I need help setting up airport express to play my Itunes music to my stereo

Hello I am hoping someone can help me as I am at a total loss here. I have had an airport express for a few years and would stream my music to my stereo without any problems. A few months ago it would cut out every now and again but soon it got so bad it was unlistenable. I reset it many times but to no avail.
Now when I try to reset it by opening the airport utility it scans but does not find the airport express.
I bought a pluglink ethernet adapter and connected it to the Airport Express hoping I can run it through that but when I open up the airport utility it scans but still will not recognize the airport express.
Is there some way to set this up .
I have an IMac which has the latest operating system.
Sincerely grateful for any help in this matter Paul K.

Hello blakemj. Welcome to the Apple Discussions!
For your described network configuration, you will want to reconfigure your 802.11n AirPort Express Base Station (AXn) as a "wireless client" to the Buffalo wireless router.
Here's how ...
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
(Note: As a third option, you can temporarily connect the AXn directly to an available LAN port on your Buffalo wireless router during setup, and then, place it at the desired location when complete.)
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing Buffalo's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

Similar Messages

Need help setting up airport express as bridge (Any help is appreciated)

Hello so before my wifi was switched I was able to use my 802.11g airport express as a wifi card for the xbox 360. I then decided to upgrade my main base station from an 802.11g base station to and airport extreme 802.11n. My problem is that my airport express cant extend the airport extreme network to my xbox anymore because they are different 802.11 versions. So can anyone help me configure this so I can get this back? Any help is appreciated.
My Current Setup:
Internet => Airport Extreme 802.11n => Wireless => Airport Express 802.11g (to extend network for xbox)=> Ethernet => Xbox 360
Thanks!

As I said, WDS is a nightmare for most users. Apple hides the settings from users to discourage use of WDS.
I do not recommend that you do this, but have a feeling that you will do this anyway.
I will not be able to help you sort out WDS problems.
On AirPort Utility 5.6, click Manual Setup
Click the Wireless tab below the icons
Hold down the option key on your Mac while you click on the Wireless Mode selection box and the WDS settings will appear
Apple's instructions for WDS are here:
http://support.apple.com/kb/HT4262
Hope this helps. Good luck.

Need help setting up Airport Express A1084 in Windows 7 via Netgear WNDR4500 wireless router

Hello All. I bought a used Airport Express A1084 off the net. Never had one before. My intention is to remotely control (via my iPhone using Apples Remote app or possibly XBMC) a "pc with music" and stream thru the AE connected to a boombox. I want to be able to take AE and boombox to the front yard, back yard, garage, or wherever my Netgear WNDR4500 will reach.
So far I have hit the reset on the AE and while holding, plugged it in to power (still holding) until the green light blinked. I let it go. Waited for it to complete booting (slow blinking yellow/amber light). The AE did not show up in Airport Utility ver 5.6.1. I uninstalled that version and installed older Airport Utility ver 5.4.2. Same results. I power cycled the router, turned off the Norton 365 firewall, and still get nothing. At one point though, I walked away for a while (an hour or so), came back and saw the AE listed in the left window pane of Airport Utility. I thought maybe I just didn't wait long enough so I clicked Manual Setup and it started to read the AE but Errored 10057. I tried again and got same error. I refreshed and the AE was gone.
Can someone tell me how to correct this so I can confirm I didn't buy a "brick"?
Thanks in advance,
Tom

Just so you are aware, the A1084 AirPort Express is a 802.11b/g wireless router that can only operate on the 2.4 GHz band. Regardless, it can be configured to join the wireless network provided by the Netgear as long as that network is configured to be backwards compatible with 802.11g clients. However, in the long run for performance, you do NOT want any non-"n" wireless clients connecting to your Netgear's network.
The 5.6.1 version of the AirPort Utility for Windows does not support the non-"n" version of the AirPort base stations. You would need to use an earlier version that will still run on Windows 7.
One thing to try would be to temporarily connect the Express directly to your PC using an Ethernet cable, and then, try accessing it with the AirPort Utility. If you are still unable to do so, you may have gotten yourself a defective unit.

Problems Setting-up Airport Express to Play Music thru External Speakers

Hi:
I have an HP dv6500z laptop connected to an HP printer C6280 via LinkSys wireless network using the LinkSys 54G router and PrintServer. It works fine.
I purchased an Apple Airport Express and want to connect it to this network so that I can play songs from within iTunes through external powered speakers wirelessly. The powered speakers are connected to the Airport Express (AE).
The AE is plugged into the AC outlet and the speakers are turned on. The AE is roughly 10 feet away from the laptop/router, just across the room. The AE's
LED is flashing amber (It does not yet recognize the network). I installed the Airport Utility from the enclosed CD, downloaded all patch upgrades and it installed successfully.
Now, how do I tell the Airport Utility to recognize and connect to my existing LinkSys network, so that the AE recognizes it ? The instructions are not clear on this note...they say to run the Airport Utility and then follow the on-screen instructions. The instructions tell you that you will lose your wireless network connection if you continue...and you do if you try.
The same information comes up if you try to do a manual install.
How do I connect the AE to an existing network ? This information seems to be missing. If I go to the AirPort Utility Help and search and search on Setting Up AirPort Express, it tells me the following:
Connect your stereo or powered speakers to your AirPort Express using the mini-jack on the top side of your AirPort Express, and then plug your AirPort Express into a wall outlet.
Open AirPort Utility, located in the Utilities folder in the Applications folder on a computer using Mac OS, and in Start > All Programs > AirPort on a computer using Windows.
Click Music in the toolbar, and select the Enable AirTunes checkbox.
Problem: What Music in What toolbar ? I do not see this...
Enter an iTunes speaker name and password. This is the name displayed in the pop-up menu at the bottom of the iTunes window.
Problem: Where does this information come from
If you're setting up your AirPort Express for the first time, choose Assist Me from the Base Station menu and follow the onscreen instructions.
It seems like something is missing from the setup.
Aaah...Just for the heck of it, I went under Base Station > Assist Me
and told it to continue even though the dialog box said it would change the network.
It displayed a tabbed dialog box where I could configure the AirPort Express, including a tab named Music.
Note:
The following two items are listed in Apple's on-line Help inside of Airport Utility, and on the web, yet I did not see them inside of Airport Utility when trying t oconfigure my AE.
I did not see a checkbox to check, named Enable AirTunes.
I did not see any place for entering the name and password for my speakers.
I followed all of the instructions and things looked like they were going well until I clicked Finish.
Them it said something like it could not save the settings..try again.
Well, I did, but when I brought Airport Utility back up, it kept saying that it could not detect the AE,
and when I went under the Base Station menu, all items were grayed-out, so I couldn't do anything.
Please help... the instructions need to clearer and more detailed.
Thanx, Dale
HP dv 6500z Windows Vista New Airport Express

Hi:
Thanx for your reply.
After several more hours of trial & error over the weekend,
I finally have the Green Light (LED) on the Airport Express.
And it stays green, even if I unplug it from the AC outlet,
and plug it back in later. I have the green light so this
tells me that I have gotten past one hurdle.
OK...in order to get this far, I had the AE wired to the
laptop or LinkSys router via an Ethernet cable. How do
I go about making this a "wireless" connection. LinkSys
told me how to take my laptop from a hardwired connection
to wireless, but it doesn't address the issue when you have
a 3rd party device hardwired that you want to make wireless.
Side Note:
I have not tried this yet, but I found a note on the web that
stated something like this: after getting the green light,
this guy then disconnected the Ethernet cable from the AE,
unplugged the AE from AC power for a few minutes, plugged it
back in to AC power, and voila! ... he was wirelessly on his network.
OK...let's assume that my AE is now on the wireless network.
What type of special settings do I need to make inside of iTunes
in order to get sound to the speakers.
I have my powered speakers recognized by iTunes...I can select them.
But, it appears that something may be blocking my AE from talking to
my network...I keep getting a pop-up box from Symantec saying that it
is detecting a "virus" (for lack of a better term) at the IP address
that I set my AE to. Oh, yes...that's another question...
When manually setting up the AE, I have my router network's IP address
(dotted-quad) in the list of parameter settings, but...near the top of
the list, the Airport Utility software asks for your AE's IP.
Well, what is it ? Nobody has told me ... Where do I get it from ???
Or...do I assign an arbitrary value to it based on the dotted-quad below ?
The router has an IP address of something like 192.168.1.xyz. I know what
the xyz is for the router but, what number do I use here for the AE, or
does it matter as long as it isn't being used by another network device.
My network is static.
So, after using a number not used by my network elsewhere (that I am aware of,
and...inserting a $ (to specify hexadecimal format)in front of my encryption password, NOT the router password (they intermix the naming of these) I finally managed to get the Green Light on the AE. Note: I am using the WEP-64 bit encryption which is also refered to a "40 bit" (No..not hexadecimal..$40 = 64) which is 40-bit to which a random 24 bit is added to give you 64 bit encryption.
To summarize;
I appear to have the AE configured via hardwire (I have the green light).
In iTunes, I can see and select my powered-speakers from the drop-down menu in the lower right corner, but i am s not yet streaming (hearing) the music.
It appears that Symantic may be knocking me off the network, or not letting the AE talk to the laptop/router...I have not yet tried this, but another nugget that I found on this site says to go to System Preferences (where?), click on the Firewalls tab, click Advanced , and uncheck "Block UDP Traffic".
Is this what may be blocking my AE talking to the laptop/router ?
Any help/feedback would be appreciated...Thank you.
I'm getting close...but no cigar (yet).
DaleB

I can't expand my Time capsule with an other airport to support wifi transfer itunes music to my stereo receiver.

I can't expand my Time capsule with an other airport to support wifi transfer itunes music to my stereo receiver.
I can see my time capsule in the airport configuration program, but not my airport. Not even when it is cabled.

On the side label find the model number.. A1084 for example is old. It will not work.
The new one A1392 and the earlier N wireless A1264 will both work.
http://en.wikipedia.org/wiki/AirPort_Express

Need help setting up older Express.

Heres what I have and what I want to do:
I have a 2005 Power Mac G5 (10.5.8) without built in wifi, I want to connect it to my network via Express in bridge mode(?). I cannot hard wire because of its location but it is well within wifi range.
I get thru the set up and have a steady green light and Airport utility says its connected to the internet but it seems that its not sharing thru the ethernet port.
After set up, the express reboots and cannot be found by Airport utility, I have to reset to try anything different.
My main router is not an Apple base station.
I can't seem to install (it fails) Airport utility 5.6 on my Macbook (10.7.5) to try a different set up. And I can't seem to find any solutions on the web for my situation. I have also tried set up via iPad and iPhone - no luck.
Thoughts, Suggestions, Solutions?
Thanks!

I get thru the set up and have a steady green light and Airport utility says its connected to the internet but it seems that its not sharing thru the ethernet port.
The older A1084 and A1088 versions of the AirPort Express do not have the ability to join a wireless network and provide an Ethernet signal at the Ethernet port, so if you have one of these models, that would explain the difficulties.
Look on the side of the AirPort Express to locate the model number, which may be difficult to see with gray lettering on a white background.
The more recent A1264 and current A1392 version of the Express are capable of doing what you want.

I need help configuring the Airport express from a PC

Hi there!
I want to configure the airport express from a PC. It runs okay but the connection is open (anyone can browse on my connection)
In a PDF that I found on Apples web site, it says go to
Start-> All programs-> Airport express setup assistant, but there are no programs named Airport on my PC!
Do I have to download a utility for this purpose?
Fredrik

If all you want to do is add wireless security to an already configured Express, you'll probably want to use the Airport Admin Utility. You should be able to install it by installing this package:
http://www.apple.com/support/downloads/airport42forwindows.html
If the PC isn't running at least Windows XP, I think you're out of luck.

Need help setting up external hardrive to play itunes on 2nd Mac

I have my main music collection on my Mac Pro (400 gigs). I want to be able to use my Mac Mini downstairs to play my itunes collection. I have attempted the following steps without success:
Using my Mac Pro, I formatted a 2TB Seagate drive into two partitions (one to use as timemachine back up for the Mac Mini) the other to copy my itunes collection to.
I copied my entire itunes folder onto that Seagate hardrive partition which I named :"Mac mini Itunes"
plugged in seagate hardrive to the mac mini
Opened itunes using the hold option button to choose the iTunes library on the external hardrive
When I chose the iTunes folder located in that "mac mini iTunes" hard drive icon on my desktop, I get the following message:
"The iTunes Library file is locked, on a locked disk, or you do not have permission for this file"
When I go to the Sharing and Permissions info on that "mac mini Itunes" hard drive icon, it shows "You can only read"
Below that I see that the Name and privilege info is grayed out and I can not change anything.
The Ignore ownership on this volume is checked but grayed out and I can not change it.
Any suggestions on how I can use this hardrive to play my iTunes collection on my mac mini?
Do I need to reformat the Seagate drive and do something different while partitioning the drive?
Should I reformat it using the mac mini instead of the Mac Pro and then copy my iTunes folder to it?
Thanks for any help

Hello blakemj. Welcome to the Apple Discussions!
For your described network configuration, you will want to reconfigure your 802.11n AirPort Express Base Station (AXn) as a "wireless client" to the Buffalo wireless router.
Here's how ...
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
(Note: As a third option, you can temporarily connect the AXn directly to an available LAN port on your Buffalo wireless router during setup, and then, place it at the desired location when complete.)
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing Buffalo's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

I want to use the Airport Express to play my iTunes through the house

I moved into a house that has speakers throughout the house. The speaker cables from the speakers are terminated in one location in the basement entertainment area. One thought is to hook up the speaker cables to a speaker selector to setup zones in the house. However, I would like to integrate the Airport Express device to this. It would be awesome to be able to play my iTunes library through the house. I see that there is a 3.5mm output from the Airport Express. Does anyone have a recommendation on how I might be able to set this up? Do I have to buy a stereo receiver that takes the 3.5mm output from the Airport Express and then hook the receiver up to a speaker selector? Any thoughts or tips would be greatly appreciated.

One option is to get an AV receiver that supports both whole-house connectivity and AirPlay. You would connect all of your speakers to this receiver. The receiver would control which rooms get sound. In turn, you would stream from any AirPlay-ready device to the receiver. You can also substitute an AV receiver that does not support AirPlay directly. In this case, you would connect an AirPort Express to the receiver's digital optical audio port and send the streams to the Express instead.

Airport Express 802.11n for iTunes music?

I am a happy user of an older Express 802.11g for playing iTunes music. Would there by any advantage to getting an N solely for this purpose? I don't use the Express for anything else on my network, and I don't think that the speed increase with N would show any increase in audio quality etc., or am I missing something?
Mike

Mike,
Here is some food for thought.
If your printer is OFF, then the rest of the network would be running "n" speed if you replaced the Express with an "n" version.
When you turned your printer back on, the network would basically be running "g" at that time.
I have a "b" wireless printer... Yikes.... Here is what I did.
I plugged my printer into the back of the TC (basically same as the Extreme) with an ethernet cable and turned OFF the wireless printing card.
Now my entire wireless system is "n" including sending information to the printer.
Printing and reading camera cards is much, much quicker...
Just some more ideas for you and a way to spend your money.........
Joseph Kriz

Need help setting up airport on G3 iMac

Hi All,
Similar issue with an old iMac I bought for my girlfriend on ebay.
Just inserted the wireless card I bought for it. The router is a british (BT Home Hub3) wireless N, the machine is an iMac G3 400Mhz running Panther, I'm guessing the same issue applies to set the router to WEP/WPA as currently I can't see it listed at all so cannot connect?
Many thanks.
Phil
<Edited By Host>

For 10.3 you will be limitted to what browswers you can try. The newest version of Firefox for 10.3 will not surf the web that well. You need to be running Tiger to get a decent port of Firefox... TenFourFox.
I recommend one of these browser for 10.3.
Opera
http://www.opera.com/browser/download/requirements/
http://www.opera.com/download/
OmniWeb 5.11, which, I believe is built on the same framework as Safari 5,
iCab - The Taxi for the Internet
http://www.icab.de/
Some folks have gotten Tiger cds out of Apple. ( some related to what you say. )
AppleCare Support Phone Number: 1-800-275-2273
open 6am to 6pm Pacific Time
Apple Phone Sales 1-800-692-7753
International Technical Support Numbers
http://www.apple.com/support/contact/phone_contacts.html
Robert

Need help setting up AirTunes

I am having trouble setting up AirPort Express to play my iTunes music to my stereo. I have a MacBook which is connecting wirelessly to the Internet via my Linksys router (which also connects a PC). I always thought it didn't matter
since you can just plug in your stereo into Airport Express and Airport Express would find the network, but setting up a connection to Airport Express always disconnects my Linksys connection and then iTunes does not pick up the remote speakers. I already set preferences in iTunes to search for remote speakers. Am I missing something here? The amber light blinks on the Airport Express, but I do not want to use Airport Express for the Internet, just for Airtunes.

Hi.
This article is helpful.
http://docs.info.apple.com/article.html?artnum=302153
I have found it easier to use AirPort Admin Utility than the Setup Assistant.
Rachel
iMac Core Duo 17" 1GB RAM Mac OS X (10.4.8) MacBook 1.83GHz 1GB RAM; iPod nano

I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?

I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?

Before I bought it I did the same question at the Apple Store, and they told me "You can extend your existing Wi-Fi Signal with Airport Express wireless...
You cannot extend wireless from any brand except another apple router.. the store might have assumed you were using an apple main router. Most people who buy express buy them to extend an extreme or time capsule.
You are correct .. in the setup documents it does say 5.6.1 is adequate to do the setup.. my bad.. !!

HT4259 Trying to set up airport express to extend my wireless network. Primary base station is a time capsule. Even when I plug in the airport express to mac it cannot find it.

Trying to set up airport express to extend my Wi-Fi network. Primary base station is a time capsule. Tried searching for airport express using Wi-Fi status, no luck. Even tried plugging airport express into iMac, still no luck. Airport express showing solid amber light. Thanks for any help.

Airport express showing solid amber light
Unfortunately, this can mean one of two things:
1) The Express is locked up and will need a Factory Default Reset procedure to try to return the device back to its original default settings so that it can be reconfigured again.
2) The Express is defective. If you cannot get the Express back to a slow, blinking amber light after a Factory Default Reset, the Express will need to be replaced.
Try the Factory Default Reset a few times and report back on your progress.
Resetting an AirPort Base Station or Time Capsule FAQ

Can you guide me step by step in setting up airport express as a wireless extender for an existing Airport extreme network

Can you guide me step by step in setting up airport express 802.11 as a wireless extender for an existing airport extreme network?

Also check out:
Re: Need Help Networking AirPort Exp to Existing AirPort Extreme
Re: How to connect AirPort Express to existing AirPort Extreme Network...

I need help setting up airport express to play my Itunes music to my stereo

Similar Messages

Maybe you are looking for