Iam using 3015 network printer. while iam printing from word it is taking too long to print

Respected sir,
I am using 3015 printer.  when ever i give print it is taking too long time nearly 1 minute . there is no problem with the network

Let's set a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). You can find the DHCP range of the router using its internal settings page or in its manual. Use the CD that came with your router or type the router's IP address (ends in .1) into a browser.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway and first DNS. Leave the second one blank.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

  • How do I print to wifi printer while keeping data from cellular?

    How do I print to wifi printer while keeping data from cellular?

    If you print to a WiFi printer no Cellular Data will be used.

  • Firefox browser taking so long to print html report

    I am using Firefox 18.+ version on Windows XP machine. My application is reporting tool. Whenever I try to print the html report, the firefox browser is taking close to 4min to start printing the page. The same report getting printed in Crome browser within few seconds. IE browser is taking close to 30 seconds. I tried followed the steps provided by the Mozilla support team
    (https://support.mozilla.org/en-US/kb/fix-printing-problems-firefox?esab=a&s=slow+printing&r=0&as=s ).
    But there is no improvement. I verified that the printer has no issues, only in Firefox its taking very long time to send the document to printer.
    Thanks for your help.

    I'm not sure we can investigate this properly without access to the report, which I assume is not readily available to the public...
    Could you test in a "clean" Firefox profile and see whether you can replicate the problem there? To do that, use the profile manager:
    * Exit Firefox
    * Start > Run > firefox.exe -P {ENTER}
    * Create a new profile with the default location setting
    * Start Firefox in the new profile and try to print
    Any difference?
    To switch back to your normal profile, exit Firefox, restart the profile manager and start up in your regular profile. You can return to your previous point using History > Restore Previous Session (assuming it was not a private session).

  • I am in an internet cafe and my macbook pro can't find the wireless network available here. I have used this network before. I have restarted my machine several times too. help please

    I am in an internet cafe and my macbook pro can't find the wireless network available at the cafe. I have used this network before. I have restarted my machine several times too. help please

    Change your router channel.  Sometimes this is all you will have to do.
    Power cycling the router.  Read the router's user manual or contact their tech support for instructions.
    System Preferences/Internet & Network/Network
    Unlock the padlock
    Locations:  Automatic
    Highlight Airport
    Click the Assist Me button
    In the popup window click the Diagnostic button.
    System Preferences/Network- Unlock padlock.  Highlight Airport.  Network Name-select your name.  Click on the Advanced button.  Airport/Preferred Networks-delete all that is not your network.
    Place a check mark next to "Remember networks this computer has joined."  Click the OK button and lock the padlock.  Restart your computer.
    http://support.apple.com/kb/TS1920 Mac OS: How to release and renew a DHCP lease
    No internet connection (wireless)
    Check to see if an extra entry is present in the DNS Tab for your wireless connection (System Preferences/Network/Airport/Advanced/DNS).
    Delete all extra entries that you find.
    Place a check mark next to "Remember networks this computer has joined."
    Other resources to check into:
    http://www.netspotapp.comNetspot
    How to diagnose and resolve Wi-Fi slow-downs
    Pv6 troubleshooting
    Mac OS X 10.6 Help:  Solving problems with connecting to the Internet
    What Affects Wireless Internet?
    Solutions for connecting to the Internet, setting up a small network, and troubleshooting

  • Network event is taking too long (100%)

    Hi everybody. We have a 10g DB on Windows. We're using OEM to manage the DB, and it has started to show an alert about database time spend waiting for "Network" event. It arises when we execute one module that updates several tables, that is taking too long. Before we had this app on 8i, also on Windows, and that operation was much more faster than now. The indexes on tables are valid, and I've gathered statistics for the CBO, so I suppose the problem is, as the OEM says, related with network, but I don't know why, because the connection speed is the same tan before, and the two machines are in the same LAN.
    Any ideas??

    Here is the output requested:
    SQL> select * from v$system_event
    2 where event like 'SQL%';
    EVENT TOTAL_WAITS TOTAL_TIMEOUTS TIME_WAITED
    AVERAGE_WAIT TIME_WAITED_MICRO EVENT_ID
    SQL*Net message to client 1159200 0 252
    0 2516408 2067390145
    SQL*Net message to dblink 2234 0 1
    0 5590 3655533736
    SQL*Net more data to client 5753 0 166
    0 1657387 554161347
    EVENT TOTAL_WAITS TOTAL_TIMEOUTS TIME_WAITED
    AVERAGE_WAIT TIME_WAITED_MICRO EVENT_ID
    SQL*Net more data to dblink 12 0 0
    0 548 1958556342
    SQL*Net message from client 1159181 0 218341084
    188 2,1834E+12 1421975091
    SQL*Net more data from client 23299 0 180602
    8 1806015123 3530226808
    EVENT TOTAL_WAITS TOTAL_TIMEOUTS TIME_WAITED
    AVERAGE_WAIT TIME_WAITED_MICRO EVENT_ID
    SQL*Net message from dblink 2234 0 3693
    2 36934861 4093028837
    SQL*Net more data from dblink 4021 0 39
    0 390002 1136294303
    SQL*Net break/reset to client 182986 0 2740
    0 27397165 1963888671
    9 filas seleccionadas.

  • I have the converter to change pdf to word. Works sometime, other time says conversion is taking too long. Can I get what it has translated so I can use the parts?

    I have the converter to change pdf to word. Works sometime, other time says conversion is taking too long. Can I get what it has translated so I can use the parts?

    I would ask in the ExportPDF forum, Adobe ExportPDF (read only) (assuming that's the service to which you have subscribed). This is the Reader one.

  • Printing taking too long

    Using java print APIs to print some labels and it's taking way too long. Creating the panels and sending them to the printer doesn't take too long, but once the app is finished and it has been sent the printer reads "processing job" for a long time before it prints. I've tried two printers, same results. Even very simple print jobs take a while. one printer was returning "internaloverflow or insufficientmemory" error. The document was only a page or two... ?
    Help please!
    -Andrew

    Hi,
    What is  your dot matrix printer model. You can change its quality to lower value but lower
    value or resolution makes printer fast but the output become low.
    Thanks.
    Clint

  • I can no longer print web site pages from my Firefox browser. I can still print web site pages from Internet Explorer.

    I tried the steps in the Firefox support area of resetting Print.Print_printer but that did not work. Whenever I try tp print a webpage the print preview page is blank and it freezes up. I then have to close the browser and start over. I can print webpages from Internet Explorer.

    See:
    *http://kb.mozillazine.org/Problems_printing_web_pages
    *https://support.mozilla.org/kb/Printing+a+web+page

  • Downloading printer it taking too long

    I am trying to download my new hp printer on my laptop. It has been scrolling for over 30 minutes. How long does it usually take?? hp 5740 e-all-in-one wireless

    Hello @gravesl, 
    Welcome to the HP forums.
    I understand that you are having a problem installing the software for your 5740.
    I would like to help.
    The install should not take that long. In my experience, setting up the printer for out of the box to finish, should be 20 minutes to half an hour.
    So that I may better assist you i would like to clarify something.
    What is taking a long time?
    Is it the actual installation, or are you downloading the software from HP.com, and that is what is taking so long?
    Aardvark1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!

  • Dynamic streaming taking too long time to switch video using NetStreamPlayOptions in AS3

    Hi,
         Can any one tell me why dynamic streaming taking too much time to switch video from lower bit rate to higher bit rate and vice versa.
    I am doing dynamic streaming in following ways -
    var param:NetStreamPlayOptions = new NetStreamPlayOptions();
    param.oldStreamName=oldStream();
    param.streamName=newStream()
    param.transition=NetStreamPlayTransitions.SWITCH;
    ns.play2(param);
    ns.addEventListener(NetStatusEvent.NET_STATUS, switchMode);
    I am using duel buffering and that is 3 seconds when video starts and 10 seconds when "NetStream.Buffer.Full". Video taking approximately 30-50 seconds to switch video and when I am calling the above code.
    Thanks & regards
    Sunil Kumar

    Hi Sunil,
    Was my link useful to you? If you have not gone through the link which I suggested just go through the below lines it may help you:
    For a faster switch with optimal keyframe interval and client-side buffer, when Flash Media Server (FMS) receives a "switch" command, the server waits for a keyframe to switch to the new stream. FMS looks for the keyframes in the new stream in chunks equal to the client's buffer size(NetStream.bufferTime), so having a client buffer larger than the keyframe interval of the stream would help with a fast switch response time from the server—in other words, a shorter delay between a "switch" call to the server and the client receiving bits from the new stream in response.
    Following values are considered most optimal:
    Keyframe interval: 5 sec.
    Client-side buffer: 6–10 sec.
    So to maintain optimal keyframe interval you can go for fresh encoding of your videos which will give you a chance to set keyframe interval or if you dont want to do this then I would suggest you to increase the client-side buffer.
    Regards,
    Amit

  • Keep italics while styling text from Word

    I have a long book with loads of endnotes. I've gotten them to come in with italics preserved. However, I still need to reset the styles for them. But any change kills all italics. Is there a way to re-style the text in general and preserve the existing italics? There are hundreds of these, so going back to touch every one is an evil undertaking.

    Will do. In this case, I just needed to maintain italicized titles within endnotes. All of the endnotes are being stripped from their sections of this book and compiled in their own section in the back. So, once I bring in the content, I'm free to move them around. The issue has always been that my client never quite follows the style rules they are given to make the process flow easier. They overlap styles, apply random fonts, etc which I have not been able to get InDesign to suck in and map correctly. So, while the endnote style I mapped is applied to all of them, they still have a bogus Times Roman font applied on top. When I option + click my style, it kills off the italics in the reference titles. Same happens for the endnote reference numbers sometimes.
    But, you're Find + Replace steps worked perfectly. I now know a little bit more about Find + Replace strategy. If I did more pubs of this sort, I would surely like to find ways to cut off all this issues at the pass. This pub occurs biennially so, the pain and proposed solutions fade between hits. All of the data in the pub, we have split out in Excel, which works great–tables, charts, graphs etc.
    This is number 4. If the fifth one is on the table in 2012, or any others that may occur, do you have any recommended reading that covers a solid process for handling 200+ pages of endnoted content from Word...besides relying on clients to actually follow the instruction provided to them?

  • Accessing Tables using global index rowid is taking too long.

    I am using Oracle 10.2.0.4.0. I am having tables which are ~100+GB in size which is range partitioned on a date column and hash subpartitioned on primary key column. And accessing these tables using global index row id using idex range scan( size of those indexes are ~7+ GB) taking ~5+ mins which results in ~1000 rows as out put. So is this means there is some structural problem with tables/indexes or its something issue at block level? How to dig more into this issue?

    Hi,
    930254 wrote:
    I am using Oracle 10.2.0.4.0. I am having tables which are ~100+GB in size which is range partitioned on a date column and hash subpartitioned on primary key column. And accessing these tables using global index row id using idex range scan( size of those indexes are ~7+ GB) taking ~5+ mins which results in ~1000 rows as out put. So is this means there is some structural problem with tables/indexes or its something issue at block level? How to dig more into this issue?once you get a chance to run the query and collect some diagnostic info, here are the questions that you should ask yourself:
    1) where is the 5 mins spent? doing index range scan itself, doing table index access by global rowid, waiting for something, doing something else?
    2) how many reads are there and what kind (logical, physical, direct path)? per the entire query and per index range scan
    3) is there any aggregation in the query? if there is, then 1000 rows output doesn't mean anything -- you could have to access millions or billions of rows to produce a 1000 row output in an aggregate query
    The best tool to answer these questions is dbms_xplan.
    Best regards,
    Nikolay

  • Since the last update of firefox, the time has been 25 to 35 seconds to enter bookmarks or even the time it takes to page down when it used to take a few seconds. can you check why it taking so long since the update on firefox.

    since the last update a few days ago of firefox, the time has been 25 to 35 seconds to enter bookmarks or even the time it takes to page down when it used to take a few seconds. can you tell me why it taking so long since the update on firefox. may another update is in order.

    I have now done pretty much every suggestion that even vaguely applies in the various helpful link provided. Thanks for the ongoing help. =)
    I have managed to get FireFox's start-up memory usage down to about 100,000K, however it appears that memory usage keeps creeping up the longer FireFox is open. (It seems to top out around 500,000K.) And I'm not talking open for many hours or days - but rather for minutes and possibly up to a couple hours. (Based on how long I've been fiddling with all this so far.)
    On the plus side, it does not appear GreaseMonkey is the culprit since with it active or disabled this memory creep still occurs. Although having GreaseMonkey enabled definitely increases the rate of memory creep. Though once it has creeped up to 150,000+K, disabling GM does not make it drop back down to the starting 100,000K.
    I should point out I run a MacBook Pro and use Bootcamp to partition the hard drive and run it as a Windows 7 PC about half the time. I am running it literally as a PC or, alternately, as a Mac depending on which hard drive I choose to load. (I'm not "windowing" it.) This problem exists regardless of whether I am using the PC or the Mac. These repairs have been made currently on the PC side, and I will attempt them all again on the Mac side. I find it odd that this enormous memory drain has occurred on 3 different computers at the same time. (The two "halves" of my home laptop as well as the PC at my work place.)

  • A1000 phase taking too long while upgrading from R12.2.0 to R12.2.4

    Hi
    I am running the final R12.2.4 upgrade patch (patch# 17919161), and it is presently running the A1000 phase. Its been over 10 hours now it is stuck at the same phase. I have installed R12.2.4 a couple of times now but this is the first time it is taking so long to finish.
    Looking at the workers using adctrl, it gives the following output. Anyone knows how to expedite this processing?
            Control
    Worker  Code      Context            Filename                    Status
         1  Run       Generic R120       QPXCONAT.pll                Running
         2  Run       Generic R120       QPXPTMAP.pll                Running
         3  Run       Generic R120       QPXFMLMT.pll                Running
         4  Run       Generic R120       QPXQPCDT.pll                Running
         5  Run       Generic R120       QOTLNSRF.pll                Running
         6  Run       Generic R120       QPXQPCUR.pll                Running
    Regards
    Kabeer

    Never mind. Here's the resolution:
    Step1. Use adcrtl utility to quit all the workers in 'running' status
    Step2. Drop table applsys.FND_INSTALL_PROCESSES
    Step3. Restart patch application using ADOP utiloty with parameter "restart=yes"
    So now the patch application has resumed.
    Regards
    Kabeer Khan
    www.aclnz.com

  • HT4059 Using my iPad 1, viewing a page from a book purchased through iBooks, want to print a page.  Does anyone know how??

    I'm using my iPad 1 and wanting to print a page from a book that I purchased from iBooks.  I can't figure out how to print.  Any suqqetions? Thanks.

    Sorry, but you can't.
    Regards.

Maybe you are looking for