I need help here with my Wireless Broadband w/speedbooster router....
hi...
i have here my Wireless Broadband w/speedbooster router. And yet i cant still configured it out.. i already followed the instructions on the CD but still it doesnt work... What should i do??? My ISP is using a DHCP address type.... my IP is 192.168.1.100 den my subnet Mask: 255.255.255.0 and my default Gateway: 192.168.1.1.... What should i do???
access the router using http://192.168.1.1 .. the default login password is admin ..
on the web interface , click on the "mac address clone" subtab , enable it , click clone and save settings .. do a power cycle ..
click on the "status" tab and check whether it has a valid internet ip add ..
Similar Messages
-
Ok i need lots of help here... i have a WRT54G router and...
ok i need lots of help here... i have a WRT54G router and trying to hard wire a computer to it and wirelessly connect to a laptop... i have dsl internet connection... the power light is blinking constintly and when i try to setup the router the default password doesnt work already tried to reset the router and that didnt help... any thoughts> thanks
the power led blinking all the time can be caused by a corrupt firmware, or a defective power adapter, try doing a hard reset, you may need to do it a couple of times, and then power down both the modem and router.
after a couple minutes, power up the modem, wait for the link led lights up, then power up the router and look for it to link up with the modem, at this time the power led on the router should be on solid if all is ok.
if it still don't light solid, you may need to do a firmware update, or the router is defective. -
as stated above
What is the best way to remotely access my sister in laws Mac who lives in another city to help her with her computer problems?The best way? Get her to bring it to you, especially if she makes good cakes.
Apples Back to my Mac isn't really suitable for this - it is designed for a single person who wants their Apple ID on the system. It would mean she would have to share hers with you & you would also have to setup her Apple ID on your Mac - it is messy & causes trouble with iCloud, iTunes etc.
You can try Messages if she is able to begin a session with you, see the 'invite to share screen' in the menus, weirdly you need to use a service that isn't from Apple.
Messages (Mavericks): Share your screen
It may be better if you to setup LogMeIn or GoToMyPC. They should 'dial out' & maintain a constant connection so you can login whenever the Mac is powered up. It won't, require a human to initiate the process at the other end, just be aware that the router may cause issues depending on what is configured, you may need settings to enable automatic port forwarding - it really depend on which option you choose. -
My iphone 4S Black 16 GB with IOS 7.0.4 turns off randomly in low battery less than 15% and also when I am taking pictures from my front camera in low battery of 30%. This is happening very often. Can someone help here with advise? The phone is slightly more than 2 years bought from singapore I live in India
Either your battery is failing or your battery gauge needs to be recalibrated. Start by recalibrating:
When it shuts off charge for just a minute or two, then restart (hold HOME and SLEEP until an Apple logo appears). Deliberately run the battery down until the phone shuts off at 1%. If it shuts off above 1% repeat the above until you get to 1%. Then charge for 4 hours with the wall charger without using the phone. This process will recalibrate the battery gauge.
To prevent this from happening again about once a month run the battery all the way down to 1%, then continue until the phone shuts off. Apple recommends this in their battery help article, but they don't say why you should do it. The have some hokum about "keeping the electrons moving." Honestly! The iPad battery tip gives the correct reason.
If this does not resolve the problem you most likely need a new battery. If you are near an Apple store take the phone in and they can test the battery for you. -
Need help here!!!, y550 vista can't update to windows 7
need help here
im using y550, p8700, 500 gb, windows vista home premium 32 bit
i'm trying to update my computer to windows 7, but im always stuck in 62%
i tried this method
Restart the computer. Then, your computer will roll back to Windows Vista.
Click Start, right-click Computer, and then click Properties.
On the Advanced tab, click Environment Variables.
Under System variables, click New.
Type MIG_UPGRADE_IGNORE_PLUGINS in the Variable name field.
Type IphlpsvcMigPlugin.dll in the Variable value field.
Click OK three times to close the dialog boxes.
Start the upgrade installation again.
did not work!!!!!!!!!!!!!
i even read this forum, actually we have simliar problem,
http://social.technet.microsoft.com/Forums/en/w7it proinstall/thread/6e6323b0-4b91-4a31-86c5-bfbfaac...
anyway this the error i got
C:\$Windows.~BT\Sources\Panther\setuperr.log
2010-06-12 16:33:36, Error Number of Enumerated Devices = 19[gle=0x00000103]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=00000002x[gle=0x00000003]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:37, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:41, Error Number of Enumerated Devices = 19[gle=0x00000103]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=00000002x[gle=0x00000003]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:33:41, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:26, Error Number of Enumerated Devices = 19[gle=0x00000103]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=00000002x[gle=0x00000003]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:26, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:29, Error Number of Enumerated Devices = 19[gle=0x00000103]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x[gle=0x80092004]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=00000002x[gle=0x00000003]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 16:34:29, Error Failed to find driver file path. Error=ffffffffx[gle=0x00000003]
2010-06-12 17:06:11, Error [0x080389] MIG Failure while calling IDiscovery->Gather for Plugin={ServerPath="%SystemRoot%\System32\Setup\ms dtcstp.dll", CLSID={342992B2-913C-4C36-9DB7-6C68ABD1F079}, ThreadingModel=Apartment}. Error: 0x80070002
so if anyone can help me, please, i wanna update to win 7, this is my 6th time trying to reinstall, i believe all my drivers are up to date which can be found here
http://consumersupport.lenovo.com/ot/en/driversdow nloads/APR_Driver_List.aspx?CategoryID=207087&OS=...
i don't wanna do clean install unless no one can help me....
thanksPlease go through this Knowledge Base article.
You need to download the Automated solution provided by microsoft from the given link within the article.
Hope this helps
Cheers and regards,
• » νιנαｿѕαяα∂нι ѕαмανє∂αм ™ « •
●๋•کáŕádhí'ک díáŕý ツ
I am a volunteer here. I don't work for Lenovo -
Need help here, a friend died from mesothelioma and his family gave his ipad to us for our children. I reset the ipad in iTunes on the computer and it has find my iPhone on it , now the ipad dont start or boot up again. How do I get for that because I am not able to get a hold of him obviously?
Just had an employee terminated most acrimoniously and had an iPhone 5C that was a brick. Apple support can help remove the lock. Better hold onto your original receipt and record the Serial# ! I do not mean the MEID or IMEI but the Serial# found on the original box or Settings>General>About. In my case no receipt or Serial#. 2 hours on the phone between Apple and Verizon and got what was needed. Submitted form and got reply to allow 2-10 business days.
Here is the form I had to complete and sent to [email protected]..
ORIGINAL SALES INFORMATION:
PRODUCT PURCHASE DATE:
INVOICE/RECEIPT NUMBER:
PRODUCT SERIAL NUMBER:
PRODUCT IMEI/MEID:
PRODUCT DESCRIPTION:
BUSINESS/INSTITUTION NAME:
REQUESTOR NAME/TITLE:
PHONE NUMBER:
STREET ADDRESS:
CITY:
STATE:
POSTAL CODE:
EMAIL ADDRESS:
UNLOCK AUTHORIZATION STATEMENT: I [YOUR NAME] representing
[BUSINESS/INSTITUTION NAME] authorize Apple, Inc. to unlock the devices listed.
Best regards,
The Apple Support Team -
Need help here! I'm out of options. Computer can't see the wireless network
Sorry for the novel, but I have to tell you what is going on with my computer. I also need to vent because I’m extremely frustrated. I want to make sure I give as much info as I can we can get this fixed. I’m done with trying to figure this out on my own!!!
I’m having a major issue with the wireless network connection on my desktop. I’ve tried everything and I can’t figure out what it’s doing.
First of all, my wireless router is set up correctly (according to the Sticky), has active security, and works fine. It has nothing to do with the router. I’m sure of it.
Here’s a quick history:
When I was at my first residence in Chicago and bought a Linksys wireless N router in May 2008. My computer was about 30 feet away from the router and everything worked fine. Always found the router and never lost connection.
I moved to a new place in September 2008 and used the same router, computer, etc. at my new place. The computer was only about 7 feet away from the router this time, but I used the wireless connection instead so I wouldn’t have a network cable lying across the floor. At first everything worked fine. No issues. Then, one day out of the blue, my desktop lost connection with the router. My router didn’t even appear as an Available Wireless Network. I rebooted everything and that seemed to fix it. OK, issue fixed, right? Wrong. It did it again the next day. I rebooted everything, but it still couldn’t find my router. It did see lots of other wireless routers in the area though so I know the wireless card was working. It just didn’t see my router.
This went on for a while. Sometimes it would see my router and connect then it would lose it again. I thought maybe it was the router going bad. Well, I have a notebook computer too so I tried it. It has found my router every time and has never lost connection. I had it sitting on top of my desktop even to see if there was some sort of dead spot in my condo, but the notebook found my router just fine.
Sometimes my desktop would see my router, but it wouldn’t be my network name. It would call it “Home” or something. I know it was my network because it was the only network with maximum (Excellent) signal strength. I’m thinking it must be some sort of association issue. For some reason it doesn’t associate my router as an available network. I don’t understand that.
I tried everything: Ad Aware, Live OneCare, registry cleaners, driver updates, restore points, pretty much anything I found in the forums. Nothing worked for long if at all. It’s like my desktop only finds my router when it wants to. Note: The only thing that would work sometimes was if I clicked “Repair.” Sometimes that would work. I finally gave up and connected my desktop via network cable and unhooked my wireless card. I never lost connection as long as it was hard-wired.
The drama continues. I recently moved to Iowa and set up my network here. I’m using the same router, same desktop and wireless card, same notebook computer, etc. I went ahead and tried the wireless card on my desktop again. It worked just fine! No connection issues at all. It connected and stayed connected. I thought, “Well, that’s strange. It must have been something with the condo in Chicago. Oh well!” It worked fine from February 5 until March 10. Now it’s doing it again!!!! The notebook is about 3 feet away and sees the router just fine.
Here are the facts:
I’m using a Linksys WRT300N Wireless-N router.
I’m using a Linksys Wireless-N PCI WMP300N Adapter (about 18 months old).
I’m running Windows XP on the custom built desktop and Windows Vista on the HP notebook.
I built this computer about 5 years ago and have not done any major upgrades for 2-3 years. The only thing I added was the wireless card. I also changed out the HD in January 2009 and did a data migration right before I moved to Iowa in February. All of the networking issues were going on well before I did the data migration though so it has nothing to do with that. In fact, I had my computer hard-wired into my router at the time of the data migration and the wireless worked fine (for a little while) after I moved to Iowa. So if anything, the data migration seemed to help with my wireless connection.
All drivers are up to date.
Using Windows Live OneCare and have run complete scan: nothing found.
Using Ad Aware and have run complete scan: only found cookies and deleted them but didn’t fix issue.
Ran WinsockxpFix but that didn’t help.
Ran TweakNow RegCleaner Standard but that didn’t help.
Right-clicking the wireless icon, I try to view Available Wireless Networks. The window comes up and shows me other wireless networks in the area (2 available right now), but doesn’t show my network at all. I click “Refresh network list” and 1 or 2 of the other networks will come up, but mine is still not shown.
I’ve clicked “Repair” and get this message: “Windows could not finish repairing the problem because the following action cannot be completed: Connecting to the wireless network.”
If I go to Control Panel, there is a Wireless Configuration Utility program from Broadcom. When I open that here is what I find:
It is not managing my wireless networks.
Under the “Wireless Networks” tab I see my Network with an “X” over the router icon to the left of it and a locked security icon to the right of it.
No information under the “Link Status” or “Statistics” tabs.
The “Site Monitor” tab shows my wireless network and the other 2 networks in the area (although they drop in and out because of signal strength). My network is always present even though the signal strength bounces up and down. This tab shows that my network is secure, 802.11 is g and n, speed is 270 mbps, Channel is 9, and Signal bounces from orange/red to green. Data encryption is (m)TKIP, TKIP, WPA-PSK.
I was going to use my notebook to post this message since it has been connected for 2 days without ever losing connection. It shows Very Good signal strength and is about 3 feet away from my desktop.
Update: My desktop just connected to my network after sitting there for 2 hours. Good to Very Good signal. Broadcom tool shows the connection and now has information in the Link Status and Statistics tabs.
Cancel that. It just lost connection again. It was only connected for about 5 minutes. There is no change in signal strength according to Broadcom though. In fact, Broadcom shows better signal now that I lost connection.
Now, it just connected again (on its own) after sitting there for 10 minutes! I’ve been surfing the web on my desktop for 45 minutes now and I’m using my desktop to post this message. What the heck?!!! This is what it’s like. Aggravating huh?
Well, that’s all I can think to write. What else do you need? Can anybody help me with this?
I’m confused. Please help!
Thanks a lot!!!
Jake
Message Edited by JakeT on 03-12-2009 02:54 PMThanks but it's just my desktop that doesn't see it though. My notebook sees it everytime, even at the same exact time that my desktop doesn't see it. For example yesterday when I was typing up this post, I was typing up the post on my notebook because my desktop didn't see the router. I don't think it has anything to do with the router actually, but I wanted to see if anyone on here has encountered this issue before. Other forums have similar issues but I've tried all of the fixes I found elsewhere and they didn't work.
Any other ideas?
Thanks! -
Need Help setting up 2 wireless internet computers with 54g wireless router
I setup the 54g wireless router using the setup disk. It appears to have worked find and the first laptop has wireless internet. I am not familiar with setting up a totally wireless network so I am not sure if I did the rest right. I then setup the 54g wireless internet router on the 2nd computer. It appears to have loaded but will not connect to the internet. I looked at the linksys setup etc... for both computers and all is the same including the WPA key, IP address, and the rest. No differences noted. I have no idea why the 2nd computer does not have wireless internet access. It has wired access only. The 2nd computer shows the wireless network but won't connect to it. I click on it and hit refresh and nothing happens. I am at a loss as to what to do now.
With 2 wireless computers, must there be a main computer and a secondary computer? The 1st computer also doesn't have access to windows network setup for some reason. It tells me to go to the knowledge base at microsoft.com and look up 871122. No idea why the windows network setup is not working. It did work before I got a new cable service provider and modem. However, the windows network setup is working on the 2nd computer. Any help is appreciated.does the 2nd computer even need the router info loaded into it like the 1st computer or should it be enough that the wireless network was created on the 1st computer? In other words, would having the router info loaded in both computers cause the 2nd one to not connect? I have spent hours on this and I am very confused now.
My router connects fine to the cable modem. the 1st computer connects fine to the router and gets the wireless internet without a problem. Again, the 2nd computer shows the network name but won't connect to it. help please!! -
Need help setting up eyeHome - Wireless with AX
Hi all,
I am trying to setup eyeHome over a wireless connection using Aiport Xtreme.
I have no problem connecting to the internet through AX and my D-Link ethernet modem (thanks to Apple Support), works perfectly.
But when I try and add eyeHome to this equation everything seems to stop working and I have to reset my AX and start all over again.
The problem seems to occur when I setup try to set up WDS over, I get an error about not being able to configure the base. Elgato's (eyeHome's makers) instructions on how to setup the device arent clear.
Please help me out on this. Cheers.A little confused actually. Why does D-Link DSL- 300T have to support WDS, when it is the wireless adapter provided by Elgato which is having problems being configured. The setup is as follows?
WITHOUT ELGATO WIRELESS ADAPTOR ATTACHED:
ADSL LINE --via rj cable----> DLINK MODEM
DLINK MODEM ---via ethernet cable----> AIRPORT EXPRESS
AIRPORT EXPRESS - ----> iMac G5
WITH ELGATO WIRELESS ADAPTOR ATTACHED:
ADSL LINE --via rj cable----> DLINK MODEM
DLINK MODEM ---via ethernet cable----> AIRPORT EXPRESS
AIRPORT EXPRESS - ----> iMac G5
EYEHOME BOX ----via scart----->TV
WIRELESS ADAPTOR----via elgato's ethernet cable---> EYEHOME BOX
EYEHOME BOX---communicates via WIRELESS ADAPTOR through AX--->iMac
Hope this makes sense -
I need help getting a Novatel Wireless Merlin S720 to work on my G4 PB
I need help with "Sprint Mobile Broadband Card Novatel Wireless Merlin S720.
I have a Mac PowerBook G4 running 10.4.8 as follows:
Machine Name: PowerBook G4
Machine Model: PowerBook3,3
CPU Type: PowerPC G4 (2.1)
Number Of CPUs: 1
CPU Speed: 667 MHz
L2 Cache (per CPU): 256 KB
Memory: 1 GB
Bus Speed: 133 MHz
Boot ROM Version: 4.2.9f1
I was told by a "Sprint PCS Level 2" Tech that if
I got one of the "Sprint" cards that I would have to
set it up on a "Windows" Laptop and then call a
"Sprint PCS Level 2" tech and have them walk me
through setting it up on my PowerBook G4...
I purchased a "PanTech PX500"... set it up on my
"Windows" laptop and called to be told that I should
have purchased a "Novatel S720" and the the "PanTech"
would NOT work in my Powerbook...
I took the "PanTech" back and finally (after of month of looking
for one in a Sprint Store to no avail) ordered on from Sprint's
Tel-Sales unit...
When it arrived I set it up on my "Windows" laptop and called
back to a Sprint Level 2 Tech... I got a tech that was very helpful,
however, was NOT able to get the "Novatel S720" to work... He
told me I should have purchased a "PanTech PX500"!!!
This morning I went to a "Sprint Store" and was told that they had
sold several "Novatel S720's" to Mac owners and suggested that
I keep the "Novatel S720" and even though they could not set it up
on my Mac... they suggested that I call back to another Level 2 tech...
Is there anyone out there that can help me get this working???
Many Thanks In Advance!!!
THX
JohnI went to the Sprint Store in St Peters MO and one of the Sprint
Associates told me that she had sold several Sprint cards including
20 or so S720's to a customer of her's..
A large graphics house based in St Louis.
She emailed the Senior VP there and ask that he contact me
if he could/would help...
I received an email from him in less than 4 hours and he
directed me to their in-house tech dept!
I called and talked to the person that he had directed me to
and that person told me that it was a little tricky... You have to do
some modification of the "Code" in the Kernel...
He said if would bring my Mac & the card over the next day
at 10AM it would take him about 10 minutes to get me up and
running!!!
I ask what the charge would be??? He said... "The Boss is a
real Mac Guy... Just Bring it over and we'll get you fixed
up!!! It's a Mac thing!!!"
It works Great!!! I've used it in several areas around the MidWest
and my next road trip will include IN, IL, MO (KC), KY, TN, AL, FL,
GA and SC... That will be the test!!!
I'm finding that I'm able to get on line with the Sprint Card in places
that I don't get very good Sprint PCS Cel service...Must be the
Sprint/NEXTEL combination!
I've been a Mac owner/user/teacher since early '84... It's
GREAT to me a Mac Person!!!
Thanks for your reply and taking the time to help!!!
THX
John -
Need help extending my current wireless connection
Hi guys,
I'd like to extend my current connection so that it reaches the two back bedrooms in the house. At the moment, we're lucky if we see one bar there. A friend spent a few hours this week trying to figure this out and finally gave up.
Our internet provider currently has us set up with a:
Huawei router HG655b
As options, I currently have access to an airport express (802.11n) as well as a Linksys E1000 wireless-N router and wonder if either could be used simply to extend the current wifi signal to reach the back bedrooms(mostly for ipads and ipods) OR completely replace the current Huawei router with either device to increase the current router's poor signal range.
I do most of my work in one of the rooms adjacent to the back two bedrooms and currently have a macbook pro connected by ethernet cable. I'd like to use this room to set up the airport express or linksys router if need be. On another note, the only system we have here with cd access is the macbook pro with Lion OS X. When I tried to install the Linksys router, we got an error message saying it wasn't compatible with Lion yet. Attempts to set it up without the cd have proven futile.
Thanks for any help in advance guys, we're totally clueless at the moment....Hi again huluvu,
Changing the security settings on my Huawei didn't seem to make any difference unfortunately. I'm really not sure what the problem could be with my express. I am living in the middle east at the moment but I don't think this should matter as I know lots of others here who are using various airport products.
The good news is that I was able to increase the signal strength by setting up and creating a new network on the Linksys router. We're now able to get two bars(hey, it's better than one) and I'm wondering if I can physically move the router to another room closer or actually in one of the bedrooms. I currently have the Linksys router sitting next to and connected to the Huawei by ethernet cable. I haven't tried it yet as I'm worried about causing problems with the newly created network but I wonder if I could now unplug the ethernet cable on the Linksys and move it and plug it in in one of the back bedrooms(without ethernet cable) or does it need to be connected to the Huawei by ethernet. If so, I guess I could run the ethernet cable into the bedroom as well but would prefer not to unless need be.
Thanks again for the detailed info. I had the iStumbler app before but am now using the KisMAC app which I believe does pretty much the same thing. I'm going to look at the "wifi scanner" app now.
Cheers! -
Need Help/Advice with Photo Web Gallery coming from SQL Database
This is my first attempt at a database driven website. I assume what I am trying to accomplish should be fairly easy for more experienced but I am stuck at this point.
First, let me explain what I am trying to accomplish.
I want to create a thumbnail photo gallery displayed in columns and rows. I want to be able to hover over or click on the thumbnail image and have a lightbox script display the image over the thumb page. I am developing locally right now with intent to upload to the hosting site upon completion.
I am developing with ASP vbScript pages. I have an SQL database where the paths to the image thumbnails and pictures are stored in a table. On the gallery page, I have created a div tag to hold my image recordset. Within this div, I have inserted 3 absolute positioned divs to hold the pictureID, the pictureName and the image inserted as a datasource. I then inserted the information from the bindings panel of my recordset. Last, I used a horizontal looper extension from Tom Muck to get the thumbnails to display in columns and rows. Everything works up to this point just fine.
Now, I want to be able to hover or click on a thumnail image and have it displayed in a lightbox. I downloaded and used a javascript called Lightbox 2 which contains 3 javascript files and a css stylesheet. I inserted the files into the head tag like instructed to but could not get things to work properly. Here is where I need help. Currently, I am clicking on the thumbImage binding within the image Div and creating a link holder. I am then binding the larger pictureImage to it with the a.href selected in the bind to. I am then adding the command to call the lightbox javascript. Now, when I test my page, my thumbnail images do not show up (my alt text does in its place) but the links are in place and you can click on the alt text and it will return the correct larger image, but not in the lightbox, just in a new window with no styles.
Am I going about this correctly? Can you use lightbox scripts with data-driven galleries? Does anybody have any suggestions of what I may be doing wrong or missing? Are there better ways to go about accomplishing this?
Any help would be appreciated as this dynamic data thing has my head spinning. Although I know a database is needed to simplify the update and maintenance of the photos while allowing them to be searchable by keywords and tags also set up in the database.
ThanksAs I explained, I am developing locally a the moment. I will see about getting the databased moved up to the hosting server and then provide a link for an example.
In the mean time, can you or anyone else explain a way that you would go about displaying an image thumbnail photo gallery laid out in rows / columns, with any lighbox script that would overlay the larger image over the existing page instead of opening a new browser window?
I don't have to use the method I tried to describe.
In all of the lightbox examples I have looked at thus far, they give instructions on how to append that javascript to a single static image or a group of static images, not images from a datasource. That is where I am getting confused.
Don't know if this will help or not but please see code below:
Javascript and CSS positioned in head tag
<!--beginning of lightbox script with css -->
<link href="CSS/lightbox.css" rel="stylesheet" type="text/css" />
<script src="Scripts/protype.js" type="text/javascript"></script>
<script src="Scripts/scriptaculous.js?load=effects,builder" type="text/javascript"></script>
<script src="Scripts/lightbox.js" type="text/javascript"></script>
<!--end of lightbox script with css -->
Calling for javascript in the galleryimage div when hovering over thumbnail image
<!--beginning of gallery div -->
<div id="gallery">
<p>
<!--beginning of galleryImage div -->
</p>
<table width="400" border="0" align="center" id="galleryNav2">
<tr>
<td width="100" align="center"><% If MM_offset <> 0 Then %>
<a href="<%=MM_moveFirst%>">First</a>
<% End If ' end MM_offset <> 0 %></td>
<td width="100" align="center"><% If MM_offset <> 0 Then %>
<a href="<%=MM_movePrev%>">Previous</a>
<% End If ' end MM_offset <> 0 %></td>
<td width="100" align="center"><% If Not MM_atTotal Then %>
<a href="<%=MM_moveNext%>">Next</a>
<% End If ' end Not MM_atTotal %></td>
<td width="100" align="center"><% If Not MM_atTotal Then %>
<a href="<%=MM_moveLast%>">Last</a>
<% End If ' end Not MM_atTotal %></td>
</tr>
</table>
<p> </p>
<table align="center" id="HorzLooper">
<%
startrw = 0
endrw = HLooper1__index
numberColumns = 5
numrows = 5
while((numrows <> 0) AND (Not rs_ssfGallery.EOF))
startrw = endrw + 1
endrw = endrw + numberColumns
%>
<tr align="center" valign="top">
<%
While ((startrw <= endrw) AND (Not rs_ssfGallery.EOF))
%>
<td><div id="galleryImage">
<div id="galleryThumb"><a href="images/pic/<%=(rs_ssfGallery.Fields.Item("picture_url").Value)%>"rel="lightbox"><img src="images/thumb/<%=(rs_ssfGallery.Fields.Item("thumb_url").Value)%>" alt="<%=(rs_ssfGallery.Fields.Item("alt_url").Value)%>" /></a></div>
<div id="galleryImageID"><%=(rs_ssfGallery.Fields.Item("picture_ID").Value)%></div>
<div id="galleryImageFamily"><%=(rs_ssfGallery.Fields.Item("family").Value)%></div>
</div></td>
<%
startrw = startrw + 1
rs_ssfGallery.MoveNext()
Wend
%>
</tr>
<%
numrows=numrows-1
Wend
%>
</table>
<p> </p>
<table width="400" border="0" align="center" id="galleryNav">
<tr>
<td width="100" align="center"><% If MM_offset <> 0 Then %>
<a href="<%=MM_moveFirst%>">First</a>
<% End If ' end MM_offset <> 0 %></td>
<td width="100" align="center"><% If MM_offset <> 0 Then %>
<a href="<%=MM_movePrev%>">Previous</a>
<% End If ' end MM_offset <> 0 %></td>
<td width="100" align="center"><% If Not MM_atTotal Then %>
<a href="<%=MM_moveNext%>">Next</a>
<% End If ' end Not MM_atTotal %></td>
<td width="100" align="center"><% If Not MM_atTotal Then %>
<a href="<%=MM_moveLast%>">Last</a>
<% End If ' end Not MM_atTotal %></td>
</tr>
</table>
<!--end of galleryImage div -->
</div>
<!--end of gallery div -->
Thanks for any help or suggestions. -
Need help ASAP with photoshop elements 11
Please I need help its photoshop elements 11 but I can't put up the pic I need help with could someone help me out by using Facebook, Amanda Jayne Clarke I have a pic of a little girl n a horse
Please i need help ASAPwell you can find many tutorials about how to change background in Photoshop Elements. It ranges all the way from using magic extractor to making a selection using lasso and magnetic lasso tools. But I really prefer using a mask for it. Here is how I would change the background of image A and use Image B as the background.
Open image B in photoshop elements editor- expert mode.
go to file->place and choose the image A to place over image B
go to layers panel by choosing Window-> layers from menu bar. Right click the layer A choose simplify layer.
with layer A selected, choose layer>layer mask> reveal All from menu bar. It would create a layer mask on the layer A.
Select the mark layer of layer A, choose the brush tool and change foreground color to black. Paint all over the are you want to remove from the layer A. if you make an error, change the color white to get your image area back. it is a good practice to use lower opacity(~60) while using layer mark as it gives you more control over with how much opacity you want to remove the background
Happy Editing -
Need Help Please with Ipod 20G
Long story short....I had my Ipod 4G and computer stolen several month ago on a business trip(have police report). A friend of mine recently purchased a new Video Ipod and gave me his old 20G...pretty nice of him! I am about to have iTunes loaded on to my new computer. Here are my questions I need help with please.
1. Will I need to setup a new iTunes account or can I use my old one?
2. Will I have to reset my newly acquired Ipod before I can place my music on it? I did back up about 80% of the songs from my old Ipod. Or will I be able to keep the 1500 songs my friend placed on it?
3. Or would it be easier for me to give him back his, cough up the $300 dollars for a new one and start all over?
Can't think of anything else I might need to know. If there is something I am missing and you could help fill in the blanks for me I would truly appreciate the help.
Thanks so much!!
20G Windows 2000
20G Windows 20001. No. You can use your old one.
2. Will I have to reset my newly acquired Ipod before I can place my music on it? No, but iTunes may automatically do this, I will explain.
I did back up about 80% of the songs from my old Ipod. Or will I be able to keep the 1500 songs my friend placed on it?
Sorry, but it would not be legal to keep the 1500 songs on this iPod that were your friend's songs, assuming that he's still using/listening to them on another computer.
3. No, I think it would be worth it to keep going, and use the 20GB iPod on your computer. It's not many hoops to jump through, and you should be up and syncing in no time.
Overall, it's fairly easy, and I would suggest that you keep going with this iPod.
My note from question #2:
If you connect an iPod that hasn't been attatched to your computer before, iTunes will most likely display [to the effect of] this message when you connect the iPod for the first time:
"The songs on the iPod "~~" are linked to another iTunes library. Would you like to replace the content of the iPod with this current iTunes library?"
Be sure to click on "NO" when you recieve this message.
Then, click on your iPod's name in the left panel of iTunes.
Click on the "Music" tab.
Deselect "Sync Music" if it is already set to this option.
This means that your iPod is on manual managing now, instead of iTunes automatically transferring songs to your iPod, or deleting them, which is not what you want at this time.
Now, if you have any songs on the iPod that you need to keep (i.e., if you have some of your songs on this iPod)you have a few options to transfer your iPod songs to your computer.
Method 1 - Manually transfer your iPod songs to iTunes using MacMuse's post. See it here -> iPod songs to computer (MacMuse post)
Method 2 - Add your iPod's folder into the iTunes library (via iTunes). Read this post here -> Using iTunes settings to transfer iPod songs to iTunes
Method 3 - Use a third-party program to get the transferring done. For a Windows computer, CopyPod should work good. Also, you can try out YamiPod
I hope that info helps you.
-Kylene -
Need Help using WRT54GL as Wireless Bridge for Xbox
Hi.
I need help configuring my WRT54GL as a wireless bridge for my xbox.
I have a Billion BiPAC 7404VGO currently in service as my main router/modem. i.e. I have my ADSL connection and PC connected to this. I also connect to this with a laptop.
I have an original xbox at the other end of the house (cat5 NOT an option).
Basically I want to connect my xbox to the rest of network. I have a WRT54GL I can use for this. I just dont know how to set it up.
The WRT54GL has Firmware Version: v4.30.7 (out of the box).
My Wireless network is using WPA.
I have a VPN setup through to work via the Billion.
The idea is to stream media from my PC to the xbox (media centre).
Any help would be HUGELY appreciated.
Thanks in advance.
KatmanA wireless router is a device which requires its own wired internet connection. A wireless router is not a wireless access point like the Linksys WAPs. A wireless router does not connect wireless to other wireless routers/APs with standard Linksys firmware. With Linksys firmware you need a WAP54G or similar. The WAPs support wireless bridging and repeater mode.
If you already have a WRT54GL then you have to install a 3rd party firmware which adds wireless bridging capabilities. Read the wikipedia article on "WRT54G" for information about which WRT models support 3rd party firmware and an overview of projects and links.
Remember, however, that you may brick your router if you install a 3rd party firmware incorrectly and you probably void the warranty if you install 3rd party firmware (it is even possible to find out after you restore the original Linksys firmware if you don't clear the NVRAM before).
Maybe you are looking for
-
Solution Manager Installation Fails at step Run ABAP Reports
I'm trying to install Solution Manager 4.0 on Windows 2003 using SQL 2005. The installation fails at the Run ABAP Reports step: Executing ABAP report RADDBDIF I have logged in manually and run the RADDBDIF job in SE38 but I receive the same error me
-
JMS Exception - unable to connect to the JMS destination
Hi, I've configured WebLogic10R3 Cluster with one Admin Server and 2 Managed Servers. I deployed the application to the Cluster. (Ie. both Managed 1 and Managed Server 2.) I am geeting the following JMS destination not found exception while starting
-
Error in reading data from InfoSet
Hi Experts, I am facing the below errros when doing a selection to retraive data. @5C\QError@ Error when reading data from InfoSet Z40_2 (return code 1) @5F\QNo long text exists@ 17:56:24 A Preparatory Steps 1 Selection and
-
I cant open safari on my macbook pro, pls help me!!
Safari in my macbook pro get stuck cant opned it. pls help me some clues to solve it.
-
We would like to configure RADIUS fallback to ensure RADIUS authentications always go to their primary ACS while it's available, but the documentation is not very clear with regard to the username configuration. There is no mention of a password, but