I recently switched from LinkSys to Airport Express 802.11n. I love it, but I can't get the Wii to talk to it so I can stream NetFlix. I've found MANY discussions on this, but it's still not clear to me. Anybody have a step by step so I can fix it?

I recently switched from LinkSys to Airport Express 802.11n. I love it...but now I my Wii can't see it so I can stream NetFlix. I have found MANY discussions on line about this...but it's still not clear to me. Anybody have a step by step way to fix this? Thanks! Jim Matherly

Well, the Airport Express is also compatible with 802.11a, 802.11b, and 802.11g. If your Wii is unable to connect to the wireless network, I recommended changing the wireless security of your network.
Open Airport Utility, select your Airport Express and click Edit. Navigate to the Wireless tab and change your security from WPA2 Personal to WPA/WPA2 Personal. Then click Update on the bottom right.

Similar Messages

Airport Express 802.11n problem

I have an Airport Express 802.11n.
I use it to send iTunes from my mac on my stereo system in the adjacent room, via my wireless network. I don't use it all that often. It has worked fine over the two or so years I've had it
A couple of weeks ago I had a new BT Home Hub 5 installed, this may be just a coincidence but I tried to use my Airport Express 802.11n yesterday with no luck. All I get is an amber flashing light. I've plugged the Airport Express 802 into the mains right next to my imac but that has not helped. My Airport Utility doesn't find or show my Airport Express.
What do I do? Can anyone help?
Hopefully
Rob

Here's an update:-
By re-setting my Airport Express 802 and updating the firmware, I can now get it to work when connected with an ethernet cable and changing my settings from DHCP to Bridge.
However, I still can't get it to work wirelessly.
Is this a known problem with the BT Home Hub 5 and BT Infinity?

Extending range of Linksys WRT310N router with Airport Express 802.11n

I am trying to extend the range of an existing wireless network set up with a WRT310N router with an Airport Express 802.11n - I've tried choosing both "Participate in a WDS network" and "Extend a wireless network" and both have run into problems.
Any advice would be greatly appreciated!
Thanks, Amy

amysinsh, Welcome to the discussion area!
Sorry but this is not possible.
It would be possible if the wireless network was created by another AirPort Express (AX), anAirPort Extreme base station (AEBS), or a Time Capsule.

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

Let me see if I can help you with the basic WDS configuration steps:
Note: To help facilitate the setup, temporarily connect the AXn directly to the AEBS LAN port using an Ethernet cable. Once the setup is complete, you can move the AXn to the desired location. For all configuration steps you will be using the AirPort Utility. Before starting, be sure to jot down the AppleIDs for both base stations.
802.11g AirPort Extreme Base Station (AEBS) Configuration
AirPort Utility > Select the AEBS > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network
Manual Setup > WDS tab
WDS Mode: WDS main
Allow wireless clients (checked)
WDS Remotes: <enter the AppleID for the AXn here>
Click on Update and allow the base station to restart.
802.11n AirPort Express Base Station (AXn) Configuration
AirPort Utility > Select the AXn > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network (Note: You may have to hold down the Option (Mac) or Control (PC) key to see this option in the list.)
Manual Setup > WDS tab
WDS Mode: WDS remote
Allow wireless clients (checked)
WDS Main: <enter the AppleID for the AEBS here>
Click on Update and allow the base station to restart.

After setting up my brand new Airport Express 802.11n and accidentally using it to connect my iMac to the network...my iMac no longer connects through Ethernet? Any ideas...I have tried everything without success!!

I have been using Apple technology for about 10 years starting with 1st generation iPods and our house now includes a 5 year old iMac, all versions of iPods and touches, Apple TVs (both generations) and most recently an iPad 2. I have always told family and friends that Apple technology just works. Unfortunately that stopped today. I bought a new Airport Express 802.11n to use for AirTunes around my new pool. I set it up from my iMac and accidentally used it to connect my iMac to the network for a short time. Now I can no longer connect the iMac to the network using a hard wired Ethernet cable. I have tried resetting everything possible, from hubs to routers to the Mac itself and it just will not connect to the network through Ethernet any longer. I am now a very frustrated Apple user especially when the support site says I can't use the fast path support because my product was manufactured 5 years ago...I just bought it at BestBuy yesterday. All other computers and itechnology in the house are connecting via wifi and Ethernet without any issue except from my new iMac boat anchor. Anybody who can help me??? Thanks

John, thanks for the email so quickly.
I too hope I haven't tried "everything" either but I am reasonably technical. I had done what you suggested to do before but I did both again.
Ethernet is yellow in the left side bar. In the right pane it's status says Connected but then below it says "Ethernet has a self-assigned IP address and will not be able to connect to the Internet."
I have tried the assist me menu and Network Status has Ethernet Green, Network settings Yellow, ISP Green, and Internet and Server Red and Failed for both. I have turned things off and on, checked cables, deleted all locations and tried restting them up but to no avail. I even disconnected everything and connected the mac directly into the cable modem itself and the thing still will not connect.
Thoughts???

I have an airport express (802.11n) which download do I need to get it work on Windows 8.1?

I have an airport express (802.11n) which download do I need to get it work on Windows 8.1?

That one doesn't work.
Verstuurd vanaf mijn iPhone
Op 19 nov. 2014 om 13:55 heeft "Apple Support Communities Updates" <[email protected]<mailto:[email protected]>> het volgende geschreven:
http://www.apple.com/support/assets/images/external/emails/logo.gif
You received a reply
Bob Timmons<https://discussions.apple.com/people/Bob+Timmons?ac_cid=op123456> has replied to your question. You can view the full discussion<https://discussions.apple.com/message/27128939?ac_cid=op123456#27128939> in Apple Support Communities.
I have an airport express (802.11n) which download do I need to get it work on Windows 8.1?<https://discussions.apple.com/message/27128939?ac_cid=op123456#27128939>
It has been some time since Apple updated AirPort Utility for Windows. The current version is 5.6.1.
It runs on Windows 7, but I have not checked on Windows 8.
AirPort Utility 5.6.1 for Windows<http://support.apple.com/kb/dl1547>
Correct Answer <https://discussions.apple.com/email/thread/6679920/correct/27128939> Helpful Answer <https://discussions.apple.com/email/thread/6679920/helpful/27128939>
Use the buttons above to tell Bob Timmons and the rest of the community if this reply solved your question or helped you get closer to finding a solution.
To reply to Bob Timmons, go to the discussion<https://discussions.apple.com/message/27128939?ac_cid=op123456#27128939> in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile<https://discussions.apple.com/user-preferences!input.jspa>.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved<http://www.apple.com/legal/> | Privacy Policy<http://www.apple.com/legal/privacy/> | Terms of Use<https://discussions.apple.com/docs/DOC-5952> | Apple Support<http://www.apple.com/support/>

Speed issue with WDS, Airport Extreme, and Airport Express 802.11n

I have a Airport network set up using WDS and two airport base stations: an Airport Extreme 802.11n, and an Airport Express 802.11n. The Extreme is configured to be WDS main and is connected to my cable modem and other computers, while the express is WDS relay and acts as a switch.
I don't actually have any wireless clients connecting to the express. I'm using it to connect a mac with no airport card to the network by plugging it into the ethernet port on the express. For the most part, it works, and the mac gets a network address and can access the network. However, the connection speed from the Express to the Extreme seems slower than it should be.
Since both are 802.11n, and the Mac is plugged into the Express's 10/100 ethernet port, I figure the theoretical top speed that the Mac should be able to communicate with another device plugged into the Extreme is at around the same speeds as 100 mbps ethernet, since the 100 mbps ethernet connection should be the bottleneck in this case. In reality, the speeds are much slower: when I transfer files between a machine connected to the extreme (via ethernet) and my mac, the speed tops out at about 2 megabytes a second, if that.
I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is! Also, the only wireless communication is between the Extreme and the Express, so one wireless device acting as a relay for another (and thus cutting the throughput in half) shouldn't be an issue.
Does anyone know why the speeds are so slow, and if there's anything I can do to improve them?

Hello Brian Kendall. Welcome to the Apple Discussions!
I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is!
That is because you established a WDS which only runs in 802.11g. Since you have two 802.11n base station, you would want to take advantage of the "Extend a network" feature available with these base stations.
Here's a typical setup:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

Airport Express (802.11n) as non-NAT router?

I am considering to replace an old WLAN router by an Airport Extreme. For this, the Airport Extreme unit would need to work as a non-NAT router (my network consists of multiple independent subnets). I've looked through the (very helpful) discussions, but could not find a definitive answer to this question. So, can you tell me point-blank whether an Airport Express (802.11n) base station can be used as a *non-NAT router* (connected to subnet A via the WAN port, creating a different subnet B on the LAN ports)?

broadwater, Welcome to the discussion area!
No this can't be done. The AirPort Extreme base station (AEBS) can be configured to create a single subnet for all clients (LAN port or wireless) but in that mode DHCP and NAT are enabled.

Airport Express 802.11n does not support 5 ghz range

I have a Airport Extreme and a Airport Express both are 802.11n. I have the Airport Extreme setup to 802.11n (5ghz only). The Airport Express 802.11n will not work in the 5ghz range no matter what I do.
If I change the Extreme to 802.11n (2.4 ghz only), and set the Express to 802.11n 2.4ghz, it works fine.
Both systems have been upgraded to the 5.3.1 firmware.
Apple claims the Express works in the 5ghz range. The unit I have does not..so what is the deal?
Steve

I finally got this to work at 5ghz.
BUT,
The Airport Utility that supports the Express is less then great. There is no manual option to set the Express at 5ghz as a client. I assume that Apple will fix this soon.
I also had the problem described in several places in this Discussion group, that the Express becomes un-available after changing the config. I finally just restored it to the default, unplugged it and let it sit overnight. Then I reprogrammed it, saved it, verified it works, then let it sit all day with out unplugging it. I then unplugged it and moved it to the location I wanted it at so I could stream music, and it worked fine at 802.11n/5ghz.

About My New Apple Airport Express 802.11n Wi-Fi Router

Yesterday on Saturday after i finshed work I Went out & Bought a New Apple Airport Express 802.11n Wi-Fi Router for My Apple iMac Computer & for My Apple iPhone 5 & Apple TV & I Set it up & everything & everything worked out well so i had a question about it, that Green Solid New Light on Apple Airport Express is it suppose to always stay on even if my Apple iMac Computer is Sleeping like other Wi-Fi Routers??? cause i'm wondering cause it looks Very Nice & White & Shiny & New & i don't really want it to Fail on me cause i do like it & it does not take up a lot of space witch is a good thing so just had to ask???
how many years will My Apple Airport Express Wi-Fi Router will last for since it's as Big an an Apple TV, just was wondering if this thing is really strong & stuff to like hold out for years time maybe???
will My Apple Airport Express Wi-Fi Router Software ever get Outdated like my other Wi-Fi Router??? & they stopped making that Belkin Wireless n Router that i had & they stopped Updating it's Software & then The Software became not usable at all so I Had to go out & buy an Apple Airport Express 802.11n Wi-Fi Router.

Hi Byron,
on the first question: take a look at your manual; I have a different router, and on it the light stays on all the time, but I don't know if the Airport works the same way. On mine, it simply means that it is on and ready in case you need it. You should worry when there is no light, LOL.
Second question: with electronics, can't tell at all how long they will be good for. They are made to be compatible with a certain range of devices and software - and will be updated for a while when those devices and softwares are updated. After a while, too many new routers are available with too many new features that are compatible with new devices and softwares, so it's not worth updating the old ones. It's a question of money - they don't want to give you free updates forever, they want you to buy a new piece of equipment.
Third: yes, it will at some point. Everything technology/electronics related is outdated - some very quickly: you buy a new one and the next week you see an ad for a "new, improved" one. Same principle: they want you to buy again.

BDP-N460 Blue Ray - Wanting to implement Airport Express (802.11n) as Wi-Fi

Hi All,
My intention is to use my Airport Express (802.11n) as a Wi-Fi bridge for the BDP-N460 (Streaming Video). I am clearly missing a step. I have read many posts and followed what seemed like specific directions, to no avail. If anyone can help by shedding some light on this process, I would greatly appreciate it.
All the Best,
NgM

I may have to wait to do the tests in the same room as the Linksys. What would the tests include? Setting up the Express directly to the (cable) modem?
This was a suggestion to test signal strength. If you want to try to configure it now, here is how you would do so:
It is critically important that you know the exact type of security that the Linksys router is using. Otherwise, you will not be able to match up the settings and the Express will not connect to the Linksys wireless. It would be great if the Linksys was using no security, but I doubt that this is the case.
Hold in the reset button on the AirPort Express until you see the amber light begin to blink more quickly. Hold another second or two when you see this, then release the reset button.
Temporarily, connect an ethernet cable from your computer to the AirPort Express.
Open AirPort Utility and click Manual Setup
Click the Base Station tab (under the row of icons) to assign a name to your Express, a device password (write this down) and adjust Time Zone settings
Click the Wireless tab (under the row of icons)
Wireless Mode = Join a wireless network
Wireless Network Name = If the Express "sees" a strong enough signal from the Linksys, you will see the name of the Linksys wireless network. Click to select. If you do not see the name of the Linksys wireless network displayed as a choice, I'm afraid that the wireless signal is too weak and this will not work.
Place a check mark next to Allow ethernet clients. This activates the ethernet port
Wireless Security = Exact setting as the Linksys. This is always the most difficult part of trying to get an Express to join a wireless network. It won't pick the right setting by itself. You have to tell is exactly what to do.
Wireless Password = Password for the Linksys network if security is being used
Confirm Password
Click the Update button at the lower right of the window. Don't panic when the AirPort Express "disappears" from AirPort Utility, this is normal. As soon as you see the message that the settings have been stored to the Express, close AirPort Utility and disconnect the ethernet cable. The Express will restart and if your settings are correct, you will have a green light in 20-25 seconds.
If you don't get a green light, something is wrong with the configuration settings, probably the security setting. You'll have to start all over again with the reset of the Express and try again.
Now, test the connection by first plugging your computer in to the Express, (turn off wireless on the computer) and see if you can get an internet connection. If you can, it should be simply a matter of plug and play with the Sony, following the instructions in the manual. Almost all Audio/Video devices will connect to the internet automatically when they have an ethernet connection. No special configuration is normally required.
The success of your connection will depend on the quality of the wireless signal that is available to the AirPort Express.
Good luck, post back on your results.

Unable to Connect Using New AirPort Express 802.11n

My mom purchased an AirPort Express 802.11n wireless router (AX) and I, as the designated "technology guru", was tasked with setting it up. Unfortunately, I am having problems out of the box.
When I connect it to the wall, it is found by AirPort Utility, but when I try to set it up, it is unable to connect to the wireless network. ("An error occurred joining the selected wireless network." "An error occurred, close the configuration window and try again.") This is annoying because I have an older AX and it was true to the "it just works" Apple mantra. It is also annoying because the error message has a comma splice.
Feeling pretty proud of my "technology guru" title, I come here to see what I could be doing wrong. I try connecting the computer directly to the router via ethernet cable. With this, I am able to setup my wireless network. I am still not able to connect to it. Additionally, once the AX has been configured, the AirPort Utility can't find it.
I tried updating firmware to 7.5.2. I've tried downgrading to 7.3.2. I've tried hard resets, soft resets. Every tip I could find I have tried. Please help. My self-confidence is wearing out.
Is it time for a call to Apple or a visit to the Apple Store?

Are you trying to configure the Express to "join" the wireless network?
If yes, the message you are receiving is likely an indication that you do not have the correct security settings selected for the Express. Unless the security settings between the wireless router and Express match up exactly, the Express will display the error that "an error occurred, etc".
The easiest way to confirm if you have this problem is temporarily set the main wireless router to "no security" and try to connect the Express that way. If you can connect, then you know that it is a security issue.
Please tell us the exact setting for security that the wireless router there is using and we'll try to give you some more ideas.
The Express will connect. It's just a matter of finding the right settings.
Message was edited by: Bob Timmons

Airport Express 802.11n on third party network

Hi,
I've got an 802.11g wireless network with one older Airport Express 802.11g Base Station and a newly purchased Airport Express 802.11n Base Station. For some reason the new Base Station won't work properly on the 802.11g network. I can configure it from factory settings and it will connect to the network but as soon as I try to get it up and running with the older Base Station it disconnects and can't reconnect to the network. Is there anyway to configure the newer 802.11n (default) Base Station to boot with 802.11g as its default protocol?

Did you set up the new AX in "Join a wireless network" mode? After you restart the AX, is there a steady green light on it? Can you see the AX on Airport Utility.
If you are still having problem, try disable the security temporarily see if that is causing the problem.

Can connect a mac LAN Airport Express 802.11n to an existing PC's LAN...

Hi. In my company we have a PC wireless LAN with internet routed with DHCP and mac/wep security. Can the Airport Express 802.11n connect it to that network, and share the internet and win network to macs, conforming another intranet...?
Thanks in advance.
Sorry but I'm new in Airport topics.
Enzo.
iMac Intel Core Duo 2Ghz/2GbRam Mac OS X (10.4.8)

The new Airport Extreme can do this.
There is a bridging mode which will simply extend your network to wireless.
You have the option of a backwards compatible 2.4GHz mode. Which will support older WiFi hardware on Macs and PCs.
And there is a faster 5GHz mode which will work with newer Macs (and presumably 802.11n equipped PCs)

Airport Express 802.11n Wifi firmware

Hello,
i have an Airport Express 802.11n Wifi Model-Number: A1264
Somehow Airport Utility cannot update the firmware to 7.x. It is stuck at 6.3.
I tried loading the firmware while holding the option key. But Airport Utility tells me it cannot install the 7.4.2 Firmware on this device.
Also there is no option for "n network in the wireless settings in the utility.
What can i do? Whats wrong with may Airport Express?

I don't have my long list of Apple model numbers handy, but I can confirm that if you bought an AirPort Express(n), you would certainly see a Radio Mode option to include 802.11n when you look at the settings in AirPort Utility.
I believe that the firmware for the 802.11n models started with version 7.3.1. I would guess that the "7" designates the addition of "n" capabilities.
I suspect a mistake was made and the device will need to be exchanged.

I recently switched from LinkSys to Airport Express 802.11n. I love it, but I can't get the Wii to talk to it so I can stream NetFlix. I've found MANY discussions on this, but it's still not clear to me. Anybody have a step by step so I can fix it?

Similar Messages

Maybe you are looking for