11g Handbook: A Guide to Fusion Web Development" (ISBN-10: 0071602380), I get an MDSRuntimeException (MDS-00168) on step 8 on page 359. I tried to find a shorter scenario
-
When firefox opens it pegs cpu usage to 100% what can I do to fix
?????
-
CREATE TABLE integer replaced by NUMBER(38)..
Hi, I am using Oracle 11.1.0.6.O. Create a table using following query. CREATE TABLE VENDOR_MASTER_new ( VENDOR_ID integer, VENDOE_NAME VARCHAR2(50 CHAR), STATUS smallint DEFAULT 1 Table Created. check the table structure using DESC VENDOR_MASTER_new