I replaced battery and now will only turn on when plugged into a charger..

I replaced my batter on my iphone 3gs and then it will only turn on when i connect it to a power source.
After it has turned on you can take it off charge and it will stay on...
Help please!! thanks

Either you got a bad battery, didn't install it correctly, did some other damage while installing, or haven't let it charge enough yet. There's really nothing we can do to help you with any of those scenarios.
Regards.

Similar Messages

  • IPod very low on battery and now won't turn on when plugged into PC

    I haven't used my iPod for a few weeks, so now the battery is obviously completely empty. The problem is that it won't turn on when I plug it into my PC to charge, even after half an hour or longer. Is there something I can do, or do I need to get a completely new battery put in?
    iPod nano    

    If you are unable to give specifics about the problem or what you need to do, it's going to be rather hard to give you recommendations or alternate suggestions.
    As I said, if I recall correctly, the iPod will stay on if it's being charged. But, in case I'm misremembering, are you holding down the button until you see the red arrow that says "Slide to power off"? Have you tried restoring it?

  • My iPhone will not charge and will only turn on when plugged into adapter.

    I have tried to reset and nothing. It turns off if I unplug it and will only turn on when plugged in. The charge has not moved above 19% even though I let it charge for 3 hours while I was out. What do I do?

    http://support.apple.com/kb/TS2802

  • My ipod nano 6th gen will only turn on when plugged into a power source.

    My ipod nano 6th gen ONLY turns on when it is plugged into a power source. As soon as I unplug it, it turns off. I also tried to reset it and it did not help. Any suggestions? 

    Howdy mela1223,
    If I understand correctly your iPod will not stay on unless you have the charger plugged in even after resetting it. Normally this would indicate a hardware issue that would need a repair but to cover all the bases before that, the last troubleshooting that can be done for it would be to restore it with iTunes on a computer. 
    Restoring iPod to factory settings - Apple Support
    How to restore iPod
    Verify that you have an active Internet connection, because you may need to download new versions of the iTunes and iPod Software.
    Download and install the latest version of iTunes if necessary.
    Open iTunes. Connect your iPod to your computer using the USB or FireWire cable that came with your iPod.
    After a few moments, your iPod will appear in the Source panel in iTunes.
    Select your iPod in the Source panel. You will see information about your iPod appear in the Summary tab of the main iTunes window.
    Click Restore.
    If you are using a Mac, you will be asked to enter an administrator’s name and password.
    A progress bar will appear on the computer screen, indicating that stage one of the restore process has begun. When this stage is done, iTunes will present one of two messages with instructions specific to the iPod model you are restoring.
    Disconnect iPod and connect it to iPod Power Adapter (typically applies to older iPod models).
    Leave iPod connected to computer to complete restore (typically applies newer iPod models).
    During stage two of the restore process, the iPod displays an Apple logo as well as a progress bar at the bottom of the display. It is critical that the iPod remain connected to the computer or iPod power adapter during this stage. 
    Note: The progress bar may be difficult to see, because the backlight on the iPod display may be off.
    After stage two of the restore process is complete, the iTunes Setup Assistant window will appear. It will ask you to name your iPod and choose your syncing preferences, as it did when you connected your iPod for the first time.
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • My iphone4 got wet and was working right after but I shut off and have in bowl of rice by dehumidifier. But now it only turns on when plugged in. If I take to an Apple store will they be able to tell me if it's salvageable ?

    My iphone4 got wet and was working right after but I shut off and have in bowl of rice by dehumidifier. But now it only turns on when plugged in. If I take to an Apple store will they be able to tell me if it's salvageable ?

    Apple will not attempt to salvage it. They will offer you a replacement iPhone 4 for $149.

  • Dropped iPhone 4s and now won't turn on unless plugged into wall

    Hi there,
    So I dropped my iphone 4s onto a hard floor 2 days ago, it was at 95% battery at that point. It now will only turn on when I plug it into the wall, and as soon as I unplug it, the phone turns off immediately.
    When it is plugged into the wall it shows 100% battery and the signal (both wireless and carrier) are very touchy and it says 'searching...' a lot of the time.
    I have had the phone for 19 months now and am out of warranty. It is also worth noting that 1 month ago I replaced the battery myself because I was having battery issues and it has been working perfectly since then up until this incident.
    If anyone has any idea of how to fix this or any idea of what the problem may be it would be much appreciated. I have tried holding the home screen and top button simultaneously and also tried plugging into my laptop to restore but the laptop will not start the phone up, it just goes into a cycle of going to apple logo screen and then shutting off.
    Thanks very much.

    The drop either jarred loose the battery connection or cracked the main circuit board. As you have repaired it yourself Apple won't touch it, so you might as well take it apart and see what has happened.

  • My iphone is fully charged but it will not turn on unless plugged into a charger

    my iphone is fully charged but it will not turn on unless plugged into the charger in the wall, it wont even turn on when connected to the computer!!!!!!!

    Hi there. Any luck with your phone? I'm having the same problem

  • IPhone only turns on when plugged into wall

    Hello, I have an iPhone 4 CDMA and it only works when in is plugged into the wall.  It does not work properly anyother time.  When I plug it into the computer it goes through the Boot Loop.  When I put it into DFU mode and recovery mode and try to restore it in iTunes it doesn't restore and just gives me a bunch of different error codes.  The most common error codes are 2001, 2006, or 1604.  It use to give me Error 21 but I fixed that by editing the hosts files.  I have tried six different computers and seven different iPhone cables on the computers and I still get the same error codes every time.  It does not work if it is not plugged in.  I have replaced the dock connector/charging port and the battery.  I bought it used and think it may have been jailbroken at on time.  It has not been jailbroken in the time I have had it.  I have also tried Tinyumbrella and that did not work.  What could be wrong with it? 

    Hello! When it turns off, do you notice if it drains quickly or does it just shut off even with full battery? Because this can also be caused by battery problems. Your iPhone may not be turning on even when plugged into a computer because a wall outlet charger gives off more power than a computer does.
    I suggest you bring your phone to an Apple store right away. They could at least help you determine the problem, and by then, you can decide what to do with your iPhone - you can have it repaired (if they say it's still fixable), you can have it replaced with a refurbished iPhone, or you can buy a new phone completely.

  • How do I restore my iPod Touch that only turns on when plugged into the wall?

    I found my old iPod Touch 4th generation in my backpack, and my backpack went through the wash, (It shouldn't of been too bad since it was in the side pocket) but it goes dead instantly as soon as I take it out of the wall charger, and it does not turn on when I plug it into my computer. It also has a pass, (That I forget) so I need to restore it. Is it possible to restore it without connecting it to a computer?

    No. You have to connect the iPod to a computer with iTunes to restore the iPod.
    Did you throughly dry the iPod before you started try to use it?
    If not try by
    How to fix a wet iPod or iPhone | eHow.comfix-wet-ipod-iphone.html

  • My 3GS turned off with a low battery, and now will not turn on

    I have charged it fully, tried hard restarting, tried plugging it into my computer, tried pressing the home button while plugging it into the computer etc.
    My question is really about how to contact apple in regards to getting it fixed. This is a replacement phone and it did not come with a warranty (or more accurately, I was too late to renew the old warranty when I got it). However if it had come with a warranty, it would have been within the warranty period (8 months). To me this gives an implied warranty on workmanship and parts. I live in regional Australia which makes going into my local apple store a little difficult, and I don't want to have to pay for tech support for them to tell me that I should try restarting it.
    End rant.

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                     
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Ipod classic 160gb will only turn on when plugged in

    i recently got a ipod classic from a friend of mine who has no use for it and i knew there was something wrong with it but its confusing. the ipod will turn on if plugged in but will go to chatging please wait screen and never charge. if you put ipod in disk mode you can restore it but it will just go back to "charging please wait" after its done. i have no way of getting a new battery nor do i think i need to. i have tried all the the options there are , oh and i also have yet to see an apple logo and it turns off if i unplug it.

    Sounds like a dead battery.  You can have Apple replace it for a flat fee plus shipping and handling, or you can send it into a third party service center who can do the same job for a little less.
    Google for third party repair centers.
    B-rock

  • IPod classic won't turn off when plugged into a home theater dock; what's up? will it hurt to leave it on all the time?

    I bought a new iPod Classic and it won't turn off when plugged into a home theater dock. Is this normal and will it hurt the iPod if i leave it on all the time?

    Hi there,
    How old is your Classic? Often, after a couple of years, rechargable batteries begin to fail, especially after such a long period of inactivity. This happens with any gadget with this type of battery.
    Try leaving it plugged in for 24 hours, and try again, to rule out that it isn't just really low on charge. If this doesn't help, it may be a good time to buy a replacement. New iPod Nanos and Touches will be released this October.
    Below, I've linked to an Apple website which explains rechargable batteries, and why yours may not be working.
    Apple - Batteries
    I hope this helps, and I hope upgrading your device will not feel like an unnecessary expense. Let me know if you have any more questions,
    Nathan

  • My phone 5 died and now it wont turn back on or seem to charge at all. I've tried several different charger cords and outlets. And all the phone will do is show the empty battery symbol. please help! Any suggestions are apprecaited!?! thanks

    My phone 5 died and now it wont turn back on or seem to charge at all. I've tried several different charger cords and outlets. And all the phone will do is show the empty battery symbol. please help! Any suggestions are apprecaited!?! thanks

    Hello Cooper,
    Thank you for the details of the issue you are experiencing with your iPhone 5.  I would be concerned too if my iPhone was not powering on.  I found an article with steps you can take when you encounter an issue like this.  I recommend following the steps below:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    My issue is still not resolved. What do I do next?
    Contact Apple Support.
    You can find the full article here:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • My Iphone 4 just shut off and now will not turn back on.

    My Iphone 4 just shut off and now will not turn back on. I was listening to music, it started to make a static sound then shut off and will not turn back on. What do I do?

    Battery dead?
    Plug it into the charger that came with the iPhone and plug that into a known good wall outlet. Leave it plugged in for 20 minutes. Then while still plugged in reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.

  • My phone was updating the new software and now will not turn back on, what do i do?

    my phone was updating the new software and now will not turn back on, what do i do?

        Never fear, help is here jpeterson4! Have you attempted to plug your device into your home computer? Have you verified that the device is charged? Does anything appear on the device when you plug the device into a charger? Please keep us posted, thanks!
    MatthewS_VZW
    Follow us on Twitter @VZWSUPPORT

Maybe you are looking for

  • Application specific button on FPM toolbar to call action triggered in view

    Hello, In the content area of my FPM is an ALV with some buttons, e.g. clicking one of the button opens up certain ALV column for editing (for simplicity, I omit the details besides simply enable the columns). With FPM, I want the button to be placed

  • Flash animation doesn't work when I publish Captivate file

    Hi, I have an e-learning developed by a third party using Captivate 6, they've inserted animations (swf files) created using Flash CS6. When I try publishing the Captivate file on my computer all the animations work well except for a particular one (

  • VO CONTAINS ALL THE DB ROWS AUTOMATICALLY WITHOUT ANY QUERY EXECUTION

    HI ALL, I am getting a strange issue. I have two VO say UserVO and PasswordVO. When i run the application i am not using any BC component in HomePg. I click on login and through another read only VO i am authenticating. After authentication i am doin

  • Best way to manage external photo collection with iPhoto?

    I have a large collection of photos that now resides on an external NAS drive. I used Canon ZoomBrowser EX software on Windows to download the images from my cameras, but I want to start using iPhoto on my MacBook instead. There's no metadata associa

  • Follow feature shows server name URL instead of AAM URL

    hi - My sharepoint site http://servername has an AAM set to ooint to http://sitename The site works fine.   However when I follow any sites it places them in my Followed Sites as http://servername instead of http://sitename. Any ideas?  thanks