I need urgent help with i tunes and my i phone 3 GS

I have just brought my own lap top and have installed i tunes.
because all the music on my i phone was all done on a friends lap top and
itunes i want to put it on my itunes from my i phone..
is this possible to do?? if so how do i put it from my i phone onto my itunes
without deleting all my music and applications??
Thanks heaps

First, authorize your new computer in itunes: Store>Authorize this computer.
Next, make sure that auto sync when an ipod/iphone is connected is "NOT CHECKED" in itunes>preferences.
Next, connect your phone, DO NOT SYNC!
Go up to file "Transfer purchases made on this ipod to this computer"
All of your purchased music & apps will then be transferred, music you ripped on your own won't, you'll have to restore that from a backup.
As for your contacts, before you sync make sure you have at least one contact in whatever program your computer uses for that purpose, outlook/address book.
At the prompt for merge or replace, select merge contacts.

Similar Messages

Need urgent help with HSDIO hardware timing

Hi everyone,
I need urgent help regarding HSDIO hardware timing. I've been working in a project which generating serial ramp using HSDIO pxie device.
I'm using clock rate 40MHz and generating 14 bit of boolean for each step of ramp. And I have to generate simply 256 steps ramp.
Which means, 256 (steps) x 14 (boolean array) x 25 ns (period of 1 boolean value) = 89,6 ns.
What I'm doing right now is with using index of FOR loop as my input data (converting the index into 14bit boolean), then write into pxie device in every iteration,
which means, my data is getting into output in every 1ms time, right? (I'm using windows)
And I want to be able to generate faster than that.
How can I prewrite my 256 steps ramp, then write them all at once into pxie device. I'm really stuck here.
In the picture can you see how I do the write into device in every iteration of FOR Loop.
Regards,
Yan.

hi, thanks for responding.
with using example of dynamic generation with script, I can manage to generate the ramp with controllable delay (generate the whole waveform, including delay with script command, then write to the card).
But I still have 1 question, I can test the output of the generation using oscilloscope and cant see the start delay (I'm writing delay at the start, before generating the ramp). My signal generated at 0 sec.
How can I check this start delay? is there any good example delivered with Labview to check this generation? Somehow I cant use the "dynamic generation and acquisition" example to see my generation (cant figure out how to capture the generated signal).
regards,
Yan.

Need urgent help with Ifs1.1 on Solaris

We have installed IFS 1.1 with Oracle 8.1.7 on a three tier System (two Suns). We use JWS as WebServer. When we start IFS and JWS everything seems to work fine. But after some time (irregulary) we are not able to contact the JSP-Sites via a bowser. After restarting JWS, everything works fine for some time.
Sometimes it happens (about one times a day), that the whole JWS crashes (JWS-Admin doesn't work). So we have to restart the whole IFS.
What can be the problem? We need urgent help, because the deadline for our project is Wednesday.
By the way:
Where do I have to start CTX on the IFS- or the Oracle-Side?
null

Yes, we tried the Oracle HTTP - Server, but we weren4t able to get it to work. We didn4t get our JSP-Files to work with it. But that is another issue. I think it4s not a problem of JWS, but IFS.
Additionally it is strange, that we are still able to connect to the database via SqlPlus.
IFS works fine for about 15 minutes, than it crashes, nothing works anymore. We found following errors in the IfsAgents.log:
maybe it can help?!
Mon Dec 04 23:12:20 CET 2000
Server STARTED: IfsAgents(19944) not managed
Attempting to load agent EventExchangerAgent
Agent EventExchangerAgent loaded
Server STARTED: IfsProtocols(19945) not managed
Attempting to start agent EventExchangerAgent
EventExchangerAgent: Start request
Agent EventExchangerAgent started
Attempting to load agent ExpirationAgent
Agent ExpirationAgent loaded
EventExchangerAgent: starting timer
Attempting to start agent ExpirationAgent
ExpirationAgent: Start request
Agent ExpirationAgent started
Attempting to load agent GarbageCollectionAgent
Agent GarbageCollectionAgent loaded
ExpirationAgent: computed initial delay (in ms) is: 10024504
ExpirationAgent: starting timer
Attempting to start agent GarbageCollectionAgent
GarbageCollectionAgent: Start request
Agent GarbageCollectionAgent started
Attempting to load agent ContentGarbageCollectionAgent
Agent ContentGarbageCollectionAgent loaded
GarbageCollectionAgent: computed initial delay (in ms) is: 11816890
GarbageCollectionAgent: starting timer
Attempting to start agent ContentGarbageCollectionAgent
ContentGarbageCollectionAgent: Start request
Agent ContentGarbageCollectionAgent started
Attempting to load agent DanglingObjectAVCleanupAgent
Agent DanglingObjectAVCleanupAgent loaded
ContentGarbageCollectionAgent: starting timer
Attempting to start agent DanglingObjectAVCleanupAgent
DanglingObjectAVCleanupAgent: Start request
Agent DanglingObjectAVCleanupAgent started
Attempting to load agent OutboxAgent
Agent OutboxAgent loaded
DanglingObjectAVCleanupAgent: computed initial delay (in ms) is: 5500105
DanglingObjectAVCleanupAgent: starting timer
Attempting to start agent OutboxAgent
OutboxAgent: Start request
Agent OutboxAgent started
Attempting to load agent ServiceWatchdogAgent
Agent ServiceWatchdogAgent loaded
OutboxAgent: Done processing
Attempting to start agent ServiceWatchdogAgent
ServiceWatchdogAgent: Start request
Agent ServiceWatchdogAgent started
Attempting to load agent QuotaAgent
Agent QuotaAgent loaded
ServiceWatchdogAgent: Initializing ServerWatchdogTable with 9 entries
ServiceWatchdogAgent: starting timer
Server STARTED: FtpServer(20082) managed by IfsProtocols(19945)
ServiceWatchdogAgent: New Server being watchdogged
Attempting to start agent QuotaAgent
QuotaAgent: Start request
Agent QuotaAgent started
QuotaAgent: starting timer
Server STARTED: CupServer(20124) managed by IfsProtocols(19945)
ServiceWatchdogAgent: New Server being watchdogged
Server STARTED: ImapServer(20130) managed by IfsProtocols(19945)
ServiceWatchdogAgent: New Server being watchdogged
Server STARTED: SmtpServer(20150) managed by IfsProtocols(19945)
ServiceWatchdogAgent: New Server being watchdogged
ServiceWatchdogAgent: Unlocked Server Detected in checkServer
ServiceWatchdogAgent: Unlocked Server Detected in checkServer
ServiceWatchdogAgent: Unlocked Server Detected in checkServer
ServiceWatchdogAgent: Unlocked Server Detected in checkServer
ServiceWatchdogAgent: Unlocked Server Detected in checkServer
ServiceWatchdogAgent: Unlocked Server Detected in checkServer
ServiceWatchdogAgent: Unlocked Server being investigated
ServiceWatchdogAgent: Unlocked Server being investigated
ServiceWatchdogAgent: Unlocked Server being investigated
ServiceWatchdogAgent: Unlocked Server being investigated
ServiceWatchdogAgent: Unlocked Server being investigated
ServiceWatchdogAgent: Unlocked Server being investigated
ServiceWatchdogAgent: Freeing unlocked server 19687
ServiceWatchdogAgent: Freeing unlocked server 19666
Server STOPPED: CupServer(19687) managed by IfsProtocols(19519)
ServiceWatchdogAgent: Freeing unlocked server 19723
ServiceWatchdogAgent: Freeing unlocked server 19520
Server STOPPED: FtpServer(19666) managed by IfsProtocols(19519)
Server STOPPED: SmtpServer(19723) managed by IfsProtocols(19519)
ServiceWatchdogAgent: Freeing unlocked server 19519
Server STOPPED: IfsAgents(19520) not managed
ServiceWatchdogAgent: Freeing unlocked server 19712
Server STOPPED: IfsProtocols(19519) not managed
Server STOPPED: ImapServer(19712) managed by IfsProtocols(19519)
ServiceWatchdogAgent: Freed Server removed from watchdog list
ServiceWatchdogAgent: Freed Server removed from watchdog list
ServiceWatchdogAgent: Freed Server removed from watchdog list
ServiceWatchdogAgent: Freed Server removed from watchdog list
ServiceWatchdogAgent: Freed Server removed from watchdog list
ServiceWatchdogAgent: Freed Server removed from watchdog list
QuotaAgent: Timer event: 0 active; 0 exceeded
ContentGarbageCollectionAgent: Freed 5 unreferenced ContentObjects
QuotaAgent: Timer event: 0 active; 0 exceeded
ServiceWatchdogAgent: IfsException publishing timer details:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-11012: Unable to get events from other services
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException in checkForDeadServices():
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException in handle loop; continuing:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException publishing timer details:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException publishing timer details:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException publishing timer details:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException publishing timer details:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
ServiceWatchdogAgent: IfsException publishing timer details:
ServiceWatchdogAgent: oracle.ifs.common.IfsException: IFS-10651: Unable to begin transaction
oracle.ifs.common.IfsException: IFS-10603: Unable to set database savepoint
java.sql.SQLException: ORA-03114: not connected to ORACLE
null

Hello I have a few questions and I need some help with my iTunes and iPod

Hello iTunes people.
I have a little problem with my iTunes. I actually almost know nothing about iTunes really. But I have had a 80 gig ipod .. ummm I think it's a iPod classic maybe. A long time ago I just downloaded iTunes. I think one of my tech friends already had put the program onto my PC so I did not even have to download it. Anyways I put my life's collection of mp3's onto iTunes and then syncs it with my iPod and it worked great. Here is my problem. I just recently bought a MONSTER PC. I have lovingly named it " ED209 " I downloaded iTunes for it and I have the most up to date version.8.1.1 is the most current version correct? Ok well here is my problem. What I want to do is I want to put everything that is currently on my iPod ONTO the iTunes library. I DO NOT want to import anything from the library or playlist or whatever you call it ONTO the iPod because there is nothing in the library. Now this is were its gets weird and possibly silly. A person I was chatting with on Facebook sort of made fun of me because she was like " Dude! Just push " Sync " But the reason I am paranoid is because THIS is the message I get....
" The iPod " Aaron's iPod " is synced with another iTunes library. Do you want to erase this ipod and sync with this iTunes library? "
HOLY COW!! That girl on Facebook was making fun of me but READ THAT. That exactly says ERASE the "iPod" and Sync with THIS library " It does not say put what is ON the iPod into THIS Library. It says it the other way around. Clear as day it says it will ERASE the " Ipod " it does not say " Fill the library with whats on your iPod "
Do I all of a sudden not understand English or something???? I know how to freaking read and from what it says is sounds a 100 percent like " we will ERASE youe iPod and put everything from this playist or library onto your iPiod" But there is NOTHING in my library? Am I mentally challenged or what?
I hope someone can help me here and I have another request. Could someone just tell me all the cool things I can do with iTunes and my iPod? I am trying to read the help files and the FAQ and whatever else Apple provides you with but it has SO MUCH crap that looks usless. I find myself reading a whole paragraph about some simple little section of s section of a section of a feature! Know what I mean. Someone give me the long and short of the neat things I can do with this stuff. I have windows Vista with a wicked computer that has like 6 gigs of ram and m iPod is a 80 GB Classic
help !!
PROTEUS

*What I want to do is I want to put everything that is currently on my iPod ONTO the iTunes library.*
1). Connect your iPod to your computer. When you get the message that it is linked to a different library and asking if you want to link to this one and replace all your songs etc, press "Cancel". Pressing "Erase and Sync" will irretrievably remove all the songs from your iPod.
2). When your iPod appears in the iTunes source list change the update setting to manual, that will let you continue to use your iPod without the risk of accidentally erasing it. Check the "manually manage music and videos" box in Summary then press the Apply button. Also when using most of the utilities listed below your iPod needs to be enabled for disc use, changing to manual update will do this by default: Managing content manually on iPod and iPhone
3). Once you are connected and your iPod is safely in manual mode there are a few things you can do to restore your iTunes from the iPod. iTunes will only let you copy your purchases directly from an iPod to the computer, you'll find details in this article: Copying iTunes Store purchases from your iPod or iPhone to a computer
For everything else (music from CDs, other downloads and including iTunes purchases) there are a number of third party utilities that you can use to retrieve the music files and playlists from your iPod. You'll find that they have varying degrees of functionality and some will transfer movies, videos, photos, podcasts and games as well. You can read reviews and comparisons of some of them here:
Wired News - Rescue Your Stranded Tunes
Comparison of iPod managers
A selection of iPod to iTunes utilities:
TuneJack Windows Only (iPhone and iPod Touch compatible)
SharePod Windows Only (iPhone and iPod Touch compatible)
iPod2PC Windows Only
iDump Windows Only
YamiPod Mac and Windows
iPod Music Liberator Mac & Windows
Floola Mac & Windows
iPodRip Mac & Windows (iPhone and iPod Touch compatible)
iPod Music Liberator Mac & Windows (iPhone and iPod Touch compatible)
Music Rescue Mac & Windows (iPhone and iPod Touch compatible)
iGadget Mac & Windows (iPhone and iPod Touch compatible)
iRepo Mac & Windows (iPhone and iPod Touch compatible)
iPod Access Mac & Windows (iPhone and iPod Touch compatible)
TouchCopy Mac & Windows (iPhone and iPod Touch compatible)
There's also a manual method of copying songs from your iPod to a Mac or PC. The procedure is a bit involved and won't recover playlists but if you're interested it's available on page 2 at this link: Copying Content from your iPod to your Computer - The Definitive Guide
4). Whichever of these retrieval methods you choose, keep your iPod in manual mode until you have reloaded your iTunes and you are happy with your playlists etc then it will be safe to return it auto-sync.
5). I would also advise that you get yourself an external hard drive and back your stuff up, relying on an iPod as your sole backup is not a good idea and external drives are comparatively inexpensive these days, you can get loads of storage for a reasonable outlay: Back up your iTunes library by copying to an external hard drive

Need urgent help with exporting movie

I have a simple 7-minute project on FCP 7 that consists of still images from the internet and hand drawn images with a few animated elements.
It has only one audio track and two video tracks. I am using PAL DV size format. I am in the UK.
I exported it using quicktime conversion with H264 compression and good quality and the final file size was 125MB.
My urgent problem is that I need to upload this file to a university website for an online course in two days, and their file size limit is 50 MB.
I need to make sure that the teacher can play the file, and I need to get it down to a smaller file size for uploading.
I have tried all sorts of exporting from FCP. I tried avi, m4v (the setting said ipod and it produced the m4v file), and quicktime mov at different sizes like 1/4vga size. The best file size was 29 mb for the m4v ipod export, and 98mb for the qt mov file exported at medium quality. The avi file grew to 1.2gb!
I don't know if the m4v file is playable on the system that the teacher uses (she is on a windows computer).
Can anyone please give me some specific advice on how to create a smaller video file that is more universally compatible?
I have access to all of the FCP 7 suite and the Adobe CS6 suite which includes Premiere Pro, Prelude and Adobe Media encoder, if that helps.
Thanks a lot for any advice.

Jonathan Rooper wrote:
Hi Luis
The advice you've been given is good for helping you to get a good quality video at a reasonable file size.
But it may be worth thinking more about which format will certainly play on your teacher's PC. The most likely player on any PC is Windows Media Player, which tens to be installed by default.
The most likely video to be viewed on a PC is one from YouTube... andH.264 is supported on all "modern" PCs. QuickTime Player is free and very available.
A disadvantage for Mac users is that yoou'll ned the Flip4Mac plugin to create WMV movies. I think the cheapest paid version of Flip4Mac costs around £30.
All you need on a Mac fis the free Flip4Mac player.
If you get that, and choose the web high I quality setting, you should have a file within 50MB that plays reliably and looks OK. (A cheaper way of doing this, if you have access to a PC, is to use the free Windows Media Encoder).
Best of luck
Jonathan

Need urgent help with database startup

dear all,
i am using oracle 10g on windower server 32 bit.
i try to startup my database today, and it give me error, and it is my production database,
i need very urgent help from you.(i have no rman backup , and the data is not so necessory, since it is for student practice.)
SQL> startup open
ORACLE instance started.
Total System Global Area 524288000 bytes
Fixed Size                   790180 bytes
Variable Size             250343772 bytes
Database Buffers          272629760 bytes
Redo Buffers                 524288 bytes
Database mounted.
ORA-01110: data file 34: 'G:\ORACLE\DATAFILES_ACADEMY\ACADEMY'
ORA-01115: IO error reading block from file 34 (block # 1)
ORA-27070: async read/write failed
OSD-04016: Error queuing an asynchronous I/O request.
O/S-Error: (OS 23) Data error (cyclic redundancy check).regards.

Maahjoor wrote:
Hi dears,
i need further assistance from your side, i have restarted the server, but the same problem.
as there a way to drop and re-create a system tablespace? since the file 34 belong to system tablesapce.
regardsNo.
So just create a new database. That will take all of ten minutes. And tell your students to create new tablespaces. That will take them two minutes.

Need urgent help with the query - Beginer

Hello - I need help with a query to populate data in a table.Here is the scenario.
Source1
MnthID BranchCod CustID SegCode FXStatus ProfStatus Profit
200712 B1 C1 20 Y Y 100
Source2
MnthID BranchCod CustID ProdCode ProdIndex
200712 B1 C1 12 1
200712 B1 C2 12 0
Destination
MnthID BranchCod SegCode ProdCode CountSegCust CountProdCust ProfitProdCust
Condition and Calculations:
1)Source1 customer are base customers.If Source2 has customers who is not in source1 then that customer's record should not be fetched.
2)SegCode, FX Status, ProfStatus is one variable in destination table. [ SegCode = SegCode+ FXStatus (if FXStatus = Y)+ ProfStatus (if FXStatus = Y) ]
3)CountSegCust = CountCustID Groupby MnthID,BranchCod,SegCode Only.
4)CountProdCust = CountCustID Groupby MnthID,BranchCod,SegCode,ProdCode (when ProdIndex = 1)
5)ProfitProdCust = Sum of Profit of Customers Groupby MnthID,BranchCod,SegCode,ProdCode (when ProdIndex = 1)
Apologies for bad formatting.
Thanks in advance!!

A total guess indeed.
It's not clear whether some aggregation can be done (summing counts of grouped data might cause some customers being counted more than once)
insert into destination
select mnthid,branchcod,segcode,prodcode,countsegcust,countprodcust,profitprodcust
from (select s1.mnthid,
               s1.branchcod,
               s1.segcode || case s1.fxstatus when 'Y' then s1.fxstatus || s1.profstatus end segcode,
               s2.prodcode,
               count(s1.custid) over (partition by s1.mnthid,
                                                   s1.branchcod,
                                                   s1.segcode || case s1.fxstatus when 'Y' then s1.fxstatus || s1.profstatus end
                                          order by null
                                     ) countsegcust,
               count(case proindex when 1
                                   then custid
                     end
                    ) over (partition by s1.mnthid,
                                         s1.branchcod,
                                         s1.segcode || case s1.fxstatus when 'Y' then s1.fxstatus || s1.profstatus end
                                         s2.prodcode
                                order by null
                           ) countprodcust,
               sum(case proindex when 1
                                 then profit
                   end
                  ) over (partition by s1.mnthid,
                                       s1.branchcod,
                                       s1.segcode || case s1.fxstatus when 'Y' then s1.fxstatus || s1.profstatus end
                                       s2.prodcode
                              order by null
                         ) profitprodcust,
               row_number() over (partition by s1.mnthid,
                                               s1.branchcod,
                                               s1.segcode || case s1.fxstatus when 'Y' then s1.fxstatus || s1.profstatus end
                                               s2.prodcode
                                      order by null
                                 ) the_row
          from source1 s1,source2 s2
         where s1.mnthid = s2.mnthid
           and s1.branchcod = s2.branchcod
           and s1.custid = s2.custid
where the_row = 1Regards
Etbin

Need urgent help with communicating with the HP 4155B analyser with Labview

i folks,
I'm currently trying to communicate with our HP 4155B semiconductor pamaremter analyser. I do not have experience with GPIB yet. I have installed the NI VISA.
I was wondering if anyone could help with getting me started on how to start communicating with the device using Labview.
I'm not certain where to start.
Kind regards
Rob

Hi,
Thanks for the help. I now have communication with the instrument.
I was wondering if it's possible to to setup a data measurement (I-V Sweep) and be able to read the measurement data in realtime as it is being measured. So I basically see the graph updating itself on the PC during the measurement.
Is this possible? Could anyone give advice on how I can go about this or are there any examples that can help me understand how to do this?
I'm not completely sure how to initialise the instruemnt for communication and handle VISA WRITEs and READs. within LabView
Best regards
Rob

Need Urgent Help with Apache and PHP

I have been struggling with apache and php for a week now and I finally broke down to post a message.
I have apache 1.3 running on my mac mini g4 with 10.4.9 and I installed sql. I went to the entropy website and downloaded php5 to install without knowing I already had php4 on the machine. I installed 5 but could not get it to work. I then went back to httpd.conf and tried to install php4 by uncommenting out the loadmodule and addmodule lines. I restarted apache but php still did not work. I tested the phpinfo.php script but all I got was the script in Safari and not the actual page. At the moment, I have php4 and php5 on my machine but can't get either one to work. I am sure there is an easy fix but I don't know it. Please help.

The problem is not terribly complicated, but Apache will not start with the entropy file in the folder
/etc/httpd/users/
Let me experiment on you. Rename the entropy file and then try to start Apache. To do this, open Terminal and paste this command:
<pre>sudo mv /etc/httpd/users/+entropy.conf /etc/httpd/users/+entropy<pre>
Now check the Apache configuration:
<pre>apachectl configtest<pre>
If it says "Syntax OK", start Apache:
<pre>sudo apachectl start<pre>
Since we only disabled the entropy file, you should be able to enable PHP5 with some more advanced configuring.

Need urgent help with service and file removal

Hi,
I need a powershell script that would stop a windows service ,wait for 2 mins, delete a particular file from C:\documents&settings and then start the service again.Is this possible ?
Thanks

Thanks for the reply chen. May be i was not clear in my query
I plan this because a particular file of configmgr is corrupt on workstations. So the service has to be stopped first before the deletion. I need to run this on many computers remotely. The import file will have the machines that need the script to be run.
The script has to run all the four steps on the machines based on the import file and export to a file with the results.How can i modify ?
The sequence will be as follows
Stop-Service -Name BITS -Verbose
Start-Sleep -Seconds 120
Remove-Item -Path C:\documents&settings\***** -Force -Verbose
Start-Service -Name BITS -Verbose
Regards
Sd

I need urgent help with my macbook pro, installed a theme and now unable to open windows, please help !

Hello,
I installed a theme on OS X Lion that was actually made for snow leapor, because on a youtube video someone said it works with Lion too,
After installing it I got problems seeing close and minize icons.
And After reinstalling my Macbook pro, I am unable to open finder, Safari, Terminal etc.
I have tried to get help from several help forums, and tried changing files as described here
https://discussions.apple.com/thread/3256533?start=0&tstart=0
Theme was downloaded from here
http://www.fif7y.com/themes/sog/

Okay, it's both for your first question: When I import the songs to the library, the songs are not in the correct order as they were on the CD. And, in the process of my importing the songs, the library scrambles the songs in different sections of the library (I explain further below)
I don't know what you mean by "little triangle" pointing up or down. What's that got to do with the price of fish in China? lol
When I get the music in the library the songs come out sorted this way: 2 songs from CD 1 appear one section of the library, then 1 song from CD 2 appears in the next column, along with the album work. Then, I go down farther, and there's a few more of the songs from CD 1 in the next section. I go down again, and maybe 2 or 3 songs are in that column. Along with the artwork for that CD. Then I scroll down again in the library, and there's maybe 3 or 4 songs from CD 1 there. Get the picture? It keeps sorting the songs in that order. And yes, the CDs I was importing were compliation dance CDs, along with some from the same artist, like Barry Manilow.
I hope I answered the questions better so that you can help me Thanks in advance, Glenn

Need urgent help with RAID failure on Graphics server (running OSX10)

Hey.
Here's the deal... Our graphics department has a MAC G4 (fully upgraded. newest patches, OS, etc.) that's got a 4 port SATA RAID controller. They use this with four 750GB hard drives as an external RAID (the OS is on a seperate, 65GB hard drive). The way it's set up, through Apple's OS, is we have the four 750GBs in pairs... those pairs are striped, and then the two sets of striped 750s are mirrored. This has worked just fine for a number of months, but we recently had a power surge, and now we're unable to mount "Monkey" (the name of the 1.4TB array).
See the below screenshots for more clarification.
http://www.amcdoors.com/lorenzo/raidsetup.JPG
This shows the RAID card, and the four SATA cables coming out of it.
http://www.amcdoors.com/lorenzo/leftside1.JPG
As you can see in this and the below screenshots, this shows the 1.4TB Striped set as 'online', but the two below (the two 750GB hard drives) show up as "offline".
http://www.amcdoors.com/lorenzo/leftside2.JPG
this shows the actual drive i click on. same thing
http://www.amcdoors.com/lorenzo/leftside3a.JPG
If i click the entire array, you can see how it's set up (the Mirrored RAID set consisting of the two Striped RAID sets). The RAID sets (all 3 of them) are showing up as online, yet the drives are offline. No idea why. The drives are all powered, and are spinning, and plugged in.
http://www.amcdoors.com/lorenzo/leftside3b.JPG
when you click "Monkey Drive", nothing shows up in it. i don't remember if anything ever used to. if you click 'mount', nothing happens.
http://www.amcdoors.com/lorenzo/leftside4.JPG
http://www.amcdoors.com/lorenzo/leftside5.JPG
this shows the exact same problem as the first RAID set.
http://www.amcdoors.com/lorenzo/verifyRAIDset1.JPG
If you try to Verify the RAID set, it shows that no repairs are necessary
http://www.amcdoors.com/lorenzo/verifymonkey.JPG
If you try to verify Monkey, you get a "Volume Needs Repair" error... but when you try to repair it, you get this:
http://www.amcdoors.com/lorenzo/repairmonkey.JPG
Really need help; this is a pretty critical problem. Someone that's familar with RAID solutions on MACs please help me out. We can't risk losing any data if at all possible.
Thanks
~Lorenzo

You might want to post this to the Server Products forums.

Alright I give! I need some help with groups/busses and more please..

Hi all,
Well, its now been a few weeks of my off and on testing with my new Logic Rig, I have every plug I can transfer over to UB that I can and now am trying to get deeper into things.
First I struggled with learning the environment (I still dont get it fully) but now I am really confused about group and fx tracks.
- Am I missing something or is everything just a buss turned into a group? This also included creating an FX track?
If this is the case then its not nearly as complex as I think it is but I cant figure certain things out with the way logic handles naming in regards to its busses.
Lets say I want to create a sidechain group. I take an audio track change it to represent buss (1), I then rename buss 1 to SC-GROUP, now any window that I drop down to find the newly names SC-GROUP always remains named as buss (1). This even happens when I rename the buss direct from the audio environment.
I must be missing something, whats been confusing the heck out of me is that no matter how I try and name things they always remain their original names in any menues as the example of the buss (1), so how do I rename these channels so I can clearly know exactly where I am routing audio?
So lets summarise where I am lost so far hehe.
1. Are groups really just empty busses renamed to act as a group?
2. How can I rename a buss/group and be able to see the renamed channel in the menues.
and for the 3rd new question of sorts...
3. FX Sends, again is this just a buss that has an AU inserted into its channel and then rout the insert of an additional audio channel to the buss with the FX inserted?
and now my last uestion of the day if I have not confused you to death so far
Why is it that when I add a AU lets say battery as instrument 1, when I add another in the window and I rerout an instrum,ent track the next AU shows up at the bottom of the list instead of inst. 2?
If I am not explaining myself clearly enough for any of my examples let me know so I can try to better represent my questions. I am still so new to Logic and still have yet to get the bulk of the simple operations down just yet..
Thanks again for all your asistance!

Thank you guys,
So if I understand right, a sub buss is nothing more than a routing the output of a few channels to a buss to control a few aspects like I had mentioned compressing an entire group of tracks EG: a drum buss (in this situation a drum sub buss?).
So I will have to reffer to the manual again to read the details on an actual group since it does seem there is a difference EG: the group can actually manipulate the faders of channels routed to the group?
FX busses seem to be just that, slap an FX info either and AUX channel or a buss and then set the insert of that AUX or buss desired.
The reason I asked about naming is that lets say I have 6 effects tracks I wish to use lets say as an example AUX1=Short Delay, AUX2=Long Filter Delay, AUX3=Slap Verb, AUX4=Long Verb and so forth.
When I go to actually use these inserts I need to assume I know exactly what AUX I assigned each effect to, if I could simply rename this AUX track to refference the effect it would make so much more sense then trying to remember what AUX5 was.
In regards to my last question here is a bit more of a detailed explanation, please bare with me as I am not in front of my computer.
1. I add battery into Audio Instrument-1
2. I then configure my environemt to use my AUXs I already have inplace for audio routing.
3. I then edit the Audio window create the midi for a new multi-instrument.
4. I come back to the main arrange window and hold-click on the next available audio-instrument and in the instrument window battery will be instrument 1 out of how ever many blanks apear EG:25+
5. Now I go to add lets say Stylus RMX into the next available mutli audio instrument. I then repeat steps 2,3,4.
Now when I get to step 4 this time instead of audio instrument 2 from the lint being Stylus it shows up as the last possible instrument in the drop list that appears under audio instrument from hold-click on the audio-instrument track.
Its just odd, it should be instrument 2, but instead it shows up as the last possible choice.
Maybe I am doing something wrong, even sometimes when I grab on of batteries midi tracks and create next object I will get a random audio track in there out of no where, or maybe its just a bug with battery.
Any ideas? If I still am not describing this right, I will post a step by step this eve of exactly the steps I am taking.
Thanks again, this forum has been very helpful in getting me going with the questions I just cant seem to get around from my Nuendo work flow.
Cheers!

Need Urgent Help With Getting Intl Service from Bangkok

Before I arrived in Bangkok, I spoke with Verizon CS from the US because I needed Intl Service on my Iphone 4. My boyfriend has an Iphone 5 and was able to add a calling plan in 5 minutes of calling Verizon CS. I then called Verizon CS, and was told that my Iphone 4 cannot be used in Thailand. I told the CS Rep that my boyfriend just added the service on his Iphone 5, and did the same on a trip to Thailand last year with an Iphone 4. She told me that with an Iphone 5 he also cannot use the service in Thailand without a Sim Card or Global Phone? I then put him on the phone with her, and they spoke for ten minutes about this before my plane departed.
I have been in Bangkok since 04MAR14 trying to reach Verizon by web, Instant Chat, phone, and even called Verizon 611 from my boyfriend's handset. he call Failed! He then gave me this number to call Verizon Global Support: 908-559-4899. I have called this number numerous times from the hotel. The recording does not recognize when I "Press 1" or "Press 2", and proceeded to hang up on me several times. Is there no human at Verizon that help me????? I have spent approx 3 hours now trying to contact Verizon since 04MAR14. I am supposed to be enjoying my vacation here. Can someone please address these questions immediately?
1. Am I currently being charged to use WIFI in Thailand?
2. I transited Tokyo on 03MAR, and tried to call Verizon Support from my Handset, which Failed. Am I being charged for that?
3. What message do my contacts receive when they text me in the US?
4. Can I activate message response to contacts in the US now telling them that I am out of the country until the evening of 11MAR14?
Please help me, I am extremely frustrated, as I desparately want Phone service here in Thailand, and I am transiting back to Tokyo on 10MAR14, arriving there at 245pm, and I will need Phone service there as well.
Sincerely,
Nancy
Private info removed as required by the Terms of Service.
Message was edited by: Admin Moderator

I'm so sorry you haven't been able to get any service while traveling NancyStuckInThaiWithNoService, as well as for not being able to get a hold of anyone to assist you. I'm happy to answer your questions here. As you mentioned, the iPhone 4 is not a Global phone. Therefore, you can only use on a CDMA network, (not GSM). Thailand is GSM/Global, Japan/Tokyo is CDMA; therefore, you can use phone there. (It could be settings were not set correctly to use in Tokyo.
1. If you're using WiFi, there is no charge. Its best to turn Mobile Data off in Settings to avoid any International charges.
2. Japan/Tokyo calls are $1.99/minute. However, if trying to reach Global Support, you will not be charged.
3. Your contacts don't receive any notification when they text you. They may get some alert days later, that the message was not received by you/ or it has been timed out, but it won't say why.
4. If you're able to use another phone, and call your mobile number, you can press # when you hear your voice mail greeting, enter password, then # again, to change personal greeting. You're able to update greeting with notification that you're traveling.
** When back in Tokyo, you can go to Settings & make sure Airplane Mode is OFF. Also, you can go to General, (from Settings),> Network> Cellular Data- ON> Data Roaming- ON.***
Here are rates while in Japan/Tokyo http://vz.to/18TRKVE
Lastly, it may be easier to reach us on Facebook at Verizon Wireless, or on Twitter at @VZWSupport
Thank you,
VanessaS_VZW
Follow us on Twitter @VZWSupport

URGENT - Help with my ipod and itunes not connection due to code

Hi there,
I have an ipod touch which I updated to ios4 last week, go away on holiday with it and within 2 days its showing on the screen that it needs to be connected to itunes.
So I come home and do just that but now itunes tells me that it cant connect to my touch due to me having a security code on it... only thing is I cant put the code in as its asking to be reset and connected to itunes but I cant do that as itunes is asking for the code to be put in!!!!
What do I do???

Can anyone help me - please.... I still have the receipt for the ipod and I have all the other bits that come with it so if onlly someone could give me some hints on what I should do... my 4 yo is driving me mad now he can't have his daily dose of fishtank fun!!!

I need urgent help with i tunes and my i phone 3 GS

Similar Messages

Maybe you are looking for