I think my HDD is dead - stuck at the grey screen, with the apple logo ..

Hi all,
I think my Mbp's HDD has partially failed. It is the original 100gig drive , which was 95% full.
It started getting incredibly slow so I decided to reboot it. It has not been possible to boot.
I have managed to connect the internal drive to another mac using FireWire and T on startup.
The drive shows up and the data can be accessed albeit slowly.
I tried to repair the drive in disk utility and it came up with a lot of " invalid node structures" and " invalid record counts".
The disk utility seemed to not complete the process so I had to quit it.
I can't boot from the cd , but I may be doing it wrong.
Can anyone help me with the next thing to try?
Thanks.

Slow access even with Target Disk Mode (TDM) can indicate a failing drive, but it's possible that drive can be rehabilitated by continuing to off-load files and keep trying with Disk Utility. Sometimes, enough DU runs can restore sanity.
I'd check the SMART status first (try: SMART Utility at Apple OSX Downloads ). This can be done from the other Mac while the MBP is in TDM. If the drive passes and you can off-load some of the load, then a directory repair utility like DiskWarrior might be worth a try.
However DiskWarrior is US$100 and you can get a new 500GB SATA 2.5" hard drive for less than that. The advantage to disk Warrior is that it's easier to install in an MBP than a new hard drive.

Similar Messages

TS2570 my imac 27 inch 2011 is not booting up, the i mac is stuck on a gray screen with no apple logo or anything

my 27 inch 2011 iMac is not boting up, the cumputer is stuck on a grey screen with no apple logo or spinnign wheel. The iMac is not giving power to the keyboard as it is not ligthing up the caps lock botton when pressed.

Contact Apple Service, iMac Service or Apple's Express Lane. Do note that if you have AppleCare's protection plan and you're within 50 miles (80 KM) of an Apple repair station, you're eligible for onsite repair since yours is a desktop machine.

Computer crashed and is now stuck on a grey screen with the apple logo and pinwheel. What do I do?

Computer crashed and is stuck on a grey screen with the apple logo and pinwheel turning
Please help

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
     a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

I was installing the new EFI software update on my macbook pro and I became stuck on the grey screen with the window that said "installing 2 items", its been on the same screen for 2 1/2 hours. does anyone know what I can do?

As the title says.
I was installing the new EFI software update on my macbook pro and I became stuck on the grey screen with the window that said "installing 2 items", its been on the same screen for 2 1/2 hours. does anyone know what I can do?
I don't want to restart it because im scared that something might go wrong.
operating lion

LimitLess- wrote:
Hi,
I had the power supply connected when I attempted it previously but even so my problem occurred. My rom is different and so I still need to update it.
Thanks
I wanted to mark your answer helpful too but I didn't know that I could only put it for 2 answers. Sorry
That was good advice by G-N and s/he is correct about it. Unfortunately, ASC allows only 2 "helpful" and 1 "correct" marks per thread.

My Mac won´t load. When I turn it on, I type the password, then it starts to load, but nothing happens. It gets stuck on the grey screen with the apple logo. I can´t go to an Apple store since I´m working in Bolivia. Thanks

When I turn it on, I type the password, then it starts to load, but nothing happens. It gets stuck on the grey screen with the apple logo. I can´t go to an Apple store since I´m working in Bolivia. Thanks

RhysWills1,
which model MacBook Pro do you have, and which version of OS X is installed on it?

I updated my MacBook Pro, and now it's to fully restarting.. It's stuck on the grey screen with the loading sign at the bottom of the apple.

How do I fix this issue???

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

IPod Stuck on the Black screen with White Apple logo

Last night, my iPod suddenly stopped working after I restarted my PC with the iPod still connected to it. It's now stuck on the Apple Logo screen and keeps on making hard drive noises, as if it's constantly being reset.
I tried doing the Select+Menu button reset multiple times, and tried restarting my computer, connecting the iPod to different power sources, etc.
I'm unable to do a system restore because the iPod won't connect to my PC.
ANY help would be greatly appreciated, I don't want to lose this iPod

All you can do is to restore the iPod.If it happens again try restoring to factory defaults/new iPod, not from backup.

Please HELP, Stuck on grey screen with Old Apple Logo in it

Hi , my computer froze today and when I tried to reboot the hard drive starts but stays on a grey screen with a small folder in the middle with an Apple logo in it.
What should I do, all suggestions welcome!

Hi, and welcome to Apple Discussions.
Here are links to a couple of articles on recovering from the flashing question mark folder:
http://docs.info.apple.com/article.html?artnum=58042
http://www.bombich.com/mactips/openfirmware.html
I hope something there helps.

Help! I'm stuck on the white screen with the gray apple!

I just got an iMac g3/500 indigo, I think it has OS 10.0.4 installed. When I first turned it on it started fine and went to the password page. I did not have the password so I turned it off called the person I got it from, got the password. When I turned the G3 back on all I now get is the white screen with the gray apple. I tried to start in safe mode, it starts to load but then tells me I need to restart. I do not have the original disks, I do OS 10.3.2 disks but they are the DVD version and do not seem to work on this G3. What can I do? I am stuck, can someone please help? Thanks

Hi Frey
If your indigo has firewire (which I think it will have) see if you can borrow an external firewire DVD-drive. You can boot the iMac from that.
There may be one slight problem though with firmware (not firewire). I forget at the moment which version it is but installing 10.3 (I think) without updating the firmware first gives you blank screen and renders the mac unusable until you can get it fixed.
The problem is that firmware can only be updated while running OS9 "from the internal HD".
You end up with a catch 22 situation where you need OS9 CDs in order to install OS10.
The likely-hood of the iMac NOT having OS9 on it already is slim - no-one in their right mind would run an imac solely in 10.0. So you have to work out a way of getting started in 9.
See if you can locate an OS9 start-up CD - doesn't have to be an Apple one- Norton Utilities or TechTool Pro will do. Just get the mac started and then go to the control panels (under the Apple menu) and select start-up disk. It should (after a pause or two) show you all the viable startup systems on the mac. If you still can't get going you may have to rebuild the HD using one of the aforementioned utilities disks - though I would use DiskWarrior for that in preference to both of the others.
Let us know how you get on.

My apple wont turn on. it gets stuck on the gray screen with the spinning wheel and the apple on the screen

My macbook air turns on but not completely, it gets stuck on the grays screen.   It shows an apple an a spinning wheel and that is as far as it gets. sometimes I can get to an screen that shows macintosh hd and i clicked on it and the computer turned off.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
     a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

HT4623 so i downloaded the iOS 7 onto my computer. then wanted to upgrade. iTunes is waiting to connect to the phone after the restart. now it's stuck in the black screen with the white apple with the progress bar. then i look to iTunes and found out it s

so i downlaoded the iOS 7 onto my iTunes. then i wanted to upgrade. the phone is stuck in the black screen with the white apple and the progress bar. next time i click on iTunes, it says my phone "has an error and cnanot update" and now it is stuck on the black screen with the white apple and the progress bar almost finished. hasn't moved in 20 minutes.

No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

My macbook is stuck on a grey screen with language select and every time i click english it brings me back to the same gray page what do i do?

My macbook Pro is stuck on a grey screen with language select and every time i click english it brings me back to the same gray page with language select what do i do? Also i dont have enough monet to go to the apple store to get it fix and another thing this happen after i tried to factory reset it without the disck uising coomans i found on youtube.Lastly befor doing the comands my macbook would open any applications and the finder would just blink on and off on the dock.
Heres the link http://www.youtube.com/watch?v=Q5e5thk0O9o

Shut down your computer and disconnect all peripherals (keyboard & mouse if pertinent) from your computer. Now reboot.
If the Mac starts up normally, shut it down again and then plug in one of the peripherals (keyboard or mouse first) and start up your computer again. If it does so successfully repeat the process, adding one peripheral at a time until your Mac acts up. At that point, disconnect the last peripheral you added, reboot your Mac and search the peripheral vendor's website for an updated driver.
If no driver exists or the problem remain after installing the new driver, try a different cable or a different port on your Mac.
If none of the above works, again disconnect all peripherals from your Mac, hold down the "shift" key to start up in "Safe Boot" mode.
If the Mac starts up correctly, restart without pressing the "shift" key.
If your computer still does not start up properly, shut it down and restart it while holding down the Apple+Option-P-R keys; keep holding "all 4 keys" down until you hear the startup sound "twice."
If none of the above work Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
(If Disk Utility cannot repair, you will need a stronger utility (3rd party) - Diskwarrior or Techtool PRO)
Restart your computer when done.
Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.
Remove any 3rd party ram.
Reinstall Leopard - This will install a "fresh" copy Leopard without archiving old system files but leaves the rest of your files in place.
If you still want to restore your computer to factory level...
Start up from your install disc, go to Disk Utility and select the disk and click erase - to securely erase data click Security Options and Erase Free Space which will entirely wipe your disk, overwriting it with zeros so that no data is recoverable.
To restore read the instructions in the Mac OS X v10.5 Leopard - Installation and Setup Guide PDF

Plugged the charger in the wall, it gives me a black screen then the white screen with the apple logo, then repeat.... i tried the dfu thing and now the phone is saying connect to itunes, when i plug the phone outta the wall, the phone goes dead..... pl

i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s...
plugged the charger in the wall, it gives me a black screen then the white screen with the apple logo, then repeat....
i tried the dfu thing and now the phone is saying connect to itunes, when i plug the phone outta the wall, the phone goes dead.....
plugging the phone into the laptop NOTHING!!!!!!!!!!!!!!!!!!!!!
the laptop doe read my phone.....
no ding.....
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going on

mariidb wrote:
i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s... {snip}
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going on
That's the problem. That's what the **** is going on.

My iMac won't boot up fully. It stays stuck in the gray screen with the pinwheel spinning, then after about 5 minutes just shuts itself off.

My iMac won't boot up fully. It stays stuck in the gray screen with the pinwheel spinning, then after about 5 minutes just shuts itself off.

Try SMC Reset (unplug it from the back of the computer for 10 seconds then plug it back. in)
Try PRAM Reset Cmd + OPtion + P + R on start up.
Try safe boot - hold down shift on start up.
Try booting to install dvd (C on start up) or recovery hd (CMD + R) and using disk utility to run a verify and repair. If you still can't boot after that reinstall the operating system. If you can't find the disc or it wont boot to the disc.
Try single mode which is cmd+S on start up. It will open with a terminal looking window in the terminal. type in /sbin/fsck -TL. If it returns *system has been modified* continue to type that command in until it comes back with macintosh hd seems to be ok. If after 5 tries it still gives you system has been modified. You may have to replace the hard drive.

I jailbreaked my iPhone 5 and now i don't want the jailbreak any more so i restored the iPhone without iTunes an now i don't wad then it turned itf off and now its stuck on the black screen with the loading sign. So please how can i turn my phone on again

I jailbreaked my iPhone 5 and now i don't want the jailbreak any more so i restored the iphone without iTunes and then it turned it self off and now its stuck on the black screen with the loading sign. So please how can i turn my iPhone on again?

I figured it out by pressing the home button and the off button but when i turn my phone on again it's not restored. And when i try to restore it with iTunes it has to update but i can't update my phone because it's jailbreaked but if i can't update it, it won't restore the phone.

I think my HDD is dead - stuck at the grey screen, with the apple logo ..

Similar Messages

Maybe you are looking for