I upgraded to Mavericks and now I get a LOT of the spinning colored disk when loading a program or almost anything.
I upgraded to Mavericks and now I get a LOT of the spinning colored disk when loading a program or almost anything?
For memory check out OWC http://eshop.macsales.com/, Crucial: http://www.crucial.com/ and Kingston http://www.kingston.com/us/. You will need to know your Mac the year and season your Mac was first sold and model number which can be found here:
> About This Mac > More Info… > System Report > Model Identifier:
Similar Messages
-
I just upgraded to Mavericks and now my Intel iMac is running more slowly. There have been no other changes. What's up with this???
This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve your problem.
If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
Below are instructions to run a UNIX shell script, a type of program. All it does is to gather information about the state of your computer. That information goes nowhere unless you choose to share it on this page. However, you should be cautious about running a program at the instance of a stranger on a public message board. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them.
Here's a summary of what you need to do: Copy a line of text from this web page into the window of another application. Wait about a minute. Then paste some other text, which will have been copied automatically, back into a reply on this page. The sequence is: copy, paste, wait, paste again. Details follow.
You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in your browser, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
clear; Fb='%s\n\t(%s)\n'; Fm='\n%s:\n\n%s\n'; Fs='\n%s: %s\n'; Fu='user %s%%, system %s%%'; PB="/usr/libexec/PlistBuddy -c Print"; A () { [[ a -eq 0 ]]; }; R () { o=; [[ r -eq 0 ]]; }; Pm () { [[ "$o" ]] && o=`sed 's/^ */ /' <<< "$o"` && printf "$Fm" "$1" "$o"; }; Pc () { o=`egrep -v '^[[:blank:]]*($|#)' "$2"`; Pm "$1"; }; Pp () { o=`$PB "$2" | awk -F'= ' \/$3'/{print $2}'`; Pm "$1"; }; Ps () { o="${o##+( )}"; [[ ! "$o" =~ ^0?$ ]] && printf "$Fs" "$1" "$o"; }; id | grep -qw '80(admin)'; a=$?; A && sudo true; r=$?; t=`date +%s`; clear; { A || echo $'No admin access\n'; A && ! R && echo $'No root access\n'; system_profiler SPSoftwareDataType | sed '8!d;s/^ *//'; o=`system_profiler SPHardwareDataType | awk '/Mem/{print $2}'`; o=$((o<4?o:0)); Ps "Memory (GB)"; o=`system_profiler SPDiagnosticsDataType | sed '5,6!d'`; [[ "$o" =~ Pass ]] || Pm "POST"; o=`pmset -g therm | sed 's/^.*CP/CP/'`; egrep -q 'No th|pms' <<< "$o" && o=; Pm "Thermal conditions"; o=`pmset -g sysload | grep -v :`; grep -q '= [^GO]' <<< "$o" || o=; Pm "System load advisory"; o=`nvram boot-args | awk '{$1=""; print}'`; Ps "boot-args"; d=(/ ""); D=(System User); for i in 0 1; do o=`cd ${d[$i]}L*/L*/Dia* && ls | grep -v 'ag$' | tail | awk -F_ '{$NF=a[split($NF,a,".")]; print}'`; Pm "${D[$i]} diagnostics"; done; o=`syslog -F bsd -k Sender kernel -k Message CReq 'GPU |hfs: Ru|I/O e|n Cause: -|NVDA\(|pagin|SATA W|ssert|timed? ?o' | tail -n25 | awk '/:/{$4=""; $5=""; print}'`; Pm "Kernel messages"; o=`df -m / | awk 'NR==2 {print $4}'`; o=$((o<5120?o:0)); Ps "Free space (MiB)"; o=$(($(vm_stat | awk '/eo/{sub("\\.",""); print $2}')/256)); o=$((o>=1024?o:0)); Ps "Pageouts (MiB)"; s=( `sar -u 1 10 | sed '$!d'` ); [[ s[4] -lt 85 ]] && o=`printf "$Fu" ${s[1]} ${s[3]}` || o=; Ps "Total CPU usage" && { s=(`ps acrx -o comm,ruid,%cpu | sed '2!d'`); o=${s[2]}%; Ps "CPU usage by process \"$s\" with UID ${s[1]}"; }; s=(`top -R -l1 -n1 -o prt -stats command,uid,prt | sed '$!d'`); s[2]=${s[2]%[+-]}; o=$((s[2]>=25000?s[2]:0)); Ps "Mach ports used by process \"$s\" with UID ${s[1]}"; o=`kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1`; Pm "Loaded extrinsic kernel extensions"; R && o=`sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|post[fg]|x)/{print $3}'`; Pm "Extrinsic system jobs"; o=`launchctl list | sed 1d | awk '!/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'`; Pm "Extrinsic agents"; o=`find -L {/,}L*/Lau* -type f -exec sh -c 'file -b "$1" | grep -qw XML' {} {} \; -print | while read f; do ID=$($PB\ :Label "$f") || ID="No job label"; printf "$Fb" "$f" "$ID"; done`; Pm "launchd items"; o=`find -L /{S*/,}L*/Star* -type f -exec sh -c 'file -b "$1" | egrep -q "XML|bin|exec"' {} {} \; -print`; Pm "StartupItems"; o=`find -L /S*/L*/E* {/,}L*/{A*d,Compon,Ex,In,Keyb,Mail,P*P,Qu,Scripti,Servi,Spo}* -type d -name Contents -prune | while read d; do ID=$($PB\ :CFBundleIdentifier "$d/Info.plist") || ID="No bundle ID"; egrep -qv "^com\.apple\.[^x]|Accusys|ArcMSR|ATTO|HDPro|HighPoint|driver\.stex|hp-fax|\.hpio|JMicron|microsoft\.MDI|print|SoftRAID" <<< $ID && printf "$Fb" "${d%/Contents}" "$ID"; done`; Pm "Extrinsic loadable bundles"; o=`find -L /u*/{,*/}lib -type f -exec sh -c 'file -b "$1" | grep -qw shared && ! codesign -v "$1"' {} {} \; -print`; Pm "Unsigned shared libraries"; o=`launchctl getenv DYLD_INSERT_LIBRARIES`; Pm "Inserted libraries"; o=`find -L {,/u*/lo*}/e*/periodic -type f -mtime -10d`; Pm "Modified periodic scripts"; o=`scutil --proxy | grep Prox`; Pm "Proxies"; o=`scutil --dns | awk '/r\[0\] /{if ($NF !~ /^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./) print $NF; exit}'`; Ps "DNS"; R && o=`sudo profiles -P | grep : | wc -l`; Ps "Profiles"; for f in fstab sysctl.conf crontab launchd.conf; do Pc $f /etc/$f; done; Pc "hosts" <(grep -v 'host *$' /etc/hosts); Pc "User launchd" ~/.launchd; R && Pc "Root crontab" <(sudo crontab -l); Pc "User crontab" <(crontab -l); R && o=`sudo defaults read com.apple.loginwindow LoginHook`; Pm "Login hook"; Pp "Global login items" /L*/P*/loginw* Path; Pp "User login items" L*/P*/*loginit* Name; Pp "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed 's/\..*$//;s/-[1-9]$//'; o=`find ~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \) | wc -l`; Ps "Restricted user files"; cd; o=`system_profiler SPFontsDataType | egrep "Valid: N|Duplicate: Y" | wc -l`; Ps "Font problems"; o=`find L*/{Con,Pref}* -type f ! -size 0 -name *.plist ! -exec sh -c 'plutil -s "$1" >&-' {} {} \; -print`; Pm "Bad plists"; d=(Desktop L*/Keyc*); n=(20 7); for i in 0 1; do o=`find "${d[$i]}" -type f -maxdepth 1 | wc -l`; o=$((o<=n[$i]?0:o)); Ps "${d[$i]##*/} files"; done; o=$((`date +%s`-t)); Ps "Elapsed time (s)"; } 2>/dev/null | pbcopy; exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign ($) or a percent sign (%). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Click anywhere in the Terminal window and paste (command-V). The text you pasted should vanish immediately. If it doesn't, press the return key.
If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important.
If you're not logged in as an administrator, you won't be prompted for your password. The test will still run. It just won't do anything that requires administrator rights.
The test may take up to a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. There wiil be nothing in the Terminal window and no indication of progress until it's done. Wait for the line "[Process completed]" to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report your results. No harm will be done.
When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
When you post the results, you might see the message, "You have included content in your post that is not permitted." That's because the forum software falsely identifies something in the post as a violation of the terms of use. If that happens, please post the results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Terms of Use of Apple Support Communities ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
I have just upgraded to Maverick and now I cannot find certain JPG 's . These files do exist however I can find them manually . I rely on the search facility and this is slowing me down, I am having to trawl through stuff to find the file I want , before I would put in part of the title and the machine would find it.
In addition to what Allen says, you may find these search tools helpful:
http://apps.tempel.org/FindAnyFile/
http://www.devontechnologies.com/products/freeware/ - EasyFind
http://www.osxbytes.com/ - iFileX (note the MacUpdate link provided on osxbytes page has a Malware advertisement forMacKeeper, do not download).
Note: you posted to the Classic operating system forum. That refers to Mac operating systems from 2005 and earlier in Classic mode, and Mac operating systems as boot systems on certain 2003 and earlier Macs. Mavericks forum questions normally get answered here:
OS X Mavericks -
I upgraded to Maverick and now Time Machine will not connect to the external hard drive to back up files. The external hard drive is a Western Digital "My Book Live" 2 TB. How do I solve problem?
I also had problem accessing my WD MyBookLive after upgrading to Maverick.
To resolve the problem, I used Connect To Server (Cmd K) to specify the IP address.
Then I enter a user id and password I created in the MyBookLive.
You can also verify that you have admin access to the MyBookLive using Safari or Chrome.
Just enter the MyBookLive IP address as the URL. -
I recently upgraded to Mavericks and now don't have access to iphoto. I cannot find my iphoto library to back the photos up before upgrading the iphoto but see the photos when I try to change screensaver? Where are my photos so I can back them up?
The iPhoto library should be in your user folder/Pictures unless it was moved.
-
I have recently upgraded to mavericks and I cannot get my scanner to work. I tried deleting the printer and reinstalled it but no luck
Canon does not support the MP530 on Mavericks, they have not produced drivers and apparently do not intend to,
-
I've upgraded my pc and now Im getting an error message when Im trying to sync my ipod saying I have two itunes libraries. The library thats there is only showing some songs and it's not uploading songs Ive just bought.
You seem to have tried everything, and you say it's syncing fine on your Dad's iMac, so I assume, you have also done a Disk Diagnostic from an earlier post by tt2 and conclude that your iPod Hardisk is good.
You don't have to use it as a heavy paperweight, the problem is only using your Windows 7 machine for syncing.
In your troubleshooting steps, did you try to use another High-Speed USB 2.0 port, USB controller resource are very scarce, so if you use other USB devices, while syncing your iPod, it may just freeze.
Windows have a bad reputation for device conflict, so better don't connect other USB devices, while syncing, better sync it while disconnected from Internet, stop antivirus just before you go to bed.
Have a nice day! -
I just upgraded to Mavericks and can't get my opening page to stay on GOOGLE. IT keeps opening in SITES and then I have to click on GOOGLE to begin searching. I would rather not hav to go through 2 steps to start everytime. I entered google's address in preferences but it ignores my preference.
You don't say which browser you are using so I will assume it's Safari. If so then open Safari - Preferences - General tab and look for where you set the home page, just set it to www.Google.com
If this fails for some reason then open Safari and reset it (look in the Safari menu) and choose all options for the reset. The re-try setting the preference. Post back with your results. -
Upgraded to mavericks and now both email accounts have been merged into one
just upgraded to mavericks and now both mine and my husbands email accounts have been merged together rather than having separate inbox's. How do I separate them again?
Great question, I have a similar problem except that the photo library appears to take precidence over my organised folders so not all of my folders appear on my IP 5.
I eagerly await a solution, -
Upgraded to maverick and now can't open excel projects
I recently upgraded to maverick and now can't go back to open excel spreadsheets I need for my business. I've even changed the permissions and I can only preview, not modify. Any suggestions?
Was just having this issue with my wife's computer after upgrading to Mavericks. Maybe a long shot, but if your filenames have forward slashes in them (such as for dates), change them to backslashes. No idea why but it works. I seem to recall having the same problem with Excel some time in the past and this was the solution then too.
-
I upgraded to Mavericks and now some of my utilities --- such as disk utility and system information no longer work. I find Disk Utility useful and would like to have it. Doesn't Makericks include
Boot into your recovery partition (restart, hold down ⌘R until you see the Apple logo), and use Disk Utility to repair your hard drive. Repair permissions too while you're there. OS X: About OS X Recovery
If that doesn't work, I'd reinstall Mavericks over your current installation. -
I upgraded to Mavericks and now in pages and numbers my files text cannot be seen
I upgraded to Mavericks and now in pages and numbers my files text cannot be seen unless you highlight it. I am using iWork 08. and running 10.9.4
These are the versions of iPhoto that are and are not compatible with Mavericks:
What version of iPhoto are you running? What happens when you try to launch iPhoto? Any message?
OT -
Hy i Upgrade my iPhone and now my mp4 Data are in the file Video and i can't make any Playlist with them! Any idea?
I'm having the same issue, i restored my phone to Factory settings, even tried restoring it to my backup, half of my music bought from itunes won't play on my iphone and i'm super annoyed, this only happened once i updated to ios 7.2 so i assume its another glitch to go with my imessages not sending, getting sick of this.
-
I just updated my iTunes and now I get a message that the application has failed to start because MSVCR80.dll was not found. What happened and how do I fix this? I can't access any of my music now.
Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99460) -
I downloaded Mac OS. Mavericks and now my laptop won't intall the program it's says disk error and I already open te utility and repaid the disk and still stuck on that intall screen wat can I do
Why did you wipe the drive?
Were you having problems?
If you were those problem may be related to a failing hard drive and that is why the TM backup could be restored.
In you topic header you say the system won't boot from the SL DVD, But it di for you to wipe the drive. Then it should again boot from the SL DVD.
Insert the DVD and reboot, hold down the Option key and select the Optical drive, SL DVD, as the Boot source.
Maybe you are looking for
-
How do you become edge customer?
For some odd reason maybe it has to do with credit but I am not allowed to have edge (for know at least) how do I join the edge club?
-
Java HelloWorldApp: Error java.lang.NoClassDefFoundError
Hi, Kindly anyone help me when i am trying to execute in $ prompt:java HelloWorldApp Exception in thread "main" java.lang.NoClassDefFoundError: HelloWorldApp Caused by: java.lang.ClassNotFoundException: HelloWorldApp at java.net.URLClassLoader$1.run(
-
Get thrown out of ebay account constantly
Probably a rather profane problem: When I log into my ebay account with Safari and browse on the ebay pages I keep getting thrown out - meaning: I need to re-log in every other minute. Deleting my preferences hasn't helped. Also Safari does not autom
-
Hi; we made a repair coding in MFBF. we send a mail to someone after saving proggress. in debug mode it's working. but in normal mode it's not working. WHY?. Thanks
-
Hi ! I'm using here a powerline network with Netgear solutions, everything works fine but streaming video from a distant hard drive to my macmini (TV connected) shows some buffer errors. I'm not sure the problem comes from the powerline network as I'