I restored my ipod, but when the process finishes, apears a message saying ihave to restore again, then i restore, and the message appears again, and again.

I restored my ipod, but when the process finishes, apears a message saying ihave to restore again, then i restore, and the message appears again, and again.

Maybe:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
Next try placing in DFU mode and then restoring.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
Then try restoring on another computer.
Last, make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Similar Messages

  • I restored and updated my iPod, but when I turned it on, it still says connect to iTunes

    My brother just got an ipod for Christmas, and we told him not to put a passcode on it because he would forget... but he did it anyways and he did forget! He ended up disabling it trying to unlock it. It said ''Connect to iTunes." When I connected to iTunes, it said it was disabled and needed the passcode to do whatever,  but I held the top button and the home button down for ten seconds to Restart it because we don't know the passcode! It said to Restore and Update, so I did that. Now it's in Recovery mode... and I can't get past that part! I thought I had done it right, but when it turns back on, it still says connect to iTunes! Help??

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen        
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

  • Officejet A909a prints from mac but when from windows "out of paper" message appears.

    I have an older 8500 which has been very loyal to me and I have looking after it well, which is now pushing 4000 pages.  However i went to print a file from my Windows 7 PC yesterday which is connected via usb, and it wouldnt print saying it was out of paper (which it wasn't) about half full . So i tried again no luck. UN-installed then reinstalled the printer still noting. went to my work laptop (windows 7) which is connected wirelessly through the network, same again "no paper" message appears. i thought this is strange turned it off back on still nothing even after disconnecting it from the mains for a few minutes, nothing the same message still appears. 
    However, my son has a mac book pro and he just printed his coursework off the printer effortlessly through my network. so i know the printer is fine especially as i have now printed self test pages off through the printer itself.
    I have no idea what to do now, as i have tried uninstalling then installing, printing via usb and network. and when i say "out of paper" i mean the printer receives the print command from my computer as it tries to feed paper a few times but cant pick it up also i have tried with various paper levels in the printer (full, half, about 20 pages, 1 single page)
    Please help.

    Hello @Dangerous97,
    I understand that when printing from your 2 Windows 7 computers you receive an 'out of paper' message after your HP Officejet Pro 8500 All-in-One Printer struggles and fails to pick up paper. However, you are able to print from a Mac computer. This is very unusual behaviour!  I would like to assist you today with resolving this issue. Also, thank you for including that you are able to print self-test pages from the printer with no issues as well.
    Generally, 'out of paper' messages are caused by a hardware issue with the printer itself. Because you are able to print standalone to your printer and from a Mac, there may be an issue with the documents that you're trying to print from your Windows 7 computer or a programming issue with your printer.
    With that being said, to start I would like you to click here to download and install the latest programming Firmware Update on your printer. Once the website opens select the Download button on the top left. Once the download is complete, please follow any onscreen instructions to send the update to your printer.
    Once the Firmware has been successfully updated, please test printing again.
    Please respond to this post with the result of the Firmware Update. Good luck!
    X-23
    I work on behalf of HP
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping!

  • Canon EOS 100D is listed as compatible in Digital Camera RAW Compatibility Update 6.01 but when I connect my camera a message appears telling it's not compatible with the operating system?

    Canon EOS 100D is listed as compatible in Digital Camera RAW Compatibility Update 6.01 and when I have checked for software updates there are none available.  I've downloaded the Canon software, connected to my mac via the cable and followed the instructions in the manual.  Sadly I just get a message saying it's not compatible with the operating system.  I've tried inserting the memory card into the mac to and it doesn't seem to see it.  Can anyone help please?

    Camera RAW ≠ Camera driver, the RAW update is for the .CR2 canon raw image file (in your case) compatibility.
    What happens when you try to import photos using Image Capture or iPhoto?
    Can you take a screenshot of the error message?
    I always prefer and recommend using memory card import over using the camera.

  • I log out properly but when i log back in a message appears basically saying it cant open my page due another one being not closed properly before. WHY?

    I log out correctly every time making sure all windows are closed but every time i log back in a window appears saying "well this is embarrassing, we are having trouble opening your page (or something close to that, i cant remember the exact words) then at the bottom it says"this is usually due to a window being open (or close to that) then it asks me if i want to close or restore the session and it has a list of the last 2 pages i opened.
    But i ALWAYS close them before logging out. Why does it keep doing this? Do we have a clever hacker or something?

    hello lexi, this is currently a problem in firefox when you first close all open firefox windows and then close the application afterwards - the bug should be addressed in a later version of firefox.
    as a workaround in the meanwhile you could close firefox (through firefox > quit) while the browser window is still running or try this: enter about:config into the firefox location bar (confirm the info message in case it shows up) & search for the preference named '''browser.sessionstore.resume_from_crash'''. double-click it and change its value to '''false'''.

  • The settings app is showing that there is an update but when i go to software update it says its full up to date. HELP?!

    my settings app has got the red 1 to say that there is a notification/update, but when i go to update it it says that i am on 6.1.4 and i am full up to date, what else could this notification mean?

    If the MBP is new why do you think it needs updating to 10.8.4? What version is currently installed?

  • My itunes store is saying that it could not contact the server, it says i need to restore my ipod but when i go to restore it, it says the server could not be contacted or something. what does this mean?

    okay so last night i went to charge my ipod in the computer and it started working then i took it out of the computer and put it on a wall charger and it had a spasm attack and shut itself down, after that it said i had to connect it to itunes so when i did it kept telling me that i need to restore my ipod, but when i press restore the itunes said "the contact server is not avalible" or something similar to that, what does that actually mean and is there anyway i can fix my ipod. i have dropped my ipod a few times, on tiles, wood, in a gutter of water when it fell out my pocket but im also wondering is it something to do with my ipod or is it itunes?

    Try:
    iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
    The abuse may prevent a restore or prevent proper operation of the iPod if you can restore the iPod.

  • My 5th ten iPod is basically doing nothing but trying over and over again to start up. I've tried to restore it, but when the logo apple appears, it simply shut down.

    my 5th ten iPod is basically doing nothing but trying over and over again to start up. I've tried to restore it, but when the logo apple appears, it simply shut down. Then I've connected it to my macbook pro, and I've seen the script "Please Wait - Very Low Battery", but, after some time, the iPod tries to start up again, and nothing happens. It's a kind of noise, I'm thinking about the hard disk, (it's a 80Gb version), and I'm listening to it; every 30 seconds seems to try to open and then shut down again. I can't see the iPod in iTunes too. Don't know what to do. Can someone help me? Thanks a lot, it's my first forum

    It sounds like the battery could be going bad as well as the iPod's Hard drive.  You'll want to have the iPod serviced either by Apple or a third party repair company. Here is Apple's pricing:
    http://www.apple.com/support/ipod/service/prices/
    Google for "iPod repair" and you should get a ton of results to work with.
    B-rock

  • My iPod classic, which is 6 years old is corrupted. A message that says ''Connect to iTunes to restore'' keeps on blinking on the screen, But when I connected it to iTunes it says an error has occured and my iPod has hung after i've disconnected it.

    My iPod classic, which is 6 years old is corrupted. A message that says ''Connect to iTunes to restore'' keeps on blinking on the screen, But when I connected it to iTunes it says an error has occured and my iPod has hung after i've disconnected it.

    Hi,
    Time to take your iPod in for service.
    You can make a Genius Bar reservation in advance if you are in the U.S.
    http://www.apple.com/retail/geniusbar/
    Carolyn 

  • When i plug in my ipod classic it pops up ipod corrupted and i should restore the ipod but when i try it pops up unknown error 1415

    when i plug in my ipod classic it pops up ipod corrupted and i should restore the ipod but when i try it pops up unknown error 1415?

    My suggestions, when Restoring the iPod.
    Disconnect your PC from Internet. (just to make sure no nasties creep into your system while you syncing.
    Stop the Antivirus program
    Connect your iPod to the PC, using a high speed USB 2.0 port at the back of your PC.
    Disconnect all other USB devices, except the mouse and keyboard.
    Stop all other programs except iTunes.
    Good Luck!

  • I am going to sell my second generation ipod touch, so i resetted it to factory defaults. It said it would take up to an hour, and i patiently waited. But when the black and white loading bar completed, the ipod went to the black screen with an apple logo

    I am going to sell my second generation ipod touch, so i resetted it to factory defaults. It said it would take up to an hour, and i patiently waited. But when the black and white loading bar completed, the ipod went to the black screen with an apple logo on it. Sounds about right, right? But now, there is a processing circle on top of the logo, but the circle spins once, and stops at about halfway to the bottom. It just stays there, and about every half to one hour it becomes a white screen and starts all over again. (not the loading bar part, just the circle). I've tried holding the power and the home button, and it works, but it just goes back to the circle screen with the apple logo. HELP PLEASE?

    Try:
    - iOS: Not responding or does not turn on
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • My ipod has had a previous owner How do I change my ipods email address so that when I try to down load anything it asks for the previous owners password but when I go to my account it says its my email my account but not when I try to download????

    My ipod has had a previous owner How do I change my ipods email address so that when I try to down load anything it asks for the previous owners password but when I go to my account it says its my email my account but not when I try to download can anyone please help me ????Plus it still has some of the previous owners pictures and videos on it that I want to delete and can't????? Also is there a way to kill the apps that u have used throughout the day the battery doesn't last long at all ??????

    - How did you dlete stuff from the iPod? If you have a 1G or 2G iPod and deleted the stuff by going to Settings>Genera.>Reset>Erase aall contents and settings without being connected to a power source, the battery dies before he erase was comleted since it can take hour.
    - In any event try the following:
    - Connect to a chaging sour for three hours.
    - Reset the iPod and then connect to the computer and try to restore va iTunes.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Next try placing the iPod in recovery moe and then try to restore. For recovery mode:
    iPhone and iPod touch: Unable to update or restore
    - Last try DFU made and restore.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

  • HT1386 I am re-building my iTunes library, but still have all the content on my iPod Classic.  I have just downloaded some songs from the store and want to add them to the iPod, BUT when i attempt this the message asks if I want to delete all content on t

    I am rebuilding my iTunes library, but still have all the old content on my iPod Classic.  I have just download some songs from the iStore and want to add them to the iPod, BUT when I try to sync it asks if I want to delete all content from the iPod and add only the material that I have just downloaded from the Store.  I do not want to lose my old content, because it is very extensive.

    You are trying to sync to other than the one iTunes library you can sync to. You can copy music from multiple library/computer if you use the manual method of syncing. That method is described here
    iTunes: Syncing media content to iOS devices and iPod
    If you want to make this computer/iTunes library your syncing computer/library you have to restore the iPod on this computer/library. Restoring erases the iPod.
    You can redownload most iTunes purchases by:
    iTunes: Syncing media content to iOS devices and iPod
    To copy other music to the computer see:
    Recovering your iTunes library from your iPod or iOS device: Apple Support Communities
    BTW this is the iPod touch forum

  • I have an ipod touch 8gb that is disabled. on the screen it reads ipod disabled connect to itunes. But when i connect it to itunes, it says that it cant work with the ipod because it is locked with a passcode. what now?

    I have an ipod touch 8gb that is disabled. on the screen it reads ipod disabled connect to itunes. But when i connect it to itunes, it says that it cant work with the ipod because it is locked with a passcode. what now?

    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen
    If recovery mode does not work try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    The previous responses did not say how to place in recovery mode or DFU mode

  • HT1414 hi everyone , having trouble with restoring my iphone, i did follow the step untul extracting the update software but when the iphone start to restoring my iPhone always turn off and it say Error 21 on my PC monitor ...please help me icannot get my

    hi everyone , having trouble with restoring my iphone, i did follow the step untul extracting the update software but when the iphone start to restoring my iPhone always turn off and it say Error 21 on my PC monitor ...please help me i cannot get my iPhone turn on

    Error 20, 21, 23, 26, 28, 29, 34, 36, 37, 40
    These errors typically occur when security software interferes with the restore and update process. FollowTroubleshooting security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.

Maybe you are looking for

  • My web page centers in the design view, but not when viewed on line.

    I am new to web design and of course, to this forum.  I had some background in VBA and Fortran, so when the original designer left, I was the only one in the organization willing to tackle the website and try to teach myself how to make it work and k

  • Video not displaying properly and not exporting.

    I'm using Premiere Pro CS4 and After Effects CS4.  I brought an AFX composition in via Dynamic Link, made copies of the clip, chopped it up and spliced it back together on one video layer.  Within the Premiere Pro interface, the video shows up normal

  • Number of connections in a JDBC pool

    Hi, I am running Sun One Webserver 6.1SP4 on Solaris 8 on sparc machines. My web app interacts with Oracle 9.2 using the web server's jdbc pooling mechanism. Everything works fine, but what worries me is the number of connections always goes up even

  • How to use -XexitOnOutOfMemory?

    Hi, I am building new WebLogic Servers for ADF running on "jrockit-jdk1.6.0_45-R28.2.7-4.1.0". We have an issue that we're working on where we get OutOfMemory errors. Regardless, Based on this document: -XX Command-line Options ,  there is a paramete

  • ERROR:when running runcluvfy.bat command.

    Hi When i tried to run the runcluvify.bat command its showing that it is failed.i have given the command C:\clusterware\cluvfy\runcluvfy.bat stage -pre crsinst -nRAC1,RAC2;.Is there any prob: with the name of the iscsi initator.What should i do to so