I need to interface SCC-TC02 with help of SC 2345 and PCI-6024E DAQ Card.please tell me the procedure and if possible send me the program

Dear Friends,
I need to interface SCC-TC02 with help of SC 2345 and PCI-6024E DAQ Card.But i can not understand example program.please send me the procedure to interface these three componnets and if possible send me the program.
With Regards,
Eswaramoorthy K V

nce of nth triggering pulse. i need to know when the when the ist trigger occurs and when the nth trigger occurs . please tell me how to to . what i know is that event triggering has to be done with start and stop trigger. please tell me how it has to doneSuresh;
What you will need to do is to set up a digital start and stop triggered Analog Input acquisition. Then you will need to have a counter set as event counter, having the specific number of pulses you need configured as the preset value, configured to count down, and generating a pulse after the terminal count has been reached. That counter output will be the stop trigger of the Analog Input operation. In summary, you will have the external pulse being both the digital trigger of the Analog Input operation and the source pin of the counter, and the counter output being the digital stop signal for the analog input.
I'm attaching a Labview VI that does the start and stop analog input acquisition. You will need to include the counter part and set the stop s
ignal to be the counter output.
Hope this helps.
Filipe
Attachments:
AI_Start-Stop_D-Trig.zip ‏25 KB

Similar Messages

Hello, okay? since then, was robbed today, and my find my iphone this down, please tell me if he has a way to locate the computer, I need the iphone again, it has many important data it please help me

hello, okay? since then, was robbed today, and my find my
iphone this down, please tell me if he has a way to locate the computer, I need the iphone again, it has many important data it please help me

It's gone and you most likely are not getting it back.
If you had important info on it, you should have made backups so you would not lose the data.

What is the maximum number of samples that can be acquired with a single trigger using PCI-6036E DAQ card?

1. My PCI-6036E card has a FIFO of 1024 bytes in AI. Maximum how many samples can be acquired with single trigger for digitizing a waveform?
2. PCI-6036E DAQ card has got a AO with 10ks/s update rate? Can I generate a pulsed output with the AO of this card? I need a pulse of, say, 5 V and 1 kHz frequency.

Giri,
1.The trigger is usually for enabling the acquisition. I mean, when it is logic zero, you acquire nothing; however, when it is logic one, you start acquiring your waveform,and you can acquire continuously without having to worry about how many samples, unless you want to set your program for doing so. You can acquire continuously by implementing buffer acquisition. Finally, the FIFO that is in the board will not affect the buffer acquisition.
2.Yes, you can do that! You can generate your 5V signal with that specific frequency, and you should not have any problems, because the freq fits in the update rate.
I hope this information is helpful.
L Aguila
Applications Engineer
National Instruments

Mac G4 crashes using continuous generation with PCI-1200 DAQ card

I've been trying to use a PCI-1200 DAQ card with a Mac G4 to create a continuous analog output signal. The problem is that the computer locks up after a while (a few minutes). I have been using the Generate Continuous Sine Wave vi, but the problem remains.
I've tried slow signals (10Hz) and fast signals (2kHz) but the computer still seems to crash. I have no clue what is going on!

bissdp,
The first thing I would recommend is making sure you have the latest version of the driver:
www.ni.com > Support > Drivers and Updates > Current Versions > Multifunction DAQ
Another you could try is to determine what component is causing the computer to lock up. Use a process explorer utility to try to see what processes are locked up. A search in google might turn up utilities like this one: (http://www.clarkwoodsoftware.com/peekaboo/)
Keep in mind heat or speed issues. It may sound funny, but you may want to try opening the computer case and making sure the board has enough air flow to keep it cool.
These are just some ideas for now, I hope they help.
Alejandro Asenjo
Applications Engineer
National Instruments

How do you pay for apps with credit on your account from an itunes gift card that has already been redreemed and the credit id on the account?

how do you pay for apps with credit on your account from an itunes gift card that has already been redreemed and the credit id on the account?

jen19 wrote:
how do you pay for apps with credit on your account from an itunes gift card that has already been redreemed and the credit id on the account?
Just buy something.

Once completed the form, is it possible to receive the confirmation e-mail with a link addressing to a html archive?

Once completed the form, is it possible to receive the confirmation e-mail with a link addressing to a html archive?

I don't know if it is the best solution but you could filter the results to just that client's answers on the summary tab and then PDF that.

How to avoid dependance between output digital port with a PCI 1200 daq card?

Hello,
I don't manage to fix the state of a line on one port (PA0 for ex) without change the state of another line of another digital port (PB0 for ex)
I use a PCI 1200 Daq card with Labview 5.0.1 (under Windows 98)
How to configure a robust state (high logic level) on a line of a port??
Does anybody have an idea on this problem?
Thanks a lot in advance and happy new year to the community
JF LAVEZARD

jflab a écrit:
Hello,
I don't manage to fix the state of a line on one port (PA0 for ex) without change the state of another line of another digital port (PB0 for ex)
I use a PCI 1200 Daq card with Labview 5.0.1 (under Windows 98)
How to configure a robust state (high logic level) on a line of a port??
Does anybody have an idea on this problem?
Thanks a lot in advance and happy new year to the community
JF LAVEZARD
Hello,
I've found the problem
The PCI1200 has a chip 8255 for Digital I/O
If I use the bad VI, it reconfigures the port and all the lines go in a low logic state
so I'd to write only on the port or the line without reconfigure the port
So the good VI in the palett is: Port Write and not Digital Port write!
See attached file..
Thanks
Best Regards
Attachments:
port_dio.jpg ‏771 KB

HT4759 I sent Cloude maseeg for my phone to update my device stoped no work And then I want to please open a support device and thank you and I am currently in Cairo, Egypt with me

I sent Cloude maseeg for my phone to update my device stoped no work And then I want to please open a support device and thank you and I am currently in Cairo, Egypt
<Edited By Host>

Not what you want to hear, I know, but this is a user to user forum. No one here has the power to help you.
You can get information about an order you placed on the Apple Online Store through the Order Status page. If you prefer, you can also get order status or make changes by phone at 1-800-692-7753.
You can try calling again and if the person you speak to can't help, ask to speak to a supervisor.

TS3988 I sent Cloude maseeg for my phone to update my device stoped no work And then I want to please open a support device and thank you and I am currently in Cairo, Egypt with me and I Mobinil SIM and number, 01281081731

I sent Cloude maseeg for any phone to update my device stoped no work And then I want to please open a support device and thank you and I am currently in Cairo, Egypt with me and I Mobinil SIM and number, 01281081731

Try this here:
http://docs.info.apple.com/article.html?artnum=93499
"Windows confuses iPod with network drive and may keep iPod from mounting or songs may seem to disappear"
And since you are teh savvy about these sort of things, here's Microsofts support article for the drive issue:
http://support.microsoft.com/default.aspx?scid=kb;en-us;297694
"New drive or mapped network drive not available in Windows Explorer"
Good luck

Unable to Locate Bridge CS6 for Download. All I See Is the CC Version, which Never Works Well With My School Assignments. Please Tell Me Where I Go to Find this Cuz the PullDown Arrow Is No Longer Available. BTW - I Didn't See It Listed Under Previous

All I See Is the CC Version, which Never Works Well With My School Assignments. Please Tell Me Where I Go to Find this Cuz the PullDown Arrow Is No Longer Available. BTW - I Didn't See It Listed Under Previous Versions Either.
thanks!

Lyleb64687719 have you utilized the steps listed in CC desktop lists applications as "Up to Date" when not installed - http://helpx.adobe.com/creative-cloud/kb/aam-lists-removed-apps-date.html to verify the Creative Suite 6 version was not available? What type of a Creative Cloud membership do you have?
You can also download the Creative Suite 6 installation files from Download CS6 products. Installing any of the applications or suites which include Bridge CS6 should allow Bridge CS6 to install.

HT201363 I don't remember my two security questions and I saw where you could send it to your email but the email it shows I could send it to is not the email I set up with it is there a way I can change the email on there to send to the email I have

I don't remember my two security questions and I saw where you could send it to your email but the email it shows I could send it to is not the email I set up with it is there a way I can change the email on there to send to the email I have?

The Best Alternatives for Security Questions and Rescue Mail
     1. Send Apple an email request at: Apple - Support - iTunes Store - Contact Us.
     2. Call Apple Support in your country: Customer Service: Contact Apple support.
     3. Rescue email address and how to reset Apple ID security questions.
An alternative to using the security questions is to use 2-step verification:
Two-step verification FAQ Get answers to frequently asked questions about two-step verification for Apple ID.

I get the error ox80090318 with my itunes when i try to get itunes store please tell me what to do?

I get the error ox80090318 with my itunes when i try to get itunes store please tell me what to do?

http://support.apple.com/kb/TS4123
You do this; follow the article, if unsucessful call Apple Support

HT5622 I am trying to purchase an app from app store but it says your card is not valid or your card has been declined. I do all online payments with that card.Please tell me how should i proceed??

I am trying to purchase an app from app store but it says your card is not valid or your card has been declined. I do all online payments with that card.Please tell me how should i proceed??

Contact iTunes Store support.

Help needed I updated my ipad2 with iOS5 but few of my dashbaords are not working now can any one let me know how to downgrade the OS

Help needed I updated my ipad2 with iOS5 but few of my dashbaords (HTML5) are not working now ,can any one let me know how to downgrade the OS as we have a meeting coming up .. its urgent

Downgrading the iOS is not supported. If you are using Safari this try clearing its cache via Settings > Safari.
If that doesn't work then try closing Safari completely and then re-open it : from the home screen (i.e. not with Safari 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Safari app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
A third option is a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Calculate the total value of payments with the procedures and triggers?

Hello!
I work for a college project and I have a big problem because professor requires to do it by the examples he gives during the lecture. Here's an example that should be applied to its base, so please help!
I have three table with that should work:
Invoice (#number_of_invoices, date, comm, total_payment, number_of_customer, number_of_dispatch)
where:
number_of_invoices primary key (number),
date (date),
comm (var2),
total_payment is UDT (din - currency in my country) - in this field should be entered value is calculated
number_of_customer and number_of_dispatch (number) are foreign keys and they are not relevant for this example
Invoice_items (#serial_number, #number_of_invoices, quantity, pin)
serial_number primary key (number),
number_of_invoices primary key (number),
quantity (number),
pin foreign keys (number)
Item (#pin, name, price, tax, price_plus_tax)
pin primary key (number),
name (var2),
price, tax, UDT (din) not relevant for this example
price_plus_tax UDT (din)
These are the triggers and procedures with my calculation should be done:
trigger1:
CREATE OR REPLACE TRIGGER "trg1"
BEFORE INSERT OR UPDATE OR DELETE ON Invoice_items
FOR EACH ROW
BEGIN
     IF (INSERTING OR UPDATING)
     THEN
          BEGIN Invoice_items.number_of_invoices := :NEW.number_of_invoices; END;
     ELSE
          BEGIN Invoice_items.number_of_invoices :=: OLD.number_of_invoices; END;
     END IF;
END;trigger2:
CREATE OR REPLACE TRIGGER "trg2"
AFTER INSERT OR UPDATE OR DELETE ON Invoice_items
DECLARE
doc NUMBER := Invoice_items.number_of_invoices;
BEGIN
     entire_payment (doc);
END;procedure
CREATE OR REPLACE PROCEDURE "entire_payment" (code_of_doc IN NUMBER) AS
entire NUMBER := 0;
BEGIN
     SELECT SUM (a.price_plus_tax * i.quantity) INTO entire
     FROM Item a join Invoice_items i on (a.pin = i.pin)
     WHERE number_of_invoices = code_of_doc;
     UPDATE Invoice
     SET total_payment = entire
     WHERE number_of_invoices = code_of_doc;
END;As you can see the procedure is called from the triggers, I have a problem at the first trigger, and I think it will be even higher in procedure because UDT, field "total_payment".

I was not here a few days because I was trying to get additional information related to this problem. Professor gave me the information that I need to introduce a package and variable to get this thing work. But including that I still have problem. I hope that this time is less of a problem and that someone will be able to help me.
I also noticed that it was not a smart idea to try to translate the names of tables and attributes. That make trouble for me, especially you who are trying to understand and to help me, and absolutely nothing that will change the attribute and the table name will be. So this time I will set out the problem with the original name again to avoid confusion.
So, I try to base Implement optimization technique called: Repeating Single Detail with Master (so writes the slides that I received from professor, I hope that will mean something to you)
These are the lines of code that we get on the slides and should implement in the base, again I remind you that at this time in its original form, without translation.
- First create the package variable:
create or replace
package paket
AS
sifra number(10):=0;
end;This part is ok and it works.
- Secondly, it is necessary to create the first trigger:
create or replace
TRIGGER aktuelna_cena1
BEFORE INSERT OR UPDATE OR DELETE ON cena_artikla
FOR EACH ROW
BEGIN
     IF (INSERTING OR UPDATING)
     THEN
          BEGIN paket.sifra := :NEW.sifra_artikla; END;
     ELSE
          BEGIN paket.sifra := :OLD.sifra_artikla; END;
    END IF;
END;This part is ok and working.
Now the problems begin.
- It is necessary to create another trigger that will call the procedure:
create or replace
TRIGGER aktuelna_cena2
AFTER INSERT OR UPDATE OR DELETE ON cena_artikla
DECLARE
     s NUMBER := paket.sifra;
BEGIN
     aktuelnacena (s);
END;I suppose the trigger have problem because procedure is not ok.
I will copy error that I get from the compiler:
Error(7,2): PL/SQL: Statement ignored
Error(7,2): PLS-00905: object NUMBER6.AKTUELNACENA is invalid
And finally, it is necessary to create the procedure:
create or replace
PROCEDURE aktuelnacena (SifraPro IN NUMBER) AS
aktCena artikal.aktuelna_cena%type;
BEGIN aktCena:=0;
                SELECT cena INTO aktCena
                FROM cena_artikla
                WHERE sifra_artikla=SifraPro and datum_od=
                                (select max(datum_od)
                                from cena_artikla
                                where sifra_artikla = SifraPro and datum_od<=sysdate);
                UPDATE artikal
                SET aktuelna_cena = aktCena
                WHERE sifra_artikla = SifraPro;
END;I will copy error that I get from the compiler:
Error(10,57): PLS-00103: Encountered the symbol " " when expecting one of the following: ( begin case declare end exception exit for goto if loop mod null pragma raise return select update while with << continue close current delete fetch lock insert open rollback savepoint set sql execute commit forall merge pipe purge The symbol " " was ignored.
Tables I work with are:
Artikal (sifra_artikla, naziv, aktuelna_cena),
Cena_artikla (sifra_artikla, datum_od, cena)
You will notice that this differs from the first problem, but my task is to implement the two optimization techniques and my base. Both techniques are quite similar and I hope that I now have enough information to help me. I suppose that when this problem is solved the othet one will too!
Thank in advance!

I need to interface SCC-TC02 with help of SC 2345 and PCI-6024E DAQ Card.please tell me the procedure and if possible send me the program

Similar Messages

Maybe you are looking for