I've tried safe mode but I dont understand what is happening. I tried pressing the power button on and off for several times and nothing happens, I'm always stuck on an apple logo and a spinning wheel. I dont know how to get to the Partition and the DiskU

I've tried safe mode but I dont understand what is happening. I tried pressing the power button on and off for several times and nothing happens, I'm always stuck on an apple logo and a spinning wheel. I dont know how to get to the Partition and the DiskUtility. The Apple Logo and the Progress Indicator will continue to spin and I have literally no idea what to do. i am in desperate need of help. help me pls

Turn it off.
Start it up again and (at the sound of the chime) press and hold the command and the R keys, hold them down until Recovery loads. When it does you will select Disk Utility and you should be on the First Aid tab when it opens, if you are not please select it. Then select the partition (in the side bar, 2nd entry on the list, see picture).
Yours is probably called Macintosh HD.
Once you have selected it go to the lower righthand corner of the First Aid dialog and press Repair Disk.
This will take 10 minutes approximately. Post back when it is finished and tell me what it says.

Similar Messages

  • I've tried safe mode but I dont understand what is happening. I tried pressing the power button on and off for several times and nothing happens, I'm always stuck on an apple logo and a spinning wheel. I dont know how to get to the Partition

    I've tried safe mode but I dont understand what is happening. I tried pressing the power button on and off for several times and nothing happens, I'm always stuck on an apple logo and a spinning wheel. I dont know how to get to the Partition and the DiskUtility. The Apple Logo and the Progress Indicator will continue to spin and I have literally no idea what to do. i am in desperate need of help. help me pls

    Reboot hold the command R for recovery.

  • HT1222 My phone is telling me about a Software Update but for the first time it is asking me for a passcode, I have never set up a passcode and do not know how to get around this to do the upgrade?

    My phone is telling me about a Software Update 7.1.1 but for the first time it is asking me for a passcode, I have never set up a passcode and do not know how to get around this to do the upgrade?

    See if this helps:
    iOS: Forgotten passcode or device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212

  • My dad has itunes on his PC. I don't have my own but I recently have an iPad mini and an iPod. I don't know how to get songs onto itunes on the PC, using a different account or at least private/ separate..

    My dad has itunes on his PC. I don't have my own but I recently have an iPad mini and an iPod. I don't know how to get songs onto itunes on the PC, using a different account or at least private/ separate..
    So how do I create a separate I tunes on a PC which already has itunes... Or if not can I plug my iPad to the PC and use itunes on my iPad, and drag mp3s from a computer.
    I'm not sure what the equivalent of a desktop is on the iPad.. And I don't actually know how to use the icloud either...
    Can anyone start me off, given it have a iPad and use of a PC - not mine with existing iplayer
    I do have spotify soundcloud so I could potentially use these.. If there is a route of getting either mp3's etc to end up on my iPad or iPod.
    Kind Regards

    iTunes 11
    If you  have iTunes 11 turn on the Sidebar.  Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar. The sidebar is where Devices appears. and Control+B to show the Menu bar
    To import music into your iTunes library on the computer go to iTunes>Help>iTunes Help>Add items to iTunes and follow the instructions
    To sync to your iPod go to iTunes>Help>iTunes Help>Sync your iPod....>Sync You Device and follow the instructions.

  • I've got OSX/Genieo.A virus on my mac and don't know how to get rid of it and why I have it

    I've got OSX/Genieo.A virus on my mac and don't know how to get rid of it and w I have it

    There is no need to download anything to solve this problem.
    You installed the "Genieo" malware. The product is a fraud, and the developer knowingly distributes an uninstaller that doesn't work. I suggest the procedure below to disable Genieo. This procedure may leave a few small files behind, but it will permanently deactivate the malware (as long as you never reinstall it.)
    Malware is always changing to get around the defenses against it. These instructions are valid as of now, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for more recent discussions or start a new one.
    Back up all data before proceeding.
    Step 1
    Triple-click anywhere in the line below on this page to select it:
    /Library/Frameworks/GenieoExtra.framework
    Right-click or control-click the line and select
              Services ▹ Reveal in Finder (or just Reveal)
    from the contextual menu.
    If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
              Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
    A folder should open with an item named "GenieoExtra.framework" selected. Move that item to the Trash. You'll be prompted for your administrator password.
    Move each of these items to the Trash in the same way:
    /Applications/Genieo.app
    /Applications/Reset Search.app
    /Applications/Uninstall Genieo.app
    /Library/LaunchAgents/com.genieo.completer.update.plist
    /Library/LaunchAgents/com.genieo.engine.plist
    /Library/LaunchAgents/com.genieoinnovation.macextension.plist
    /Library/LaunchDaemons/com.genieoinnovation.macextension.client.plist
    /Library/PrivilegedHelperTools/com.genieoinnovation.macextension.client
    /usr/lib/libgenkit.dylib
    /usr/lib/libgenkitsa.dylib
    /usr/lib/libimckit.dylib
    /usr/lib/libimckitsa.dylib
    ~/Library/Application Support/com.genieoinnovation.Installer
    ~/Library/LaunchAgents/com.genieo.completer.download.plist
    ~/Library/LaunchAgents/com.genieo.completer.update.plist
    If there are other items with a name that includes "Genieo" or "genieo" alongside any of those listed above, move them as well. Some of these items will be absent, in which case you'll get a message that the file can't be found. Skip that item and go on to the next one.
    Restart and empty the Trash. Don't try to empty the Trash until you have restarted.
    Step 2
    From the Safari menu bar, select
              Safari ▹ Preferences... ▹ Extensions
    Uninstall any extensions you don't know you need, including ones called "Genieo" or "Omnibar," and any that have the word "Spigot" or "InstallMac" in the description. If in doubt, uninstall all extensions. Do the equivalent for the Firefox and Chrome browsers, if you use either of those.
    Your web browser(s) should now be working, and you should be able to reset the home page and search engine. If not, stop here and post your results.
    Make sure you don't repeat the mistake that led you to install this trojan. Chances are you got it from an Internet cesspit such as "Softonic" or "CNET Download." Never visit either of those sites again. You might also have downloaded it from an ad in a page on some other site. The ad has a large green button labeled "Download" or "Download Now" in white letters. The button is designed to confuse people who intend to download something else on the same page. If youever download a file that isn't obviously what you expected, delete it immediately.
    You may be wondering why you didn't get a warning from Gatekeeper about installing software from an unknown developer, as you should have. The reason is that this Internet criminal has a codesigning certificate issued by Apple, which causes Gatekeeper to give the installer a pass. Apple could revoke the certificate, but as of this writing, has not done so, even though it's aware of the problem. This failure of oversight has compromised both Gatekeeper and the Developer ID program. You can't rely on Gatekeeper alone to protect you from harmful software.
    Finally, be forewarned that when Genieo is mentioned on this site, the attacker sometimes shows up under the name "Genieo support." He will tell you to run a fake "uninstaller." As he intends, the uninstaller does not completely remove the malware, and is in fact malware itself.

  • Eth0 is being up and down for several time during boot

    My wicd doesn't connect to eth0 on the first attempt after boot up. It is configured to eth0 always have a higher priority to connect.
    My dmesg shows that eth0 being up and down for several time during boot. I have e1000e in my MODULES list.
    Here is my rc.conf
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
    # startup and during the boot process. If set to 'no', the C locale is used.
    # HARDWARECLOCK: set to "", "UTC" or "localtime", any other value will result
    # in the hardware clock being left untouched (useful for virtualization)
    # Note: Using "localtime" is discouraged, using "" makes hwclock fall back
    # to the value in /var/lib/hwclock/adjfile
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # Note: if unset, the value in /etc/localtime is used unchanged
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="en_US.UTF-8"
    DAEMON_LOCALE="no"
    HARDWARECLOCK=""
    TIMEZONE="Asia/Hong_Kong"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
    # Replace every !module by an entry as on the following line in a file in
    # /etc/modprobe.d:
    # blacklist module
    # See "man modprobe.conf" for details.
    MOD_AUTOLOAD="yes"
    MODULES=(acpi-cpufreq fuse tp_smapi vboxdrv e1000e)
    # Udev settle timeout (default to 30)
    UDEV_TIMEOUT=30
    # Scan for FakeRAID (dmraid) Volumes at startup
    USEDMRAID="no"
    # Scan for BTRFS volumes at startup
    USEBTRFS="no"
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    # HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
    HOSTNAME="antony-tp"
    # Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
    # Wired network setup
    # - interface: name of device (required)
    # - address: IP address (leave blank for DHCP)
    # - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
    # - broadcast: broadcast address (ignored for DHCP) (optional)
    # - gateway: default route (ignored for DHCP)
    # Static IP example
    # interface=eth0
    # address=192.168.0.2
    # netmask=255.255.255.0
    # broadcast=192.168.0.255
    # gateway=192.168.0.1
    # DHCP example
    # interface=eth0
    # address=
    # netmask=
    # gateway=
    # Setting this to "yes" will skip network shutdown.
    # This is required if your root device is on NFS.
    NETWORK_PERSIST="yes"
    # Enable these netcfg profiles at boot-up. These are useful if you happen to
    # need more advanced network features than the simple network service
    # supports, such as multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This requires the netcfg package
    #NETWORKS=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    # If something other takes care of your hardware clock (ntpd, dual-boot...)
    # you should disable 'hwclock' here.
    DAEMONS=(!hwclock syslog-ng dbus !network !dhcpcd rpcbind acpid @wicd nfs-common netfs @crond cups @laptop-mode @alsa @sensors ntpd @slim bluetooth)
    Here is a segment of my dmesg
    [ 2.759302] e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
    [ 2.759304] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
    [ 2.759338] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [ 2.759348] e1000e 0000:00:19.0: setting latency timer to 64
    [ 2.759467] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 2.766107] tpm_tis 00:0a: 1.2 TPM (device-id 0x0, rev-id 78)
    [ 2.766808] ACPI: AC Adapter [AC] (on-line)
    [ 2.776492] wmi: Mapper loaded
    [ 2.777212] mei: module is from the staging directory, the quality is unknown, you have been warned.
    [ 2.777781] thermal LNXTHERM:00: registered as thermal_zone0
    [ 2.777783] ACPI: Thermal Zone [THM0] (66 C)
    [ 2.778291] iTCO_vendor_support: vendor-support=0
    [ 2.780137] ACPI: Battery Slot [BAT0] (battery present)
    [ 2.780958] input: PC Speaker as /devices/platform/pcspkr/input/input4
    [ 2.781462] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
    [ 2.781547] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
    [ 2.781919] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 2.783139] cfg80211: Calling CRDA to update world regulatory domain
    [ 2.789182] [drm] Initialized drm 1.1.0 20060810
    [ 2.789538] hub 4-1:1.0: USB hub found
    [ 2.789616] hub 4-1:1.0: 8 ports detected
    [ 2.792925] Non-volatile memory driver v1.3
    [ 2.795877] thinkpad_acpi: ThinkPad ACPI Extras v0.24
    [ 2.795879] thinkpad_acpi: http://ibm-acpi.sf.net/
    [ 2.795881] thinkpad_acpi: ThinkPad BIOS 8DET54WW (1.24 ), EC unknown
    [ 2.795882] thinkpad_acpi: Lenovo ThinkPad X220, model 4290NL5
    [ 2.797236] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
    [ 2.797352] thinkpad_acpi: radio switch found; radios are enabled
    [ 2.797466] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
    [ 2.799752] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
    [ 2.800067] Registered led device: tpacpi::thinklight
    [ 2.800091] Registered led device: tpacpi::power
    [ 2.800106] Registered led device: tpacpi::standby
    [ 2.800120] Registered led device: tpacpi::thinkvantage
    [ 2.800192] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
    [ 2.800254] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
    [ 2.801077] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input5
    [ 2.801162] sdhci: Secure Digital Host Controller Interface driver
    [ 2.801164] sdhci: Copyright(c) Pierre Ossman
    [ 2.801707] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
    [ 2.801709] Copyright(c) 2003-2011 Intel Corporation
    [ 2.801744] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 2.801753] iwlwifi 0000:03:00.0: setting latency timer to 64
    [ 2.801789] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000
    [ 2.801791] iwlwifi 0000:03:00.0: pci_resource_base = ffffc90005abc000
    [ 2.801793] iwlwifi 0000:03:00.0: HW Revision ID = 0x34
    [ 2.801877] iwlwifi 0000:03:00.0: irq 49 for MSI/MSI-X
    [ 2.801913] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
    [ 2.801962] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
    [ 2.802045] sdhci-pci 0000:0d:00.0: SDHCI controller found [1180:e822] (rev 7)
    [ 2.802067] sdhci-pci 0000:0d:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 2.802107] sdhci-pci 0000:0d:00.0: setting latency timer to 64
    [ 2.802118] _regulator_get: 0000:0d:00.0 supply vmmc not found, using dummy regulator
    [ 2.802188] Registered led device: mmc0::
    [ 2.803329] mmc0: SDHCI controller on PCI [0000:0d:00.0] using DMA
    [ 2.815226] iwlwifi 0000:03:00.0: device EEPROM VER=0x715, CALIB=0x6
    [ 2.815229] iwlwifi 0000:03:00.0: Device SKU: 0X1f0
    [ 2.815231] iwlwifi 0000:03:00.0: Valid Tx ant: 0X3, Valid Rx ant: 0X3
    [ 2.815247] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
    [ 2.845674] iwlwifi 0000:03:00.0: loaded firmware version 17.168.5.3 build 42301
    [ 2.845820] Registered led device: phy0-led
    [ 2.850630] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
    [ 2.862431] usb 1-1.2: new low-speed USB device number 3 using ehci_hcd
    [ 2.943648] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) f0:de:f1:92:77:26
    [ 2.943651] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
    [ 2.943712] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 1000FF-0FF
    [ 2.943734] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 2.943739] mei 0000:00:16.0: setting latency timer to 64
    [ 2.943817] mei 0000:00:16.0: irq 50 for MSI/MSI-X
    [ 2.944502] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
    [ 2.945021] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
    [ 2.946341] watchdog: INTCAMT: cannot register miscdev on minor=130 (err=-16).
    [ 2.946452] watchdog: error registering /dev/watchdog (err=-16).
    [ 2.946523] mei: unable to register watchdog device.
    [ 2.946598] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
    [ 2.946692] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
    [ 2.946734] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    [ 2.948359] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    [ 2.948422] snd_hda_intel 0000:00:1b.0: irq 51 for MSI/MSI-X
    [ 2.948444] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
    [ 3.022245] usb 1-1.3: new full-speed USB device number 4 using ehci_hcd
    [ 3.172080] usb 1-1.4: new full-speed USB device number 5 using ehci_hcd
    [ 3.274597] Bluetooth: Core ver 2.16
    [ 3.274611] NET: Registered protocol family 31
    [ 3.274612] Bluetooth: HCI device and connection manager initialized
    [ 3.274614] Bluetooth: HCI socket layer initialized
    [ 3.274614] Bluetooth: L2CAP socket layer initialized
    [ 3.274618] Bluetooth: SCO socket layer initialized
    [ 3.275535] Bluetooth: Generic Bluetooth USB driver ver 0.6
    [ 3.276006] usbcore: registered new interface driver btusb
    [ 3.338454] usb 1-1.6: new high-speed USB device number 6 using ehci_hcd
    [ 3.444567] Linux media interface: v0.10
    [ 3.447387] Linux video capture interface: v2.00
    [ 3.448573] input: Logitech Trackball as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input6
    [ 3.448671] generic-usb 0003:046D:C404.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Trackball] on usb-0000:00:1a.0-1.2/input0
    [ 3.448690] usbcore: registered new interface driver usbhid
    [ 3.448691] usbhid: USB HID core driver
    [ 3.449136] uvcvideo: Found UVC 1.00 device Integrated Camera (04f2:b217)
    [ 3.450945] input: Integrated Camera as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input7
    [ 3.450987] usbcore: registered new interface driver uvcvideo
    [ 3.450988] USB Video Class driver (1.1.1)
    [ 3.484049] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
    [ 3.491137] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
    [ 3.491298] HDMI status: Codec=3 Pin=6 Presence_Detect=0 ELD_Valid=0
    [ 3.491486] HDMI status: Codec=3 Pin=7 Presence_Detect=0 ELD_Valid=0
    [ 3.491637] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
    [ 3.491709] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
    [ 3.491765] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
    [ 3.492050] i915 0000:00:02.0: power state changed by ACPI to D0
    [ 3.492053] i915 0000:00:02.0: power state changed by ACPI to D0
    [ 3.492059] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 3.492062] i915 0000:00:02.0: setting latency timer to 64
    [ 3.538056] mtrr: no more MTRRs available
    [ 3.538058] [drm] MTRR allocation failed. Graphics performance may suffer.
    [ 3.538266] i915 0000:00:02.0: irq 52 for MSI/MSI-X
    [ 3.538270] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 3.538271] [drm] Driver supports precise vblank timestamp query.
    [ 3.538292] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 3.664501] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x120c00
    [ 3.664518] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
    [ 3.716317] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12
    [ 4.407165] fbcon: inteldrmfb (fb0) is primary device
    [ 4.575259] Console: switching to colour frame buffer device 170x48
    [ 4.577042] fb0: inteldrmfb frame buffer device
    [ 4.577043] drm: registered panic notifier
    [ 4.607860] acpi device:01: registered as cooling_device4
    [ 4.607985] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input13
    [ 4.608039] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    [ 4.608122] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 4.757243] EXT4-fs (sda3): re-mounted. Opts: discard
    [ 4.765917] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: discard
    [ 4.776777] Adding 262140k swap on /dev/sda2. Priority:-1 extents:1 across:262140k SS
    [ 5.099467] NET: Registered protocol family 10
    [ 6.048650] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 6.098038] Bluetooth: RFCOMM TTY layer initialized
    [ 6.098055] Bluetooth: RFCOMM socket layer initialized
    [ 6.098057] Bluetooth: RFCOMM ver 1.11
    [ 6.278766] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
    [ 6.278893] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
    [ 6.568639] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
    [ 6.568775] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
    [ 6.684082] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 7.176563] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 7.226662] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 7.227110] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 10.229345] IBM TrackPoint firmware: 0x0e, buttons: 3/3
    [ 10.490618] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input14
    [ 10.817814] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
    [ 10.819315] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 11.186166] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S
    [ 11.186292] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
    [ 11.313367] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 11.665342] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 11.717591] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 11.718042] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 11.964795] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 12.017213] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
    [ 12.017720] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 13.811264] EXT4-fs (sda3): re-mounted. Opts: discard,commit=0
    [ 13.826031] EXT4-fs (sda4): re-mounted. Opts: discard,commit=0
    [ 15.178905] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
    [ 15.180472] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 25.663056] eth0: no IPv6 routers present
    Any hint for tracing the root of this problem? Thank you very much!

    Hi ...
    If you have moved the Safari application from the Applications folder, move it back.
    As far as the cache goes, there's a work around for that when you can't empty the Safari cache from the menu bar.
    Go to    ~/Library/Caches/com.aple.Safari.Cache.db.  Move the Cache.db file to the Trash.
    Try Safari.
    Mac OS X (10.7.2)   <  from your profile
    If that is corrrect, you need to update your system software. Click your Apple menu icon top left in your screen. From the drop down menu click Software
    Update ...
    ~ (Tilde) character represents the Home folder.
    For Lion v10.7x:  To find the Home folder in OS X Lion, open the Finder, hold the Option key, and choose Go > Library

  • I reset my macbook pro a few days ago.. and when i started to use it again i noticed all my apps were gone (keynote, iMovie, garage band, etc) i don't know how to get them all back and every time i try it tells me i must buy them.. what do i do?

    I reset my macbook pro a few days ago.. and when i started to use it again i noticed all my apps were gone (keynote, iMovie, garage band, etc) i don't know how to get them all back and every time i try it tells me i must buy them.. what do i do?
    should i come into the actual apple store or can you help online ?

    Hi vickkjayy11 and welcome to Apple Support Communities,
    Just to be clear, we are a peer to peer support community and have nothing official to do with Apple.
    So to your problem, when you say:
    "I reset my macbook pro a few days ago"
    What exactly happened? Did you have a Time Machine backup?
    Read this:
    OS X: About OS X Recovery - Apple Support
    It would help to know the exact model (size and year) and which OS you're using.

  • Every time I try to download the new version of Adobe Flash Player it saves as a .txt file and I do not know how to get it to save in the correct format.

    Every time I try to download the new version of Adobe Flash Player it saves as a .txt file and I do not know how to get it to save in the correct format.

    Please post in the Adobe Flash Player forum.

  • MacBook Pro won't boot - tried safe mode but it went to black screen after trying.

    my MacBook Pro froze after the fan was running very loudly. I turned it off and try to reboot but just got a gray screen. I tried to boot in safe mode but that did not work.any other thoughts on what might help?

    Reinstalling OS X Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Reinstalling OS X Without Erasing the Drive
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility and press the Continue button. After Disk Utility loads select the Macintosh HD entry from the the left side list.  Click on the First Aid tab, then click on the Repair Disk button. If Disk Utility reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit Disk Utility and return to the main menu.
    Reinstall OS X: Select Reinstall OS X and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    Alternatively, see:
    Reinstall OS X Without Erasing the Drive
    Choose the version you have installed now:
    OS X Yosemite- Reinstall OS X
    OS X Mavericks- Reinstall OS X
    OS X Mountain Lion- Reinstall OS X
    OS X Lion- Reinstall Mac OS X
         Note: You will need an active Internet connection. I suggest using Ethernet
                     if possible because it is three times faster than wireless.

  • No toolbars. I tried 'safe mode' but still no tool bar to navigate with also reinstalled

    No tool bars/address bar/only "Firefox-Mozilla Firefox" upper left corner and Firefox tabs. That's it. Went to your chat they directed me to reinstall-I did-same thing-tried 'safe mode' no help there either.
    == This happened ==
    Every time Firefox opened
    == after installed, worked OK for a while back in January

    Hit the '''Alt''' key to show the Menu bar, then open View > Toolbars and select Menu bar, so it has a check-mark.

  • I don't think my computer is completely shutting down.  I think it is only going into sleep mode.  When I hit the power button, it turns off immediately instead of shutting down.

    I don't think my Mac Pro is completely shutting down.  When I hit the power button, it just turns off immediately instead of going through the normal shut down procedures.  I heard that I should try resetting the SMC, which involves removing the power cord.  However, when I remove and replace the power cord, it turns on automatically, so I can't even properly reset that to see if it is the issue.  Is this probably a power supply issue?
    Actually, in case this information helps... The computer went into sleep mode the other day, and would not come back.  This is a work computer that I use for our photography business, and at this point I am just trying to run it as a drive to get the photos onto our new computer, but this issue is keeping us from doing so.  Any help would be greatly appreciated!

    Try a SMC reset.
    DALE

  • I have a MacBook Pro 13.3 OS- MAC OS X LION.Whenever I am staring the computer, it says You need to restart your computer by pressing the power button.I did this number of times and everytime it freezes to the same screen.Solution needed urgently pls.

    I have a MacBook Pro 13.3 OS- MAC OS X LION.
    Whenever I am staring the computer, it says You need to restart your computer by pressing the power button.
    I did this number of times and everytime it freezes to the same screen.Solution needed urgently pls.
    Thank you for any help in this regard that comes fast.

    The details of the kernel-panic report is as follows-
    Interval Since Last Panic Report:  1458653 sec
    Panics Since Last Report:          6
    Anonymous UUID:                    70BA6A**************************************************
    Sun Sep 16 23:00:13 2012
    panic(cpu 0 caller 0xffffff80002c4794): Kernel trap at 0xffffff8000290560, type 14=page fault, registers:
    CR0: 0x0000000080010033, CR2: 0x0000000000800028, CR3: 0x000000000a509005, CR4: 0x00000000001606e0
    RAX: 0x0000000000000001, RBX: 0x0000000000820000, RCX: 0xffffff801122dc40, RDX: 0x0000000000020501
    RSP: 0xffffff80ef3d3da0, RBP: 0xffffff80ef3d3dc0, RSI: 0x000000002b1d78b6, RDI: 0xffffff800342d280
    R8:  0xffffff80ef3d3f08, R9:  0xffffff80ef3d3ef8, R10: 0x000000010d901000, R11: 0x0000000000000206
    R12: 0xffffff800342d280, R13: 0x0000000000000000, R14: 0xffffff8011cd6500, R15: 0x0000000000800000
    RFL: 0x0000000000010206, RIP: 0xffffff8000290560, CS:  0x0000000000000008, SS:  0x0000000000000000
    CR2: 0x0000000000800028, Error code: 0x0000000000000000, Faulting CPU: 0x0
    Backtrace (CPU 0), Frame : Return Address
    0xffffff80ef3d3a50 : 0xffffff8000220792
    0xffffff80ef3d3ad0 : 0xffffff80002c4794
    0xffffff80ef3d3c80 : 0xffffff80002da55d
    0xffffff80ef3d3ca0 : 0xffffff8000290560
    0xffffff80ef3d3dc0 : 0xffffff800026c9c3
    0xffffff80ef3d3f40 : 0xffffff80002c3fbb
    0xffffff80ef3d3fb0 : 0xffffff80002da481
    BSD process name corresponding to current thread: fsck_hfs
    Mac OS version:
    11E2620
    Kernel version:
    Darwin Kernel Version 11.4.2: Wed May 30 20:13:51 PDT 2012; root:xnu-1699.31.2~1/RELEASE_X86_64
    Kernel UUID: 25EC645A-8793-3201-8D0A-23EA280EC755
    System model name: MacBookPro9,2 (Mac-6F01561E16C75D06)
    System uptime in nanoseconds: 4850001132
    last loaded kext at 1796984176: com.apple.driver.BroadcomUSBBluetoothHCIController    4.0.7f2 (addr 0xffffff7f80e16000, size 57344)
    loaded kexts:
    com.apple.driver.BroadcomUSBBluetoothHCIController    4.0.7f2
    com.apple.driver.AppleUSBTCButtons    227.6
    com.apple.driver.AppleUSBTCKeyEventDriver    227.6
    com.apple.driver.AppleUSBTCKeyboard    227.6
    com.apple.driver.AppleIRController    312
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless    1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
    com.apple.BootCache    33
    com.apple.iokit.SCSITaskUserClient    3.2.1
    com.apple.driver.XsanFilter    404
    com.apple.iokit.IOAHCISerialATAPI    2.0.3
    com.apple.iokit.IOAHCIBlockStorage    2.0.4
    com.apple.driver.AppleFWOHCI    4.8.9
    com.apple.driver.AirPort.Brcm4331    560.7.21
    com.apple.driver.AppleSDXC    1.2.2
    com.apple.driver.AppleUSBHub    5.0.8
    com.apple.iokit.AppleBCM5701Ethernet    3.2.4b8
    com.apple.driver.AppleEFINVRAM    1.6.1
    com.apple.driver.AppleSmartBatteryManager    161.0.0
    com.apple.driver.AppleAHCIPort    2.3.0
    com.apple.driver.AppleUSBEHCI    5.0.7
    com.apple.driver.AppleUSBXHCI    1.0.7
    com.apple.driver.AppleACPIButtons    1.5
    com.apple.driver.AppleRTC    1.5
    com.apple.driver.AppleHPET    1.7
    com.apple.driver.AppleSMBIOS    1.9
    com.apple.driver.AppleACPIEC    1.5
    com.apple.driver.AppleAPIC    1.6
    com.apple.driver.AppleIntelCPUPowerManagementClient    195.0.0
    com.apple.nke.applicationfirewall    3.2.30
    com.apple.security.quarantine    1.3
    com.apple.security.TMSafetyNet    8
    com.apple.driver.AppleIntelCPUPowerManagement    195.0.0
    com.apple.driver.AppleUSBBluetoothHCIController    4.0.7f2
    com.apple.iokit.IOBluetoothFamily    4.0.7f2
    com.apple.driver.AppleFileSystemDriver    13
    com.apple.driver.AppleUSBMultitouch    230.5
    com.apple.driver.AppleThunderboltDPInAdapter    1.8.4
    com.apple.driver.AppleThunderboltDPAdapterFamily    1.8.4
    com.apple.driver.AppleThunderboltPCIDownAdapter    1.2.5
    com.apple.iokit.IOUSBHIDDriver    5.0.0
    com.apple.driver.AppleUSBMergeNub    5.0.7
    com.apple.driver.AppleUSBComposite    5.0.0
    com.apple.iokit.IOSCSIMultimediaCommandsDevice    3.2.1
    com.apple.iokit.IOBDStorageFamily    1.7
    com.apple.iokit.IODVDStorageFamily    1.7.1
    com.apple.iokit.IOCDStorageFamily    1.7.1
    com.apple.driver.AppleThunderboltNHI    1.6.0
    com.apple.iokit.IOThunderboltFamily    2.0.3
    com.apple.iokit.IOSCSIArchitectureModelFamily    3.2.1
    com.apple.iokit.IOFireWireFamily    4.4.5
    com.apple.iokit.IO80211Family    420.3
    com.apple.iokit.IOEthernetAVBController    1.0.1b1
    com.apple.iokit.IONetworkingFamily    2.1
    com.apple.iokit.IOUSBUserClient    5.0.0
    com.apple.iokit.IOAHCIFamily    2.0.8
    com.apple.iokit.IOUSBFamily    5.0.8
    com.apple.driver.AppleEFIRuntime    1.6.1
    com.apple.iokit.IOHIDFamily    1.7.1
    com.apple.iokit.IOSMBusFamily    1.1
    com.apple.security.sandbox    177.5
    com.apple.kext.AppleMatch    1.0.0d1
    com.apple.driver.DiskImages    331.7
    com.apple.iokit.IOStorageFamily    1.7.2
    com.apple.driver.AppleKeyStore    28.18
    com.apple.driver.AppleACPIPlatform    1.5
    com.apple.iokit.IOPCIFamily    2.7
    com.apple.iokit.IOACPIFamily    1.4

  • I got a message saying my virtual memory was full and need to know how to get rid of some of the info

    1. I was editing an article, and the screen went grey every time i typed in one character. It encouraged me to start again, but the same thing kept happening, until it finally said the virtual memory was filled, and I had to go to "help" to fix the problem. So here I am Help!!! Sahra

    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
    *Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
    *Do NOT click the Reset button on the Safe Mode start window
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
    You can check the memory usage by Firefox on the about:memory page.
    You can open <b>about:</b> pages via the location/address bar like you open a web page.

  • My Apple ID has been disabled. Does anyone know how to get it reinstated

    My Apple ID has been disabled because there were some unauthorized charges to my ITunes account and I filed a clamp with my bank but now I can't update or download anything. I went to the Applenstore by my house and they couldn't help me. Does anyone know how to restore a disabled Apple ID?

    SEe the "more like this" section on the right side of this page. Your question has been asked and answered hundreds of times.

  • My iPhone has a red dot on the voicemail box and I don't even have voicemail activated! Do you know how to get rid of it and make a voicemail?

    There is a red dot on my voicemail app on the phone and it won't go away. I don't even have a voicemail and I don't know how to make one. How can I make one or atleast make the dot go away.

    This sounds more like a Windows question, than a Firefox question. When you say that an image shows up every time you open your computer, do you mean every time you turn on your computer, or every time you start Firefox?

Maybe you are looking for

  • Custom Report Object To Render Vector Image

    Post Author: RSlaughter CA Forum: .NET Hi, I'm using the version of Crystal Reports that ships with Visual Studio .Net 2003 (Maintaining a legacy app) and have come across a problem where I need a way to convert data that is stored as text into a set

  • Why does my firefox 6.0.1 go not responding every time I open a second tab? I need to have more than 1 tabs open for what I'm doing.

    Details: I open browser to go to page. From there I open second page which I've always been able to do and it won't load. It says no responding and sits there forever deciding what to do. Then it will finally say something about stop running script,

  • JTidy in weblogic 10.3 throws AbstractMethodError

    Hi all, Last year a developed a portlet application that makes the transformation of a jTidy-DOM-SDK5 to an string as in the next snippet, this year I'm being asked to migrate that application to weblogic portal 10.3 with SDK6 and I'm getting an erro

  • Help on cdc and pp

    1) i would like to develop application for pocket pc using cdc and personal profile for pda and i still don't how to begin even after reading the documentations that came with cdc and profile.help me please! 2) is there any IDEs and emulators availab

  • Cost Components for W I P

    HI All, What are the cost components for the WIP process. I understand this is been defined in the Overhead key for the Materials in the Production order. I would like to know the Cost components which are added as the factors of production in the WI