I phone 5 used 80% of my data in 27 mins was not even on phone

Any advise on this please

I was just on the phone with AT & T and they said it is a problem that Apple knows about with the 5s. They said it is a one time surge??? My daughters has done the same thing

Similar Messages

HT201299 After installing an app on iPhone 5s, I can't use it outside of wifi (using cellular or mobile data) and the app is not listed in settings to enable its use of mobile data - any clues on what is wrong here?

After installing an app on iPhone 5s, I can't use it outside of wifi (using cellular or mobile data) and the app is not listed in settings to enable its use of mobile data - any clues on what is wrong here?

Steps to take to resolve this issue:
1/ Turn off Wifi
2/ Ensure Mobile (cellular) data is on
3/ Turn iPhone OFF and then ON (re-boot iPhone)
4/ Without turning Wifi on, open an app that requires mobile (cellular) data.
5/ The app will now show on the Settings list with the option to enable or disable mobile (cellular) data
6/ In time all apps that require or use mobile data will be added to the list automatically.

Virtex6:Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings

Hello，everyone.
I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
I download .bit file to FPGA and succeed.
When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
and the process is about 68% it fails.
The message below the IMapct is as belows:
done.
PROGRESS_END - End Operation.
Elapsed time =      0 sec.
// *** BATCH CMD : identifyMPM
// *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
'1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
done.
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
INFO:iMPACT - Current time: 2014/3/13 8:48:14
// *** BATCH CMD : Program -p 1
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': Programming device...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time =     23 sec.
Selected part: XCF128X
// *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
// *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
INFO:iMPACT - Current time: 2014/3/13 8:49:32
// *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
'1': Downloading core...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:2492 - '1': Completed downloading core to device.
Current cable speed is set to 6.000 Mhz.
Cable speed is default to 3Mhz or lower for BPI operations.
Current cable speed is set to 3.000 Mhz.
Setting Flash Control Pins ...
Setting Configuration Register ...
Populating BPI common flash interface ...
Common Flash Interface Information Query completed successfully.
INFO:iMPACT - Common Flash Interface Information from Device:
INFO:iMPACT - Verification string: 51 52 59
INFO:iMPACT - Manufacturer ID:        49
INFO:iMPACT - Vendor ID:             01
INFO:iMPACT - Device Code:           18
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x008CE03B.
done.
'1': Erasure completed successfully.
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
Setting Flash Control Pins ...
'1': Flash Programming completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Reading device contents...
done.
'1': Verification completed.
Setting Flash Control Pins ...
Current cable speed is resumed to 6.000 Mhz.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
`Elapsed time =    814 sec.
and i find many people have met the same thing. But they are spartan series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
I have read the status Registers and find there is an over-temperature state
and in Impact i could not readback the registers. It is strange.
I am anxious about this problem and have not solved it yet
What reasons may it be?
Hope for your answer, thank you

Hi~I want to know if you solve the configuration problem for virtex-6?
As I encounter the  same configuration problem, I want to consult  you with some question.
Can I have your email?
gszakacs wrote:
I have measured the VCCINT and find it is 1.0V, not 2.997V;
That is not at all surprising. I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
my Reference board is ML605
That would have been nice to know at the beginning...
It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide. See table 1-27, table 1-33 and the note below it about switch S1.
I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA. Have you tried power-cycling to see if the FPGA boots from the flash?
I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that). That will not only show the bits of the configuration status register, but also describe what each bit means. Among other things you can check the state of the FPGA's configuration logic and the Mode pins.

Configuration data download to FPGA was not successful.

I have designed a board with the Spartan 6 LX9 TQFP144 Package.
I am able to load a bitstream to the device with the digilent HS-2. However the fpga can not selfconfigure from
the attached SPI Flash.
Here is the console output from iMPACT:
GUI --- Auto connect to cable...
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: found 1 device(s).
INFO:iMPACT - Digilent Plugin: opening device: "JtagHs2", SN:210249983579
INFO:iMPACT - Digilent Plugin: User Name: JtagHs2
INFO:iMPACT - Digilent Plugin: Product Name: Digilent JTAG-HS2
INFO:iMPACT - Digilent Plugin: Serial Number: 210249983579
INFO:iMPACT - Digilent Plugin: Product ID: 30900152
INFO:iMPACT - Digilent Plugin: Firmware Version: 0109
INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 10000000 Hz
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 27.07.2015 16:19:26
PROGRESS_START - Starting Operation.
Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc6slx9, Version : 2
INFO:iMPACT:1777 -
Reading C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9.bsd...
INFO:iMPACT:501 - '1': Added Device xc6slx9 successfully.
done.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Selected part: N25Q128
Unprotect sectors: FALSE
INFO:iMPACT - Current time: 27.07.2015 16:20:19
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': SPI access core not detected. SPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9_spi.cor.
'1': Downloading core...
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
'1': Reading status register contents...
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1100 1110 1100
INFO:iMPACT:2492 - '1': Completed downloading core to device.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': Erasing Device.
'1': Using Sector Erase.
'1': Programming Flash.
'1': Reading device contents...
done.
'1': Verification completed.
'1':Programming in x4 mode.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
INFO:iMPACT - '1': Flash was not programmed successfully.
PROGRESS_END - End Operation.
Elapsed time = 78 sec.
If i read that correctly Data was written to the Flash but the fpga was not able to configure from that data.
Done-pin is connected to 3.3V via a 470 Ohms Resisor.
The Flash is a N25Q128A13ESE40G, Datasheet here: http://www.farnell.com/datasheets/1674445.pdf
I can perform a readback, checksum and an erase.
If i do a read device status this is the console output:
INFO:iMPACT - Current time: 27.07.2015 16:36:27
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
INFO:iMPACT - '1': Reloading FPGA configuration data stored in flash...
INFO:iMPACT:182 - done.
On the Flash side I have pulled s# and Hold up to 3.3V with 100k Resistors.
Can someone help me to find the problem?

So does the FPGA try to read the SPI flash when it boots ?
out with scope, probe the clock and the data , see if you can see it streamig out when you boot.
If so, then one other thing I see wrong a few times is data path of the SPI, single bit or 4 bits of data.
you have to make certain the bit file was created in the same width as the fgpa is expecting,
In ISE I think its in Impact where you make the SPI flash file and specify this .

Data of preceding document was not transmitted

HI,
data of preceding document was not transmitted
Im getting the above error i have created SO with respect to Project and Creating Delivery from project in CNS0
While creating delivery for project im getting the error
I have copied Delivery Type from LP to XXXX
When im using delivery type LP and while creating Project delivery that there is no above error but status is not getting change that is Delivery is Open which should be "Delivery Completed" after PGI
Pls Suggest
Thank you,
Regards,
Naveen

SPRO - Logistics General - Handling Unit Management - Materials Management - HU Requirement for Storage Locations and Default Values for Deliveries.
Select the plant and go to the storage location.
Enter the Sales org, Distribution channel, Shipping point, Vendor and Customer.
So then the entry which you create through inventory management will create using this customer for outbound delivery and vendor for inbound delivery, if there is none specified.
Now you can use MB1B to create the delivery for 311 movement type.

V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"

Hello，everyone.
I am using virtex5 XC5VLX155 FPGA and trying to download mcs file to BPI flash and have failed.
The flash is JS28F512P30E. The iMpact version is 14.7.
FPGA's VCCINT is 1.0V, VCCAUX is 2.5V. VCCO is 3.3V.
M[2:0] is 010 in Master BPI. Ican program FPGA through JTAG. The FPGA_DONE pin 's LED can always flash.
The error is shown as below. the full IMPACT console log and the SCHEMATIC_ FLASH are in the attachment.
Using x16 mode ...
Setting Flash Control Pins ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x004E4AFF.
done.
'1': Erasure completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
'1': Flash Programming completed successfully.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
PROGRESS_END - End Operation.
Elapsed time = 692 sec.
Hope everyone give more advices. Thank you.

Thank you very much!
I can read ack the mcs file, but the file is much bigger than the original mcs file.
The flash datasheet is in the attachment.
I want to use the Master BPI mode. In BPI_UP, the address starts at 0 and increments by 1 until the DONE pin is
asserted. I do not know the difference between the BPI_UP and BPI_DOWN.
ps: The R61,R62 and R63 are not weld on the board. The ADV pin is tie to VSS .

I have an ipad mini. From one moment to another a document that was created and used on pages app ( on the ipad mini) does not want to open ( When pressed it states " document cant be opened). How can I make this document open again?

I have an ipad mini. From one moment to another a document that was created and used on pages app ( on the ipad mini) does not want to open ( When pressed it states " document cant be opened). How can I make this document open again?
I have tried back ups and restoring, resetting, and even updating the pages app. And nothing has worked.

I have an ipad mini. From one moment to another a document that was created and used on pages app ( on the ipad mini) does not want to open ( When pressed it states " document cant be opened). How can I make this document open again?
I have tried back ups and restoring, resetting, and even updating the pages app. And nothing has worked.

I bought a used ipod touch. The music on it was not my taste. I found a delete feature and now EVERYTHING is gone. No icons. Nothing. How do I get it back?

I bought a used ipod touch. The music on it was not my taste. I found a delete feature and EVERYTHING is gone. How do I get the icons back and start over?

If you did not yet connect with iTunes, you can place any music from your library back into your iPod from the computer. When set to automatically manage usic and videos, whatever iTunes finds changed in your music app will be reset to what is on your computer iTunes library.

My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen

My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen.
I have tried with a wired USB keyboard and mouse using a single screen. Powered up with option pressed. No change.
Reset SMC no change

Run the Apple hardware test to see what it tells you. Run the extended test when prompted, which can take awhile.

After ejecting a disk plugged into the USB port using Finder, I am now getting "The disk was not properly ejected" message. This didn't used to happen. How can this be corrected?

After ejecting a disk plugged into the USB port using Finder, I am now getting "The disk was not properly ejected" message. This didn't used to happen. How can this be corrected?

When you right (control) click on the disk and click eject "disk name", do you pull it immeadiatly or wait a few seconds for it to unmount? Try waiting and see if you get the same message. If you do, when the disk is connected go to applications/utilities/disk utility, after opening DU, select the volume in question from the left side bar and try a permissions repair, you may also run verify disk and see if it comes up with any errors (they will be in red)

My iphone 5s got stolen and the option to erase data after 10 tries was not enabled. What happens after the incorrect password is input after 10 times?

my iphone 5s got stolen and the option to erase data after 10 tries was not enabled. What happens after the incorrect password is input after 10 times?

After the sixth erroneous passcode entry a delay is imposed that increases exponentially and eventually reaches over 40 years before another attempt can be made.
No one yet knows how long the next delay is.

Using a Variable in SSIS - Error - "Command text was not set for the command object.".

Hi All,
I am using a OLE DB Source in my dataflow component and want to select SQL Query from the master table I have created variables v_Archivequery
String packageLevel (to store the query).
<Variable Name="V_Archivequery" DataType="String">
     SELECT a.*, b.BBxKey as Archive_BBxKey, b.RowChecksum as Archive_RowChecksum
     FROM dbo.ImportBBxFbcci a LEFT OUTER JOIN Archive.dbo.ArchiveBBxFbcci b
     ON (SUBSTRING(a.Col001,1,4) + SUBSTRING(a.Col002,1,10)) = b.BBxKey
     Where (b.LatestVersion = 1 OR b.LatestVersion IS NULL)
    </Variable>
I am assigning this query to the v_Archivequery variable, "SELECT a.*, b.BBxKey as Archive_BBxKey, b.RowChecksum as Archive_RowChecksum
FROM dbo.ImportBBxFbcci a LEFT OUTER JOIN Archive.dbo.ArchiveBBxFbcci b
ON (SUBSTRING(a.Col001,1,4) + SUBSTRING(a.Col002,1,10)) = b.BBxKey
Where (b.LatestVersion = 1 OR b.LatestVersion IS NULL)"
Now in the OLE Db source, I have selected as Sql Command from Variable, and I am getting the variable, v_Archivequery .
But when I am generating the package and when running I am getting bewlo errror
Error at Data Flow Task [OLE DB Source [1]]: An OLE DB error has occurred. Error code: 0x80040E0C.
An OLE DB record is available. Source: "Microsoft SQL Native Client" Hresult: 0x80040E0C Description: "Command text was not set for the command object.".
Can Someone guide me whr am going wrong?
Please let me know where am going wrong?
Thanks in advance.
Thankx & regards, Vipin jha MCP

What happens if you hit Preview button in OLE DB Source Editor? Also you can use the same query by selecting SQL Command option and test.
Could you try set the Delay Validation = True at Package and re-run ?
If set the query in variable expression (not in value), then Set Evaluate As Expression = True.
-Vaibhav Chaudhari

Data type Timestamp(6) was not imported

OWB 10.1.0.4:
Importing data type timestamp causes skipping of importing those columns:
+ Table
+ mytable........ : Reconciled with Second Class Object Failure
+ Columns
+ col_timestamp_a .............. : Skipped (unsupported datatype)
+ a_cvarchar2_col ............... : Unchanged
+ col_timestamp_b.......... : Skipped (unsupported datatype)
I coud not find any entries in the whole discussion forum and the owb help gave me no answer to that.
Any idea ?
Message was edited by:
user590457

Hi,
Oracle Warehouse Builder doesnot support Timestamp datatype.
It supports only default datatypes.
We can solve this by creating a view for that table. In that, convert the timestamp datatype to Date datatype.
Regards,
Gowtham Sen.

How to use B540P HDMI in? Lenovo tech support was not helpful

I just bought a B540P all in one which has HDMI in/out connections. However there is no description in user manual on how to use it. I was hoping to connect an old desktop computer to the HDMI in, and use the all in one as an LCD monitor for my old desktop. Is this doable? How? I assume with the HDMI in, I can connect it with any HDMI sources, such as a DVD player or a game machine. Can anyone help me?
I called Lenovo tech support line, and got no help from them. Basically they have no idea, and told me this is the first time they heard of this question.

hi puffercow,
Thanks for posting and welcome to the community.
I really sorry to hear that our supprt team has not been as helpful as we do expect better from our support centres. I'll see what I can do to address this situation to ensure the the support teams are equipped for the future.
However regards to your issues the B540 is equipped to have the HDMI to either use it as and internal or external source. What you need to to do is ensure that your desktop is connected with the HDMI cable and connect it to the HDMI-IN input on the back of the B540P. Powerup the the B540P as well as your Desktop. Once the B540P is loaded, you will then need to switch the display. (See illustration below)
If you not notice on the B540p, on the left there is a symbol with arrows circling each other. (Described in red cicle above). press that to flip the view from the B540p desktop and your connected to HDMI desktop.
hope this helps and please do post your results.
regards

When I use paint bucket or brushes there is no colour not even black

I have recently installed Elements 9.0. I previously had 8.0 and no problems. If I try to darken skies with a black paintbrush it's all pale and so is my brush icon. I tried picking bright colours but they don't work, and I tried with the paint bucket and that's the same - no colour. Can anyone help?

Thank you - I've just been on and it is already in RGB. I'm quite
bewildered.
In a message dated 29/01/2011 09:31:02 GMT Standard Time, [email protected]
writes:
Your document may be in the grayscale color mode.
Go to Image >Mode and select RGB Color.
MTSTUNER

I phone 5 used 80% of my data in 27 mins was not even on phone

Similar Messages

Maybe you are looking for