I tried to restore my ipad mini and it didnt work now it doesnt turn on or work and I tried to hold the sleep button and the home button for 10-15 seconds and it didnt work now i dont know what to do !!!!!!!
i tried everything everyone told me,still doesnt work help with my problem please
If it has NEVER been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless. It is likely what you already tried but I want to be sure...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this.
Similar Messages
-
trying to restore my ipad mini it gets to itunes so far then says can not find device
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
spent hours trying to restore my ipad mini but it just keeps kicking me out halfway through the update followed the error codes etc... but no further forward
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
Cheers, Tom -
Hi Everyone,
This problem just started today. When I turn on or restart my Macbook Pro Retina 15" (Mid 2012 version), my screen is light gray like normal, and then after a few seconds my entire screen flashes completely bright yellow for a few seconds, and then it goes to the normal Welcome screen (where I choose to login as myself or a guest user). This suddenly started today and has not stopped since. This keeps happening every single time I turn on or restart my computer.
Yesterday I installed all the Mavericks and other updates that were available in the App Store, so I'm wondering if this is related to that since this never happened prior to my doing those updates yesterday. When I first installed the new OS X Mavericks (10.9.3) update, it went through the whole installation process (took about 10 minutes), and then during the installation I got an error message saying that it couldn't verify my iTunes application that was on my laptop, and then my laptop finished installing the updates. Then once my laptop restarted, the App Store "Updates" section said that I had to do the whole OS X Mavericks (10.9.3) and iTunes (Version 11.2) updates all over again. So my laptop did the whole installation again (took about 10 minutes, but this time I didn't get that "iTunes error message" during the installation process).
Now, when I go to the App Store "Updates" section, it says the following under "Updates Installed in the Last 30 days":
-Digital Camera RAW Compatibility Update (Version 5.05) installed May 15, 2014
-OS X Update (Version 10.9.3) installed May 15, 2014
-iTunes (Version 11.2) installed May 15, 2014
-OS X Update (Version 10.9.3) installed May 15, 2014
-iTunes (Version 11.2) installed May 15, 2014
-Security Update 2014-002 (Version 1.0) installed April 22, 2014
I'm wondering if this flashing bright yellow screen upon bootup is related to the fact that my laptop installed the OS X Update and the iTunes Update two times each? Or is this new problem totally unrelated? It's just that this problem started a day after these 2 updates were installed twice.
My Macbook Pro Retina 15" (Mid 2012 version) is otherwise working fine at least as of now. The only issue so far is this flashing bright yellow screen every time I turn on or restart my computer.
If anyone could please help me fix this so that my bootup screen doesn't flash completely bright yellow anymore, I would be forever grateful!
Thank you so much for reading this and for any help you can provide.
hope everyone is well,
ElaineHey everyone in Apple world!
I figured out how to fix the flashing yellow screen problem that I've been having on my MBP! Yessssss!!!
I found this super handy website with the golden answer: http://support.apple.com/kb/HT1379
I followed the instructions on this page and here's what I did:
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
I went through the 6 steps above twice, just to make sure I got rid of whatever stuff was holding up my bootup process. Since I did that, my MBP boots up just like normal. No flashing yellow screen anymore!!
(Note that I arrived at this solution when I first saw this page: http://support.apple.com/kb/TS2570?viewlocale=en_US)
Let me know if this works for you!
Elaine -
Tried to restore my iPad mini that wouldn't turn on and now it wont do anything.
I was trying to update an app and it wouldn't update so I restarted my iPad mini. Well when I restarted my iPad it would only load to the apple screen and then nothing would happen. I came on here to see someone said to restore the iPad mini and it gave me steps on how to restore it so I folowed them and it was all going well. Well after the first attempt it hadn't been restored yet so I went to do it again but it never showed the iTunes screen but it would show the apple sometimes. I was tired of trying because it was getting very late and I wanted to sleep so I just set it down. This morning I wanted to try again because this iPad mini was very essential to my everyday life and now I can't get it to do anything. When I plug it in the computer the computer doesn't even say anyhting and I honestly don't know what to do. I spent too much money on this when it came out for it to break because it couldn't start up.
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
Cheers, Tom -
HT1212 when trying to restore my ipad mini i keep getting a message that says network has timed out
When trying to restor my I pad mini that has been disabled I keep getting a message saying connection has timed out. I have been working on this for hours. Someone please tell me in the simplest terms how to restore my ipad.
Try temporarily disabling your firewall and anti virus software and try again...
See here for Connection Issues
http://support.apple.com/kb/TS1379
From Here
http://www.apple.com/support/itunes/troubleshooting/ -
Firefox is gisteren beginnen raar doen, je opent de browser, de startpagina komt er 2 seconden op, en dan verdwijnt die, ik krijg dan een wit scherm, en het is zo bij elke pagina die ik open, (facebook, youtube....) Wat kan dit probleem zijn?
Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* On Windows you can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac you can open Firefox 4.0+ in Safe Mode by holding the '''option''' key while starting Firefox.
* On Linux you can open Firefox 4.0+ in Safe Mode by quitting Firefox and then going to your Terminal and running: firefox -safe-mode (you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
[[Image:FirefoxSafeMode|width=520]]
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you. -
i tried to update my ipod but then it didnt work saying that an unknown error has occured, now itunes is not recognising that an ipod has been plugged in and the picture that comes up when you first get it (an arrow leading to the itunes sign) is on my screen, i dont know what to do?
Error 1604
This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for the error.
When prompted, click OK.
Close and reopen iTunes while the device remains connected.
The device should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Error 1600, 1601, 1602
Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software. -
I need help. My ipad 2 was stuck in recovery mode. i tried to connect it to itunes and restore but after downloading the file and extracting the software there is a pop up message that says "the device is full. Deleting files and emptying your recycle been will help you restore." how am i going to erase files if i can't open my ipad. i dont know what to do. Its been 2 days now. please help. thanks.
yes i am sure. This are the exact words... "The iPad "iPad" could not be restored. The disk you are attempting to use is full. (Removing files and emptying the recycle bin will free up additional space". i tried some options, hard reset, redsnow, tinyumbrella but still it's stuck.
-
Updated iPad 1 to IOS 5. When trying to restore my iPad from my backup it gets half way through and the iPad reboots and iTunes says "An error occurred while restoring this iPad (-1)"
I have tried to restore my contacts and company data at least 20 times and every time half way through THE iPAD REBOOTS! When it boots back up it is at the brand new iPad screen.
This makes me angry as I do not use the iPad for fun and games. I use it for business. My company data and records for the last year are gone. ALL of my out standing customer invoices are gone. ALL payments received are gone! ALL Business contacts and emails ARE GONE! All my company, personal email accounts and settings ARE GONE!
What am I supposed to do now? In 6 hours I have to get on the road and conduct business with a empty blank factory out of the box iPad. How am I supposed to know who owes me money or who has paid their bills Apple? All of my meetings and calendar dates are GONE!
Everything was supposed to be backed up and restored after the update!
Question???WHY DID YOU MAKE THIS UPDATE WIPE OUT ALL SETTINGS AND APPS ON THE iPAD??? All the other updates left everything on the iPad intact and ONLY upgraded the IOS,and when it was done everything was still there.
Yes! I have done everything. Rebooted computer, checked for updates, Hard booted iPad, Factory restored iPad to ios 5 twice, tried every usb port I have, unplugged all other usb components.
Everytime half way through "Restoring iPad from backup..." The iPad turns off shows a spinning circle then shows the Apple logo and takes me to the brand new iPad setup screen.
Apple, you have no idea the level of stress you have created today.....Check the console app to see if there are any error messages. I had one app showing an issue (Pet Hotel) the error was (truncated):
ERROR: Restore message response: 102 rename error: File name too long (63) at path "/var/mobile/Library/SafeHarbor/com.pocketgems.tappethotel/Container/Documents/ savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHis tory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGa meHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/sa vedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHisto ry/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGame History/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/save dGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory /savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHi story/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedG ameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/s avedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHist ory/savedGameHistory/1313349538-pocket_gems_crash_report.txt" (MBErrorDomain/102)
I manually snyc'ed that particular app and then re-ran the restore and am now the proud owner of a working iphone. Not sure it is the same problem or app but looking in the console was the key! -
After I tried to update my Ipad mini to the newest update, it kept saying hello on my lock screen in different languages and then when I slide the screen across, it says connected to itunes but it's not doing anything!! By the way my Ipad mini is plugged into my computer and connected to itunes!! Please help me!!
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY. -
In case this doesn't show up....I am trying to restore my ipad due to the fact my girls forgot passcode....when I hook up to PC and try to incorporate itunes, it will not come up maybe because I have no itunes on my ipad...can anyone give me any suggestions, as of now I have disabled the ipad trying for a passcode...
You do have iTunes on the iPad. You need to have iTunes on the PC because you need to restore it now.
You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
Try this ..... You will have to use recovery mode
http://support.apple.com/kb/ht4097 -
i had to restore my iPad mini and when I go to the App Store to reload some of my apps it times out and doesnt reload them. Any suggestions?
Close the App Store app and reset your iPad.
Now close all apps. In order to close apps, you have to drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
In order to reset your iPad, hold down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple logo appears on the screen after which time you can release the buttons and let the iPad start up.
IF that didn't help, try turning WiFi off on your iPad in the Settings, restart the iPad, then turn Wifi on again. -
I tried to restore my iPad from the cloud backup but the iCloud returned the following message 'no backup available'? This after happened after I created the backup today and the same was confirmed at the Apple Store attendant
Check the console app to see if there are any error messages. I had one app showing an issue (Pet Hotel) the error was (truncated):
ERROR: Restore message response: 102 rename error: File name too long (63) at path "/var/mobile/Library/SafeHarbor/com.pocketgems.tappethotel/Container/Documents/ savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHis tory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGa meHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/sa vedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHisto ry/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGame History/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/save dGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory /savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHi story/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedG ameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/s avedGameHistory/savedGameHistory/savedGameHistory/savedGameHistory/savedGameHist ory/savedGameHistory/1313349538-pocket_gems_crash_report.txt" (MBErrorDomain/102)
I manually snyc'ed that particular app and then re-ran the restore and am now the proud owner of a working iphone. Not sure it is the same problem or app but looking in the console was the key! -
My iPad suddenly started to show crazy colors. I turned it off. It would not reboot until I used the two-button reboot. Now it shows only green stripes. only for a few seconds and goes back to sleep. HELP!
Standard troubleshooting...
1. Try a Restart by pressing the sleep/lock button until you see the slider. Slide to power off. Restart by pressing the sleep/lock button until you see the Apple logo.
2. Try a Reset by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider if, it comes up. Takes about 5-15 secs of button holding and you won't lose any data or settings.
3. Remove all apps from Recently Used list...
- From any Home Screen, double tap the home button to bring up the Recents List
- Tap and hold any icon in this list until they wiggle
- Press the red to delete all apps from this list.
- Press the home button twice when done.
4. If still a problem restore with your backup.
5. If still a problem restore as new, i.e. without your backup. See how it runs with nothing synced to it.
6. If still a problem, it's likely a hardware issue.
Maybe you are looking for
-
AP check graphic design - R3 FCC 6.0
I need setup check layout for laser check printing in AP, how can I do it? Does SAP provide the import graphic for basic Laser Printer layout and we just need to edit a bit to fit on the check. We do not have Crystal report nor BW yet. I use canne
-
My JTable Column is not removing?
public class ClassA extends JPanel private DefaultTableModel model = new DefaultTableModel(); private JTable table = new JTable(model); public ClassA () { this.add(new Table1Panel() ); public class Table1Panel extends JPanel
-
We are using BPM 11.1.1.6. We are dealing with huge payloads and are storing the bulk of data in a separate schema outside of the BPM engine. This data will be surfaced via ADF-BC in a human task UI. I am looking for a method in the BPM API that expo
-
Can I use "g" and "n" AXs at the same time for Airtunes?
Hi, hope someone can help with this. I currently have a wireless "g" network made up of a Netgear DG834PN router handling DHCP and with wireless off, an AEBS "n" as a wirelss base station and 4 AXs (2 "g" and 2"n") doing extended wireless and airtune
-
Hi all, 11.2.0.1 Aix 6.1 We have PROD and UAT databases. Since all programs will be tested/qa on UAT first before porting it to PROD, I want to compare if the two database is identical in terms of what?(maybe objects) Is there a tool that compare the