I tried a lot to overcome problem but it remains same
i also previously mail my question and got answer, i follow all the steps of my response but the problem is not gone.
my problem is that iam using daqpad-16xe-50-mio.i have 4 pads of same kind.out of four two pads r not working properly,they give the message of " your device are not working on th selected base address"
when i put the other daqpad which is right then that daqpad works absolutely fine but 2 out of 4 daqpad gives me above message.on the same parellel port address and irq two pads working fine and two gives message "your device not working on the selected base addres"or error -10805.please help me how this problem may be corrected.
Malik;
As you have four of the same DaqPad, have tested all four with the same setup, and two of them are not being recognized, everything is pointing to a hardware problem on those two DaqPads. If that is the case, the only way out is to send those failure Pads to get fixed by NI.
Hope this helps.
Filipe
Similar Messages
-
Macbook pro will not boot. I get the gray screen, an apple icon and spinning wheel. I tried to start in safe mode, but get this same screen. The only thing different is that I added the zedge update app to do a sync for adding ringtones to my apple cell phone. How can I get a good boot. I am fairly new to apple computer.
Reset PRAM: http://support.apple.com/kb/PH4405 and then try a normal boot.
Run the Startup Manager to select Startup disk: http://support.apple.com/kb/HT1310
If those did not work your disk may be sick or dying. The top priority at this point is to make a backup copy of your data.
Check the health of the disk. Boot in Recovery Mode (Boot, Command-R). Run Disk Utility. Click on the upper left disk icon. Does the S.M.A.R.T. status say “Verified”? If not the disk/SSD is unhealthy and needs to be replaced. Even if it does not show “Verified” you can still attempt a backup.
Click on the icon indented below, usually called “Macintosh HD” and Verify Disk. If it finishes with a green “OK” message then all is well with the disk. If it shows errors in red then you have found a problem to address once the system is backed up. Do not attempt software repairs until you have secured the data.
If the disk will not show up at all in Disk Utility as your ran the tests above then it may be dead or it may have a bad internal SATA cable. A trip to an Apple store for confirmation would be in order.
If you have an external disk drive you can use as a backup drive then do so. If not Google “Hitachi USB 3.0 external hard drive 1TB” to purchase one or go to a brick-and-mortar store (including an Apple store) to pickup one. Any 1 TB external drive will do.
Assuming it is still breathing you can try to recover the data without booting from the sick disk.
Reformat the external disk. (This will erase all data on the external disk.)
Boot in Recovery Mode. Start Disk Utility. Plug in the new disk. Select it’s disk Icon (the second one down, left justified). Select the Partition tab.
Partition Layout > Single Partition
Name: Emergency Recovery 1 (or whatever name you wish to use)
Format: Mac OS Extended (journaled)
Options… > GUID Partition Table > OK
Apply
Select the Restore tab.
Drag the old system volume (Macintosh HD) to Source.
Drag the new disk volume (Emergency Recovery 1) to Destination.
Click on Restore.
It may take a long time for the backup.
If that will not complete post back for other emergency data recovery methods, including those from a brody.
If the backup succeeds, use the First Aid tab in Disk Utility to select the old volume (Macintosh HD) and Repair Disk. If it does not finish with a green OK message try to repair it once or twice more. If it repairs with a green OK message, will it boot normally? If not, boot from the Recovery Partition and reinstall OS X.
If it is still not healthy, post back for further instructions. -
A message cannot be seen on my incoming emails. I can only view the message if I click on reply. Also any links attached to email will not open. I have tried everything to solve the problem but not able to.
Try closing the Mail app completely and see if it works properly when you re-open the app : from the home screen (i.e. not with the Mail app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Mail app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work also do a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot. -
qHow do u get help from apple support with iChat? I was able to chat with support last week to solve my problem but now the same issue is back and I don't see the option to chat now?
For what it is worth I have noticed a similar issue from the iPad3 while at work and home. At work we have two Apple TV 3rd Generation installed and tied to our A/V system. I believe the issue has to do with a timeout on the broadcast saying "here I am" and allowing devices to connect.
For example:
At work we have several Wi-Fi SSID being broadcast from Cisco APs. The only one we can use with the Apple TV is the one that uses a WEP since the others are either setup to be hidden, require web page authentication, or have a login requirement from employees. Essentially, what I believe the issue is that the Apple TV periodically broadcasts a message to other iOS devices that support Mirroring. When the Apple TV does not get a response from a device it goes into a dormant mode and requires either a command from the remote control or a reboot. This has been tested with both the power management enabled and not enabled with the same results.
As for when I come home, the Apple TV3 has not seen the device in some time and therefore is not broadcasting it's location information. A simple click of the circle or menu keys on the remote will give it the command to start broadcasting again and allow the iPad3 to see the Apple TV. When trying to Home Share the computer can not play (iTunes 11, Win8RTM) until the Apple TV is awoken then it will show up for mirroing.
This may or may not assist you but, it hopefully explains how the issue may be happening. -
I rented a movie on my Apple TV through iTunes. It shows that I rented it, but when I go to play it it there was an error, try again later. I have tried later, and later over days but get the same message! everything else plays, why not the movie (Maze Runner)?
What is your current connection via speedtest.net
Make sure DNS is set to auto (settings - general - network)
If on wifi try ethernet -
trying to download new software for ipad but get the same message coming up which is there was a problem downloading the software the network connection
timed out make sure your network connections is active or try again later. I have tried about 5 times to download this can anyone helpHave you disabled any firewall and security/antivirus programs? This seems to have helped the vast majority of people who have posted the same problem in this forum.
-
Have tried 4 times to reset, erase and restore but always the same result. Everything restores except my photos. When I go to photos at the bottom of the screen it says downloading but the pictures never transfer. Every time I turn my phone on it asks to continue restore but it never finishes. It won't let me upgrade to the latest iOS due to incomplete restoration.
How long has it been since you let the restore just happen? Sometimes photos are what takes the longest to bring back from an iCloud back up. I would recommend that you let it just keep restoring for about 2-3 days and see if more photos come back than what you're experiencing. Also make sure that you are connected to wifi as much as possible so that those photos can be downloaded faster. It is a waiting and being patient kind of thing. I did an iCloud restore from a backup that took 4 days to finish bringing down all my photos.
-
I am using OS 64 bit Windows Vista Home Premium and recently updated the latest version of iTunes. (I only have this CD burning software on my Laptop). Ever since updating, I received the message 'Registry settings for the iTune drivers are missing for CD burning'. The drivers for Lower and uppper filters in the registry are missingand I now have no optical drive. I have unistalled and reinstalled Itunes and manually entered the filters. Have tried everything including something called GEAR driver installer which was suggested on several technical sites. Everything was working fine in iTunes until I updated it.. It's strange I can still import music but not burn?? Friend s have told me they have ha dthe same problem when updating iTunes but resolved the problem by uninstalling/reinstalling or altering registry keys.
Today I went to use my Epson Printer and now have problems with it not working. I decided to uninstall/ install printer software and still can't get it to work either. I may be wrong but his all seems connected to me?
I have been trying for days to get telephone support and been told today you have to pay
Please can someone help me before I throw the lot out the window!!!!Many thanks b Noir
This is a copy of ONEof the keys in the registry I changed as told by Apple support today. I also have changed others as instructed by GEAR software support to manually delete GEAR drivers (that I had installed but couldn't delete some of the others they mentioned from Windows system 32. Then some bright spark at work told me I need the Gear drivers so I downloaded the software and installed again.
Sorry, just this minute went to insert image and it is giving me a message saying this sort of content is not allowed?.
The most recent key I altered is in: HKey _local _machine. System\class - 4D36E965-E325-11CEBFC1-08002BE10318. Upper Filter data: Upper filter NTIDrvr SiRem GEARAspiWDN.
The GEARsoftware info about manually deleting GEAR drive is from:
http://www.gearsoftware.com/wiki/index.php?title=DRIVERS:_Windows_-_Updating%2C_ removing%2C_64_bit_versions%2C_etc
I hope you can help -
I can't get my iTunes store to load. I can open iTunes, but my iTunes store is blank except for iTunes Store across the middle. How do I fix this?
Hi there steelgirl15,
I would recommend taking a look at the troubleshooting steps found in the article below.
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
-Griff W. -
I keep having popups, I have tried a lot to fix it but nothing works.
A friend of mine tired downloading a movie and I think I've got a virus from it. I keep having pop-ups and whatever I do nothing works. I don't know what I should do.
AdwareMedic 2.2.1 system report - Tuesday, February 3, 2015 @ 2:33:10 PM
Mac OS X version 10.9.5
14:33 up 1 day, 17:38, 1 user, load averages: 3.79 2.16 1.83
Safari extensions
/Users/arianarodrigues/Library/Safari/Extensions/wrc.safariextz
Name: Avast Online Security
Modified: Monday, February 2, 2015 @ 11:17:22 PM
Chrome extensions
/Users/arianarodrigues/Library/Application Support/Google/Chrome/Default/Extensions/aapocclcgogkmnckokdopfmhonfmgoek
Name: Google Slides
Modified: Monday, February 2, 2015 @ 11:18:33 PM
/Users/arianarodrigues/Library/Application Support/Google/Chrome/Default/Extensions/felcaaldnbdncclmgdcncolpebgiejap
Name: Google Sheets
Modified: Monday, February 2, 2015 @ 11:18:33 PM
/Library/Application Support/Google/Chrome/External Extensions/gomekmidlodglbbmalcneegieacbdmki.json
Name: [Unknown error extracting extension in CChromeExtension.GetNameFromCRX]
Modified: Monday, February 2, 2015 @ 11:17:17 PM
Firefox extensions
/Users/arianarodrigues/Library/Application Support/Mozilla/Extensions/{ec8030f7-c20a-464f-9b0e-13a3a9e97384}/[email protected]
Name: Avast Online Security
Modified: Monday, February 2, 2015 @ 11:17:23 PM
Login items
iTunesHelper, Spotify
Startup items
None
System startup items
None
User launch agents
total 32
-rw-r--r--@ 1 arianarodrigues staff 6148 Feb 2 18:20 .DS_Store
-rw-r--r-- 1 arianarodrigues staff 507 Feb 2 23:17 com.avast.home.userinit.plist
-rw-r--r--@ 1 arianarodrigues staff 542 Feb 2 22:52 com.spotify.webhelper.plist
System launch agents
total 8
-rw-r--r-- 1 root wheel 436 Feb 2 23:17 com.avast.userinit.plist
System launch daemons
total 24
-rw-r--r-- 1 root wheel 571 Feb 2 23:17 com.avast.init.plist
-rw-r--r-- 1 root wheel 685 Feb 2 23:17 com.avast.uninstall.plist
-rw-r--r-- 1 root wheel 694 Feb 2 23:17 com.avast.update.plist
Third-party kernel extensions
com.avast.PacketForwarder (2.0) <4 1>
com.avast.AvastFileShield (2.1.0) <5 4 1>
User cron tasks
None
Root cron tasks
None
launchd.conf contents
None
DNS settings
Server: 192.168.1.1
Hosts file
# Host Database
# localhost is used to configure the loopback interface
# when the system is booting. Do not change this entry.
127.0.0.1 localhost
255.255.255.255 broadcasthost
::1 localhost
fe80::1%lo0 localhost
Scan log
2015-02-02 20:43:53: ----- Scan Started -----
2015-02-02 20:43:53: Scanning with signatures version 50
2015-02-02 20:43:53: Buca Apps : /Users/arianarodrigues/Library/Application Support/webHelperApp
2015-02-02 20:43:53: Buca Apps : /Users/arianarodrigues/Library/WebTools
2015-02-02 20:43:53: ----- Scan Ended -----
2015-02-02 20:43:57: +++++ Attempting to remove adware +++++
2015-02-02 20:43:57: /Users/arianarodrigues/Library/Application Support/webHelperApp
2015-02-02 20:43:57: /Users/arianarodrigues/Library/WebTools
2015-02-02 20:43:57: +++++ Adware removal complete +++++
2015-02-02 20:45:31: ----- Scan Started -----
2015-02-02 20:45:31: Scanning with signatures version 50
2015-02-02 20:45:35: No adware found
2015-02-02 20:45:35: ----- Scan Ended -----
2015-02-02 22:22:33: ----- Scan Started -----
2015-02-02 22:22:33: Scanning with signatures version 50
2015-02-02 22:22:41: No adware found
2015-02-02 22:22:41: ----- Scan Ended -----
2015-02-03 14:13:20: ----- Scan Started -----
2015-02-03 14:13:20: Scanning with signatures version 50
2015-02-03 14:13:32: No adware found
2015-02-03 14:13:32: ----- Scan Ended -----
2015-02-03 14:30:22: ----- Scan Started -----
2015-02-03 14:30:22: Scanning with signatures version 50
2015-02-03 14:30:25: No adware found
2015-02-03 14:30:25: ----- Scan Ended ----- -
I have never had any problems before but all portrait photos added today have the top chopped off. For example , people's heads are missing or roofs or buildings are chopped off. Photos are fine on the camera and on my mac in iphoto and aperture. Switched off photostream on my ipad...all photos were deleted. Switched photostream back on and all photos uploaded again and portrait photos are cropped again
It sounds like while trying to import the photos with insufficient disk space those image files were damaged and not copied fully. Now that you have sufficient space (a minimum of 10 GB is recommended) the latest imports are good.
What do you get if you export one of the problem photos out of iPhoto as Kind=Original and try to open it with Preview. If it appears the same then there's nothing you can to do recover them.
OT -
I have several .m4r files I'm trying to upload to my "Ringtones" folder on my Iphone 3G. They Sync into the phone just as they should, so it appears. In Itunes, all 3-4 of the songs/ringtones are listed...however when I open the sounds folder in my Iphone, the same song has been copied 3/4 times! Even when I try to copy files over individually, it still doesnt work.
ANyone have any ideas???
Also, if I just drop one rington in my Iphone, then unplug it, that rington will take the place of another one, but BOTH of them will be listed in Itunes in my iPhone ringtone folder.
THis is CRAZY!
HELP!thanks for all the GREAT replies!
yeah...right. -
I have a photo with 25 faces. I have named 17 with no problem but the remaining 8 names I am unable to make them stick. I go through the process (have done it thousands of times) and no luck. I have shut down the computer, I have unplugged it, I have turned iPhoto off and nothing will allow me to name these remaining photos. I type in the name and click RETURN and the name holds, I close the photo and bring it back and the name is gone. I have done this dozen of times - still no luck. I have a few other photos of groups and the same thing is happening with just a few of the faces. All the faces are clear, same size and no different in clarity than the other faces. I have tried changing the size of the "box" around the photo to name it - still no luck.
I am on the ground floor so I can not throw the computer out the window.Im wondering why my post hasn't been answered yet. I did file a report with the BBB and I had a rude representative from Verizon call me named Steve. He said I can file all of the reports I want and I will just keep getting calls from him. I can understand why my phone couldn't be replaced because of the small crack. I guess I have to eat that one (but it sucks because the lollipop update is what caused the problems) but what about all of the data overage I had to pay for for trying to fix this phone because of a lollipop update. I dont think it is fair to have to pay that as well. In addition, because I have an east coast phone number but live on the west coast, I cannot have tech support after 8pm. Verizon has cut this off. Im very dissatisfied and I have been a customer of Verizon for 13 years. Im hoping for a response this time.
-
I Want to stop download of iOS 8 and start again
sorry, thought my question had been posted. I started downloading iOS 8 24 hrs ago, it is still downloading now, have tried off/on with 2 buttons but still the same can anyone advise please cheers
-
I rented a movie (dark shadows) but I can not see it, because a message appear "Problem loading...try again later". Is not a problem connection. I tried a lot of times to watch the movie and I didn't can.
Thanks
CelesteI rented a movie (The Hobbit)...but it stops loading.
The movie costs CHF 7.50.
A phone call to the support team costs CHF 46.-- !!!!!
What do you think I will do?
Pisella Verde
Maybe you are looking for
-
Hello, I'm having problems on the Lightroom CC App,as it seem's that when I open the Develop heading at the top of the screen,there is message that comes,which says this section is disabled and I need to renew my membership.My membership is up to dat
-
My report is printing half of the page when I print the report Hp psc 1315
My report is printing half of the page when I print the report in this printer Hp psc 1315 all in-one and when the operating system is windows xp , but when I run the same report in windows me , and the same printer it is running well And my report v
-
How to reconcile AR down payment Request with AR Invoice?
Dear All, SAP B1 2007A SP01 PL07 version. I have created one AR down payment Request with total amount 1000.00, and then post incoming payment to paid the AR down payment Request, and the AR downpayment request then closed. Then, I add one AR Invoice
-
Position the cursor on an ENHANCEMENT statement .ED301
Hello Folks , I am changing an ENHANCEMENT and did a syntax check. the syntax check failed. Editting is now locked out and when I place the cursor on the Enhancement statement and go to Edit > Enhancement Operations > Change Enhancement. the "Positio
-
What happens after downloading iPod Updater-after clicking restore?
I have a problem with my ipod that's a bit complicated and can anyone just help? See what happened was, my ipod was in a scan mode, so my cousin tells me. After the battery died, I recharged it, hoping it would stop but it didn't. The next day, all t