I need help for network printer installation.

Hi, I want to install Konica bizhub 7228 network copier in Mac v10.6.2. I have some trouble please advise the mathod of installation.

The only printer driver I see for that is a Postscript driver at http://onyxftp.mykonicaminolta.com/download/SearchResults.aspx?productname=7228.
Are you able to define your printer to the network? Can your MacPro see it? Can you describe what you've done and the nature of the trouble ...
Also ... you posted in the iMac discussion ... you might post in the MacPro discussion at https://discussions.apple.com/community/desktop_computers/mac_pro

Similar Messages

Need help with HP printer installation.

Trying to install drivers for an HP OfficeJet 6500 e710n on two machines, an iMac and a MacBook Air, both running OS X 10.7. The printer is a networked printer that I have tried adding to both machines as an IP printer and as a USB printer. With either method the printer is automatically discovered and the drivers are downloaded. After the drivers are installed the process stalls at "Configuring the device..." I have waited at this point for over half an hour with no progress before choosing cancel. I have also downloaded and run the installer from HP with the same results. The only way that I have been able to connect with this printer is by manually configuring an IP printer with the generic PCL drivers. This allows me to print but only in low-res black and white. Any suggestions?

If you force restart the computer on the freeze up, or force quit the printer adding window, does the printer appear in the print and scan system preference? In other words, did the printer successfully install? (is it possible that the setup part of the install failed, but the actual install worked?)
If so, you might be able to set the configurations yourself.
Open up the print and scan system preference. Double click on the printer.
When the printer queue window opens up, you should be able to click on the printer setup button.
Go through all the tabs and set things up the way you like.
HTH
-Graham

Need Help Adding Network Printer

I am trying to add a network printer on a Solaris (Sun OS 5.6) system. I am doing this using lpadmin as outlined in volume 2 of the system admin guide.
The printer appears on the system, but when I try sending a print job, I get the message 'Segmentation error - core dumped' and nothing prints on the printer.
I have added the printer to the etc/hosts and can ping it o.k.
Any ideas would be greatly appreciated.
Thanks

There is info missing from your post that I like to have when considering these issues, so here is what I'm assuming:
You used the command:
lpadmin -p printername -v /dev/null -m netstandard -o dest=printerhostname -I contentype -T printertype
(note: I like -m netstandard instead of
-i /usr/lib/lp/model/netstandard because I'm lazy! they mean and do the same.)
You have the latest version of patch 106235 for lp, which I believe is -09
This is perhaps not the first printer or first attempt at adding a printer on this host.
Possibly this machine was upgraded from a previous version of Solaris?
If you can find the core file (it may be where you issue the lp command or in the /var/spool/lp/tmp directory), you can use the adb command to at least extract the name of the binary that is coring:
adb core
This could be several things that could require anything from a spool clean to an remove and reinstall of the print packages. Any more details you can provide? Perhaps the output of lpstat -p printername -l? Does this happen with any printer you create?

Need help for Lightroom Print&Web Templates

Hi,
I have just downloaded/installed my official Lightroom version (Mac OSX 10.4) and I have realized that there is no Print nor Web Templates accessible in the Template Browser section. I think I have done a mistake since I have erased completely the files from the beta4 version (including obviously the libraires containing those templates) before installing the official Lightroom V1.
Can anybody tell me where/how to get those original Adobe Templates files again. I have tried to re-install several times the V1 version but it does not help. Thanks a lot in advance for your help.

They were in User/Libray/Adobe Lightroom, no at User/Library/Application Support/Adobe/Lightroom
Don
Don Ricklin, MacBook 1.83Ghz Duo 2 Core running 10.4.9 & Win XP, Pentax *ist D
http://donricklin.blogspot.com/

Need help for networking

Hi,
I want to know where can i get help (functions or interfaces) to interact with IP layer in solaris such as (registering a protocol or sending or receiving messages to/from ip etc).
thankx & Regards,
Prasenjit

Well the D-Link is there to provide the wireless signal to the houses 2 laptops
so yes as an access point but not for a better signal more for a continued wireless leg.
(if that makes any sense)
The MacPro does not have Airport capabilities so it is hardwired into the the roof antenna/router...
if possible I would like to first go into my MacPro
then have the MacPro share the signal with the D-Link.
any ideas on how to configure the "sharing" in the Sys. prefs
to do this
and also
any thoughts on how to make the D-Link just an access point without it giving an IP?
thanks for your response
Message was edited by: Shawn Convey

I need help for stop printing.

I am working with Oracle version 7.3 but during the production the users stopped printing and I find this error:
1. ORA - 21636
2. Unable to open the printer description file
3. Check the desformat parameter
But when i check my skill I have no information about this error.
In the unix I find at same time : erro 45 from lock call on file pstatus.
What I can do !
Sincerly
Joco Filipe

I was in a rush this morning and forgot my crystal ball. Please post your code and remember to use the code tags.

Need help getting new printer hp deskjet 3520 setup for eprint and wireless

need help getting new printer hp deskjet 23520 stup for eprint and wireless

Hi Pastorlee7,
I see that you're having problems setting up your printer. I would take a look at the document below.
Hp deskjet 3520
Let me know how it goes.

Fault tolerance for network printing

What options are available to provide fault tolerance for network printing? Currently, all our shared printers are on ServerA. Is it possible to have similar shared printers on ServerB and have the clients automatically switch to Server B if
Server A became unavailable? We don't care about load balancing as much as fault tolerance. Thanks to all who post!

A failover cluster node ? (not in nlb;
Servers in a Network Load Balancing (NLB) failover cluster cannot be used as print servers in Windows Server 2008 )
For environments that require high availability, you can use a failover cluster as a print server. If a node in the cluster fails, all print functionality will fail over to the next node in the cluster. To improve failover times, we recommend
that the administrator for the cluster force failover to each node when new print drivers are installed on the server. During a failover, the driver installation is forced to occur on the active node. The installation of the driver on each node
can require several minutes. Forcing this installation process during maintenance will make sure that any unplanned failovers during usual operation will be very quick, because the drivers will already be installed on each node.
Regards, Philippe
Don't forget to mark as answer or vote as helpful to help identify good information. ( linkedin endorsement never hurt too :o) )
Answer an interesting question ? Create a
wiki article about it!

Need help for Format HD

Hi I need Help for Formating HD so Wat Key need hold on start up for format HD I apprciated you Help

Jesus:
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• With computer shut down insert install disk in optical drive.
• Hit Power button and immediately after chime hold down the "C" key.
• Select language
• Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• _Where available_ +Click on Options button+
+• Select Apple Partition Map (PPC Macs) or GUID Partition Table (Intel Macs)+
+• Click OK+
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
cornelius

I need help getting my printer to work

I need help getting my printer to work

http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Want-Good-Answers-Ask-Good-Questions/td...
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Need help for access list problem

Cisco 2901 ISR
I need help for my configuration.... although it is working fine but it is not secured cause everybody can access the internet
I want to deny this IP range and permit only TMG server to have internet connection. My DHCP server is the 4500 switch.
Anybody can help?
         DENY       10.25.0.1 – 10.25.0.255
                          10.25.1.1 – 10.25.1.255
Permit only 1 host for Internet
                10.25.7.136 255.255.255.192 ------ TMG Server
Using access-list.
( Current configuration )
object-group network IP
description Block_IP
range 10.25.0.2 10.25.0.255
range 10.25.1.2 10.25.1.255
interface GigabitEthernet0/0
ip address 192.168.2.3 255.255.255.0
ip nat inside
ip virtual-reassembly in max-fragments 64 max-reassemblies 256
duplex auto
speed auto
interface GigabitEthernet0/1
description ### ADSL WAN Interface ###
no ip address
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
no atm ilmi-keepalive
interface Dialer1
description ### ADSL WAN Dialer ###
ip address negotiated
ip mtu 1492
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username xxxxxxx password 7 xxxxxxxxx
ip nat inside source list 101 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.25.0.0 255.255.0.0 192.168.2.1
access-list 101 permit ip 10.25.0.0 0.0.255.255 any
access-list 105 deny   ip object-group IP any
From the 4500 Catalyst switch
( Current Configuration )
interface GigabitEthernet0/48
no switchport
ip address 192.168.2.1 255.255.255.0 interface GigabitEthernet2/42
ip route 0.0.0.0 0.0.0.0 192.168.2.3

Hello,
Host will can't get internet connection
I remove this configuration......         access-list 101 permit ip 10.25.0.0 0.0.255.255 any
and change the configuration ....      ip access-list extended 101
                                                            5 permit ip host 10.25.7.136 any
In this case I will allow only host 10.25.7.136 but it isn't work.
No internet connection from the TMG Server.

I need help getting past the installation error "windows cannot fint TEMP file"

I need help getting past the installation error "windows cannot find TEMP file"

Seems like some who have tried two devices on the JMICRON IDE port have had trouble. Try without the hard drive and see if you get that error. If that is the case I would try a PATA to SATA converter for your hard drive and connect it to one of the Intel SATA Ports.
http://www.newegg.com/Product/Product.aspx?Item=N82E16812107112
http://www.amazon.com/ADDONICS-IDE-SERIAL-CONVERTER-ADIDESA/dp/B000090169
http://www.compusa.com/products/product_info.asp?product_code=339900#ts
http://www.xpcgear.com/ide2sata.html
http://www.ubuyitdirect.com/-p-1045.html?currency=USD
http://www.satasite.com/sata-ide-converter.htm
http://www.pcgears.com/default.aspx?oid=187150

Pls i need help for this simple problem. i appreciate if somebody would share thier ideas..

pls i need help for this simple problem of my palm os zire 72. pls share your ideas with me.... i tried to connect my palm os zire72 in my desktop computer using my usb cable but i can't see it in my computer.. my palm has no problem and it works well. the only problem is that, my desktop computer can't find my palm when i tried to connect it using usb cable. is thier any certain driver or installer needed for it so that i can view my files in my palm using the computer. where i can download its driver? is there somebody can help me for this problem? just email me pls at [email protected] i really accept any suggestions for this problem. thanks for your help...

If you are using Windows Vista go to All Programs/Palm and click on the folder and select Hot Sync Manager and then try to sync with the USB cable. If you are using the Windows XP go to Start/Programs/Palm/Hot Sync Manager and then try to sync. If you don’t have the palm folder at all on your PC you have to install it. Here is the link http://kb.palm.com/wps/portal/kb/common/article/33219_en.html that version 4.2.1 will be working for your device Zire 72.

By. i need help for photoshop connective...from 2 days ave a problem of connective.thank you

by i need help for my photoshop connective..if you ceck problem please.

Does your Cloud subscription properly show on your account page?
If you have more than one email, are you sure you are using the correct Adobe ID?
https://www.adobe.com/account.html for subscriptions on your Adobe page
If yes
Some general information for a Cloud subscription
Cloud programs do not use serial numbers... you log in to your paid Cloud account to download & install & activate... you MAY need to log out of the Cloud and restart your computer and log back in to the Cloud for things to work
Log out of your Cloud account... Restart your computer... Log in to your paid Cloud account
-Sign in help http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html
-http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html
-http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html
-http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html
-ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp
If no
This is an open forum, not Adobe support... you need Adobe staff to help
Adobe contact information - http://helpx.adobe.com/contact.html
-Select your product and what you need help with
-Click on the blue box "Still need help? Contact us"

I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

http://www.apple.com/support/itunes/contact/

I need help for network printer installation.

Similar Messages

Maybe you are looking for