I need help in frequency readings‏

Hi,
goodafternoon,
By using the attached file i wanted to read the frequency of the signal " the signal is pulses"
i have done it and record the reading in excel files
if u check the excel files u will find high values but on the oscilloscope the value for file frequency100 and frequncy101 should be between 430hz to 460hz but in the file it is very high .
can i know what is the problem please ?
i am using cDAQ-9188 with digital input 9401
i connected the signal to pin#14 and the com to the ground of the driver
Note i have emailed 2 emails before this email and there is no reply since last week, any one can help me in that ?
thanks
Attachments:
i need help in frequency readings.zip ‏276 KB

You're probably picking up noise.
Try adding digital filtering to your application (see here). You will have to use the lower-level DAQmx API instead of the DAQ Assistant.
Best Regards,
John Passiak

Similar Messages

Need help on which router to buy for my BB 8320

Now i know 8320 is dated but at this point i am not planning to change anytime soon .
So I have a router which is kinda old, it didnt really occur to me since it worked. When i got my bb 8320 i was in a hotel and i could connect through their wireless without any hassle. I could surf, use youtube, name it.
When i got home i couldnt do anything, i spent countless nights trying to figure out waht was wrong then i realized its my router. If only BB said somethign it wont support old routers then i wouldve saved myself hours of self-loathing.
Anyways I also have gone to my friends house, and i could connect to her linksys router without any hassle. i was the one who set her router up and we bought it this year. i didnt do anything special, configuration-wise or w/e.
So NOW i am just going to buy a new router. I really need help!!!!
I was wondering if this one is good:
W311R Wireless-N Broadband Router
W311R integrates the wireless AP, router, four-port switch and firewall in one, and increases over 4 times transmission range of ordinary 802.11g products. Compatible with IEEE802.11n (Draft 2.0) and IEEE802.11g/b standards, it can provide up to 150Mbps stable transmission rate. It is dedicated to SOHOs and students’ dormitory. In addition, URL and MAC address filtering can take it easy for parents and network administrator to manage network life, and QoS bandwidth control over specific computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet.
Overview:
* Includes router, wireless access point, four-port switch and firewall in one
* Provides up to 150Mbps uploading and downloading speed
* Supports two WPS (Wi-Fi Protected Setup) encryption methods: PBC and PIN
* Compliant to IEEE802.11n, IEEE802.11g, IEEE802.11b, IEEE802.3 and IEEE802.3u standards
* Supports far-distance transmission, 100 meters indoor, 400 meters outdoor (depends on the environments around)
* Supports 64/128-bit WEP encryption, WPA and the latest WPA2 encryption security authentication
* Supports RTS/CTS protocol and data partitioning function
* Provides one 10/100Mbps Auto-Negotiation Ethernet WAN ports for WAN connection
* Provides four 10/100Mbps Auto-Negotiation Ethernet LAN ports for LAN connections
* Supports xDSL/Cable MODEM, static and dynamic IP in community networking
* Supports remote/local Web management
* Supports WMM to better smooth your voice and video
* Supports SSID stealth mode and access control based over MAC address (up to 30 entries)
* Supports Auto MDI/MDIX
* Supports wireless Roaming technology and ensures high-efficient wireless connections
* Supports auto negotiation/manual mode for 802.11b/802.11g/802.11n
* Supports UPnP and DDNS
* Supports Firefox 1.0, IE5.5 or above
* Supports SNTP
* Supports virtual server, DMZ host
* Built-in firewall for hacker’s attack prevention
* Supports DHCP server/client
* Supports auto wireless channel selection
* Supports the control over LAN access to Internet
* Provides syslog to record the status of the router
* Supports WDS wireless network extension
* Supports QoS function
Input Voltage Range
AC 110~240V
Output Voltage Range
9V~1000mA
Consumption
20dbm
Operating Temperature
0? ~ 40?
Storage Temperature
-40? ~ 70?
Operating Humidity
10% ~ 90% RH non-condensing
Storage Humidity
5% ~ 90% RH non-condensing
Antenna
One Non-detachable external antenna (5dBi)
Frequency Range
2.4GHz-2.5GHz
EVM
-30dB
Sensitivity
54M:-74dBm@10% PER; 11M:-85dBm@8% PER; 6M:-88dBm@10% PER; 1M:-90dBm@8% PER
Outdoor
400m
Indoor
100m
WLAN?LAN
93Mbps
WLAN?WLAN
93Mbps
Frequency Range
2.4GHz
Gain
5dBi
Nominal Impedance
50
Polarization
Linear; Vertical
Maximum Power
1W
* Vertical Beamwidth 360º

Flip UltraHD.
Shoots mp4 H264 format files. Fits in a shirt pocket and records 2 hrs worth of material to an internal card. Charges from your USB port as you download. If you are just trimming clips, you can use QT Pro without conversion. If you need to edit, convert to ProRes 720p30. Works like a dream.
Just make sure you have it solidly placed when you pull the trigger as there is no image stabilization.
Oh, and it is only $199 US.
x

Need help with overclocking my x58 pro-e

hi i have this new mb from msi and i need help fixing stability issues :
ok here i go i did the normal oc to 3.1 that needed nothing voltage wise so now i need to go pro ^^ so plz help me out and 1 more thing if u know any thing about ssd and ide mode or there is any thing better plz help me out :>
ok i tried oc it to 4.2 it runs fine tell it hangs some times and freezes or even do some restarts on its own the usual i mean for a fail oc :P if u could help me out setting up my oc in a pro way i would love u for ever ^^
specs r writing down under ^^

OK i m back guys and sorry i took so long i tried some new O.C and i got so far as 3.7 on my cpu i saw that i had like really bad heat on the cpu on OCCT/prime and other testing programs i easily got to 95+ witch i stoop not wanting to know where it will hit :P
then i opened my pc yanked the motherboard out removed the cooler and the IOH cooler cleaned them both up reapplied the Thermal Grease witch came with my Thermaltake ISGC-400 and for extra cooling i add a sec fan on top of the cooler fan (yes it made some extra noise but it works :P ) rebuild it and tried again and the result was :
ideal temp: 60+ / load temp: 95+ / IOH temp: 85-95+ // and now :
SAME !!!! but the IOH dropped like a charm to 55 maybe 65 max .
so i know it was time to google some webpages and i saw some photos of CPU-Z all showing low core voltage and by low i mean the standard core i7 920 voltages ! mine was given by the auto bios setting so i continued searching tell i found out the higher the V.core is the high hte numbers are on the sensors !
i found out that a standard voltage will take me to 4GHz of speed so i tried it on my 3.7 (current speed )
and the result was lets just say WOW ! i think :
ideal temp 38+ / load temp: 83 (prime95) / IOH temp : 55-60 (after the cleaning / rergreasing)
so i tried it with my game (wow) and it never raise more than 65 max ! so if i over clocked it to 4K i dont think i will ever overheat it never the less i have a temp montering it with a max 85 on the alarm .
so far my tests and errors :
Multiplier= x21
bus speed = 177
voltages:
QPI: 1.30
CPU V.core : 1.28ish i cant realy tell from the bios
CPU PLL: 1.82ish same thing
speedstep=off/turbo=off/C1E=off/execute = off /over speed protection=off /V.tech=off/HPET=on(so numbers wont play much on cpu-z)
now for ram :
3x6 ratio ( in bios in windows it shows 2:6 for some reason ) DRAM frequency is showing 531 Mhz
9.9.24.88
V=1.5
any thing above these settings will crash the pc/not booting at all and i feel its not a stable system now ether so tell me what im doing wrong here please since there was a post just about like me in this forum but the man who made it never got back to you :> ty and realy sorry for the long post ^^

Need Help with setting up this Filter

Hi,
I need help making a filter sound like the one used in this youtube song.
I tried setting it up but I've had no success; even though I know for a fact that this filter was made in Logic Pro 9 according to the maker of this song.
I think there might be a bit of 'Fuzz-Wah' in there too but I've never really used that effect so any tips on that would be great, too.
Link: http://www.youtube.com/watch?v=tf017M8SZZE&feature=plcp
Any help with this would be widely appreciated.
Thank you :-)

It sounds like a simple hi Q filter sweep to me but getting close to the original synth sound that it is being used on is the challenge. It might well be that it is the filter on the synth itself is what is being swept. Either way, turn up the filter resonance on a band pass filter and sweep it with the lfo or adsr to modulate the filter cutoff if its the synth filter, or automate the filter frequency sweep if you use the channel filter.

How can I output frequency readings of my signals using FFT?

Hi there, I need help in regard to the topic stated.
Currently I have accquired a sine wave with frequency that vary, using one of the accquistion card by NI. I had converted it to a digital signal so that labview can read it. Now, I will like labview to output the measurement of the frequency.
For example : sine wave of 5KHZ is accquire , labview will use FFT to convert time domain to frequency domain, and then output the frequency of the sine wave, in the case, 5KHZ.
What function block should I be using? I had explored the function blocks of all FFT. Most of them output either real FFT, complex FFT, magniture or phase. But none of them output the reading of the frequency.
Maybe I had missed out some function block, so how do I go about output a frequency reading after using FFT?
Thanks a lot in advance.

After Converting your signal from time domain to frequency domain, u cant expect there is only one frequency component,they should have different frequency components according to your input signal.Use extract single tone information to get the output reading of the frequency.
Balaji PK (CLA)
Ever tried. Ever failed. No matter. Try again. Fail again. Fail better
Don't forget Kudos for Good Answers, and Mark a solution if your problem is solved.
Attachments:
Detect Freq.vi ‏15 KB

WRT54GS cannot be configured, need help!!!!

Ok.. I am getting so lost. I will try to explain the best I can what is going on. I just bought the Wireless G router with speedbooster and put the CD in to set it up, did everything it told me to do on the screen as far as pluggin cables in yada yada. When it came to step 4 of 4 it said "Waiting for Router". Then after about 2-3 minutes it comes back saying the following:
YOUR ROUTER DOES NOT APPEAR TO BE CONNECTED PROPERLY
Error 322: New router or Gateway not detected
Follow these steps:
1) Make sure you are connecting your new router and not your old router
2) Make sure the ethernet cable from your computer is securely connected to a LAN port on the back of your new router
3) Click retry to try installing your router again
Also, when I try to retry the setup without unplugging anything it says this:
Linksys EasyLink Advisor Setup Wizard has discovered that you are already connected to a router. Many people choose to replace an existing router with their new Linksys Router.
I can connect to the internet without configuring the router!!! It isn't secure though! I want to configure my router so that it is secure and I don't know what to do to fix this.
I am using a Comcast provided modem, RCA model # DCM425
Any help would be greatly appreciated... Remember I am a noob so please don't confuse me more with words I don't understand.. Thanks
One more thing. When it is "Waiting for router" the 2 computer icon comes up at bottom of screen saying acquiring IP address so I double clicked on it and it would be connected with the IP address 192.168.1.1 and then all of a sudden it would say Invalid IP address not connected. I really need help here!!!

Ok, I'm not 100% sure I can help you, but I will try.
First thing, find the setup disk that came with the router and use it as a coaster or a frisbee or something because it is almost completely worthless.
Until you have completed the setup of the router, I would suggest using a computer that is connected directly to the router via ethernet cable. The reason being, if you change any settings wirelessly, such as security features, you will be disconnected and unable to access it again. So use a computer that is directly connected for setup.
The IP address you saw in you system tray is the IP address of the router itself. You actually need this for your router setup. Open whichever web browser you use and type in that IP address, nothing else. 192.168.1.1 A login screen should appear for you to enter your user name and password. Leave the user name blank and for the password enter "admin" without the quotes. This should bring you to your basic settings screen for the router.
From this point, I'm sure exactly how you want to set everything up. If you're not very familiar with networking or routers I would suggest you change very little. If you desire security for your network (which I suggest) click on the "Wireless" tab at the top of the screen. This should bring you to basic wireless settings. From here, you can change the name of your wireless network, change the broadcast frequency and enable/disable wireless broadcast. You can change these if you like or leave them alone whichever you prefer. I do suggest changing the name of you network (SSID) so you can tell which one is yours when you try to connect. It gets confusing when everyone in your neighborhood has a Linksys and all of the names look similar.
Once you're done here, next click on the "Wireless Security" tab within the "Wireless" tap. Make sure you are click "Wireless Security" and not just "Security." From here, you can select the kind of wireless security you want to use. I'm not highly informed on which of these is the best, but WEP is probably the strongest security you're going to need anyway, so I would go with that. After you select WEP you get a few more options. For "default transmit key" just select one. Then in the "WEP Encryption" drop down, select "128 bits 26 hex digits." 64 would most likely be ok, but 128 bit encryption is definitely better.
In the next box "Passphase" enter a word or short phrase that is only known to you an click generate. The four boxes below will now have you WEP keys. I delete all but the first key to keep things simple, but whatever you want to do is up to you. After you delete the other three lines, select the key in your first line and select/copy it so that you can just paste it into the box in network options when you're connecting to the network. Regardless, I would also write this key down somewhere. If you have multiple computers in the house you have to enter it on each and every one and it's a pain to go back and forth. Click save settings. You're pretty much done. There are other things you can do to beef up security, but this is the most basic and it's still quite strong.
If you are looking at playing games frequently or anything like that I would go to PortForward.com
Any other questions you have, you should be able to google I think. I hope I can help. Good Luck.

Need help bad, screen problem

heres my problem. i setup arch on my desktop last night (64bit), i installed my nvidia drivers. i have a 21" crt sun monitor, not sure the model number. but i brought it to a friends this morning to update and install kdemod since they have highspeed. now i was hooked up to their monitor, they have a cheap 15" crt. so it worked fine there, now when i got it home, i get a black screen when it boots up on my monitor, i can get to a console however
i deleted a couple lines in the monitor section in the xorg.conf............so now i get 640x480 res, but i cant use anything higher
been searching around, and i found some stuff about running Xorg -configure, but i get something about a tmp file being locked..........and i dont know how to delete anything here from the console
i need help here
Last edited by ssl6 (2007-09-16 07:00:40)

nvm, i just deleted the xorg.conf and rebooted, its fine now
edit// nvm, its not using my nvidia driver.........i might still need help, im trying something right now, not sure what im doing though
ok, i tried to run nvidia-xconfig, and when i rebooted, im back to square one with my monitor flashin an invalid scan frequency
well, i deleted the xorg.conf again and got it booted up. but i generated a new one with nvidia-xconfig again, heres what i puts out, i just need to remember not to reboot any time soon. im using a 7900gs, the newest nvidia 100 series drive from the repo, and arch 64bit on this system by the way
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder26) Wed Jun 13 16:54:14 PDT 2007
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
RgbPath "/usr/lib/X11/rgb"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "type1"
Load "freetype"
Load "glx"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 30.0 - 110.0
VertRefresh 50.0 - 150.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1600x1200" "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
here's that part of the xorg.conf from my other computer running 32bit arch with a geforce 3 connected to the same monitor via kvm switch. this machine is using a 96xx driver though
Section "Monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
Identifier "sun"
HorizSync 31.5 - 82.0
VertRefresh 50.0 - 90.0
EndSection
Section "Device"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
Identifier "Standard VGA"
Driver "vga"
VendorName "Unknown"
BoardName "Unknown"
EndSection
Section "Device"
#VideoRam 65536
# Insert Clocks lines here if appropriate
Identifier "geforce"
Driver "nvidia"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "geforce"
Monitor "sun"
DefaultDepth 24
Option "AddARGBGLXVisuals" "True"
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
any ideas here?
Last edited by ssl6 (2007-09-16 07:53:48)

Need help with clickbios ii terminolgy and values. Z77A-GD65 / 3770k

Hello All
I recently purchased a Z77A-GD65 board and after searching I've found the differences in terminology between this and my previous Asus board but still have a couple of settings I cant find any info on.
System Specs:
motherboard: msi z77a-gd65
cpu: intel 3770k
ram: corsair vengeance 2133mhz 1.5v
psu: corsair 850w
First things first is I believe I am running in turbo oc mode. I've selected the oc genie tab on the center right of the bios screen and proceeded to change settings there. With cpu voltage on auto and vdroop set to 50% at 4.6ghz. (I'll try and get screenshots of bios settings soon)
The following are the terms I need help with:
In the my oc genie section;
1. Long duration power limit
2. Long duration maintained
3. Short duration power limit
In the main overclocking section;
4. Digital Compensation level (not in owners manual, options auto/high)
5. Cpu core ocp expander (enabled for overclock 4.5ghz+?)
In the CPU Features section;
6. long duration power limit w (does "w" stand for watts?)
7. long duration maintained s (does "s" stand for seconds?)
8. short duration power limit
9. primary plane current limit a (does "a" stand for amps?)
10. secondary plane current limit
11. primary plane turbo power limit
12. secondary plane turbo power
I know those are a lot of settings, but would appreciate any simple definitions as to what they do and recommended values for mild overclocking (4.5-4.80)
Also on my previous board (Asus P8P67 Pro) my 3770k was stable in prime95 for 18 hrs at 4.5ghz fixed 1.155v with only ram timings put in manually and LLC set to extreme.(or whatever max is called in asus bios) Voltage was fixed and everything else was defailts.

Well I'm back. Been digging around for a few days and found some answers to my questions.
First things first s that for some reason I could not adjust voltage values with the + or - symbols. Clearing cmos did not help this. I had to reflash the bios to get this functionality back as well as clearing cmos before and after the flash.
So I figured out the values in the oc genie section are the same as the normal section but only used when your using the oc genie. (numbers 1-3)
Digital compensation level and ocp expander should be set to high and enabled respectively when going for higher overclocks. (4 and 5)
Now for the rest of my questions ( 6 through 12) I have found suggested settings and some info after hours and hours of searching but still have a couple of questions about them.
Long/short duration power limit, and primary/secondary plane turbo limit. I see suggestion settings of 250 or 255. I take it this is simply max supplied watts to the chip? If so why the 250/255 values? Is that the highest the board will give? Is plane turbo limit related to the enhanced turbo stated and how much wattage can be drawn there while the other limit is for any non turbo frequencies?
Long duration maintained, I've seen 60 suggested a lot. Why is this?
There's not an over abundance of info on these boards as compared to asus so it seems info is a little less documented and video tutorials explaining things are next to none.
Any help would be appreciated. Thanks

Need help to develop Pythagoras theorem-

Hi i need help to develop proofs 2,3,4
of pythagoras theorems in java as demonstrations
These are applets can anyone help me with it or give me an idea of how to go about developing it -
the site is the following
http://www.uni-koeln.de/ew-fak/Mathe/Projekte/VisuPro/pythagoras/pythagoras.html
then double click on the screen to make it start

Pardon my ASCII art, but I've always liked the following, simple, geometric proof:
     a                   b
---------------------------------------+
|       |                                |
a|   I   |              II                |
|       |                                |
---------------------------------------+
|       |                                |
|       |                                |
|       |                                |
|       |                                |
|       |                                |
b| IV   |              III               |
|       |                                |
|       |                                |
|       |                                |
|       |                                |
|       |                                |
|       |                                |
---------------------------------------+It almost goes without saying that I+II+III+IV == (a+b)^2, and II == IV == a*b,
I == a*a and III == b*b, showing that (a+b)^2 == a^2+a*b+a*b+b^2.
I hope the following sketch makes sense, stand back, ASCII art alert again:     a                   b
---------------------------------------+
|               .             VI         |
|     .                 .                |a
| V                               .      |
|                                        +
|                                        |
|   .                                    |
b|                                     . |
|                                        |
|                  IX                    |
| .                                      |
|                                    .   |b
|                                        |
+                                        |
|      .                                 |
a|               .                  . VII |
| VIII                   .              |
---------------------------------------+
                 a                    bThe total area equals (a+b)^2 again and equals the sum of the smaller areas:
(a+b)^2 == V+VI+VII+VIII+IX. Let area IX be c^2 for whatever c may be.
V+VII == VI+VIII == a*b, so a^2+b^2+2*ab= c^2+2*a*b; IOW a^2+b^2 == c^2
Given this fundamental result, the others can easily be derived from this one,
or did I answer a question you didn't ask?
kind regards,
Jos

I need help to find and open a job app that I exported, was able to fill out and sign and saved and now can't open it? What did I do wrong?

I need help to find and open a job app that I exported, was able to fill out and sign and saved and now can't open it? What did I do wrong?

What file format did you export it to?

Need help to open audios attached in a PDF file

Hello
I just need help. I have ordered a reviewer online that has audios and texts in a pdf file. I was told to download the latest adobe reader on my computer. I have done the same thing on my ipad mini. I am not so technical with regards to these things. Therefore I need help. I can access the audios on my computer but not on my ipad.
I want to listen to audios with scripts or texts on them so i can listen to them when i am on the go. I was also informed that these files should work in any device. How come the audios doesnt work on my ipad.
Please help me on what to do.
Thanks

Audio and video are not currently support on Adobe Reader. :-<
You need to buy a PDF reader that supports them. My suggestion is PDF Expert from Readdle ($US 9.99)

Need help to open and look for file by name

Hi,
Im needing help to open a folder and look for a file (.txt) on this directory by his name ... The user ll type the partial name of file , and i need look for this file on the folder , and delete it ....
How can i look for the file by his name ?
Thx =)

Hi ,
Sry ,, let me explain again ... I ll set the name of the files in the follow order ... Name_Serial_date_chanel.sxc ..
The user ll type the serial that he wants delete ...
I already figured out what i need guys .. thx for the help ^^
I used List Directory on advanced IO , to list all .. the Name is the same for all ... then i used Name_ concateneted with Serial(typed)* .. this command serial* ll list all serials equal the typed , in my case , ll exist only one , cuz its a count this serial .Then i pass the path to the delete , and its done !
Thx ^^

I need help, my ipod touch is not recognized by windows as a harddisk

i need help, my ipod touch is not recognized by windows like a memory card or a harddisk.
i would like to transfer the files from pc to my ipod touch without useing itunes.
as i see theres some people here that theires ipod touch are recongnzed as a digitl camra, mine is reconzied as nothing, some help plz.
Message was edited by: B0Om

B0Om wrote:
ok but i still dont understed, only my itnes recongnize my ipod, when i go to " my cumputer, it dosent show up there, not even as a digital camra
Your Touch is working correctly. Currently, without unsupported third party hacks, the Touch has NO disc mode. It will only show up in iTunes.
how do i put programes and games in my ipod touch
Right now, you don't. The SDK is scheduled to be released in Feburary. Then developers will be able to write programs that will be loadable.

Weird error message need help..

SO.. i havent updated my itunes in a while because i keep getting this weird message.. it comes up when im almost done installing the newest/newer versions of itunes. it says
"the feature you are trying to use is on a network resource that is unavailable" "click ok to try again or enter an alternate path to a folder containing the installation package 'iTunes.msi' in the box below"
now when ever i choose a file from the browse box it replies with this message "the file 'xxx' is not a valid installation package for the product iTunes. try to find the installation package iTunes.msi in a folder from which you can install iTunes."
no idea need help thanks
~~~lake
Message was edited by: DarkxFlamexCaster
Message was edited by: DarkxFlamexCaster

+it comes up when im almost done installing the newest/newer versions of itunes. it says+ +"the feature you are trying to use is on a network resource that is unavailable" "click ok to try again or enter an alternate path to a folder containing the installation package 'iTunes.msi' in the box below"+
With that one, let's try the following procedure.
First, head into your Add/Remove programs and uninstall your QuickTime. If it goes, good. If it doesn't, we'll just attend to it when we attend to iTunes.
Next, download and install the Windows Installer CleanUp utility:
Description of the Windows Installer CleanUp Utility
Now launch Windows Installer CleanUp ("Start > All Programs > Windows Install Clean Up"), find any iTunes and/or QuickTime entries in the list of programs in CleanUp, select those entries, and click “remove”.
Next, we'll manually remove any leftover iTunes or QuickTime program files:
(1) Open Local Disk (C:) in Computer or whichever disk programs are installed on.
(2) Open the Program Files folder.
(3) Right-click the iTunes folder and select Delete and choose Yes when asked to confirm the deletion.
(4) Right-click the QuickTime folder and select Delete and choose Yes when asked to confirm the deletion. (Note: This folder may have already been deleted if QuickTime was successfully removed using Add/Remove Programs earlier.)
(5) Delete the QuickTime and QuicktimeVR files located in the C:\Windows\system32\ folder. Click Continue if Windows needs confirmation or permission to continue. (Note: These files may have already been deleted if QuickTime was successfully removed using Add/Remove Programs earlier.)
(6) Right-click on the Recycle Bin and on the shortcut menu, click Empty Recycle Bin.
(7) Restart your computer.
Now try another iTunes install. Does it go through properly now?

I got new hard driver for my MacBook I don't have the cd but I do have flash drive that has the software I need help because when I turn on my laptop it shows me a file with question mark how can I install the software from the flash driver?

I got new hard driver for my MacBook I don't have the cd but I do have flash drive that has the software I need help because when I turn on my laptop it shows me a file with question mark how can I install the software from the flash driver?

Hold down the Option key while you boot your Mac. Then, it should show you a selection of devices. Click your flash drive and it will boot from that.

I need help in frequency readings‏

Similar Messages

Maybe you are looking for