I was mid facetime call and my phone turned off and wouldnt turn on until i plugged it in. then the date was wrong,it said no service, and wont let me turn wifi on. also it wont stay on for more than a few minutes at a time

i was mid facetime call and my phone turned off and wouldnt turn on until i plugged it in. then the date was wrong,it said no service, and wont let me turn wifi on. also it wont stay on for more than a few minutes at a time. Help?

Sounds like a hardware failure.
Make an appointment at the genius bar and take it in for them to look at. It will probably need to be replaced.

Similar Messages

HP 3050 will not stay on the wireless network for more than a few minutes at a time.

My HP DeskJet 3050 J610 is constantly dropping the wireless connection. It won't stay on for more than a few minutes. If I power cycle, it comes right back on, but drops again after a few minutes. It will print fine from a USB. When it drops off, pings time out even though the device shows "ready" in Windows 7, Windows XP and OSX. I've done everything HP suggests - static IP, upgraded firmware, diagnostic tools, etc. I am out of options.
I can hit print right now, printer shows as ready, then I will get a print error. If I go over and power cycle the printer, my document will print - most of the time. It will remain on the network for a few minutes, then stop working. As soon as I power cycle it, I get a few more minutes before it drops. It has always done this from day one.

I don't have another wireless network close by that I could test it on. I'm a little isolated. i might be able to work out a time when I could take it by a friend's house, but he's over an hour away.
I have a Win 7 laptop, a Win XP desktop and an old Mac Powerbook as well as an iPod Touch and iPad 3 that use my wireless network without any problems - besides the fact that hardly any of my devices will talk to the other... But that's an OS issue. They all see the network, and the printer after I cycle the power on it.
My wireless router is a Netgear WNR2000. I remember monkeying with the channels when I frist got this printer a few months ago, but I don't remember what all I did. Since I did a firmware update on the router, the channel is now set to Auto. If there's a channel you think I should try, let me know what it is. The printer shows up on the list of devices in the router, but that may be because I have its address reserved for the static IP. Interestingly, the router sees the printer, even though my devices cannot. I did a ping just now while checking that, and got this - which is unusual. Normally they all time out.
Pinging 192.168.1.150 with 32 bytes of data:
Request timed out.
Request timed out.
Reply from 192.168.1.150: bytes=32 time=3223ms TTL=255
Request timed out.
Ping statistics for 192.168.1.150:
    Packets: Sent = 4, Received = 1, Lost = 3 (75% loss),
Approximate round trip times in milli-seconds:
    Minimum = 3223ms, Maximum = 3223ms, Average = 3223ms
Played around a bit more pinging between devices and got this oddity - without a power cycle just a couple minutes later.
ping 192.168.1.150 -n 50 -l 500
Pinging 192.168.1.150 with 500 bytes of data:
Reply from 192.168.1.150: bytes=500 time=527ms TTL=255
Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
Reply from 192.168.1.150: bytes=500 time=12ms TTL=255
Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
Reply from 192.168.1.150: bytes=500 time=21ms TTL=255
Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
Reply from 192.168.1.150: bytes=500 time=21ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
Reply from 192.168.1.150: bytes=500 time=22ms TTL=255
Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
Reply from 192.168.1.150: bytes=500 time=22ms TTL=255
Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
Reply from 192.168.1.150: bytes=500 time=9ms TTL=255
Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
Ping statistics for 192.168.1.150:
    Packets: Sent = 50, Received = 50, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 9ms, Maximum = 527ms, Average = 26ms
Is there a possibility that the printer is going into a standby state and having trouble waking when traffic hits? I don't know if that's possible, just seems like it looking at this.

In Yosemite, I can;t operate for more than a few minutes with Keychain or Safari asking for my login password. How can I turn this off, and still be safe?

Using Yosemite, I an't seem to work for more than a few minutes without being asked for my login password. Keychain wants it, Safari wants it, iCloud wants it..the list goes on. Then in 10 minutes or so, they all want it again. Passwords are being stored by Safari as usual, but new tabs or pages bring up the request. How can I turn this off and still have protection?

Tutorial: Resolving Keychain Issues
If you can't access your keychain, or forget your password If you can't get into your keychain file because you've forgotten your password or the keychain file appears to be corrupt, there are a couple of options.
First, if you've forgotten your password, you can use the "Keychain First Aid" utility to make the keychain password the same as the login password. This can be accomplished via the following process:
1. Open Keychain Access (located in Applications/Utilities)
2. Go to the "Keychain Access" menu and select "Preferences"
3. Click the "First Aid" tab
4. Make sure the "Synchronize login keychain password" box is checked
5. Close the Preferences window
6. Go to the "Keychain Access" menu and select "Keychain First Aid"
7. Enter your username and password
8. Click the "Repair" button
The second option is to completely delete your keychain then recreate it. This routine is useful if your keychain appears to be corrupt or otherwise inaccessible. This can be accomplished as follows:
1. Launch Keychain Access (located in Applications/Utilities)
2. Click "Show Keychains" in the lower-left corner of the window.
3. Select the problematic keychain from the left-hand pane.
4. Navigate to the "File" menu and select "Delete Keychain '(name of keychain)'"
5. Check all options for deletion and press "OK"
6. Create a new keychain by going to the "File" menu, then "New" and selecting
"New Keychain"
7. You can now make this keychain your default if you desire by selecting it, then
going to the "File" menu and selecting "Make '(name of keychain)' Default"
Login as root and perform repair In some cases, problems with keychains can only be resolved when logged in as the root user.
First, you want to enable the root user:
1. OS X Mountain Lion: Enable and disable the root user
2. OS X Lion: Enable and disable the root user
3. Mac OS X 10.6: Enabling the root user
4. Enabling and using the "root" user in Mac OS X
After enabling the root user, and logging in under this account, again open Keychain Access. First attempt repairs using Keychain First Aid, and failing that, delete then recreate the keychain as described above while logged in as root.
Persistently asked for stored passwords If you are persistently asked for passwords in various applications that you have specified should be remembered in a keychain, your "login" keychain may not be active for one reason or another.
Navigate to ~/Library/Keychains/ (this is the Library folder inside your user's home folder). Find the file named "login.keychain" and double-click it.
Failing that, select the "login" keychain within the Keychain Access application and make sure it is the default keychain by going to the "File" menu and selecting "Make 'Login' Default"
Turn off Keychain synchronization in applications having problems If specific applications are experiencing issues when accessing password-protected material, the Keychain may be to blame.
The above comes from an article published on MacFixit.com.

After installing the 8.1 update the Internet Sharing won't allow any devices to stay connected for more than a few hours.

Internet sharing is turned "on" and appears to be working, but really isn't. Locking the screen, restarting, or a hard reboot helps, but it is extremely aggravating not to be able to maintain a connection for more than a few hours at a time!

Thank you so much for the info! I apologize for having asked for your device model as that is the forum you posted to. Also, I know that we've set the expectation that the device will remain connected as long as a demand for signal flows through it, but that may not be entirely the case. After a period of constant use, any device (including the Lumia 822) may require or force itself to stop.
You've mentioned that the device will freeze after a few hours usage. Is the device also connected to the charger while being used as a hotspot? If so, do you notice the device getting warmer than it normally would be?
DionM_VZW
Follow us on Twitter www.twitter.com/vzwsupport

Playing music through nano and auto stereo, while traveling...nano is set to shuffle, but if vehicle is stopped for more than a few minutes, nano restarts with same song everytime! How do I make it really shuffle the songs

Having trouble with Nano shuffle while traveling. It's connected to my vehicle stereo and set to shuffle. When I stop the vehicle for more than a few minutes, the music resumes with the same song it always starts with. How can I get it to keep shuffling after restarting the vehicle?

Is the iPod actually doing the music playing? If the iPod is connected using a USB port (on the car audio system) and docking cable, the car audio system is doing music playing. The iPod is just acting as a storage device (like a USB flash drive) with song files. So, in that setup, it does not matter whether the iPod is set to shuffle or not, because the car audio system is playing the songs. Any change to how it plays songs would have to be a setting on the car audio system.

My iPhone5 has terrible Network connection. It rarely works at the normal speed-if ever. I usually get 3G or 1x network dozens of times a day. My phone also gets pretty hot when i try to use any data for more than a few minutes.

My iPhone5 network connection has been terrible for the past week and a half. My phone is no more than a year old so I don't see why it would be a problem with the phone. When I try to use the internet or look for apps or anything like that, anything that uses data really, it takes FOREVER if it even loads! Most of the time it won't even load. My network changes from LTE(which doesn't work well) to 3G(which works even less) and then to 1x(which basically doesn't work at all). This happens dozens of times a day. It's getting quite irritating. I've tried turning my phone off and letting it sit for a while and that does nothing. I'd really prefer NOT to restore my phone. What is the deal??!

Are you broadcasting your SSID? Sometimes this can cause a problem connecting. Is this Cisco router running any turbo modes or special preparatory protocols.
There are no know issues with Wi-Fi connectivity except on first connection; and the chance of 2 devices having the exact same issue is very unlikely. This sounds like something to do with your wireless router.
Have you tried to connect to another Wi-Fi hotspot elsewhere?
Do you have any 2.4 GHz wireless phones or security system that could interfere with connection?

If laptop is inactive for more than a few minutes, Firefox loses its connection and I must restart to get back online. How can I fix this?

This is a recent problem. It was working fine until a couple of weeks ago. If I restart the computer, Firefox gets online with no problem. However, having to do this every time I walk away from my desk is becoming annoying....Is there a way for me to fix this? I am not a techie but I am good at following directions, so any advice would be appreciated. Thanks!

your solution to my question was both helpful and not helpful it was very helpful on my computer which is a windows 7 it allowed me make some adjustment although i am for the most part really good about shutting mine down after i use it there are times that i do leave it on planning getting back to it forgetting or get caught in something else
but unfortunatly it wasn't helpful on the computer i really need to set it up on which is a windows xp home who's power options r already suppose to be set up to shut down the computer if idle for 1 hour but it never does
since posting my question i have gone through any section of help n support on that computer that pertains to it. i have also been into the microsoft support site to try and configure auto logoff n auto poweroff if computer is idle for a while but when i tried to find the files on that computer they said i needed to access to set it up don't exist and of course way at the bottom of the page is operating system this applies to and you click on it and it states for xp professional only and that the support for the xp home in this matter is no longer available on their site

MSI GX630 - My turbo will not stay on for more than a few seconds

I have the laptop plugged in to AC and when I enable the turbo , it says turbo on then almost immediatly it says turbo off and turns back off. Some times it will stay on for up to about a min, but it never will just stay on. Do I have a bum cpu that can't handle the over clocking, overheats, and then it automatically reverts back to normal cpu speed or what? Anyone else have this problem? It is not that big of a deal, but if they are going to sell a laptop with a turbo option, I think they should test it to make sure that it works with something that taxes the cpu and can handle it.

See here about EC Reset ==> https://forum-en.msi.com/index.php?topic=112416.0

Why IPhone is getting hot when downloading via wifi and how to turn off itunes 11.1 launch automatically when plugged in Iphone to the PC

Why IPhone is getting hot when downloading via wifi and how to turn off itunes 11.1 launch automatically when plugged in Iphone to the PC

My brother with the iPhone 4 suffers from that too.
My iphone 5 doesnt however.
But to Stop Launch when your apple device is connected, 1. connect your iPhoneto your computer, 2.Go to the Summary Page, 3. uncheck the box "Open iTunes when this iPhone is connected" and then your good for that device.

My Iphone 5 keeps restarting over and over. it wont stay on for more than a minute. how do I fix this?

My Iphone 5 keeps restarting over and over. it wont stay on for more than a minute. how do I fix this?

Contact Apple Support or an Apple Store if you have one near you. Your battery needs to run through the diagnostic test. You can also try to put the device into Recovery mode as well and rsetore the iOS software, and set up the device as new. Follow this article on Recovery Mode:
http://support.apple.com/kb/ht1808

My iphoto quites unexpectedly everytime I open it and says closes while using the eOkaoFr.dylib plugin. Does anyone know how to fix this? iphoto won't stay open for more than 1 minute at a time.

My iphoto quites unexpectedly everytime I open it and says closes while using the eOkaoFr.dylib plugin. Does anyone know how to fix this? iphoto won't stay open for more than 1 minute at a time. Help anyone?

Is there a crash log? If so post the first 100 or so lines o fit
Do you know what the ofending plugin is? and where it came from?
LN

After downloading updates for the first time, i was asked to restart my mac. it starting writing configuring installation. the staus bar just showed a little and remained like that for more than 3 hrs. i tried several times wit no success.

after downloading updates for the first time, i was asked to restart my mac. it started writing configuring installation. the staus bar just showed a little and remained like that for more than 3 hrs. i tried several times wit no success. it has not updated my mac OS X 10.5.

My clean install worked out alright, although I don't think it really fixed anything, rather gave me a couple more days of use 'till I have to send it in. Someone please help my get it running properly again...

Iphoto won't stay open for more than a second

My iphoto won't stay open for more than a second. What could be wrong?

You can see more than any of us here. If there is no other indication beyond what you have described, then it could be anything. We don't even know if you have somehow deleted the application.

FCP 5 won't stay open for more than a minute

First I upgraded from Quicktime to Quicktime Pro to convert .avi's to .mov's. That worked for about three weeks then suddenly all converted files played without any sound. Now after editing an mp4 on FCP I decided to upgrade the media to avi, so I upgraded the mp4 to avi using VisualHub, whose output plays fine in Quicktime (with sound), but while editing it together in FCP I've started to have problems while trying to integrate FCP with LiveType. I have to save after every change to the sequence. After integrating a LiveType file into FCP I found FCP shuts down after running for a minute, regardless of what I'm doing with it.
I'm currently working on an iMac Intel Duo and hope this doesn't rise out of a non-universal version of FCP running on an intel processor (perhaps a problem with Rosetta). If so I might have to upgrade to FCP 5.1
Any ideas?

How would I check the pixel dimensions?
With the mp4 they were copied off of a dvd with a program called Handbrake (it copies DVD's onto your iPod), though often whatever I get out of Handbrake I also have to put through a program called moviepod (which converts media files into mp4 format and once the conversion's done it appears on your iTunes browser).
I recently purchased a DVR which can load DVD's into the computer through multiple formats but then the DVD was rented and I figured I just as well use the media I already had in my computer.
Oh, and by the way, Thank you for the help so far. Though I'm afraid there's no clear resolution in sight I appreciate your apt attention.
The avi media is just the mp4 media converted through VideoHub (I've had no luck with either .avi or mp4 files using Compressor). The problem with editing may rely in my choice of converting programs and not FCP at all (the truth is I don't know much about these programs, outside what I use them to do (convert media) ).

Droid X battery will not stay charged for more than 5 minutes. Help

My Droid X will not hold a charge for more than 5 min. 1 phone call and the phone shuts down.

bdsutton,
Thanks so much for your inquiry! There hasn't been a software update for the Droid X since 2/16/12.
I would like for you to put the device in Safe Mode http://bit.ly/OAXCYh and then check your email to see if it still turns off.
Safe Mode temporarily disables all applications that have been installed via the Android Market. Performing this troubleshooting step is necessary to determine whether a 3rd party application is the cause of an Operating System / Application issue.
I want you to try that to see if there is something else affecting why the phone battery goes low only when you check email.
Tamara H.
Follow us on Twitter @VZWSupport

I was mid facetime call and my phone turned off and wouldnt turn on until i plugged it in. then the date was wrong,it said no service, and wont let me turn wifi on. also it wont stay on for more than a few minutes at a time

Similar Messages

Maybe you are looking for