I need port forwarding help for xbox live. I have a WRT54G router.

I forwarded the ports but it still says I have a moderate NAT. I think I need to get a static IP address on my PC and I know how but what DNS servers do I put in. When I made my static IP the internet didn't work and I figured it was the wrong DNS servers. Do I also have to switch anything in the router settings? Like switch from DHCP to static IP? Any help would be appreciated.
PS. I know nothing about routers and will need to be told where to switch things.
TYTY

in order to open the ports for the x-box , u need to assign a static ip address on the x-box itself and not the pc.....it should be anywhere in between the following range
192.168.1.2 to 192.168.1.99 or
192.168.1.150 to 192.168.1.254
the dns numbers would be the one from the status page on the router ui...to access the router ui , you need to type http://192.168.1.1 .. logon using "admin" password......on the setup page , adjust the mtu settings to 1365.....under "applications and gaming" , open ports 88 and 3074 and give the ip address of the x-box...

Similar Messages

Ok i need lots of help here... i have a WRT54G router and...

ok i need lots of help here... i have a WRT54G router and trying to hard wire a computer to it and wirelessly connect to a laptop... i have dsl internet connection... the power light is blinking constintly and when i try to setup the router the default password doesnt work already tried to reset the router and that didnt help... any thoughts> thanks

the power led blinking all the time can be caused by a corrupt firmware, or a defective power adapter, try doing a hard reset, you may need to do it a couple of times, and then power down both the modem and router.
after a couple minutes, power up the modem, wait for the link led lights up, then power up the router and look for it to link up with the modem, at this time the power led on the router should be on solid if all is ok.
if it still don't light solid, you may need to do a firmware update, or the router is defective.

WRT320N. Port forwarding help. Xbox and ps3 playing at same time. NAT issues

Hi
I'm trying to have both my xbox and ps3 play with open NAT's for online gaming. I have had success utilizing info from 'portforward.com'. But the solutions will unlock OPEN NAT for either the ps3 or the xbox .. one at a time. Is there a way to get both to be open?
It seems like one main conflict is the success depends on both utilizing port 3074. But I can't have both use it? ( obviously).
I tried port forwarding the xbox per specs off of this forum and that works great.. And DMZ ing the PS3. But like i said before. Most solutions
leave one console with OPEN and one with Moderate.
Is there a solution that allows both NAT OPEN's on both consoles?

First of all XBOX works on a different port number and PS3 works on a different port numbers. Follow the steps below to open the ports on your router for XBOX and PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
This settings are for your XBOX.
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
For PS3 Follow the steps below
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.

Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.

Mac OS X 10.6 Help: Sharing your Internet connection

Need to do projects for CP C++ course , have team viewer, bought Parallels, but were told there's no need to buy anthing since Mac can code. Do I need a compiler then, which one? Thanks.

Need to do projects for CP C++ course , have team viewer, Xcode, bought Parallels, but were told there's no need to buy anthing since Mac can code. Do I need a compiler then, which one? Thanks.

Xcode. Download it for free from the Mac App Store.

How to I use my Ipad mini with keynote to project my presentations, do I need any other app for that?I have a lighting to VGA cable already

How to I use my Ipad mini with keynote to project my presentations, do I need any other app for that?I have a lighting to VGA cable already

If you are using Keynote, then no, you would be fine with just the adapter and a cable hooked up to the projector.

Hi can anyone help. I have the wrt54gs router which work...

hi
can anyone help. I have the wrt54gs router which works ok untill I switch my computer off or put it into standby it then switches the router off which disconnects my sons ps3 connection. any help greatly appreciated

try changing the router's MTU for wired and change the advanced wireless settings on the router as well.

Port Forwarding for Xbox Live

My eyes are burning from trolling the boards all day. Just picked up an AEBS (12:33 PM CST, 4/20/08), firmware's at 7.3.1, connected the ol' xbox and got a "moderate" on my NAT test. Thats fine, totally expected, no big deal, right? So here's what I do:
1. Assign static ip ads to all machines on the network (xbox is 10.0.1.3)
2. Check to see if NAT is enabled in airport utility: Yep.
3. Enter in the ports as usual:
Public UDP Port(s): 88,3074
Public TCP Port(s): 3074
Private IP Address: 10.0.1.3
Private UDP Port(s): 88,3074
Private TCP Port(s): 3074
The above, BTW, is exact as far as commas and spaces go.
4. Update!
Then, NAT test= Moderate.
OK, it'd be nice if there was a standardized way to forward ports on all routers, I think, no big deal, just need to do a little tinkering.
I put a space after the comma between 88 and 3074, i.e., instead of 88,3074 I did 88, 3074. Moderate. I tried putting a dash in there (88-3074) wouldn't even let me do that, but of course we all already knew that. Tried rearranging all the ports randomly (3074,88). Nope. Well, even though I just gave the machine a static ip address, might as well try a DHCP lease: enter Airport ID. Nothing. Try it again with Ethernet ID. Nothing. I've got an idea, I'll make multiple separate port mapping profiles:
xbox 1: Public UDP Port(s): 88...
xbox 2: Public UDP Port(s): 3074...etc.
NAT test= Moderate.
Hmm, Oh they make port forwarding management software? Lighthouse, eh? I'll try that...oh, it doesn't do anything: Moderate.
I tried a bunch of other things that I knew would be futile, but I've been working on this thing for a couple of hours now and I can't remember them...Oh and by the way, for those not familiar with xbox live: "Moderate"= not good.
I'll telepathically make you feel better if you can help me out.
Love ya,
Boo

Thanks for the prompt reply Duane. Just to clarify: I need another wireless router? I thought airport express was one. I was trying to configure the ports of the airport express's basestation. My connection system is:
-An ADSL 2mbps connection that comes into my home from a phone line and into a D-link GLB 802C modem
-This connects to an Airport Express
-My macbook pro uses the net through the wifi signal provided
-I connect the macbook pro to the xbox through an ethernet cable (mainly because it's far from the adsl router)
I have read that one can forward ports with airport express...

Need Help Blocking Xbox Live Ports on ES4200

Can someone instruct me on best method for blocking access to Xbox Live on my ES4200? I want to prevent my niece/nephew from hogging bandwidth and/or limit/restrict their usage. Please advise.
Thank you,
Nicky

Hi Nicky, is your router E4200 or ES4200? If your Xbox is connected wirelessly, all you need to do is access the setup page of the router. Look for this page http://ui.linksys.com/files/E4200/1.0.00/Status_Lan.html and click the DHCP client table option.
You will find the MAC address of your Xbox on the list, just take note of it and go this tab on the page http://ui.linksys.com/files/E4200/1.0.00/Wireless_MAC1.html. Once you're there, enable the Wireless Mac Filter and select the option Prevent. Input the Mac address of the Xbox on the list and make sure to save the settings. Hope this will help you. Update us!

Application And Gaming / Port Forwarding || HELP NEEDED || Can Only Access Via LAN

Hi.
I have just bought a Wireless Router, Model Number: WGKPC354G-UK. With the intention of setting up a small server. This server will run from my PC (directly wired into router), running a game called "Counter Strike" - I had to download a dedicated-server tool for this and i successfuly installed this and followed the tutorial to set it all up..
So I thought i had done it, but I could only access my server with my internal IP 192.168.1.64 (LAN).
I then found out that i needed to "Port-Forward" I followed a tutorial on www.portforward.com - This showed me how to open the ports, and which ones to open.
I did all this and i still encounter the same problem !
So i then opened all my router ports "DNZ" and it still doesnt work !!!
Any help will be greatly aprreciated !
PS. Below Are The Required Ports.
http://portforward.com/english/routers/port_forwarding/Linksys/WAG354G/Counter_Strike.htm

Keep in mind your ISP could be blocking the ports needed. DMZ almost ALWAYS works and if it doesnt, most likely your ISP blocks the ports.
another test is to make sure you can connect to the game server from another CS machine on the inside of your network. If this works, that means your server is up and running properly and its probably your ISP blocking certain ports needed for the CS Server.
You should also check you have the Windows firewall disabled, and any other software firewall on your server disabled.

Port Forwarding HELP NEEDED!!!!

I have a HomeHub v2 and I just cannot get the 25565 port open!
I have it opened in the router settings exactly as all the guides say to do it however http://www.yougetsignal.com/tools/open-ports/ still says it's closed!!!!!!
Please help, what am I doing wrong???

As well as the suggestion above, you also need to check that the IP address/Device Name that the Port Forwarding is assigned to is available. You should use ping to check this locally first.
Due to the IP address being dynamic (able to change when the DHCP lease expires), it is sometimes easier to set a static IP address on the device you are forwarding to.
Settings->Advanced->Home Network->Click on Device->Always use this IP address. While you are there, check that this device corresponds to the IP address/hostname that you have Port forwarded to.
For your convenience, Home Network link here:
http://192.168.1.254/hnet_device.lp?be=1&l2=0&l0=2&l1=3

Need help for SB Live

Need help for SB Li've CT4850 driver for windows 7. Thanks

Hi,
I don't think there is a Windows 7 driver for this model. If you just purchased this card, I suggest you take it back to store for something newer.

Open my NAT for Xbox live

Please I need help opening up this NAT on my time capsule. It's making my Xbox lag and drop out of games. I have 3 boxes, 2 iPhones, and desk top iMac.

Does that mean 3 xboxes??
Basically the TC is the wrong router for you.. xbox is designed to work with upnp that is vista compatible at least. It can then automatically open the required ports.. you cannot run multiple xboxes with fixed port forwarding as it is impossible to set a port to forward to more than one location. Upnp can negotiate a different port.. nothing else can. Apple of course could never use a MS designed automatic port opening system so adopted their own, NAT-PMP.. which is totally great for when apple introduce their game console.. but useless for your xbox.
Buy a router that is known to work with xbox.. bridge the TC and plug it into the router and use it for backups or wireless or even a very limited switch.. just not NAT.

Port Mapping / port forwarding - help please...again...

Hi,
I am trying to use port forwarding/port mapping but after numerous failures to access my computer from an Internat connection, I am seeking advice or guidance.
I have a 2011 Apple Time Capsule, and under the Advanced tab on Airport utilities, Port mapping I have chosen +
it then comes up with a box in which I have entered the following:
Service - drop down menu (number of options...but have been advised on other threads to leave as is)
It then has 5 boxes:
Public UDP port(s) - 9080
Public TCP ports(s) - 9080
Private IP adress    - 10.0.1.x
Private UDP Port(s) - 9080
Private TCP Port(s)   -9080
note I have enabled NAT port mapping protocall. My ISP has advised that I cant use port 80 for some reason...but all others should be ok
note also the 10.0.1.x is a static address i have assigned to teh camera.
I have a dns provider, and when I use the URL on my LAN - I can access the camera....but as soon as I tryu to access via the WAN - it is unable to reach the server.
Other points - the TC is in normal mode (i.e. not Bridge)
Does anyone have any idea if I have set port mapping up correctly; any way i can test, any ideas how i can fix this??
I have tried this on a number of forums thus far - but no success to date.
Welcome all and any help!!!

LaPastenague wrote:
Have you reset the camera web page to use 9080?
i have checked again and in teh advances settings of my camera - it asks for HTTP port, HTTPS port, and for Nata Traversal it asks for an alternative HTTP port.   I have entered 9080 against all of these.
The TC is in normal mode ie as a router.. what modem do you have in front of it? Is it in bridge? Does the TC get the public IP or does the modem route the address as well? You will have no success via double NAT.
not sure what brand the modem is - but i can confirm it is set up as a modem only with both the router and wireless functions turned off.
The Modem is not in Bridge mode - neither is my ATC. The ATC gets the public IP address via the adsl modem. so double NAT should not be an issue
When you say you can access the camera using URL on lan, is that using the new port 9080? Please give explicitly what address you use.. (you can hide the full public address) and port.. and AFAIK this should NOT work as the TC would have to handle NAT Loopback which would amaze me if it does. According to all the info around the web the TC has no NAT Loopback and therefore should not be able to handle the address. I need to know therefore the exact address you use
this is actually using the url that my dns provider provides to me as i do not have a static ip address.   albeit this appears temperamental as to when it works sometimes from my LAN. after which it requests user name and password and I can then see the live stream.
one problem I have just noted is that when checking teh DNS setup - it still appears to default to port 80 which my isp has advised i can not use) so i am checking with teh dns provider how i change this.
The good news is port mapping must work on my ATC, as I have just set up my slingbox using their automatic port mapping assistant and it seemed to set up with no issues...i have also just confirmed that the stream can be viewed on the internet.

Trying to change NAT connection from moderate NAT connection to an open NAT connection for XBOX LIVE

Hi, I have a Linksys Wireless-N Broadband Router/WRT160Nv2 and I have been trying to change my NAT connection from a moderate NAT connection to a open NAT connection for my Xbox Live on my Xbox 360. I can sign into my Xbox Live account but it is working on a moderate NAT connection. I have already enabled the UPnP and put in the proper port numbers. After doing that I signed into my Xbox Live on my Xbox 360 and tested my Xbox Live connection and still it says that I a moderate NAT connection. I do not know what elso to do and I would greatly appreciate step by step help from anybody who knows what they are doing. PLEASE HELP ME AS SOON AS POSSIBLE!!!!
Thank you

A known issue with Linksys routers is the NAT Type 3 or anything related to dropping of Internet connectivity during play time. Network Address Translation (NAT) is the ability of a router or firewall to translate a public IP address to a private IP address and vice versa. It adds security to the network by keeping the private IP addresses hidden from the outside world.
Here is the link, which will you in resolving the concern: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=2902de6218ed4dc1a4c595595ca1f60a_Resolving_NAT_Typ...

I need port forwarding help for xbox live. I have a WRT54G router.

Similar Messages

Maybe you are looking for