I seem to be missing DAQmx VIs?

I installed v 7.0, and then tried to run an example DAQmx VI from the developer zone. However, the VI can not start because a lot of DAQmx VIs seem to be missing. Doing a search on my Labview 7.0 directory, I do not find any VIs starting with DAQmx*.vi.
Furthermore, choosing Functions|input, I do not see the DAQ assistant (I think that is what it is supposed to be called?)
p.s. I am using the Prof devel system version/

Hey!
You have to download the DAQmx from http://digital.ni.com/softlib.nsf/websearch/BEC182021CEB566C86256EEE00696562?opendocument&node=132060_US
Josteid

Similar Messages

New Hardware / DAQmx Install, LabView 7.1 Now Missing DAQmx VI's?

Hello -
I've been running Labview 7.1 and some applications we've built with it for some time now. Due to an old DAQ board failure, we had to upgrade. Upon receiving the new (PCI-6225M) DAQ board, we had to update DAQmx (to 8.9.5) in order for this new board to be supported.
In doing so, it appears that the DAQmx VI's I had for Labview 7.1 were actually removed from the system. When I try to load my 7.1 applications, I get errors saying that it can't find various DAQmx VI's (like the DAQmx Create Task and Read VI's). Since it allows me to browse for them, I browse to the directory structures that *do* have them now (intended for LV 8.2+, which we don't have). If I select these VI's they seem to be found okay, but then I get an error for each VI saying that it's only for a newer version of LabView, not v7.1.
So what gives? What can I do? Why on earth would a newer DAQmx installer actually go in and remove already existing files from my previous install that previously worked fine? I am not impressed. What should have been a simple board upgrade now appears to be setting us back some significant time.
Thanks,
Brett

Hi Dennis,
I also have common issue. I am using labview 7.1 with DAQmx version 8.8. Recently, I just bought the cDAQ-9178, which requires me to upgrade my DAQmx to version 9.4. After installation completed, I discovered all my DAQmx missing. My question is:
1. Do you have any patch to let me stay @ LV version 7.1 with the new DAQmx 9.5 without missing DAQmx vis? I need the new DAQmx to be able to connect with cDAQ-9178.
Thanks you for your time, Dylan

DAQmx vis missing

Hello,
I have installed DAQmx9.9.0 and cannot find the DAQmx vis neither in Labview or in instr.lib
In Max,
Help!
Solved!
Go to Solution.

What version of LabVIEW? Did you install DAQmx AFTER installing LabVIEW?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Missing DAQmx Create Task.vi among others

Hi all,
I'm trying to run a .vi made in Labview 8.5 using Labview 2012. I have the most recent version of DAQmx (9.5) installed, but it's unable to find the file DAQmx Create Task.vi, and if I chose to ignore it about 6 other files pop up that it is also unable to find. I have uninstalled and installed DAQmx on both my computer and two other computers running Labview 2009 to try and get this to work, but nothing seems to be solving the problem. Any ideas what might be going wrong here?
Thanks!

Are you trying to open the VIs using 8.5 or 2012? Are the DAQmx VIs in the palette?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

I just purchased a macbook pro and was wondering about an install disk. It seems to be missing some of the applications that should be on it from a fresh install. I was wondering if I would have to purchase a new OS and do a fresh install?

I just purchased a macbook pro and was wondering about an install disk. It seems to be missing some of the applications that should be on it from a fresh install. I was wondering if I would have to purchase a new OS and do a fresh install?

Ahhh, well you never mentioned that before. You need to contact your friend from whom you purchased the computer. He/She should have any and all install discs for any third-party software included as well as for OS X and the original pre-installed software.
Apple will gladly sell you replacements for any discs that did come with the computer originally, but they will not do anything for you because you purchased the computer used. If it's in warranty still, then you can get any warranty covered things taken care of through AppleCare:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support visit online support site.

How to get I32 enum text out of a control (i/p terminal config, active edge of DAQmx vis)

Hi,
I am using DAQmx VIs create channel.vi and sample clock.vi, they have inputs (input terminal configuration) and (active edge) both are I32 and have enum looking drop down options. i want to use those text values to put into my excel file, but they give out numeric codes related to respective option. is it possible to get the text as it is.
it is not an enum but I32 which looks like enum..
plz help..
Thanks
Solved!
Go to Solution.

Note: This assumes that you have an actual control on the VI. If you have a
block diagram constant, then that won't actually work. In this case to get the actual text you need to pick from list of text items. To further complicate things, the actual values that are generated are not sequential. You can use either a case structure or a 2-step lookup.
Attachments:
Example_VI.png ‏7 KB

Enhance/Color Adjust/Color variation, seems to be missing in PSE 12. Can I install another version of PSE to Macbook pro Maverick 10.9.3 that has that feature? I use it ALL the time...

Enhance/Color Adjust/Color variation, seems to be missing in PSE 12. Can I add/install another version of PSE to Macbook pro Maverick 10.9.3 that has that feature? I use it ALL the time... Thanks.

Enhance/Color Adjust/Color variation, seems to be missing in PSE 12. Can I add/install another version of PSE to Macbook pro Maverick 10.9.3 that has that feature? I use it ALL the time... Thanks.

HT201272 Hi guys...I have just got a new computer and want to get my library back up and running on it. However I seem to be missing some of my iTunes music purchases. Any ideas on how to get them back? They show up on my ipad but not my actual itunes acc

Hi guys...I have just got a new computer and want to get my library back up and running on it. However I seem to be missing some of my iTunes music purchases. Any ideas on how to get them back? They show up on my ipad but not my actual itunes account.

Hello there, Capricious13.
There are great pointers in the following Knowledge Base article. Depending on where you see the content and where you want to get it to, this should guide you to putting it in the right place:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
http://support.apple.com/kb/ht2519
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.

Multiple inputs and outputs using DAQmx VIs

Hello,
I am fairly new with the LabView programming language. I have a few training books that I have been reading, and I have been following online tutorials and reading the forums. However, I have come to a problem where I don’t see a clear solution. I am using LabView 2009 (9.0f3) and DAQmx VIs.
I am using a NI 9172 chassis PLC, with two 9201 AI cards, 9217 AI RTD card, 9472 DO card, 9263 AO card, and two 9237 AI Bridge cards.
I am reading eight analog inputs with the 9201 cards, two analog RTD inputs with the 9217 card, three digital outputs with the 9472 card, three analog outputs with the 9263, and eight analog inputs with the 9237 cards.
I wrote a simple program to test one digital output task, two of the analog output tasks, and a single analog input task. I put all of them in the same while loop, and it worked perfectly. However, when I add analog input tasks to the same loop, I get an error 200022. So I tested each sensor individually by changing the channel before each run. I searched error 200022 and found that this is because I cannot start another analog input task until the previous one ends. With this said, I don’t know how to acquire an analog voltage in the same task as an analog RTD voltage. Both inputs take different constants in the start task DAQmx icon.
Attached is my test program. It is titled “Test All”. This is the program I used to test the various sensors. I tested the input sensors one at a time, and it worked fine. A few tasks are written just to test functionality, and will be added to later. The data is only displayed on the screen. I will add triggers and data write to disk functions later. This program works now, but if I add more analog inputs, it will generate the 200022 error.
Can someone show me how to correctly write the code for multiple inputs and outputs using DAQmx? All training materials and tutorials I can find all show a single input or single output, not multiples of each. Thanks for looking.
-Randy
Attachments:
TestAll-NI.vi ‏32 KB

Hi RandyC,
The Knowledge Base article Using Different Types of DAQmx Global Channels in the Same Task goes into a little more depth of what Bryan is talking about, and it also includes some example code to help show what to do.
Hope that helps,

Can read TEDS in MAX but not with DAQmx VIs

Hi,
I have a cdaq 9181 with a 9234 accelerometer module. I have 3 teds equipped accelerometers connected to ai0, ai1, and ai2 repectively. In MAX, when I reserve the chassis I can read all three teds, no errors. When I do the same thing in labview (ie reserve the chassis, create a daqmx task, associate teds data with each physical channel, all with daqmx VIs) I can only read two out of three teds. The third one throws a "no teds sensor detected" error. This code has been in use for about four months now, though I just rewrote the calling VIs, and hasn't displayed this problem. I've attached a snippet of the task building VI for reference.
Any ideas what's going on?
Thanks.
Using LV2012 and MAX 5.3.1 running on Windows 7 32 bit.
CLAD
Attachments:
Build Daq Task Snippet.png ‏58 KB

Nope. That's a delete from array, length 1, index 3.
In any case, I eliminated that block since the string array wired to the for loop controls how many devices the VI attempts to configure. Same result, verified it was trying to configure ai2. Here's the updated snippet:
CLAD
Attachments:
Build Daq Task Snippet v2.png ‏54 KB

DAQmx VIs Timeout Problems

Hello,
I am trying to acquire 9 frequency input chanels thorugh PXI-6624 card.
I have 9 independent loops for 9 frequency counter chanels. I am able to read all the frequencies above 10Hz properly.
Now the problem is,
Sometimes there will be no pulses, and the Counter Input DAQmx VI will wait for timeout.( I have given the timeout of 1 sec). During this time my CPU consumption goes very high and I am not able to read any of the analog inputs too.
and say if similar condition happens to all the 9 frequency input channels then my software hangs.
I have tried using wait mode method but i wasnt able to read any frequency with it.
I have also read it that, when "Counter Input DAQmx VI is in timeout mode at that time we cannot make any other DAQmx VIs call". Please refer this link http://zone.ni.com/devzone/cda/tut/p/id/3166
Thanks,
Krunal

What version of LabVIEW? Did you install DAQmx AFTER installing LabVIEW?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

How do I enable Java? I seem to be missing a plug in.

I seem to be missing a plug in .How do I enable java?

You need Acrobat. Reader doesn't have the ability to enable Reader's signing ability in a document.

In past versions of FireFox there was a view option that allowed a change in size of fonts and objects on the screen temporarily on the fly. This seems to be missing from version 6.

In past versions of FireFox there was a view option that allowed a change in size of fonts and objects on the screen temporarily on the fly. This seems to be missing from version 6. It was very useful and needs to be added to version 6.

You can use "Ctrl +" and "Ctrl -" to zoom pages quickly and "Ctr 0" (zero) to reset the page zoom.
*http://kb.mozillazine.org/Zoom_text_of_web_pages
There are also page zoom buttons in the toolbar palette in the Customize window that you can drag on a toolbar.
Open the Customize window via "View > Toolbars > Customize" or via "Firefox > Options > Toolbar Layout"
*http://kb.mozillazine.org/Toolbar_customization
*https://support.mozilla.com/kb/Back+and+forward+or+other+toolbar+items+are+missing

HT4850 I seemed to have missed the whole ordeal of keeping my 10.4.11 os x powerpc up to date. Are these suggestions still viable as I have been getting all sorts of console errors which now seem to lead me to this researched destination?

I seemed to have missed the whole ordeal of keeping my 10.4.11 os x powerpc up to date. Are these suggestions still viable as I have been getting all sorts of console errors which now seem to lead me to this researched destination? The suggestions involve putting "sudo" in Terminal Application and I am assuming that with all the console errors now being generated by my "permissions fixer" that this might be the reason...missed the class and updates as I never had problems like these before and the technology is changing. Have a whole list of console errors if someone is willing to help as I also think I have hit the motherload as to the reasons why?!

I seemed to have missed the whole ordeal of keeping my 10.4.11 os x powerpc up to date. Are these suggestions still viable as I have been getting all sorts of console errors which now seem to lead me to this researched destination? The suggestions involve putting "sudo" in Terminal Application and I am assuming that with all the console errors now being generated by my "permissions fixer" that this might be the reason...missed the class and updates as I never had problems like these before and the technology is changing. Have a whole list of console errors if someone is willing to help as I also think I have hit the motherload as to the reasons why?!

.Exe Missing DAQmx subVIs

Hello everyone,
I built an installer for my .exe. I included:
1. NI LabVIEW Run-Time Engine 2012 SP1
2. NI-DAQmx Core Runtime 9.6.2
3. NI-DAQmx MAX Configuration Support 9.6.2
The computer I made the VI is a Windows XP machine. The computer I want to run the installer on is a freshly-installed Windows 7 machine. When I attempt to run the installer, I get the following error:
Missing subVI DAQmx Create Task.vi... missing subVI DAQmx Create Channel (TEDS-A1-Voltage-Basic).vi... Missing Timing (Sample Clock).vi... Missing Control Task.vi... Missing Clear Task.vi... Missing Stop Task.vi... Missing external function nilvaiu.*AQReadNChanNSamp1DWfm:C...
It looks like I'm missing DAQmx VI's, yet I included DAQmx in the installer.
Thank you.
Solved!
Go to Solution.

I know these sound like a no-brainer questions but, did you run set-up.exe from <Directory>volume? Can you open MAX on the target machine? If so what software components are listed? Did you reboot to finish installation?
My 8-Ball is screaming that this is a simple error that will involve a <face palm> moment.
Spoiler (Highlight to read)
I've had my share of them too.......
I've had my share of them too.......
Jeff

I seem to be missing DAQmx VIs?

Similar Messages

Maybe you are looking for