I restored my phone and now receiver is not working
My phone crashed several times in the last week while on the road. It would Go into auto shutdown. I restarted it and would get the same error. Finally I did a reset. I could not plug into iTunes since I am on the road.
NOw my ringer does not work. The speaker works, blue tooth works, and my earbuds work, but not the ringer. How do I resolve this issue?
Do you have Do Not Disturb enabled? Settings>Do Not Disturb
Do you have the mute switch engaged? It's the little slider over the volume buttons on the side. If you can see orange, it's engaged. Slide it the other way.
Similar Messages
-
I updated my IOS on my iPhone 4S and it locked up. I had to restore my phone and now iTunes will not go past the setup your phone screen even though the phone as been restored. How do I get iTunes to go past this screen so I can sync my phone again?
Depending on what iPhone you have when you get to the connect to wifi you should be able to activate your device over cellular data. Try doing a hard reset by holding the home circle button an power button until an apple pops up and the go through the setup again and when you get to the wifi part a option should be setup with cellular data iPhone 4 and above should give this option sometimes doesn't like showing up that's why u have to do a hard reset first
-
I have an iphone 4s and i keep getting an error message when ever i try to activate i have already restored the phone and it still will not work. any help would be greatly appreciated
Activation issues are almost always the result of a device that has been hacked or jailbroken. If that is the case, no support can be provided here.
-
Restored my phone and now i can not reactivate the phone
Was having problem with my 4s so I backed it up and did a restore back to factory settings. After the restore my phone and iTunes are both giving me server errors and I can't reactivate my phone. Before I call apple support I was just wanting to know if there was anything I could try differently.
You are listing the wrong iOS in your profile. What is the actual iOS on your device?
Settings > General > About: What does it say next to Version? -
Help! I synced my phone and now it's not working?!
I synced my iPhone today to get the new version 1.1.3 and it was going well until I noticed that my phone service wasn't working. I powered the phone off and powered back on and now all I get is a screen that says "slide for emergency" and all I can do is make an emergency call??????
Ok -- problem solved but I don't know why.
After iTunes gave me that error message, I noticed it showed my iPhone under devices so I clicked on sync. That gave me a new message on iTunes that said it couldn't read my SIM card and to go to the AT&T store to get a new one. Out of frustration I removed the phone from the dock and then put it back in the dock...this time I got a message on my phone that it had been updated and when I clicked the slider it wanted my passcode. And my phone service appears to be fine.
But.. to avoid this scare next time...I assume I should leave the phone plugged into the computer until I get the "phone is updated" message ON the phone. Correct? -
I can only use my phone by using the speakerphone. I have rebooted and restored. What is the solution
No case. The issue seemingly went away overnight. I don't know what caused it to occur or what happened to make it go away.
-
HT4623 i restored my iphone and now it does not work
i restored my 3gs now it don't work
If you provide some more details, including the wording of any
error messages, someone might be able to offer a solution. -
I tried to update my phone last night. When I woke up, it said it needed to be connected to iTunes. I restored my phone and now it won't turn on and keeps saying it needs to be connected to iTunes.
probably need pc or mac update for ios 6 on your home device
-
I restored my phone and now it is asking me to activate it and i am trying but it is saying i cant activate my phone with my own id that i have to use the id that i used to set up my iphone the very first day i got it but that is the id. help please
You can try calling Apple support at 0800-761-0880 and explaining the situation to them. Perhaps there will be something they can do to help. Try asking to speak with a Customer Relations representative, though I don't know if they have them in Brazil.
Regards. -
HT1491 i had to restore my phone and now i cant find my ringtones?
i had to restore my phone and now i cant find my ringtones? also i cant get my pics back right?
All troubleshooting steps to try and resolve the issue for activating iMessage can be found in the link below:
iOS: Troubleshooting FaceTime and iMessage activation
Note: If "Waiting for Activation is displayed, leave iMessage enabled for 24 hours. Toggling iMessage off and on will cause the registration process to start over. -
I have an iphone 5. It has a "no sim" in upper left corner. I removed it, placed it back, restored the phone and now I can't get past the "activation" part. It's telling me to insert a SIM w/out a PIN lock. HELP!!!!!
Hi Michellebone,
I'm sorry to hear you are having this issue with your iPad. Given your description of the issue and the symptoms you are seeing, it sounds like you may need to have your iPad evaluated or serviced. You may find the following page helpful:
Apple - Support - Service Answer Center
Sincerely,
- Brenden -
I am trying to restore a phone that the screen does not work on, therefore I can't input my password. How can I bypass this and upload it to itunes?
You could follow the instructions in the support document that you linked from. There is a section regarding the passcode and the inability to use it or enter it. However, you may encounter more issues since you cannot use the screen.
-
Got a replacement Ipod Touch 3rd Generation and backed up to store version on computer and now it will not work. Goes into restore mode but cant restore. Any suggestions
What happens when you try to restore? Error message?
-
I turned off the power to my apple tv whilst updating and now it will not work, i have tried to restore using usb but it says unable to find. any help please?
Welcome to the Apple Community.
Are you following these instructions.
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Source list, and then click Restore. -
upgraded to iphone 5c at the end of Dec. I accidentally washed my phone and now it doesn't work. Is there a way to get a new or refurbished iphone 5c without signing a new contract?
Thank you. I've been looking online for refurbished iphones but that is cheaper than buying a refurbished phone.
Maybe you are looking for
-
Supporting Special Language Characters
If you have had difficulty composing emails in languages other than English, please know that Verizon is working to quickly address the issue in both Message Center and the Rich Version of Classic Webmail. Additionally, you may want to confirm that y
-
Submit and return and after that what?
Hi all, Iam successfully submitting a standard program.My problem is what I want is the final internal table values,how can i get that? Here is my code : tables : mseg,ioheader,IOITEM. DATA : IT TYPE STANDARD TABLE OF ABAPLIST WITH HEADER LINE. *DATA
-
[SOLVED] KDE 4.8 crash!
Hi! Yesterday, I updated my system, and installed the KDE 4.8. Today, when I started my computer, the KDE was with a grey wallpaper and big red squares, showing that the widgets was crashed too. I couldn't take screenshots, but I took some photos to
-
Multiple Ports for one Content in CSS
Dear All, We configure a CSS11506 (v5.2) and the enduser wants to setup only one content (vip address) to support multiple services (such as http, https and DNS). Since, in the configuration, we can only set one port in content rule. Is there any met
-
Hi EveryBody, I have to run an report from menu. the problem is i have an diffrent sizes of reports so i have to change the paper size everytime. for eg.( 1 report- A3transv 2 report- Germen SF )so is there any utility in form 6i through which i can