I tried to logon to 192.168.I.I as recommended, but got a fail

Hi,
This is my first post, so please be kind if the post is not placed in the right location.
My home gateway / vivid wireless "4G" account is a few years old, but it seems that the speed is getting slow more often, which is quite frustrating.
Looking on the forum, it is recommended to have a look at RSSI and CINR parameters, so I tried to logon to 192.168.I.I as recommended, but got a fail -1 error when entering logon details.
I followed http://www.192168ll.website/
Can you please help?
Thanks.

Hi webdangol223. First of all, it would be best if you can tell us the model number of your device. It is not clear if you do have a Linksys router because you mentioned about "4G". Anyway, if you do have a Linksys one and you are unable to access its setup page through 192.168.1.1, you may have to check from your Command prompt whether it really has that IP address as sometimed they get changed during the setup. Once confirmed and since you are unable to access the page through that, your last option will be to reset the unit to the default settings. Once done, access the setup page again.
To do the proper reset, please press the reset button on the router for 30 seconds, release the button and unplug the unit. Replug and try to access again.
Hope the above helps.

Similar Messages

I am trying to run page 192.168.0.170 for my IP Cameras but after login and password the page is not responding. Plz help!

I am trying to run page 192.168.0.170 for viewing IP Cameras but after login and password the page is not responding. Plz help!

I am trying to run page 192.168.0.170 for viewing IP Cameras but after login and password the page is not responding. Plz help!

Hi I installed a new hard drive in my Mac mini osx lion an when I turn it on I get a flashing file with a question mark. I tried holding command and R keys when turning it on but the recovery fails to work. Does any one know how I can get it to recover?

Hi I installed a new hard drive in my Mac mini osx lion an when I turn it on I get a flashing file with a question mark. I tried holding command and R keys when turning it on but the recovery fails to work. I can hold the option key at start up and choose my network, then Internet recovery shows up with an arrow pointing up. When I click on the arrow Internet recovery fails and all I get is a globe with a triangle on it with an exclamation mark on it, and under that it says
apple.com/support
-6002F
Does any one know how I can fix this without a recovery disc? Thanks

I just want to add to this, in case someone else searches for this error on Apple Support (google doesnt cover apple support.. how clever is that?)
I had the same error. And i had a Computer that had worked, with a SSD drive and 16GB upgrade done by the owner himself.
I tried swapping with a Mechinal Harddrive, no luck.
Kept the Mechanical drive in, and tried with some other Ram, it worked..
So for me this error and after reading the other responses can be boiled down to a Harddrive problem or Ram issue.
It was Ram for me..

Hi Guys, Im trying to send a 80pages IPhoto book to the store but the uploading fails, I tried several times and always a message "an error occurred" without clarification, can you help me?

Hi Guys, Im trying to send a 80pages IPhoto book to the store but the uploading fails, I tried several times and always a message "an error occurred" without clarification, can you help me?
Is there any size limit? or a limit of time to upload? (as it takes more than one hour!!!)

Preview the book -
Before ordering your book preview it using this method - http://support.apple.com/kb/HT1040 - and save the resulting PDF for reference - the delivered book will match it.
if it is good boot into safe mode, preview again (only limited fonts are loaded in safe mode) and upload
LN

Im trying to install new version of itunes in my macbook but its always failed .i can download but cannot install says to contact with software manufacturer assistance....please solve my problem because of this i couldnt connect my iphone to my mac.....

im trying to install new version of itunes in my macbook but always failed.i can download it but failed to install and always says to contact with software manufacturer for assistance...please heblp me i couldn’t connect my iphone to iktunes..please coz in my mac their is old version of i tunes.....

Welcome to the Apple Support Communities
See if your computer is supported > http://support.apple.com/kb/sp575 Buy Snow Leopard > http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard Then, make a backup, insert the DVD and upgrade. Finally, go to  > Software Update and update to the latest version.
If your computer is compatible, you can use Mountain Lion. Open App Store and purchase Mountain Lion. Check if your programs are supported > http://www.roaringapps.com

I have an iphone 4 and have tried updating to IOS 6 via my laptop and phone but it keeps failing why is this and what do i do

i have an iphone 4 and have tried updating to IOS6 via my laptop and phone but it keeps failing why is this and what do i do ????

Find the .IPSW file that was downloaded and delete it, then re-download it.
If you're using a PC, shut off your antivirus and firewall software during the process.

I tried downloading Adoboe Photoshop CC and it says: Installation succeeded but a patch failed. How do I fix this?

Let me explain. I have an HP 2000 series laptop running Windows 7 Home premium with a 500gb hard drive. I currently have Adobe Photoshop CS4 on my computer but I uninstalled it first before downloading the trial of CC. I figured when my 30 day Photoshop CC trial was over I could go back and download CS4 with the CD again. I just wanted to try CC to see how different it was from CS4 and for some reason when I install it gets to 99% and when it finally reaches that 100% the error message comes up "Installation succeeded but patch failed." I have tried to hit the retry button a number of times and each time it still gives me the same error message. I tried restarting my laptop to see if this would fix the issue and it did not. What does this "patch failed" error mean and how do I fix this so I can download my adobe photshop CC trial?

Yeah for some odd reason out of no wear i am able to successfully download everything. Ill be honest i couldn't download everything properly while watching Netflix. ha Weird. But yea i just got Photoshop and flash to download fine! so thats awesome thank you for the tip i will be sure to add that next time i have a problem thank you!

My ipad1 won't turn on - the battery was not dead - I tried holding in the home button and the start button but got no response - just a black screen

My IPad 1 won't turn on - I have tried the tip of holding the start and the home button for 10 seconds - nothing happened. The battery is also not dead. Please help. It has been 2 days!!

I reccomend bringing it to the Apple genius bar.
Try to connect to iTunes, and if it works restore it.

Trying to get online help. Entered correct serial no. but got error message "Incorrect serial number" - what to do next?

Can anyone help me with this issue?

If you mean by online help Apple's Support, formerly Apple Express Lane, then follow rack0's advice. If not, then provide the link where you're having the issue.

I cannot access 192.168.1.1

Hi,
This is my first post, so please be kind if the post is not placed in the right location.
My home gateway / vivid wireless "4G" account is a few years old, but it seems that the speed is getting slow more often, which is quite frustrating.
Looking on the forum, it is recommended to have a look at RSSI and CINR parameters, so I tried to logon to 192.168.I.I as recommended, but got a fail -1 error when entering logon details.
I followed The instructions of 192.168.l.l | 192.168.1.1
Can you please help?
Thanks.

Hi webdangol223. First of all, it would be best if you can tell us the model number of your device. It is not clear if you do have a Linksys router because you mentioned about "4G". Anyway, if you do have a Linksys one and you are unable to access its setup page through 192.168.1.1, you may have to check from your Command prompt whether it really has that IP address as sometimed they get changed during the setup. Once confirmed and since you are unable to access the page through that, your last option will be to reset the unit to the default settings. Once done, access the setup page again.
To do the proper reset, please press the reset button on the router for 30 seconds, release the button and unplug the unit. Replug and try to access again.
Hope the above helps.

Can't configure Airport Extreme with IP 192.168.0.1 after software update

Hi there,
after updating my ax with utility software 5.3.1 and firmware 7.3.1. The software didn't allow the dhcp configuration to stay at IP range from 192.168.0.40 to 192.168.0.200
The message said that this is not a valid IP.
The configuration was working before without any problem.
After several tries I changed to 192.168.1.40 and 192.168.1.200. Now I was able to save the changes. And the airport is working well.
But I can't go back to 192.168.0
But I need to use 192.168.0 for a tunnel to connect to my wifes company.
Configuration:
Seperate Modem with DSL.
Connecting over PPPoE
Activeted WLan
Connected computers over Lan and Wlan
Can anybody help?
Thanx
Stephan

by-feet, Welcome to the discussion area!
AFAIK the AirPort Extreme base station (AEBS) has always forced the 3rd digit to be a 1 (one), as in x.y.1.z.
Could it be that you previously had the AEBS to operate as a bridge and your "modem" was actually suppling the IP addresses?

Can't open 192.168.1.1 during setup

I am replacing a Netgear wireless router (WGR614v10) with a Cisco WRVS4400N. When I go to set up the device on my Mac, 192.168.1.1 will not open in a browser. Do I have to do the setup on a PC? Or, am I doing something else wrong?

Hi Jon, first, factory default the unit holding the reset button for 30 seconds. Verifiy on the unit the diagnostic light is not on. Verify the port light is on for the port your computer is connecting to. Open a Terminal and trying to ping the 192.168.1.1. You may also check your network adapter to ensure you're receiving DHCP from the unit. I know on some MAC computer, you have to set your connection preferences. If you've been using wireless, open your network connection and choose your ethernet as primary connection. MAC sometimes does not work using a wireless + ethernet simultaneously.
-Tom
Please rate helpful posts

I tried to update to the most recent itunes, but the update failed and now when I try to open itunes a dialog box pops up and tells me that it can.t open because MSVCR80.dll is missing. I need help!

I tried to update to the most recent version of itunes but the update failed. Now when I try to open itunes I get a dialog box telling me it can,t open because MSVCR80.dll is missing. I tried uninstalling and reinstalling itunes but I grt the same message. What can I do to fix this?

Solving MSVCR80 issue and Windows iTunes install issues.
Thanks to user turingtest2 for this solution.
Solving MSVCR80 issue and Windows iTunes install issues.
If the above doesn’t do the trick entirely, then use the instructions in the following as it applies to the version of Windows you are using:
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
You may be required to boot into safe mode to complete the folder deletion process.

I'm trying to install the Camera Raw plug-in into Photoshop CS5 but it keeps failing

Hi - I'm trying to install Camera Raw plug-in into Photoshop CS5 but it keeps failing - I don't keep any reasons at all. The product is registered - please help!

Which version of Camera Raw? Which camera?
Familiarize yourself with these two tables
Camera Raw plug-in | Supported cameras
Camera Raw-compatible Adobe applications
They tell you which version of Camera Raw is required to support your camera. The also tell you which version of Camera Raw is compatible with your CS5 (up to version 6.7 only).
It may be that the version of Camera Raw you need is not compatible with CS5.

Can't connect to 192.168.1.1 with my macbook. Tried reading all the posts no luck.

I've read through tons of posts and still no solution. I have powered everything on and off. I've tried firefox, safari, and netscape. I still cannot connect to 192.168.1.1 I have a befw11s4 v2. Along with not being able to connect to the setup page, my internet signal strength goes up and down constantly even though I am right next to the router.

If something does not work there is usually an error message which explains the problem. Please post the exact error message you get.
When wired to the router, open a terminal window and enter "ifconfig en0". Please post the output of that command.
Next enter "ping 192.168.1.1" and post what happens. Again, if there is an error message post the exact error message.

I tried to logon to 192.168.I.I as recommended, but got a fail

Similar Messages

Maybe you are looking for