I updated my ipod with IOS 6.1 Now it blinks the apple logo HELP!!!
After I updated my I-Pod with IOS 6.1 all it will do is flash the apple logo. I've tried shutting it down, but nothing stops it from blinking the logo. Except when I hold down the power botton and the Home botton at the sametime. Please can someone help me fix this problem. Thank you for your time :-)
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Similar Messages
-
i updated my ipod touch and it is not functioning. The logo is blinking and it doesn't turn off either. Any help?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I was trying to update my ipod to iOs 5 but I have forgotten the backup password
I was trying to update my ipod to iOs 5 but I have forgotten the backup password help please?
You need to restore your iPod to factory defaults/new iPod. That is the only choise.
Warning: If you encrypt an iPhone backup in iTunes and then forget your password, you will not be able to restore from backup and your data will be unrecoverable. If you forget the password, you can continue to back up and use the device, however you will not be able to restore the encrypted backup to any device without the password. You do not need to enter the password for your backup each time you back up or sync.
If you cannot remember the password and want to start again, you must perform a full software restore and when iTunes prompts you to select the backup from which to restore, choose set up as a new device.
Above from:
http://support.apple.com/kb/HT4946 -
My ipod touch 3 is blinking the apple logo on and off when i updated it to 6.1.5
i tried to update my sisters ipod touch 3 to ios 6.1.5, and now its blinking the apple logo on and off. is this nomal for updating?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
After updating my Ipod with IOS 5, some of my music no longer plays. Album cover is shown, but the IPod skips to the next song. Any ideas why?
A not uncommon problem. See this previous discussion.
Problems with IOS 5 Music App (Updated) -
Just updated my iPad with iOS 7 and now internet does not work anymore, how to fix if???? Desperate
Try resetting your iPad:
Double click the Home button. Slide up with one finger on ALL your apps to close them.
Then, Press the Sleep/Wake button + Home button and hold 15 seconds or until you see the Apple logo.
This will reset your device without erasing data, apps or settings. -
my ipod touch wont turn on ive tried restoring it but every time i do it just says its waiting for the ipod to respond. meanwhile my ipod is no longer a black screen but the apple logo with a loading bar underneath that after leaving for 8 hours hasnt moved.
Try:
- Another cable
- Another USB port
- Reboot the computer
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I have apple tv 5.21 and 4s phone with os 6.1.3 mirroring icon doesnt show i updated my itoons with my computer and phone i restored the apple tv settings to factory and still no mirroring option my apple tv software is 5.2.1
Hi there,
You're running an old version of Safari. Before troubleshooting, try updating it to the latest version: 6.0. You can do this by clicking the Apple logo in the top left, then clicking Software update.
You can also update to the latest version of OS X, 10.8 Mountain Lion, from the Mac App Store for $19.99, which will automatically install Safari 6 as well, but this isn't essential, only reccomended.
Thanks, let me know if the update helps,
Nathan -
HT4623 i now just have the apple logo on my screen after trying update
i now just have the apple logo on my screen after trying update and itunes cannot connect to my phone.
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/HT1808 -
My iPod itouch when plugged into computer just flashes the apple logo otherwise it just won't start. Try to reset -nothing.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I downloaded the update, but when it was restoring, it was unable to do so and my phone is now stuck at the Apple Logo.
It used to show the iTunes and USB but now it's just the Apple Logo, and no matter what I do, it won't show the device on my iTunes. What is wrong with it and what should I do?Try Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
But... if the Device has been Modified... this will Not necessarily work. -
My iPod touch 5th Gen. wont start up past the apple logo,ive tried holding the power button and the home button,and it wont start up. What do I do?!?!
Try the remaining items of:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
My nano blinks the apple logo when plugged into a charger and will not respond to any reset commands, anyone have experiance with this problem?
By a reset, I assume you meaning pressing and holding both the Select (Center) and Menu buttons (or Volume Down and Sleep/Wake buttons on the 6G Nano) long enough for the Apple logo to appear?
What happens if you try to manually place the iPod into Disk Mode? If you can do that, I would recommend connecting the iPod to iTunes and restoring it.
Putting iPod into Disk Mode
B-rock -
My Iphone doesnt turn on after updating. It keeps on blinking the apple logo, after seeing the low battery image, i tried to charge the iphone. After charging for 30 minutes, it still wont turn on but keeps on blinking the apple logo. It has been blinking for 2 days. Then I tried to connect to itunes, but itunes cant recognize the device. What should I do?
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps..
But... if the Device has been Modified... this will Not necessarily work.
Unauthorized modification of iOS > http://support.apple.com/kb/HT3743 -
My ipod nano 6th gen doesn't start. When I plug it, only blink the apple logo on the screen. I try to reset it holding by 8 seconds start button and volume down and doesn't work. My Ipod doesn't have any shock or water damage. How can I do?
Hey rulosrojos,
The article linked below details a number of troubleshooting steps that can help restore functionality to your iPod nano.
iPod nano (6th generation): Hardware troubleshooting
https://support.apple.com/en-us/TS3474
Sincerely,
Allen
Maybe you are looking for
-
Flexconnect AP with auto anchor at head office
hi All, I have a head quarters with two WLC5508 anchored to another 5508 on the DMZ. Now we want to roll out wireless guest to the branches with local switching of guest wireless traffic. The guest ssid used at head quarters is anchored to the gues
-
How to additional siebel service after configuration is being done.
Hi everyone, We've configured siebel with callcenter service only, the installation went successful. Now if we want to add another service for example "ecommunication" what shall i do. Any help is appreciable. Regards Samad Ul Haq
-
Dreamweaver CS6 - Guidelines in code view
Hello, Is there any extension/plugin that allows to make similar view like in Notepad++? Example: http://screenshu.com/static/uploads/temporary/ed/aq/w0/xtgy6g.jpg I mean those vertical guidelines + selecting closing tag that selects also opening tag
-
Just wondering about the new CC 2014.2 October Update Splash Screens
I was just fascinated about Behance's appearance on Adobe Creative Cloud 2014 splash screens (though surely beacause it was under Adobe) but the new ones are slightly better. Can someone please tell me who made the images used for the splash screens
-
Divide a string at the end of a column
Hello, I have a JTable with two columns and some rows. In the second column there are always strings displayed which does not fit the column size. Is it possible that the string will be automatically divided when the end of the column is reached, the