I phone 6 unable to switch on

Hi
My i phone 6 is unable to switch on many times I tried to switch on but no any response..
my is I phone is 2 months old still in replaceme warranty...

If you are sure the device is charged, then try a reset. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. The phone should reboot. This can take up to 15 seconds or longer.

Similar Messages

  • NOKIA 7610 PHONE UNABLE TO SWITCH ON

    MY NOKIA 7610IS NOT SWITCHING ON. PLEASE HELP ME TO FIND A SOLUTION.

    Remove battery for 5 minutes & put it back and check. Check your battery if still operational, accepting charge.
    Message Edited by android on 01-Nov-2008 01:24 PM
    Knowledge not shared is knowledge wasted!
    If you find it helpfull, it's not hard to click the STAR..

  • HT1349 i am unable to switch on my phone

    I am unable to switch on my Iphone 4s, can any one help

    Hello,
    I have the same question. If the iPhone 4 is any indication then please use USB 2.0 port and the new accessories to charge it. I know that this sounds obvious but I found out later :(
    Hence when you connect your iPhone to the iTunes via USB 2.0 port does it detect it? (since it should try to turn it on to sync)
    Hope this can give you a little more insight.

  • My iPhone 4 has switched off for no reason , and now I am unable to switch this on again ??? if anybody has a answer about how I could reboot it , he's welcome, many thanks .

    my iPhone 4 has switched off for no reason, and now I am unable to switch this on again???if anybody could help about a reboot tip , he's welcome, many thanks...

    1. On your iPhone 4 press and hold both the button and the Home button for about ten seconds. After ten seconds you should see the Apple logo showing up.
    2. Now try to run you phone again and see if it works.
    If a hard reset the still can't get the device back to a working order.
    1. Plug in the device to the cumputer and start iTunes.
    2. Press and hold the Sleep/Wake + Home for 10 seconds.
    3. Once you see the Apple Logo appears, release the power and continue to hold down the home button for about 5-10 seconds. Look iniTunes and see if your device have shows up.
    4. iTunes will notify you that you are now in Recovery mode. Click on OK to continue with the restore process.
    5. Next press and hold on the SHIFT button and click on the Restore button. Select the latest IPSW file and the prompt appears.
    6. iTunes should now attempt to get your device back to the manufacturer setting.
    7. iTunes will later give you an opportunity to restore you content from the PC. Every time when you do a sync, iTunes makes a backup so you can choose the latest backup from the sync.

  • Sony Xperia Z1 No Alarm Display and Unable to switch off alarm

    Eversince I had the first Android Kit Kat update, my Xperia Z1 C6903 was not able to hear any notification sounds, my alarm sound worked but unable to switch it off or delete it and when my contacts call me, it send it straight to voicemail and I don't even hear the notifcation call sounds either. Did a reboot and went on safe mode, I still had the same problem. Found out online that there is a sound bug with my current firmware version: 14.3.A.0.681.
    When the new update 14.3.A.0.757 was available, I downloaded it. After this, my sound notifications worked fine, however, my alarm is still not working. Both on normal and safety mode, my alarm does the following:
    1) The alarm sound works
    2) Side key behaviour does not show up on my screen, so I am not able to dismiss my alarm
    3) I manually go to my "Alarm and Clock" app and press the "OFF" indicator. Alarm sound does not stop.
    4) I have to go to > alarm settings >Delete alarms >Choose the current alarm to delete > Alarm Sound then stops.
    This has been happening eversince the Android Kit Kat version was available for download (the previous and current one). I have reboot my phone, gone on safety mode, I have gone to >Settings >APPS> All> Clock > Clear Data, and went to the Sony PC Companion > Support Zone > Repair phone/tablet, as well as deleted all my apps.
    I do not know what else to do. I can only conclude that this is an existing problem with the new software update. I need my alarm working or else I am unable to get up for my morning meetings. PLEASE HELP!

    so i have been having the exact problem on my Z1. the alrm goes off at the right time....the notification works perfectly but you just cannot switch it off or snooze it. if i go to the drop down menu the active alarm is not listed there...the side buttons dont work or have no effect even when configured.
    you literally have to power the phone off for it to stop sounding. this is really annoying and i notice that teh last comment here was a month ago and Sony have still not addressed this problem. if you google this issue there a stacks of people with the same problem and more frustarted as we keep getting suggested fixes like clear clock cache which EVERYONE knows will not work as the problem is not with the data of the alarm....its a bug in the software that prevents the app from excuting teh way it was intended to.
    my alarms worked perfectly fine before teh update was applied. ever since teh update i ahev had this problem. i dont believe that a solution is to install another alarm app from google play store. i bought the phone which advertises the alarm as a feature and if sony cannot fix or address this probelm then you have falsely advertised...
    i am a sold out sony fan...i will never purchase any other brand of phone based on my past experience with sony products but this problem is making me think otherwise. give us a proper fix for this alarm issue and dont treat us like ignorant fools with your suggessted fixes like start in safe mode or reboot your phone....that will never ever fix the problem....its just a way of avoiding the fact that you dont know what to do to fix this problem...

  • My iphone 4 unable to switch on

    my iphone 4 automatically switch off and unable to switch on.

    Do a reset hold down the home/sleep button until you see the apple logo and then release, then wait for the phone to boot back up.

  • WinJS - Unable to switch on flashlight (using torchControl) on Lumia 930

    Hello,
    I am unable to switch on flashlight using torchControl on my lumia 930, when compiled the code gives no error and the app opens perfectly on the device. I researched a lot but was unable to find a solution to the problem... please help out.
    Thanks in advance.
    Here's the code that switches the flashlight on:
    (function () {
    "use strict";
    WinJS.UI.Pages.define("/pages/home/home.html", {
    // This function is called whenever a user navigates to this page. It
    // populates the page elements with the app's data.
    ready: function (element, options) {
    // TODO: Initialize the page here.
    var flashlight = new Flashlight();
    result.innerHTML = Flashlight.sendHTML();
    var mediaDev = new Windows.Media.Capture.MediaCapture();
    mediaDev.initializeAsync().then(function () {
    VideoDeviceController.torchControl.Enabled = true;
    ON.addEventListener("click", function () {
    Flashlight.lightON();
    result.innerHTML = Flashlight.sendHTML();
    OFF.addEventListener("click", function () {
    Flashlight.lightOFF();
    result.innerHTML = Flashlight.sendHTML();

    Hi DeadStarlin,
    Are both the computer and the phone connected to the Internet? On your computer, make sure that your web browser does not have
    Work offline enabled. Also, you cannot connect through a proxy server that redirects to a login page; for example, in a hotel or an airport.
    Is the phone turned on and the screen unlocked?
    Is your Microsoft account information correct and valid?
    If the above information still can not help, please try to restart your phone and computer to see if it works.
    Best Regards,
    Amy Peng
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • New out of box , unable to switch on is there a problem with the battery as i thopugh it should be  partly charged.

    new out of box , unable to switch on is there a problem with the battery as i thopugh it should be  partly charged.

    Plug it in for 15 minutes. If it doesn't come on hold the HOME button (the round one) and the SLEEP button (the one on the top) at the same time until an Apple logo appears (about 10 seconds). If nothing appears on the screen after 30 seconds you have a dead phone; take it back for exchange.

  • After upgrading from iOS 7.1.2 to iOS8 on my iphone5, i am unable to switch 2G/3G.

    After upgrading from iOS 7.1.2 to iOS8 on my iphone5, i am unable to switch 2G/3G, i think apple has removed that toggle. Poor 3G range is here in india-Pune. Requesting Apple Dev. Team to do the needful asap.

    ios 8 *****. i am unable to switch 2G to 3G while it eating my battery. *****

  • HT1414 i am unable to switch on the wifi on my iPhone 4s? I have tried all of the above ways.

    I am unable to switch on the wifi on my iPhone 4s.
    I have tried restart, restore, update etc.
    But its still not working.
    Please help

    Try the suggestions here to see if they resolve your problem:
    http://support.apple.com/kb/ts1559
    If these don't work you may have a hardware problem. Visit an Apple store for an evaluation or contact Apple Support.

  • Unable to Switch Audio Sync Settings

    Hey everyone,
    I'm trying to create an animation based off of a 5-minute mp3 audio recording. I need to be able to switch my audio sync settings to Stream so that I can preview audio anywhere in my animation. Currently if I press play just anywhere in the animation it doesn't play the audio. I have to play from the beginning to hear.
    After doing some searching on the Internet, I figured out I have to switch my audio sync setting to Stream so that I can play audio anywhere in the timeline. However, the only option I have available is Event. The other ones are greyed out, as the screenshots below testify. Any help would be appreciated. Thanks!
    Hardware and Software Statistics:
    Adobe Flash Professional CC (CS6) - Version 13.1.0.226
    Windows 7 Home Premium - Version 6.1 - Build 7601: Service Pack 1
    Intel Core i7, 4GB RAM, NVIDIA GeForce GT 525M

    The first the thing a person should always do when they encounter a problem is restart their computer. No worries, I did that.
    I tried converting the file to OGG and WAV to see if it would work better. Apparently Flash Professional handles WAV fine, allowing me to switch between Stream and Event audio sync settings. That's kind of strange, because WAV files are so huge and aren't practical when developing a game or something like that.
    Thankfully, I'm just using Flash Professional to export a video, so I don't care about file size, but it's a disturbing bug.
    If anyone knows why I was unable to switch to Stream audio sync settings with MP3 files, please speak up.

  • I dropped my Iphone 5 which resulted in it shattering and the screen was still on but it was black with only a white line through it so I couldnt access the phone however I switched over to my Droid and now I cannot send or receive messages?

    I dropped my Iphone 5 which resulted in it shattering and the screen was still on but it was black with only a white line through it so I couldnt access the phone however I switched over to my Droid and now I cannot send or receive messages and I cant turn off imessage because I cant see anything on the screen.  Help?

    Then the bottom of the support document states that if you do not have access to the device (which unfortunately because of the screen issue you do not) to contact Apple Care. That is what you need to do.

  • HT1414 my phone went on switch off mode since yesterday and not able to put on again till now.

    my phone went on switch off mode since yesterday and not able to put on again till now.

    I am having the same problem.

  • Unable to switch on my mw1

    dear sony team
    i am sandeep rathore from chhattishgarh bilaspur i purchasing a sony mw1 month ago but now iits not working , i am unable to switch on, even when i charging the led screen are not showing battery mono pls suggest what i am do.
    regards
    Sandeep Rathore

    You should take it to a Sony repair center
    http://www.sonymobile.com/global-en/support/contact-us/
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • Unable to switch Central System Administration into Change Mode

    Hi,
    I am bit rusty on the Solution Manager - Central System Administration.
    While experimenting with my Solman system I did the following.
    1. Logged into Solman and started transaction Solution_Manager
    2. Switched to the Solution that has been configured and then followed Operations Setup->Solution Monitoring -> System Administration -> Central System Administration for <My System> (here my system is the system I wish to monitor).
    3. After following the navigation to the selected item as described in step 2, I selected the menu items Session Components->Complete.
    4. After this action of selecting the Complete session from the menu, my Central System Administration for <My System> is continuously showing Display Mode.
    I am unable to switch back the system to Change Mode.
    Am I missing something ? What needs to be done ?
    Regards,
    Siddhesh

    Siddhesh Ghag wrote:>
    >
    > 3. After following the navigation to the selected item as described in step 2, I selected the menu items Session Components->Complete.
    >
    > Regards,
    > Siddhesh
    This was the wrong step. By setting the Session Component to "Complete", no further changes are allowed (and you receive a pop-up).
    The procedure to reopen the session component is not documented for customers. Please create a customer message on SV-SMG-MON-CSA, open the service connection and provide logon information.
    You might state my name in the message, I will then assist the message processor.
    Best regards,
    Ruediger Stoecker

Maybe you are looking for

  • Problem gettina PDF to play in a panel

    I have tried using the HTML widget to show a PDF file. I have tried the file locally and also linking to an online version. It all seems to work well and when I view this in Preview mode it looks fine and the PDF opens and gives me the controls, etc.

  • How to convert date format in VC 7.0 to DD.MM.YYYY

    Hi   I am on VC 7.0.   My requirment is to show Current date as a default value for a input field.   I am using date function now() as default value...and it is displaying the current date 08.07.2009 as  Jul 08,2009 But my requirment is to display it

  • TS3694 my ipad restore shows 2009 error ?

    how to restore my mini ipad after it shows 2009 error ?

  • ITunes 10.4 Update keeps crashing

    I allowed the update to 10.4 yesterday and iTunes now crashes everytime I open it. The crashes are intermittent and the first sign just before a crash the scroll bar freezes then Windows says that it needs to close iTunes. The event viewer displays t

  • Can I get a "new" old phone from Amazon and have it activated?

    Hello, I have an old Verizon LG VX8300 that I would like to replace with the same model which I can purchase at various online stores. My contract is long over and I pay month to month. Will Verizon activate this phone for me or do I have to get a ne