I need help in msi enjoy 7 plus tablet

Hi everybody i need to unscrew the back of the tablet msi enjoy 7 plus to fix a problem in the speakers but obvious there is no nails in it. could anybody help me.      
thanks in advance

Enjoy 7 Plus is not meant to be opened by users. Contact MSI support for repairs as it should still be covered by warranty: >>How to contact MSI.<<

Similar Messages

  • MOVED: Need help with msi mega 180 + athlon xp-m combo

    This topic has been moved to Overclockers & Modding Corner.
    Need help with msi mega 180 + athlon xp-m combo

    AFAIK, you shouldn't need a pinmod for a Mobile Athlon XP CPU to work in a nforce2 mobo
    did you have any other CPU installed prior to this one? if so, refer here to clear the CMOS: Clear CMOS Guide
    next, refer to your manual, or download from MSI, for location of the FSB jumpers; ensure J8 is shorted across pins 1-2, and J7 is shorted
    finally, enter your BIOS setup menu, and under Advanced Chipset Features, set CPU FSB to 133mhz (or even 166mhz if you have DDR333 memory). the only thing i can't see in the Mega 180 manual is where you set the multiplier...
    which is where the BIOS has limited overclocking features, and you might have a problem here
    i think i'll pass this over to the Overclockers forum, where someone may be able to give a better answer....

  • MSI ENJOY 10 PLUS, Media USB not Detected in CPU (HELP)

    winpad enjoy 10 plus I can not be touched, do not work, and the device is not detected on the computer (no media), so can not upgrade the firmware again, the power button (Android system recovery utility v1.3.38) not work, though already updated drivers, follow instructions, the result was like that, please provide a solution, 

    Try to use another cable to see if the problem comes from the cable.
    Also, you can try to insert the straighten paperclip to the reset hole and plug the AC adapter to power on the tablet again.

  • NEED HELP..MSI {6712} KT4v-L bios 1.9

    First i need help flashing my bios i have 1.8 now
    and want 1.9. I am useing xp pro fully updated on an ntsf file format i have no floppy never needed i have a usb 64meg thumb drive . I do not overclock ever ....
    I have read several places how to do this but all are a little different so i decided to ask the real pro you guys.
    would some one give me a full very detailed description on how i can do this preferbally soemone who has run into the same situation i have any help would be much appreciated.
    MSI KT4V-L {6712}
    AMD 2400+ {266}
    PNY 256 DDR {333}
    PNY 5200 DDR FX 128
    Creative Audigy 2 Platinum
    Sony 16X DVD
    Sony DVD-+RW-+
    Creative Labs MegaWorks THX 6.1 600 watts
    Antec Lanboy
    Antec 300 True Power
    Thermaltake 3 speed intake
    Thermaltake 3 speed exhaust

    i had exactly the same problem  - na floppy ever needed
    1. burn a cd with ami flash or other flash program and your bios file
    2. boot the system with your ( in my case windows 98 se ) cd
    3. choose to boot with cd-rom
    4. run amiflash from your burned cd
    5. enjoy !!

  • Really need help with MSI R7970-2PMD3GD5/OC:(

    Greetings to all,
    I really need help with my brand new MSI R7970-2PMD3GD5/OC. I've purchased it two days ago and I didn't really have time to test the card until yesterday. The card is I think way to hot for my "liking". It idles at 56c-60c, at full load in Heaven benchmark 3.0 in 1920x1080, extreme tessellation and 8xAA card reaches 95c-97c. Stock cloacks are 1010Mhz/1375Mhz and stock voltage is 1,174v. Case is being cooled by two Noctua NF-P12 fans. Also I tried lowering the voltage and "underclocking" the card to a standard 925Mhz in small increments, but it doesn't help at all. Each and every time it results in BSOD and dx dll errors and complete system failures. Replacing the card wouldn't be a problem if I lived in a "normal" country that has access to a steady supply. Retailer that sold me a card told me that only 5 cards total have been imported from the launch day and told me that i bought the "last" card in my country. They could order a replacement but it would take them more then a month to do so.:( Ohhh and one more thing I don't overclock, everything in my case is at their default values.
    Recently, I read that "Amd released" a bios update for a standard reference boards that turns them into a "GHZ editions". Also lot of users report a lower voltage requirements and lower temps with that "boost bios". As I understand this card pcb is not Amd's reference board design, I could be wrong it's not that uncommon.. So I didn't want to risk warranty by flashing it to a position 1. Will MSI release the boost bios for this model of card? I am humbly asking MSI staff on how to proceed regarding this problem. I would be immensely grateful for any help you could provide.

    Quote from: Svet on 24-August-12, 18:13:26
    what PC case you use exactly?
    have you tried to open PC case side door and to retest?
    Hi,
    it's open case. If i close it the temps get even worse:(
    They get better for other components, but not for gpu. Two Noctua NF-P12's are cooling the case, first one is positioned above gpu, left side next to cpu. Other is right beneath the gpu, right side of case. Just under the hdd section of the case. I tested each and every component with my backup card nv 8500gt. They function within the specified parameters. I'm getting somewhat worried.
    П.С. Поздрав Свет
    да ли сте ви са наших простора да не куцам на енглеском?

  • NEED HELP ON MSI 6380 KT266

    Please, I Need help.....
    first of all, at night, my System seems ok when i print a picture. then the problem came at the morning, when the PC wont even turning on! after some time, about 1-3 minutes, the PC turned on on itself!!! sometimes the PC rebooting it self when the LED indicating the RAM, and the Processor scanned....then i came to the result that the PS was damage, it was 300W PS
    then i bought a new 350W PS, and i plugged all, and it seems it isn't solving the problem...but when I move the RAM from bank 1 to bank 2, the system seems more stable....then i have a conclusion that it was the RAM, so i brought the PC to the MSI distributor on my Country ( Indonesia ).
    after a while, they doesn't want to replace the RAM / Motherboard ( the Mobo is for 2 years warranty, and they distribute the RAM, Apacer,  too ), because they said it was the PS, so they returned it to me....
    so, I ask my friend about the PS, and he said that if the +5V below 4.9V then i was the PS, and it's true, it is @ 4,810v - 4.893v on the BIOS....but how this is connected to the RAM bank 1? i have a 25A for +5v at my PS. until now, the only thing i've done is to reduce the FSB to 100, and moving the RAM to Bank 2. but it's still unstable for sometime.....
    *ADDITION* and when finally the PC succeed on Windows, suddenly, i hear a sound, similar to when
    you turn the system off..."clack" ...when it does, the PC hang, and after a few seconds...it reboot itself
    Do you guys here, experts, could help my on my problem? how to increase the +5v? please, help me....i'm so desperate....
    this is my spec :
    MSI 6380 KT266 Pro
    Athlon TBird 1,33 Ghz @ 1 Ghz   ;(
    ThermalTake V7+
    Arctic Silver 3
    40 Gb Quantum
    PowerColor GeForce 2MX 200
    Apacer 256 PC 2100
    Nippon Power Supply 350 W

    @ Idle : 45
    @ Full Load : 48
    there are no combination @ my PSU but these are written on the label :
    DC Max OUTPUT 350W+
    Voltage
    230V
    Red +5V, 25A --> it's only 25A, isn't it too low?
    orange +3.3V, 28A
    Yellow +12v, 12A
    White -5v, 0,5A
    Blue -12V, 0.5A
    Puple 5vsb, 2.0A
    Gray P/G, OK
    and um...what should I do next, wonkanoby?
    and..nope...I'm not that noob on CPU thing....and I've use the AS3 about 3-4 months...i spill AS3 on the die at least the same size as a rice ( sorry for the bad english ) :D

  • Need help with MSI P45 Neo3-FR

    I haven't been here in a long time. My old board (just replacing it) worked perfectly for almost 4 years after I ironed out the kinks (MSI 865p Neo2-FISR) but I finally decided to upgrade my rig, but here comes the headaches...
    I bought the following for my new setup:
    MSI P45 Neo3-FR (came with BIOS 1.3 installed)
    2GB (2x1) Corsair Dominator 6400C4D
    MSI Radeon HD 4850
    Intel Pentium Dual Core E2180 (I want to overclock it hehe)
    Lite-On SATA CD/DVD-RW
    Old Hardware being used:
    Antec TruPower 550W EPS12 (single rail 36amps on +12)
    Cooler Master Centurion (forgot what model) Case
    Logitech USB Keyboard
    Logitech MX518 USB Mouse
    2x120mm fans
    2xMaxtor SATA 80GB HDDs (note: NOT SATA II, and I want to run these in RAID 0 off the ICH10R, this is specifically why I bought this board I was going to go with the P43-Neo3 over this, but the inclusion of RAID sold me on it)
    1xMaxtor SATA 160GB HDD (note: NOT SATA II)
    Aside some trouble I had with the Intel HSF installation was a breeze. Everything is in. I wanted to run everything stock first. Jumped into the BIOS and set the following:
    SATA Controller - RAID
    DRAM Voltage - 2.1v
    Drive Layout:
    SATA1 - 80GB Maxtor
    SATA2- 80GB Maxtor
    SATA7 - Optical Drive
    SATA8 - 160GB Maxtor
    First power on to get into the BIOS was quick. After setting SATA to RAID, POST will hang at Auto-Detecting ACHI Port 1....then find HDD after about 20-30 seconds. And it will repeat itself for Port 2. So its taking me close to a minute (I might be exagerrating but it sure isn't quick and long enough to irritate me having to keep booting) just to POST and even access the BIOS.
    Tried to use my current Windows XP install, got to the Windows XP Splash screen and it rebooted. Tried again, with super long ass POST, again rebooted at the splash screen. Said, fine I'll reinstall XP.
    While browsing here I forgot where I read about the SATA and long posts, so I changed my 2x80GBs to SATA3 and SATA4, it no longer takes a minute to POST, goes quick as normal.
    Set Optical to boot, go into the Windows XP Install screen, F6 for custom drivers, made a RAID disc using three sources (1. RAID drivers from MSI Website, 2. RAID drivers from MSI CD included with Motherboard, 3. RAID Drivers from Intel website) and each time at a certain point I'd get a BSOD.
    Tried again by moving my last HDD/Optical to the ICH10 and disabled the Jmicron. Same, BSOD.
    Switched off RAID in the BIOS and set it to IDE. AGain BSOD at XP Install.
    Started to think it was a Memory issue, ran Memtest both sticks passed.
    One thing I noticed in the BIOS, it has my RAM clocked at 1066. Everything is on auto minus the voltage, but I didn't think it would affect it. So I changed the Ratio from auto to 1:2 (800mhz CPU:800mhz DRAM) but still BSOD everytime I try to install Windows.
    This is getting frustrating. I've run out of ideas. Any help would be greatly appreciated.

    Quote from: BOSSKILLER on 02-August-08, 22:07:06
    Read here how to do it:
    >>> Slipstreaming Windows XP Service Pack 2 and Create Bootable CD<<<
    >>> Slipstreamed Windows XP CD Using SP2<<<
    Other option is borrow such installation disk from friends.
    I moved away from my "friends" and none PC literate, so I'd be better off driving to the store and buying Vista at this point. Haha.
    Okay, going to try this...sounds like that project I started a whiles back but got lazy.
    Thanks guys, I'll report any results.

  • Need help with using Zen V Plus in a

    I have a Zen V plus 2GB and I'd like to use it in my car with a FM transmitter/charger combination. The one I bought says it works with Creative zen MP3 players, but will not charge the player even though it has a USB with 5 VDC as output. It does play the player through the FM reciever just fine. I also noticed that I can only charge the player through the very same USB port on my computer where I first connected it when I was setting it up. Any other of the USB ports will not charge the player. Does this have something to do with this problem?

    Hello al9spike,
    Welcome to Creative forums!
    I'm not sure when you said "reset and play while plugged in" is the same as resetting the device by inserting a paper clip in the reset hole while plugged in. If not, then you can try this. There is a also a similar thread here with the same problem your experiencing right now. Maybe this could help you. Otherwise, if the unit is still not turning on, I suggest you contact support for further assistance.
    Best of luck,

  • Need Help w/ HP DesignJet 750C Plus

    I just acquired this plotter from a friend & can not get it to plot or get it setup correctly.
    I'm trying to plot to it directly from my PowerBook but I don't know how to do it. The plotter has a built-in JetDirect card w/ a RJ45 socket plus it also came with a separate HP JetDirect 300X box. I have tried connecting through both but still can't see it in the Fax/Print setup window.
    I downloaded the latest 750C driver from HP but still no luck.
    Anyone know what I can do to connect properly?
    Thanks for any help!

    tony I hate to be the barer of bad news but you and i are in the same boat... The only difference is i've been throwing money at it longer. I too bought a used 750c plus from a friend last fall. I've been fighting with it for months! in short... it's not compatible with os10+ i can't get mine to print any thing over 1.2 megs and thats by tricking it to use the 755 driver. HP is is totally unhelpfull as they no longer offer any support for these old timers. I finally thought I had the answer when I stumbled accross xrip software. http://www.macroenter.com/MicrospotXRIP_Educationalp/mxrs15ed.htm but since i spent the 200.00 i've been in constant contact with microspot in europe trying to figure out why the prints look so horrid. to their credit they seem to be genuanly concerned and are helping me try to fix it. my advice.. don't spend any more time and money on it. Between tech calls, printer speacialists, mac speacialist software and upgrades... i coulda bought a brand new one that was compatible! good luck! let me know if you find any thing that works!

  • I need help with MSI CR52-A2 52x24x52x CDRW Drive

    Hi,
    I am running Windows XP Home Edition.  My MSI CR52-A2 52x24x52x CDRW Drive will not work.  When I restart my computer the light on it flashes red, green, red, green, red, green, etc...  When XP is running, if I click on the drive under "My Computer" it opens up the drive but no files are found.  If I try to add new hardware, I'm told that the drive is working properly.  When I try to burn a CD with Windows Media Player I'm told no CD Burner is found on my system.  Please help!  Does this have to do with the BIOS?

    Welcome to the forum superaverage.  
    1) Before posting any problems related to your optical drive, please post full system specs AND PSU rails (look at my signature).
    2) Tell us how do you have your drive setup (Master, Slave, in primary channel or secondary channel).
    Edyros!  
    The recommended setup for ANY CD-R/W or DVD-R/W is to set them in the secondary channel as secondary master (assuming that your primary master is your HDD).
    If you're using nero as your burning program, try downloading the latest ASPI drivers for windows XP.
    Try flashing your drive's firmware to support more media and to fix minor bugs.
    ALWAYS use an 80-conductor IDE cable for ANY drive.

  • Need help with msi mega 180 + athlon xp-m combo

    Dear forummembers
    I had a question regarding the athlon xp-m. I installed the cpu in my mobo and it works at a slow speed. 600mhz (multiplier @ 6, fsb 100) So I used a pinmod. Now it runs at 1400mhz (multiplier @ 7x systembus and x14), but I have 2500+ m @ 45 watt or something so it should run at 1862. The problem is my fsb. It runs only at 100. How can I change the FSB? I selected in the bios fsb 133 but it jumps back to 100 all the time. I have the newest bios available, downloaded and installed with liveupdate. is it possible to set  the fsb in the bios, or do I have to change the pinmod again? I know the site for that: pinmod map viewer
    I selected socketview, barton and 7x systembuss + 133mhz and I checked and checked again. I did inserted the pinmodwires like it's shown. I used 5 cutted speaker fiber wires (copper) 
    My current speed is: 14x 100 mhz, but I want 14*133. The multiplier is correct, but the fsb isn't. What is the problem? Does anyone know?
    Here is an example picture, for people, who don't know what a pinmod is:

    AFAIK, you shouldn't need a pinmod for a Mobile Athlon XP CPU to work in a nforce2 mobo
    did you have any other CPU installed prior to this one? if so, refer here to clear the CMOS: Clear CMOS Guide
    next, refer to your manual, or download from MSI, for location of the FSB jumpers; ensure J8 is shorted across pins 1-2, and J7 is shorted
    finally, enter your BIOS setup menu, and under Advanced Chipset Features, set CPU FSB to 133mhz (or even 166mhz if you have DDR333 memory). the only thing i can't see in the Mega 180 manual is where you set the multiplier...
    which is where the BIOS has limited overclocking features, and you might have a problem here
    i think i'll pass this over to the Overclockers forum, where someone may be able to give a better answer....

  • Need help with MSI GeForce 6800. Pc says its an LE...

    Hi all I did a search but couldnt find anything relating to my problem. If I missed it then I apologise in advance.
    I bought an MSI 6800 and installed it but it says that the card installed is a 6800 LE.
    All the packaging and the stickers on the card itself say its a 6800 but the pc says otherwise.
    I installed all the software and searched for updates. I installed new drivers but still it says its an LE.
    How can I find out if I got a duff card or a problem with windows and drivers ??
    Is there a major difference physically on the pcb that I could check out ?
    cheers.
    JunkDuster

    Thank you very much for the pictures.
    I did what you said and guess what, yep, it said 6800 LE.
    I now have the great displeasure of having to pay for postage to return this item and hope that I can get a full refund and go elsewhere.
    That was the first and last time I will use that company again.
    Cheers for your help in stopping me from getting ripped off.
    JunkDuster

  • Need help with MSI GT70 0NC-029NE bluescreen problems

    I've just bought this new MSI computer, and downloaded a few programs like skype, steam, origins etc. When I open all of them at the same time, the bluescreen appears saying; memory management. The computer has 8gb ram, so it shouldnt really be a problem.
    Would really be nice with some help on this as it is quite annoying   

    Quote
    The computer has 8gb ram, so it shouldnt really be a problem.
    The amount of memory is not the problem, but a fault with the memory, or the memory controller (in the CPU) could be the problem.
    Is there a particular program that causes this BSOD?

  • Need help with msi 875p neo

    i just bought one of these and set up my system, but as soon as i flick the power switch on the psu there is a 2 sec delay then it automaticaly boots up without me pushing anything then it just hangs..nothing no boot screen nothing. i check that d brakect thing and it says "Inializing keyboard controller" it stays there and does not change.
    my system spec:
    msi 875P Neo-FIS2R
    intel Pentium 4 3.0GHz 800MHz Fsb
    2 x 256 mb pc-3200 OCZ EL-DDR cas 2 @ DDR400
    thermal take spark 7
    leadtek winfast A280leTD 'Geforce 4 Ti 4200'
    WD raptor 36.7 GB SATA 1
    Xaser III casing
    Thermaltake Purepower 480W
    MS intellieye Explorer
    plz help me i find no reason for it no to work

    Quote
    Originally posted by MaKoMaN
    thaks for all ur help i found the problem one of my memory sticks had a scratch the other one works fine.. but now what do i do with the scratched one?
    did you make the scratch? if not, you got warranty on it that would get you a new one...

  • MSI Enjoy 10 plus I have a problem with wifi

    I have a problem in connecting with wifi
    when I connect the device with my WIFI it says " obtaining IP address "
    and when I make the IP setting static and write my IP address and so on
    it said to be connected but the wifi bars are grey not blue so it just do not log the internet
    Itz Urgent I need your help, please

    Quote
    although it worked at my friend's house directly
    then is it a problem with my router ?
    If it works with your friend's wireless connection, then the problem must be with your router.
    What router is is? Does it have DHCP enabled?
    Quote
    P.S my iphone and my blackberry is working with my wifi connection and there is no problem
    Do they pick up an IP address automatically or are they manually configured?

Maybe you are looking for